Microchip Technology

SY88843VMG - 3.2Gbps CML Post Amplifier | Microchip

料号: SY88843VMG ✓ 量产中
3.3 V or 5 V Vdss 16-pin VFQFN with exposed pad, 3 mm x 3 mm Package
最小起订量: 1 |

SY88843VMG 概述

The Microchip SY88843VMG is a single-channel CML limiting post amplifier operating from a 3.3 V or 5 V supply and supporting data rates up to 3.2 Gbps. The device provides a 38 dB differential gain, a 2 GHz 3 dB bandwidth, 50-ohm CML data outputs, and a 800 mVpp output swing in a 16-pin VFQFN exposed-pad package. Its low-power design also includes TTL shutdown control for systems that require controlled output disabling.

A limiting post amplifier belongs to the high-speed amplifier family within the broader signal-conditioning IC category. Its primary role is to restore the amplitude and edge quality of a high-speed digital signal after losses caused by connectors, PCB traces, clock dividers, or other circuit elements. The SY88843VMG combines a multi-rate limiting amplifier with CML output stages in one compact package, providing the final signal-conditioning function in many optical and serial-data communication links.

The amplifier supports operation up to 3.2 Gbps and offers a wide gain-bandwidth relationship, including 38 dB differential gain and a 2 GHz 3 dB bandwidth. The 50-ohm CML outputs produce approximately 800 mVpp swing with 60 ps edge rates. For timing-sensitive links, the device specifies 5 psRMS typical random jitter and 15 psPP typical deterministic jitter. These characteristics help maintain usable rise and fall times when the signal must be delivered across a board-level interconnect.

Internally, the limiting stage converts small input-voltage variations into a standardized digital output amplitude. This fixed-amplitude behavior prevents accumulated noise or attenuation from changing the logical level presented to the receiver. The 3.3 V and 5 V supply options allow the amplifier to be used in both legacy 5 V backplanes and lower-voltage next-generation systems, while TTL shutdown provides a standard logic-controlled way to inhibit the outputs when the link is inactive.

Typical uses include optical-network transmit and receive paths, backplane and chip-to-chip serial links, clock and data retiming circuits, and other telecommunications equipment that handles multi-gigabit data. The 16-VFQFN exposed-pad package also makes thermal management an important part of the layout. The exposed pad should be connected to a low-impedance ground plane and evaluated against the maximum operating temperature of the finished system.

For a robust layout, route the high-speed differential inputs and CML outputs over controlled-impedance traces with short connections, provide solid return paths, and keep decoupling capacitors close to the supply pins. Treat the differential pair as a controlled-impedance transmission line rather than as two independent point-to-point connections. Avoid adding large stubs or test-point structures directly to high-speed nodes because they can degrade edge rate and jitter performance.

This page organizes the operating speed, gain, bandwidth, output-interface, jitter, and package information for SY88843VMG alongside application guidance, layout cautions, and sourcing references. Because this high-speed amplifier is sensitive to parasitics and thermal conditions, engineers should use the complete manufacturer datasheet for the final pin assignment, absolute maximum ratings, recommended circuit, and layout guidance before releasing a production board.

直接替换替代料: SY88843VMG ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

该产品暂无直接替换替代料。

请求替代料

SY88843VMG 最大额定值与电气特性

Product Type Single limiting post amplifier
电源电压 3.3 V or 5 V
Maximum Data Rate 3.2 Gbps
Differential Gain 38 dB
3 dB Bandwidth 2 GHz
Output Interface 50 ohm CML
Output Swing 800 mVpp
Output Edge Rate 60 ps
Random Jitter 5 psRMS typical
Deterministic Jitter 15 psPP typical
Shutdown Control TTL shutdown
Amplifier Configuration Single channel
封装 16-pin VFQFN with exposed pad, 3 mm x 3 mm
安装类型 Surface mount
RoHS Compliance unknown
REACH Compliance unknown

SY88843VMG 16-pin vfqfn with exposed pad, 3 mm x 3 mm 引脚配置指南

SY88843VMG(16-pin vfqfn with exposed pad, 3 mm x 3 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

SY88843VMG 的 16-pin vfqfn with exposed pad, 3 mm x 3 mm 封装引脚图

暂无详细引脚数据: SY88843VMG.

请参阅 数据手册 以查看完整引脚配置。

典型应用

SY88843VMG 适用于 6 应用s: Optical Network Receive Paths, High-Speed Backplane Links, Chip-to-Chip Serial Interfaces, Clock Distribution and Retiming, Telecommunications Line Cards, Test and Measurement Equipment.

