SY88808LMH - 10.3Gbps CML 1Tx/1Rx | Microchip
料号: SY88808LMH ✓ 量产中SY88808LMH 概述
A high-speed transceiver is an interface IC that combines a serial transmitter and receiver into one package. CML means current-mode logic, a differential signaling method commonly used when data must be transferred reliably at multi-gigabit rates. Within the broader semiconductor hierarchy, the SY88808LMH is a bus transceiver, interface IC, communications device, and signal-conditioning component rather than a general-purpose logic or memory device.
Key characteristics include a 3.3 V supply, one transmit channel, one receive channel, a maximum stated data rate of 10.3 Gbps, and integrated equalization. The single-channel arrangement supports point-to-point links where one endpoint transmits, the other receives, and the reverse direction may use another transceiver. The 28-pin VQFN provides a compact surface-mount footprint, while its exposed thermal pad supports heat transfer into the PCB when the link operates continuously.
The equalization function is the principal signal-integrity feature identified for this device. Its role is to compensate for frequency-dependent attenuation in cables, PCB traces, connectors, and other interconnect media. This makes the receiver useful in installed systems where edge degradation could otherwise reduce eye opening or cause data errors. Designers must still evaluate insertion loss, return loss, impedance continuity, connector transitions, and the complete channel budget rather than treating equalization as a substitute for controlled PCB routing.
Typical uses include high-speed backplanes, point-to-point serial links, test and measurement systems, data-conversion equipment, and communications infrastructure. The 1Tx/1Rx organization is appropriate when the design requires a compact full-duplex link assembled from two transceivers, one for each direction. In a full-duplex implementation, the two devices communicate differentially and require independent transmit and receive paths even though each device contains both functions.
Layout is critical because the device operates at rates as high as 10.3 Gbps. Use controlled-impedance routing, minimize stubs and layer transitions, place decoupling close to the supply pins, and provide a continuous ground reference beneath the package. Thermal-pad attachment should follow the manufacturer land pattern, and exposed-pad vias should be selected to balance electrical return paths, mechanical stability, and heat dissipation.
This product page combines the confirmed device description, package information, sourcing references, application guidance, and strict replacement screening. Its engineering value is the separation of confirmed specifications from unavailable details, helping engineers determine whether the 10.3 Gbps CML interface, equalizer, VQFN footprint, and packaging meet their board-level requirements.
直接替换替代料: SY88808LMH ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料SY88808LMH 规格参数
| Product Type | High-speed CML bus transceiver |
| 电源电压 | 3.3 V |
| Maximum Data Rate | 10.3 Gbps |
| Transmitter Channels | 1 |
| Receiver Channels | 1 |
| Logic Type | CML |
| Equalization | Integrated receiver equalization |
| 封装 | 28-pin VQFN |
| Package Dimensions | 4 x 4 x 0.9 mm |
| Exposed Pad | Yes |
| Shipping Package | Tube |
| 安装类型 | Surface mount |
SY88808LMH tube 引脚配置指南
SY88808LMH(tube 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: SY88808LMH.
请参阅 数据手册 以查看完整引脚配置。
典型应用
SY88808LMH 适用于 6 应用s: 10.3 Gbps Point-to-Point Serial Link, High-Speed Backplane Interconnect, Communications Test Equipment, Data Acquisition and Conversion, Industrial High-Speed Sensor Link, High-Speed Equipment Interconnect.
10.3 Gbps Point-to-Point Serial Link
The SY88808LMH fits point-to-point links requiring one transmit channel and one receive channel at rates up to 10.3 Gbps. Its 3.3 V CML interface allows two devices to form a bidirectional communication path, with each device handling one direction. The integrated receiver equalization can improve tolerance to frequency-dependent interconnect loss, although channel margin must be confirmed through simulation and hardware testing. Controlled-impedance routing, matched differential pairs, suitable termination, and a continuous ground plane are necessary at this data rate.
High-Speed Backplane Interconnect
The SY88808LMH can support short-reach backplane links where loss, jitter, and reflections are carefully controlled. Its maximum stated rate of 10.3 Gbps and integrated equalization provide useful margin for channels containing PCB traces, connectors, and vias. The designer should characterize the complete interconnect rather than estimate loss from trace length alone. Keep layer transitions and stubs under control, maintain differential impedance, and verify that the selected equalization setting remains valid across manufacturing tolerances and temperature.
