XC2C384-7FT256C - 384-Macrocell 7.1ns CPLD | AMD Xilinx
料号: XC2C384-7FT256C ✗ 停产XC2C384-7FT256C 概述
A complex programmable logic device, or CPLD, is a programmable-logic semiconductor that belongs to the FPGA and CPLD category of programmable logic devices. Unlike a soft processor or fixed-function controller, a CPLD implements digital logic through user-programmed interconnect and macrocell resources. The CoolRunner-II architecture combines logic macrocells, programmable routing, and dedicated memory resources so control, decode, interface, and glue-logic functions can be consolidated into one device.
The XC2C384 provides 384 macrocells, approximately 9,000 logic gates, and a maximum characterized system frequency of 217 MHz for the specified resettable-counter test. Its -7 speed grade is described by a 7.1 ns pin-to-pin delay. The 0.18-micron CMOS implementation is optimized for 1.8 V systems, while the device is identified as offering low quiescent current, with a listed minimum value of 14 A in the component specification summary.
Programmable output features include slew-rate limiting, bus hold, pull-up, open-drain, and programmable-ground options. Inputs can use selectable Schmitt-trigger behavior on a per-pin basis, which helps improve noise tolerance in slower or less controlled external environments. Macrocell registers may also be configured as direct input registers, allowing selected external signals to be captured without using the normal combinational macrocell path.
The XC2C384-7FT256C is suitable for industrial control, communications-interface, peripheral bridging, data-capture, and general-purpose embedded-logic designs. Its 240 user I/O pins provide substantial board-level connectivity, while the 256-ball FTFBGA package supports compact, high-pin-count implementations. Designers should base final frequency and power claims on timing analysis of the implemented design rather than the device-level maximum alone.
For PCB implementation, follow the manufacturer ball map and recommended power, decoupling, and routing guidance exactly. Confirm the selected configuration file, pin assignments, I/O standards, voltage tolerances, and bank power requirements before release. The 7.1 ns speed grade can improve timing margin, but the complete design must still be analyzed for logic depth, routing congestion, and external component timing.
This product summary combines the verified device characteristics, package and timing references, pricing availability, drop-in replacement findings, and practical implementation guidance. It highlights where the -7 grade differs from slower CoolRunner-II configurations and helps engineers distinguish a genuine PCB-compatible replacement from a merely similar CPLD.
直接替换替代料: XC2C384-7FT256C ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
XC2C384-10FT256C
✅ 直接替换📋 参考替代料(不在目录中)
XC2C384-7FTG256C
✅ 直接替换📋 参考替代料(不在目录中)
XC2C384-10FTG256C
✅ 直接替换📋 参考替代料(不在目录中)
XC2C384-7FT256C 最大额定值与电气特性
| Device Type | CoolRunner-II complex programmable logic device |
| Macro Cells | 384 macrocells |
| Logic Gates | 9,000 gates |
| Maximum Frequency | 217 MHz |
| Pin-to-Pin Propagation Delay | 7.1 ns |
| 电源电压 | 1.8 V |
| Technology | 0.18 um CMOS |
| User I/O Pins | 240 pins |
| Total Package Pins | 324 pins |
| 封装 | FTFBGA-324, 23 x 23 mm, 1 mm pitch |
| Logic Family | CMOS |
| 工作温度 | 0 C to 70 C |
| 静态电流 | 14 A minimum |
| 输出配置 | Slew-rate limit, bus hold, pull-up, open drain, and programmable ground |
| Input Configuration | Schmitt-trigger input available per input pin |
| Architecture | Optimized for 1.8 V systems |
XC2C384-7FT256C ftfbga-324, 23 x 23 mm, 1 mm pitch 引脚配置指南
XC2C384-7FT256C(ftfbga-324, 23 x 23 mm, 1 mm pitch 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: XC2C384-7FT256C.
请参阅 数据手册 以查看完整引脚配置。
典型应用
XC2C384-7FT256C 适用于 6 应用s: Industrial Control and Logic Consolidation, Communications Interface and Protocol Bridging, Data Capture and Signal Conditioning, Peripheral Bridging and Glue Logic, Embedded RAM and Lookup Logic, Compact High-Density Control Platform.
Industrial Control and Logic Consolidation
The XC2C384-7FT256C fits industrial controllers that combine machine-control decoding, sensor gating, actuator sequencing, and communications formatting in one programmable device. Its 384 macrocells and approximately 9,000 logic gates provide substantial capacity for parallel control logic, while 240 user I/O pins reduce the need for external glue devices. The listed 0 C to 70 C commercial-temperature range suits equipment whose internal ambient remains within that interval. The 7.1 ns pin-to-pin delay can improve margin in synchronized control paths, although the final implementation still requires static timing analysis. Use the manufacturer ball map to assign control and field-connection pins, and confirm isolation, protection, grounding, and surge requirements at the board boundary rather than relying on the CPLD alone.
推荐
Communications Interface and Protocol Bridging
The XC2C384-7FT256C is appropriate for fixed-format communications bridges, status-word translators, and legacy peripheral interfaces where parallel logic is more practical than programmable processor firmware. Its 240 user I/O pins can support multiple data groups, control signals, and clock-domain crossing functions, while the 7.1 ns delay provides a useful timing margin for registered interface logic. Programmable pull-up, bus-hold, slew-rate, and open-drain options help support practical board-level signaling. Designers should use the device timing report to evaluate every external setup and hold requirement. The 1.8 V operating point also requires careful review of transceiver voltage levels, series termination, and ground-return paths so that the CPLD cannot be exposed to signals outside its specified I/O limits.