🌐

Optical Network Receive Paths

The SY88843VMG is suitable for restoring a degraded high-speed differential signal at the output of an optical receiver or retiming stage. Its limiting function standardizes signal amplitude after upstream losses, while the 38 dB differential gain and 2 GHz 3 dB bandwidth support operation to 3.2 Gbps. The 50-ohm CML outputs with approximately 800 mVpp swing interface naturally with CML logic. In an optical link, place the amplifier close to the receiving device to minimize additional trace loss, and verify that the complete path meets the protocol's jitter and eye-margin requirements.

🖥️

High-Speed Backplane Links

Use the SY88843VMG as the final limiting stage of a multi-gigabit backplane link when connector and PCB losses leave the receiver input below its required logic level. The amplifier supports data rates up to 3.2 Gbps with 38 dB of differential gain, restoring signal amplitude while preserving 60 ps edge rates. Controlled-impedance routing is essential because discontinuities on the differential pair can increase reflections and degrade the recovered eye. The TTL shutdown input can disable the outputs during link inactivity, reducing unnecessary switching activity in a multi-lane backplane.

🔧

Chip-to-Chip Serial Interfaces

The SY88843VMG can condition high-speed data between chips when a loss or logic-level mismatch would otherwise compromise reception. Its single-channel architecture allows each direction of a differential link to use a dedicated limiting amplifier. Operation from 3.3 V or 5 V supports both older interface blocks and newer low-voltage fabrics. Because this is a post amplifier rather than a general-purpose comparator, the design should use controlled-impedance differential routing, short return paths, and supply decoupling close to the device to preserve its 2 GHz 3 dB bandwidth and specified jitter performance.

⏱️

Clock Distribution and Retiming

The SY88843VMG is applicable where a high-speed clock must be regenerated after passing through a lossy distribution element. The 38 dB differential gain restores amplitude, while the limiting output stage produces a consistent CML signal suitable for downstream clock receivers. The device's 3.2 Gbps multi-rate capability accommodates base and doubled-rate clocking schemes covered by the target protocol. Keep the input and output traces short and use symmetric routing to minimize duty-cycle distortion, and compare the measured jitter against both the device specification and the receiving clock's input tolerance.

🏭

Telecommunications Line Cards

Telecommunications line cards often combine long board-level interconnects with tightly specified CML interfaces, making the SY88843VMG suitable as a line-card output limiting amplifier. It operates from a 3.3 V or 5 V supply and supports rates to 3.2 Gbps, while the TTL shutdown input provides a direct way to inhibit outputs during board reconfiguration. The 16-VFQFN exposed-pad package supports compact designs, but the pad must connect to a low-impedance ground plane. Validate thermal performance and signal integrity across the full temperature range and across every supported line rate.

📟

Test and Measurement Equipment

The SY88843VMG can serve as a signal-conditioning element in high-speed test fixtures, pattern-generator interfaces, and measurement front ends that require a standardized CML output. The limiting action reduces sensitivity to amplitude variations in the source path, and the 800 mVpp output swing provides a defined level for downstream instrumentation. The 5 psRMS typical random-jitter specification is particularly relevant when characterizing test systems. Keep the amplifier out of long fixture cables and terminate the CML interface according to the manufacturer recommendations to avoid adding reflection-related jitter to the measurement.

