T1014NSN7MQPA - QorIQ 1.2GHz 64-bit Power Arch MPU | NXP
料号： T1014NSN7MQPA ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $120.64 | $120.64 |
| 10 | $115.2 | $1,152.00 |
| 100 | $105.8 | $10,580.00 |
| 500 | $96.5 | $48,250.00 |
| 1,000 | $88.9 | $88,900.00 |
T1014NSN7MQPA 概述
A microprocessor (MPU) is a single-chip CPU containing the arithmetic logic unit, control unit, registers, cache, and memory management logic needed to execute operating systems and application workloads. Within the SoC hierarchy, an MPU integrates processor cores with on-chip peripherals (memory controllers, bus fabrics, accelerators, networking MACs), distinguishing it from a microcontroller (MCU) which typically targets control loops with on-chip flash. The T1 series occupies the networking/communications tier of NXP's QorIQ lineup, sitting below the multi-core T2/T4 layerscale parts and above the entry P-series.
Key features of the T1014NSN7MQPA include a single 64-bit Power Architecture e5500 core at 1.2 GHz, DPAA for packet parsing, classification, and crypto offload, integrated DDR3L/DDR4 controller with ECC, multiple PCIe Gen2 controllers, 1 Gbit Ethernet and 10 Gbit Ethernet MACs, and a deep-sleep low-power mode. Security is handled by the on-chip SEC engine, and the 780-FBGA package exposes the full T1 serial bus, including SerDes lanes for high-speed networking.
The DPAA architecture offloads buffer management, queueing, and cryptographic operations from the e5500 core, allowing line-rate packet processing at lower clock frequencies than software-only designs. Compared with general-purpose SoCs, the T1014NSN7MQPA offers deterministic I/O latency and hardware-accelerated networking, which is essential for router, switch, and security appliance workloads.
Typical applications include industrial routers, network switches, security gateways, factory automation controllers, and edge networking appliances. The 23x23 mm package footprint is shared across the T1 series, simplifying PCB layout reuse among T1013, T1014, T1023, and T1024 variants.
When designing with the T1014NSN7MQPA, allocate adequate PCB area for the 780-ball FBG BGA, plan thermal management for full-power operation, and verify DDR3L/DDR4 routing and impedance per the NXP hardware design guide. For higher core count or throughput, step up to the dual-core T1024 in the same package.
直接替换替代料： T1014NSN7MQPA ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
快速对比工具——选择替代料号进行并排对比：
T1024NSN7MQPA
✅ 直接替换📋 参考替代料（不在目录中）
T1023NSN7MQPA
✅ 直接替换📋 参考替代料（不在目录中）
T1013NSN7MQPA
✅ 直接替换📋 参考替代料（不在目录中）
T1014NSN7PQA
✅ 直接替换📋 参考替代料（不在目录中）
T1014NSE7MQPA
✅ 直接替换📋 参考替代料（不在目录中）
T1014NSN7MQPA 最大额定值与电气特性
| Family | QorIQ T1 |
| Core Architecture | PowerPC e5500, 64-bit |
| Number of Cores | 1 |
| Core Frequency | 1.2 GHz |
| 封装 | 780-FBGA (23x23 mm) |
| Memory Interface | DDR3L / DDR4 with ECC |
| Ethernet Interfaces | 1 GbE and 10 GbE MACs |
| PCIe | PCI Express Gen2 controllers |
| Hardware Acceleration | DPAA (Data Path Acceleration Architecture) |
| 工作温度 | 0 °C to +105 °C |
| Power Mode | Deep Sleep supported |
| 安装类型 | Surface Mount (BGA) |
| RoHS 状态 | Compliant |
| Lead-Free | Yes |
T1014NSN7MQPA 780-fbga (23x23 mm) 引脚配置指南
T1014NSN7MQPA（780-fbga (23x23 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： T1014NSN7MQPA.
请参阅 数据手册 以查看完整引脚配置。
典型应用
T1014NSN7MQPA 适用于 6 应用s: Industrial Router, Network Switch, Security Gateway / UTM Appliance, Edge Computing Appliance, Factory Automation Controller, Telecom Edge Equipment.
Industrial Router
The T1014NSN7MQPA's 1.2 GHz e5500 core and DPAA hardware acceleration deliver line-rate packet processing for industrial branch routers aggregating 1 GbE uplinks to 10 GbE backhaul. The integrated DDR3L/DDR4 controller with ECC provides the memory bandwidth and integrity required for routing tables, NAT, and VPN tunnels, while the 0-105 °C temperature grade supports factory-floor and outdoor cabinet deployment. Deep-sleep mode reduces idle power between active sessions without losing wake-on-LAN or OSPF keepalive state.
推荐
Network Switch
Managed Gigabit Ethernet switches use the T1014NSN7MQPA as a control-plane processor alongside external PHY and switch ASIC devices. The PCIe Gen2 controllers link to switch fabric chips, while the 1G/10G Ethernet MACs provide management, OOB, and stacking uplinks. DPAA accelerates ACL lookups and QoS classification, offloading the e5500 core so it can run routing protocols such as OSPF, BGP, or VXLAN control planes without saturating CPU cycles.