推荐
Data Capture and Signal Conditioning
XC2C384-7FT256C can implement parallel data capture, pulse qualification, event sequencing, and programmable input conditioning where deterministic nonvolatile logic is preferred. Selectable Schmitt-trigger inputs are useful for external thresholds or noisy transitions, and the macrocell output options permit controlled slew rates, pull-ups, bus hold, and open-drain behavior. The -7 grade's listed 7.1 ns pin-to-pin delay can help preserve margin when samples are registered on a system clock. Validate capture timing against the source device's output delay and board skew, because the device maximum does not include every external path. Keep input and output standards within their respective voltage limits, and use the manufacturer's pin constraints and IOB timing information when assigning state logic and clocked registers in the design tool.
推荐
Peripheral Bridging and Glue Logic
The XC2C384-7FT256C fits legacy peripheral bridging tasks involving address decode, data-width conversion, interrupt coordination, FIFO-like control, and asynchronous status translation. Its 9,000-gate and 384-macrocell resources allow multiple interface blocks to coexist without relying on a separate FPGA, and the nonvolatile programmable architecture supports stable logic immediately after power-up. The listed 217 MHz test frequency describes a characterized resettable-counter case rather than every possible design, so actual clock targets depend on routing and macrocell utilization. Assign inputs directly to macrocell registers when capture behavior is required, and use constrained source clocks to prevent the implementation from relying on ideal timing assumptions. Review external transceiver direction, level translation, and bus contention before finalizing the board connection.
推荐
Embedded RAM and Lookup Logic
XC2C384-7FT256C supports designs that combine programmable control logic with embedded static RAM for tables, counters, status histories, and small data buffers. The 384-macrocell resource count allows RAM blocks and surrounding address, enable, and output logic to be placed in one programmable device, reducing board area compared with separate logic and memory packages. The 0.18-micron CMOS architecture is optimized for 1.8 V systems, and the -7 grade offers a listed 7.1 ns pin-to-pin delay for registered memory-access paths. Timing closure still depends on the implemented address decode and output pipeline. Use synchronous design practices where possible, constrain all relevant clocks, and inspect the final timing report for memory-access setup, hold, clock-to-out, and routing margin before programming production hardware.
推荐
Compact High-Density Control Platform
The 256-user-I/O FTFBGA package makes XC2C384-7FT256C useful in dense control platforms where connector count, routing congestion, and board area are primary constraints. The 23 x 23 mm, 1 mm-pitch package places 324 total balls in a compact land pattern and provides 240 user I/O pins for sensors, actuators, high-speed control buses, and local status lines. Its commercial 0 C to 70 C temperature range and 1.8 V supply fit many enclosed industrial and communications platforms, provided thermal and signal-integrity requirements are satisfied. High-density BGA assembly demands disciplined escape routing, layer transitions, and power-plane continuity. Follow the manufacturer package and board-layout guidance, verify all ball assignments against the exact device pinout, and complete assembly-process qualification before volume manufacture.
推荐
推荐产品汇总
工程参考数据: XC2C384-7FT256C ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | XC2C384-10FT256C | XC2C384-7FTG256C | XC2C384-10FTG256C |
|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD |
| Package | FT256 | FT256 - same | FT256 - same | FT256 - same |
| Macro Cells | 384 macrocells | 384 macrocells | 384 macrocells | 384 macrocells |
| Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Technology | 0.18 um CMOS | 0.18 um CMOS | 0.18 um CMOS | 0.18 um CMOS |
| Product Family | CoolRunner-II | CoolRunner-II | CoolRunner-II | CoolRunner-II |
关键差异点
- Faster -7 speed grade (对比 XC2C384-10FT256C)
- Direct 256-user-I/O package capacity (对比 XC2C384-7TQ144C)
- High logic density in a compact BGA (对比 XC2C256-7FT256C)
设计说明
Treat the XC2C384-7FT256C as a 324-ball BGA assembly, not as a generic 256-pin peripheral. Route power, ground, configuration, and user-I/O escape paths using the exact manufacturer ball map and recommended land pattern. Preserve uninterrupted ground references beneath signal escapes, minimize return-path discontinuities, and qualify the assembly process for the 1 mm pitch. Do not assign PCB functions from the 240-user-I/O count alone; many balls serve power, ground, configuration, or dedicated functions.
A -10 speed-grade device is not automatically equivalent to the -7 XC2C384-7FT256C. The listed pin-to-pin delay rises from 7.1 ns to 9.2 ns, a difference of approximately 2.1 ns, so critical paths may lose timing margin after substitution. Preserve the original part where timing closure is tight. If a -10 device must be evaluated, regenerate the timing report, compare every clock-domain constraint, and confirm that external setup and hold requirements still pass.
The device operates from a 1.8 V supply and has a listed minimum quiescent current of 14 A, but real board consumption also includes configuration and dynamic activity. Follow the manufacturer power-decoupling topology and place the required bypass capacitors directly at the associated supply balls. Check startup sequencing, rail ramp limits, I/O voltage relationships, and total supply-current margin. Use the device-specific power estimator with actual I/O loading and activity assumptions rather than relying only on quiescent current.
Use the configurable input and output features only after confirming their electrical limits. Per-pin Schmitt-trigger selection can improve transition tolerance, while slew-rate control, pull-up, open-drain, and bus-hold options can support particular interface requirements. These features do not replace correct external termination or level translation. Analyze each high-speed interface for rise and fall time, ringing, setup, hold, contention, and signal-return continuity, and verify the completed design against the manufacturer timing and I/O specifications.
合规信息
No explicit compliance declarations were identified for this exact MPN. The commercial 0 C to 70 C operating range does not by itself establish AEC-Q100 qualification.