XC2C128-6TQ144C - 128-Macrocell 1.8V CPLD | Xilinx
料号: XC2C128-6TQ144C ✗ 停产XC2C128-6TQ144C 概述
A complex programmable logic device, or CPLD, is a user-programmable semiconductor that combines multiple programmable logic arrays with a fixed interconnect structure. Within the broader hierarchy, a CPLD is a programmable-logic IC, a member of the FPGA and CPLD category, and an alternative to a small field-programmable gate array. The CoolRunner-II architecture is intended for deterministic signal routing, interface adaptation, control logic, and designs requiring rapid configuration without an external configuration memory.
The XC2C128-6TQ144C provides 128 macrocells, 100 I/O pins, eight logic array blocks, and approximately 3,000 gates. Its stated propagation delay is 5.7 ns, while the -6 suffix identifies the device's speed grade. The low-power design targets 1.8 V systems and is reported to support quiescent current as low as 13 uA. The commercial-temperature variant operates from 0 C to 70 C according to the indexed product specifications.
The device uses 0.18-micron CMOS technology and supports in-system programmability, allowing a board designer to configure the logic after soldering. Its fixed interconnect architecture supports repeatable routing and compact implementation of glue logic. Signal-path design should still account for setup and hold requirements, output loading, input thresholds, and the propagation delay of the selected logic implementation rather than treating the headline 5.7 ns figure as a complete timing guarantee.
Typical uses include industrial control, communications equipment, consumer interfaces, battery-operated products, and embedded control systems where the logic density must fit within a moderate package. A designer can use the XC2C128-6TQ144C for bridge functions, protocol conversion, state-machine control, data-routing logic, or startup sequencing. It is particularly useful where nonvolatile configuration, low quiescent power, and a compact 144-pin surface-mount package are more important than very high logic density.
PCB implementation should provide a stable 1.8 V supply, short return paths, and decoupling close to the power pins. Confirm the exact pin assignments and power requirements against the manufacturer datasheet before assigning board functions. Because the TQFP package has fine-pitch leads, inspect solder joints for bridging and confirm the board's exposed thermal and ground geometry during assembly.
This product page combines device specifications, package information, practical implementation guidance, and drop-in CoolRunner-II alternatives. It also identifies the timing, temperature, and supply distinctions that matter when comparing speed grades or planning a board revision without changing the existing 144-lead footprint.
直接替换替代料: XC2C128-6TQ144C ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: XC2C128-6TQ144C (相同外形与封装尺寸) ——差异在于 Device Type, Process Technology, Operating Temperature, Package, Quiescent Current.
XC2C128-7TQ144C
✅ 直接替换联系询价
查看数据手册 →XC2C128-7TQ144I
✅ 直接替换联系询价
查看数据手册 →XC2C128-7TQG144C
✅ 直接替换📋 参考替代料(不在目录中)
XC2C128-5TQ144C
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
XC2C128-4TQ144C
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
XC2C128-6TQ144C 最大额定值与电气特性
| Device Type | CoolRunner-II complex programmable logic device |
| Macrocell Count | 128 macrocells |
| Logic Gate Count | Approximately 3000 gates |
| Logic Array Blocks | 8 logic array blocks |
| Maximum User I/O | 100 I/O pins |
| Propagation Delay | 5.7 ns |
| Internal Supply Voltage | 1.7 V to 1.9 V |
| Nominal Operating Supply | 1.8 V |
| 静态电流 | As low as 13 uA |
| Process Technology | 0.18-micron CMOS |
| Programmability | Nonvolatile in-system programmable |
| 封装 | 144-lead TQFP, 14 mm x 14 mm, 0.5 mm pitch |
| Terminal Count | 144 terminals |
| 安装类型 | Surface mount |
| 工作温度 | 0 C to 70 C |
| Logic Family | CMOS |
| Timing Grade | Speed grade -6 |
XC2C128-6TQ144C 144-lead tqfp, 14 mm x 14 mm, 0.5 mm pitch 引脚配置指南
XC2C128-6TQ144C(144-lead tqfp, 14 mm x 14 mm, 0.5 mm pitch 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: XC2C128-6TQ144C.
请参阅 数据手册 以查看完整引脚配置。
典型应用
XC2C128-6TQ144C 适用于 6 应用s: Industrial Control and Automation, Communications Interface Bridging, Battery-Operated Embedded Products, Consumer Equipment Interface Logic, Data Routing and Glue Logic, Programmable Test and Measurement Logic.
Industrial Control and Automation
The XC2C128-6TQ144C fits compact industrial control logic where deterministic routing, 128 macrocells, and 100 I/O pins are useful without requiring a larger FPGA. Its 5.7 ns propagation delay can support tightly registered control paths, while the 1.7 V to 1.9 V internal supply range aligns with 1.8 V system rails. The nonvolatile in-system programmable architecture also simplifies field updates. The commercial-grade part is appropriate for ambient conditions from 0 C to 70 C; wider environmental requirements call for a temperature-qualified ordering option.
推荐
Communications Interface Bridging
The XC2C128-6TQ144C can implement protocol conversion, framing, and data-routing logic between mixed communication interfaces. Its 100 I/O pins provide substantial connectivity for parallel and control signals, while the 5.7 ns propagation delay supports short combinational paths. The CoolRunner-II architecture preserves routing predictability, which is valuable when repeating a board across multiple communications products. Validate signal timing against the external transceiver and account for package and board delays rather than relying only on the internal device specification.
