المنتجات (44,000+)

TRS3221EIRGTR - 3-5.5V RS-232 Transceiver, 250kbps, ±15kV ESD | Texas Instruments
TRS3221EIRGTR

TRS3221EIRGTR - 3-5.5V RS-232 Transceiver, 250kbps, ±15kV ESD | Texas Instruments

The Texas Instruments TRS3221EIRGTR is a 3- to 5.5-V single-channel RS-232 line driver/receiver delivering 250 kbps data rate with ±15 kV IEC-ESD protection in a 16-pin VQFN (RGT) package measuring 3x3 mm with an exposed thermal pad. The device integrates one driver and one receiver, supports VCC operation from 3.0 V to 5.5 V (compatible with TTL/CMOS logic levels), and meets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standards. An RS-232 transceiver is a charge-pump-based interface IC that translates between TTL/CMOS logic levels (0-3.3 V or 0-5 V) and the ±5 V to ±15 V swing required by the legacy TIA/EIA-232-F serial communication standard. RS-232 transceivers belong to the broader interface IC family, which sits hierarchically between discrete level-shifters and protocol controllers (UARTs) in wired communication systems. RS-232 remains widely deployed in industrial equipment, point-of-sale terminals, medical instruments, and embedded debug ports where simplicity, point-to-point connectivity, and proven robustness outweigh the bandwidth advantages of USB or Ethernet. Key features include ±15 kV Human-Body Model (HBM) ESD protection on RS-232 pins, ±8 kV IEC 61000-4-2 contact discharge, ±15 kV IEC 61000-4-2 air-gap discharge, and an automatic powerdown feature that disables drivers when no valid RS-232 cable is detected. The on-chip dual charge pump requires only four external 0.1 µF capacitors, enabling true 5 V operation from a single 3.3 V supply without a separate ±12 V rail. The 250 kbps data rate is adequate for all standard RS-232 baud rates up to and beyond 115200 with margin to spare. The architecture combines a regulated switched-capacitor voltage doubler/inverter with a proprietary low-dropout RS-232 driver stage and a precision hysteresis receiver. ESD protection is implemented at the cable-side pins using TI's integrated silicon-controlled-rectifier (SCR) clamps. The 16-pin VQFN package's exposed pad provides a low thermal resistance path, which is useful when the part operates near the upper end of its 1 mA quiescent current budget in warm enclosures. Typical applications include industrial PLC programming ports, point-of-sale (POS) terminals, medical device serial consoles, battery-powered handhelds, and embedded debug UARTs that need robust ESD performance in the field. The TRS3221EIRGTR's small 3x3 mm footprint suits space-constrained designs such as USB-to-serial dongles, IoT gateways, and barcode scanners. When designing with this part, place the four charge-pump capacitors as close as possible to the C1+ / C1- / C2+ / C2- pins and keep the RS-232 trace lengths short to maximize ESD margin. Note that the TRSF3221E is the higher-speed (1 Mbit/s) pin-compatible alternative if 250 kbps is insufficient. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا
TRSF3222CPW - 3V-5.5V RS-232 Transceiver, 2/2 Drivers | TI TSSOP-20
TRSF3222CPW