Communications Test Equipment
The SY88808LMH is appropriate for communications and test-equipment modules that need a compact 10.3 Gbps CML interface with equalization. One transmitter and one receiver make the device convenient for loopback, channel characterization, and signal-conditioning experiments. Instrumentation designers should prioritize low jitter, stable reference distribution, repeatable termination, and isolated high-speed test paths. The exposed pad should be connected to the ground plane through the recommended via pattern to maintain electrical return continuity and thermal performance.
Data Acquisition and Conversion
The SY88808LMH can connect high-speed acquisition, processing, or conversion subsystems when the external architecture supports CML signaling. Its 10.3 Gbps capability handles single-lane data streams, while receiver equalization helps address attenuation introduced by board and cable interconnects. Clocking, data polarity, lane initialization, and device-specific control behavior must be implemented according to the manufacturer datasheet. The compact 28-pin VQFN also leaves board area available for other conversion and processing circuitry.
Industrial High-Speed Sensor Link
The SY88808LMH may be used in industrial equipment that transfers sensor or controller data over a short, controlled CML link. The 3.3 V supply and receiver equalization are useful in systems where cable or PCB loss changes with installation geometry. Industrial suitability must be assessed independently for temperature range, vibration, EMC performance, and long-term availability. Designers should also consider whether a lower-rate standard would provide a simpler and more robust interface when 10.3 Gbps bandwidth is unnecessary.
High-Speed Equipment Interconnect
The SY88808LMH supports equipment-to-equipment connections where a compact, high-rate differential interface is required. Its 1Tx/1Rx configuration allows local transmit and receive functions within one package, and the 10.3 Gbps rate supports single-lane streaming between closely coupled subsystems. Equalization can assist with installed interconnect loss, but successful deployment still requires a channel model covering connectors, dielectric materials, skew, and impedance discontinuities. A test article should verify eye opening and jitter before volume deployment.
工程参考数据: SY88808LMH ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Manufacturer | Microchip Technology |
| Package | 28-pin VQFN, 4 x 4 x 0.9 mm |
| Supply Voltage | 3.3 V |
| Maximum Data Rate | 10.3 Gbps |
| Transmitter Channels | 1 |
| Receiver Channels | 1 |
| Logic Type | CML |
| Equalization | Integrated receiver equalization |
| Exposed Pad | Yes |
| Shipping Format | Tube |
关键差异点
- Single-channel CML transceiver with integrated equalization (对比 General-purpose 10 Gbps serializers without receiver equalization)
- Compact 28-pin VQFN implementation (对比 Transceivers using larger leaded packages)
- Direct 10.3 Gbps single-lane operation (对比 Lower-rate CML interface devices)
设计说明
Use the manufacturer land pattern and preserve a continuous ground reference beneath the 28-pin VQFN. Keep the transmit and receive differential pairs short, matched, and referenced to a consistent ground plane. Avoid stubs, unnecessary vias, and abrupt layer changes because these discontinuities can degrade a link operating up to 10.3 Gbps. Confirm the final stack-up and controlled-impedance geometry during PCB design rather than after fabrication.
Connect the exposed pad to ground using the recommended via arrangement so that high-frequency return current and heat removal share a low-impedance path. The exposed-pad vias should be checked against assembly constraints for solder fill and mechanical reliability. Continuous data traffic can create more heat than intermittent operation, so the pad and via pattern should be evaluated together with the enclosure temperature and board copper area.
Validate the complete receiver channel rather than relying only on nominal data rate. Simulations and measurements should include trace and connector loss, differential skew, reflection, jitter, and the available equalization range. The SY88808LMH receiver equalization can assist with channel attenuation, but incorrect settings or an unsuitable channel topology can still reduce eye opening. Use compliance masks and eye measurements that correspond to the deployed data rate.
Do not treat SY88808LMH and SY88808LMH-TR as different electrical devices without checking the ordering table. Their confirmed listing difference is tube versus tape-and-reel format. For either ordering code, verify temperature grade, lead finish, traceability, and exposed-pad details. Also avoid assuming that a superficially similar 10 Gbps transceiver is interchangeable because differences in package, equalization, clocking, or pin assignments can prevent operation.
合规信息
No compliance declarations or qualification statements were confirmed in the manufacturer and distributor product information. Confirm RoHS, REACH, lead-finish, halogen, conflict-minerals, and automotive qualification status from Microchip Technology before production release.