推荐
Battery-Operated Embedded Products
The XC2C128-6TQ144C is appropriate for low-power embedded products that need reconfigurable control logic but cannot tolerate the complexity of an FPGA design flow. Quiescent current is reported as low as 13 uA, while the 0.18-micron CMOS implementation targets efficient 1.8 V operation. Nonvolatile configuration allows the logic to operate immediately without a boot loader. For battery designs, evaluate sleep-state current, active-state I/O loading, and regulator quiescent current across the complete operating profile.
推荐
Consumer Equipment Interface Logic
The XC2C128-6TQ144C can consolidate button decoding, display sequencing, peripheral selection, and status-control logic in consumer equipment. Its 128 macrocells provide enough capacity for several control functions, and the 100 I/O pins simplify connections to external sensors and display interfaces. The 5.7 ns speed class helps preserve timing margin in short control paths. Use the manufacturer's I/O standard and timing tables when connecting the device to slower consumer peripherals or proprietary buses.
推荐
Data Routing and Glue Logic
The XC2C128-6TQ144C is well suited to deterministic data routing, address decoding, bus arbitration, and state-machine control in systems built around multiple processors or converters. Its eight logic array blocks and 128 macrocells offer more capacity than simple fixed-function glue logic, while the fixed interconnect supports repeatable implementation. The 5.7 ns propagation delay provides a clear timing class for preliminary architecture work. Complete sign-off requires checking every external path with the appropriate timing constraints and I/O assumptions.
推荐
Programmable Test and Measurement Logic
The XC2C128-6TQ144C can implement configurable test sequences, pattern generation, acquisition control, and timing-envelope logic in compact measurement equipment. Its 100 I/O pins allow multiple instrument controls and monitored channels to share a programmable fabric, while the 5.7 ns device speed supports short control paths. In-system programmability allows different test configurations to be loaded into the same board. Keep analog, high-voltage, and high-speed instrumentation interfaces outside the CPLD and use suitable buffers or protection components.
推荐
推荐产品汇总
工程参考数据: XC2C128-6TQ144C ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | XC2C128-7TQ144C | XC2C128-7TQ144I | XC2C128-7TQG144C | XC2C128-5TQ144C | XC2C128-4TQ144C |
|---|---|---|---|---|---|---|
| Brand | Xilinx | Xilinx | Xilinx | Xilinx | Xilinx | Xilinx |
| Package | TQFP-144 | TQFP-144 - same | TQFP-144 - same | TQFP-144 - same | TQFP-144 - same | TQFP-144 - same |
| Device Type | CoolRunner-II CPLD | CoolRunner-II CPLD | CoolRunner-II CPLD | CoolRunner-II CPLD | CoolRunner-II CPLD | CoolRunner-II CPLD |
| Macrocell Count | 128 macrocells | 128 macrocells | 128 macrocells | 128 macrocells | 128 macrocells | 128 macrocells |
| Propagation Delay | 5.7 ns | 7 ns | 7 ns | 7 ns | 5 ns | 4 ns |
关键差异点
- Faster -6 timing grade in the same 144-lead footprint (对比 XC2C128-7TQ144C)
- Commercial-temperature option for general-purpose designs (对比 XC2C128-7TQ144I)
- Balanced speed choice for designs with constrained board revision (对比 XC2C128-4TQ144C)
- Documented 100-pin user I/O capacity (对比 XC2C128-7TQ144C)
设计说明
Design the XC2C128-6TQ144C around its 1.8 V internal architecture and use the manufacturer power-connection table to identify every supply pin. Place the required bypass capacitors directly beside the associated power and ground terminals, with short, low-impedance return paths. Do not assume that a quiet 1.8 V rail is sufficient for every configuration or I/O condition; check output-current limits, input thresholds, and state-dependent current in the device timing and power documentation.
The 144-lead TQFP uses a 0.5 mm lead pitch on a 14 mm by 14 mm body. Use the manufacturer land pattern for the PCB footprint, maintain the specified pad and solder-mask geometry, and avoid placing tall components that interfere with the leads. After assembly, inspect the fine-pitch rows under magnification because solder bridges can create intermittent faults between adjacent I/O or power pins.
Do not treat the 5.7 ns propagation-delay headline as complete timing sign-off. Apply the manufacturer timing tables to the actual macrocell path, register boundaries, I/O standard, external load, and board delay. Also confirm the exact configuration mode, startup behavior, and temperature ordering code for the selected XC2C128 variant. A mechanically similar speed-grade substitute can have a different acceptable operating range even when its footprint is unchanged.
For high-speed or lightly loaded board routes, keep the CPLD close to the associated connector or memory device and minimize stubs on sensitive nets. Apply the published I/O drive-strength and loading limits to the selected bank configuration. For mixed-voltage interfaces, use level translation where the device's I/O tolerance does not cover the external voltage. Review ground-reference continuity beneath the package because a fragmented plane can degrade return paths despite a correct schematic.
合规信息
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated for this exact ordering code. The CMOS process technology and commercial operating range are documented, but they do not establish regulatory compliance.