推荐
Security Gateway / UTM Appliance
Unified Threat Management appliances leverage the T1014NSN7MQPA's DPAA crypto and pattern-matching offload to deliver firewall, IPSec VPN, and deep-packet inspection at multi-Gbps rates. The integrated SEC engine accelerates AES, 3DES, SHA, and IPsec operations, while DDR4 with ECC ensures secure key material is protected from soft errors. The 780-FBGA package and 0-105 °C range suit 1U rackmount and fanless industrial appliance designs.
推荐
Edge Computing Appliance
Industrial edge gateways and SD-WAN edge nodes use the T1014NSN7MQPA to run containerized network functions at the network edge. The e5500 core and DPAA provide deterministic latency for NFV workloads, while PCIe lanes connect Wi-Fi 6, 5G modems, or NVMe storage. The wide temperature range and deep-sleep mode make it well suited to unmanned remote cabinets and outdoor PoE-powered installations.
推荐
Factory Automation Controller
Programmable Logic Controllers and industrial gateways using the T1014NSN7MQPA benefit from deterministic PCIe and Ethernet timing for PROFINET, EtherCAT, or EtherNet/IP masters. The 0-105 °C range tolerates factory-floor heat, while the e5500 core runs real-time Linux or VxWorks with predictable interrupt latency. DPAA offloads industrial protocol parsing, freeing the core for PLC logic and SCADA communications.
推荐
Telecom Edge Equipment
Small-cell, baseband, and access aggregation equipment use the T1014NSN7MQPA for control-plane processing of LTE/5G small-cell traffic. The integrated 10 GbE MACs support fronthaul or midhaul links to centralized baseband units, while DPAA accelerates GTP-U, PFCP, and IPSec tunneling. Extended temperature and long-life NXP supply make it suitable for carrier-grade deployments requiring multi-year availability.
推荐
推荐产品汇总
工程参考数据： T1014NSN7MQPA ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | T1024NSN7MQPA | T1023NSN7MQPA | T1013NSN7MQPA | T1014NSN7PQA |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 780-FBGA (23x23) | 780-FBGA (23x23) | 780-FBGA (23x23) | 780-FBGA (23x23) | 780-FBGA (23x23) |
| Cores | 1 | 2 | 2 | 1 | 1 |
| Memory Interface | DDR3L/DDR4 ECC | DDR3L/DDR4 ECC | DDR3L/DDR4 ECC | DDR3L/DDR4 ECC | DDR3L/DDR4 ECC |
| 10 GbE | Yes | Yes | Yes | Yes | Yes |
| DPAA | Yes | Yes | Yes | Yes (reduced) | Yes |
| Operating Temperature | 0 to +105 °C | 0 to +105 °C | 0 to +105 °C | 0 to +105 °C | 0 to +105 °C |
关键差异点
- Single-core 1.2 GHz with DPAA at lower cost than dual-core T1024 （对比 T1024NSN7MQPA)
- Pinout-compatible with T1 family for PCB reuse （对比 T1013NSN7MQPA)
- Industrial 0-105 °C temperature grade with deep-sleep （对比 T1024NSN7MQPA)
设计说明
The 780-FBGA package dissipates significant power at 1.2 GHz under full DPAA load. Estimate 5-9 W typical and 12+ W peak; provide a thermal pad interface to a heat spreader or copper heat sink. For fanless industrial enclosures, derate ambient temperature by 10-15 °C below the 105 °C Tj ceiling and validate with a thermal probe on the top-side center of the BGA.
Use a minimum 12-layer PCB stackup with dedicated ground and power planes adjacent to the BGA breakout layers. Matched-impedance routing for DDR3L/DDR4 (single-ended 50 ohm, differential 100 ohm) and SerDes (100 ohm differential) is mandatory. Refer to the NXP QorIQ T1 hardware design guide for via-in-pad, microvia, and BGA escape recommendations to avoid signal-integrity issues at 1.2 GHz core clocks and 10 GbE SerDes rates.
Do not power the T1014NSN7MQPA without all supply rails (Vcore, VDD, SerDes, DDR, GPIO) ramped in the correct sequence per the datasheet. Failure to sequence can latch-up or damage the BGA. Always populate the JTAG header for first-bring-up debug, and verify DDR4 training succeeds across the full 0 to 105 °C range before committing to the design.
10 GbE and PCIe Gen2 SerDes require careful length matching within 0.1 mm tolerance and continuous reference planes. Avoid routing SerDes across plane splits or stitching vias can introduce impedance discontinuities. Use the IBIS-AMI models from NXP for channel simulation before fab.
Estimated: at VIN 12 V, Vcore ~1.0 V at 1.2 GHz with 6 W core power, the DC-DC converter must deliver at least 8 A continuous with 12 A surge capability for DPAA bursts. Use a multiphase PWM controller with adaptive voltage positioning to reduce bulk-capacitor requirements and improve transient response.
合规信息
RoHS and lead-free per NXP product page. Not AEC-Q100 - QorIQ T1 targets industrial/telecom, not automotive. REACH and conflict-minerals compliance inferred from NXP standard policy.