What is the operating speed of the SY88843VMG?
The SY88843VMG supports data rates up to 3.2 Gbps. According to the manufacturer datasheet listing, the device is a 3.3 V or 5 V CML limiting post amplifier with multi-rate operation to 3.2 Gbps. It is intended for high-speed serial links where attenuation from interconnects or preceding circuit stages must be corrected before the signal reaches a receiver.
What is the gain and bandwidth of SY88843VMG?
The SY88843VMG provides 38 dB of differential gain with a 2 GHz 3 dB bandwidth. The manufacturer datasheet identifies this as a wide gain-bandwidth-product limiting amplifier. These two figures define its primary signal-conditioning capability: enough gain to restore a degraded differential signal and enough bandwidth to preserve fast data edges at multi-gigabit rates.
What output interface does SY88843VMG use?
The SY88843VMG uses a 50-ohm CML output interface. According to the manufacturer datasheet description, the outputs provide approximately 800 mVpp swing with 60 ps edge rates. CML is commonly used in high-speed serial communication systems because its low-amplitude differential signaling supports controlled-impedance routing and reduces susceptibility to common-mode noise.
What jitter performance does the SY88843VMG provide?
The SY88843VMG specifies 5 psRMS typical random jitter and 15 psPP typical deterministic jitter. These figures are important in serial links because timing variation directly limits eye margin. The datasheet values should be checked against the required mask of the target protocol, and actual channel loss, connectors, and PCB layout must also be included in the system jitter budget.
What supply voltages are supported by SY88843VMG?
The SY88843VMG operates from a 3.3 V or 5 V supply. This dual-voltage capability supports both conventional 5 V communication equipment and lower-voltage systems that require reduced power consumption. The selected supply must still satisfy all absolute maximum ratings and timing requirements listed for the device in the manufacturer datasheet.
Does SY88843VMG include a shutdown function?
Yes, the SY88843VMG includes a TTL shutdown function. The manufacturer describes the device as a low-power limiting post amplifier with TTL shutdown, allowing the outputs to be disabled with standard logic-level control. Use the shutdown state required by the system architecture and confirm its effect on output levels, timing, and power consumption during the design review.
Where can I download the SY88843VMG datasheet PDF?
The SY88843VMG manufacturer datasheet contains the authoritative pin assignment, recommended application circuit, electrical characteristics, and layout guidance. A distributor-hosted copy is listed by FindIC, while the Microchip cross-reference search provides a route to current Microchip product information. Download the document from the manufacturer whenever possible so that revision-specific limits and test conditions are preserved.
Where can I find the SY88843VMG pinout?
The SY88843VMG uses a 16-pin VFQFN package with an exposed pad. The complete pin names, exposed-pad connection, and recommended land pattern must be taken from the pin-description table in the manufacturer datasheet. Because this package is only 3 mm by 3 mm, assign every connection using the package drawing and verify the land pattern against the manufacturer layout guidelines before fabrication.
Where can I buy SY88843VMG online?
The SY88843VMG can be sourced through the Request a Quote form on this page, which connects buyers with the XAIPART sales team for current availability and order handling. The part is listed by Microchip Technology across major distributor catalogs. Submit the exact MPN, target quantity, and delivery requirement when requesting a quotation.
What is the price of SY88843VMG?
Current commercial terms for the SY88843VMG are handled through the Request a Quote form on this page. Because distributor pricing, stock, and lead time can change without notice, use that form for a current unit price and volume quotation. Provide the required package quantity, date code preference, and shipment destination for an actionable response.
What is the lead time for SY88843VMG?
Current lead time for the SY88843VMG should be confirmed through the Request a Quote form on this page. The device is actively cataloged by Microchip Technology and appears in distributor inventories, but future availability depends on production schedules, incoming inventory, and the quantity requested. State your required delivery date to obtain a schedule committed against the order.
Is SY88843VMG in stock?
The SY88843VMG is actively cataloged, but current stock for a specific quantity is confirmed through the Request a Quote form on this page. Inventory status can vary by package, date code, and order size, particularly for older communications components. Provide the complete MPN and required quantity so the sales team can check the matching supply position.
What is the best drop-in replacement for SY88843VMG?
No drop-in replacement is confirmed for the SY88843VMG from the available cross-reference results. A candidate must match the 16-VFQFN exposed-pad footprint, pin assignment, differential input interface, 50-ohm CML outputs, gain, bandwidth, shutdown behavior, and supply range before it can be treated as a drop-in part. Verify the complete datasheet rather than relying only on a similarity score.
Can SY88843VMG be replaced by a generic CML post amplifier?
A generic CML post amplifier is not automatically a drop-in replacement for the SY88843VMG. Compatibility depends on exact pin mapping, package geometry, exposed-pad requirements, input termination, differential gain, 3 dB bandwidth, output swing, jitter, and TTL shutdown polarity. Use the manufacturer cross-reference search or obtain a manufacturer-approved cross-reference before changing the PCB component.
When should I choose the SY88843VMG over a general-purpose amplifier?
Choose the SY88843VMG when the design needs a dedicated limiting stage for serial data up to 3.2 Gbps rather than a general-purpose analog amplifier. Its 38 dB differential gain, 2 GHz 3 dB bandwidth, 50-ohm CML outputs, and TTL shutdown are tailored to high-speed communication links. General-purpose amplifiers may provide lower gain, wider analog swing, or different output levels.
What are the key specifications of SY88843VMG that engineers should know?
The essential SY88843VMG specifications are 3.2 Gbps maximum data rate, 38 dB differential gain, a 2 GHz 3 dB bandwidth, 50-ohm CML outputs, 800 mVpp output swing, 60 ps edge rates, and a 3.3 V or 5 V supply. The device also provides TTL shutdown, 5 psRMS typical random jitter, and 15 psPP typical deterministic jitter in a 16-VFQFN exposed-pad package.

工程参考数据: SY88843VMG ——对比、设计指导和合规信息。

选型指南

Choose the SY88843VMG when a 3.3 V or 5 V serial link needs a dedicated limiting stage that supports rates to 3.2 Gbps and produces a 50-ohm CML output. It is a strong choice for optical-network, backplane, and chip-to-chip interfaces where attenuation requires restoration but the channel is already defined as a CML link. The 38 dB differential gain, 2 GHz 3 dB bandwidth, 800 mVpp swing, 60 ps edge rates, and TTL shutdown should match the link architecture before the footprint is approved.

Do not select a generic CML driver or a general-purpose differential amplifier solely from its speed rating. Those devices may not reproduce the combination of limiting behavior, gain, jitter, shutdown polarity, and exposed-pad thermal requirements. No drop-in alternative is confirmed here, so a substitution should be accepted only after its pin assignment, land pattern, input interface, output levels, bandwidth, jitter, and shutdown behavior are checked against the original design requirements.

与替代料对比

参数 本产品
Product Type Single limiting post amplifier
Brand Microchip Technology
Package 16-pin VFQFN with exposed pad, 3 mm x 3 mm
Supply Voltage 3.3 V or 5 V
Maximum Data Rate 3.2 Gbps
Differential Gain 38 dB
3 dB Bandwidth 2 GHz
Output Interface 50 ohm CML
Output Swing 800 mVpp
Shutdown TTL shutdown

关键差异点

  • Dedicated high-speed limiting function rather than general-purpose amplification (对比 CAT3626HV4-GT2)
  • Multi-rate operation with integrated TTL shutdown control (对比 General-purpose CML output drivers)
  • Compact 3 mm by 3 mm exposed-pad package for high-speed designs (对比 Larger leaded communication amplifiers)

设计说明

Route the differential inputs and 50-ohm CML outputs as controlled-impedance transmission lines with continuous return paths beneath the pair. Keep the traces short, avoid plane splits beneath the signal path, and minimize vias because discontinuities can create reflections that degrade the 60 ps edge rate. Place the device close to the receiving IC so that the amplifier compensates only the losses that must be corrected.

Connect the exposed pad to a low-impedance ground plane with short, wide vias and place the supply-decoupling capacitor immediately adjacent to the relevant supply pin. Use the 3.3 V or 5 V operating range specified by Microchip, and follow the recommended decoupling network and layout shown in the manufacturer datasheet. Poor return-current continuity beneath a high-speed differential pair can degrade jitter even when the amplifier operates within its specified voltage range.

Include the complete channel in the eye and jitter budget rather than evaluating only the amplifier's isolated 5 psRMS random-jitter figure. The 15 psPP typical deterministic jitter specification, connector loss, PCB loss, and any downstream device input jitter must be combined through an appropriate statistical or deterministic budget method. Confirm the 3.2 Gbps target against the measured channel loss at every supported data rate.

Do not substitute a general-purpose differential amplifier or a CML driver solely because its output levels appear similar. The SY88843VMG is a limiting post amplifier with a defined 38 dB gain, 2 GHz 3 dB bandwidth, 800 mVpp CML swing, 60 ps edge rates, and TTL shutdown function. Confirm the complete pin mapping and package land pattern, including the exposed pad, before approving any substitute.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The catalog information confirms a Microchip Technology communications IC but does not explicitly state RoHS, REACH, halogen-free, or conflict-minerals status. Confirm the applicable declarations on the current manufacturer product page before releasing a regulated design.

数据核验日期: 2026-11-20 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

SY88843VMG datasheet SY88843VMG pinout SY88843VMG datasheet pdf SY88843VMG equivalent SY88843VMG replacement SY88843VMG cross reference SY88843VMG price SY88843VMG stock Microchip SY88843VMG SY88843 3.2Gbps CML post amplifier SY88843 16 VFQFN footprint SY88843 optical network application

相关元器件 & 术语

Microchip Technology SY88843VMG SY88843VMG-TR limiting post amplifier high-speed amplifier signal-conditioning IC CML current-mode logic differential amplifier 3.2 Gbps 38 dB differential gain 2 GHz 3 dB bandwidth 800 mVpp output swing 60 ps edge rate random jitter deterministic jitter TTL shutdown 16-pin VFQFN exposed pad controlled-impedance routing optical networks backplane communication chip-to-chip serial link RoHS REACH
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情