TRSF3222CPW - 3V-5.5V RS-232 Transceiver, 2/2 Drivers | TI TSSOP-20

The Texas Instruments TRSF3222CPW is a 2-driver/2-receiver RS-232 line transceiver that operates from a single 3.0V to 5.5V supply in a 20-pin TSSOP package. It supports data rates up to 1 Mbit/s and accepts 5-V logic inputs when powered from a 3.3V rail, making it ideal for mixed-voltage system designs. A line transceiver is an interface device that bridges a logic-level UART (universal asynchronous receiver/transmitter) on a host microcontroller with the RS-232 standard, which swings between +12V and -12V on the bus side. It sits within the Interface IC hierarchy (RS-232 transceiver -> line transceiver -> interface IC -> integrated circuit) and converts TTL/CMOS logic levels to TIA/EIA-232-F compliant voltage levels while protecting the host from ESD events on the cable side. The TRSF3222CPW integrates a dual charge-pump that generates the required +5.5V and -5.5V rails from a single 3.3V supply using four small 0.1 uF external capacitors. Standby current is typically 1 uA, supporting low-power portable designs. The receivers remain active in shutdown, allowing wake-up characters to be detected without waking the host. ESD protection exceeds +/-15 kV HBM on the bus pins. Typical applications include industrial point-of-sale terminals, factory automation equipment, portable diagnostic instruments, and battery-powered barcode scanners where 3.3V logic must communicate with legacy RS-232 peripherals. The wide 3.0V-5.5V supply range also makes the part suitable for USB-to-serial bridges and embedded computing modules. When designing with this device, place the four charge-pump capacitors as close to the IC as possible to minimize loop inductance. The TSSOP-20 footprint requires standard surface-mount assembly with a maximum reflow temperature per JEDEC J-STD-020. Decouple VCC with a 0.1 uF ceramic plus a bulk tantalum if the supply impedance is high.

طلب عرض سعر اتصل بنا
TS3022ID - Dual High-Speed Rail-to-Rail Comparator | STMicroelectronics
TS3022ID

TS3022ID - Dual High-Speed Rail-to-Rail Comparator | STMicroelectronics

The STMicroelectronics TS3022ID is a dual high-speed comparator with rail-to-rail input stages, push-pull outputs, and operation from 2 V to 5 V supply voltage. The device is specified for a wide -40 °C to +125 °C temperature range and is packaged in an 8-SOIC package. Each comparator channel provides independent inputs and a push-pull output, making the TS3022ID suitable for dual-threshold, window-detection, line-driver, and signal-conditioning applications. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. The TS3022 belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where its low supply-voltage operation and rail-to-rail inputs help simplify designs operating from 2 V to 5 V rails. Rail-to-rail input behavior is especially useful when the signal range approaches either supply rail, while the high-speed response supports applications requiring rapid threshold decisions. The TS3022ID is identified as a general-purpose dual comparator with push-pull outputs. Its specified supply range is 2 V to 5 V, and the datasheet describes a high-speed response time. The TS3022 family is designed for micropower operation, with supply consumption described as being as low as a few tens of microamperes. The operating temperature range of -40 °C to +125 °C supports use across industrial, automotive, and consumer temperature conditions when the surrounding system satisfies the device's electrical requirements. The rail-to-rail input architecture allows sensing of signals close to the positive or negative supply rails. This can reduce the need for artificial input biasing in low-voltage systems, although input common-mode behavior, output timing, and supply decoupling still require careful validation in the final application. Because the device contains two comparators, applications can use the two channels for independent decisions or for upper and lower thresholds that define a monitoring window. Typical uses include battery-voltage threshold detection, overvoltage and undervoltage indication, signal crossing detection, pulse-width qualification, sensor-level conditioning, and fast logic-level generation. The 8-SOIC package is also convenient for prototypes and through-hole assembly. For battery-powered equipment, the low operating voltage and micropower characteristics can help reduce system energy use, provided the input signals remain within the specified common-mode range. Designers should place supply bypass capacitance close to the device and use the pin descriptions in the manufacturer datasheet when assigning PCB tracks. Input filtering may be required when noisy signals are compared because propagation delay and input offset can cause repeated output transitions. The TS3022ID is therefore most appropriate when a designer needs two fast, low-voltage, rail-to-rail comparator channels in a conventional SOIC footprint.

طلب عرض سعر اتصل بنا
TS321ID - Single 30 V 800 kHz Op Amp | Texas Instruments
TS321ID

TS321ID - Single 30 V 800 kHz Op Amp | Texas Instruments

Texas Instruments TS321ID is a single bipolar operational amplifier rated for 30 V operation, an 800 kHz gain-bandwidth product, and an 8-pin SOIC package. It is intended for cost-sensitive applications where space savings matter, making it a compact general-purpose amplifier for industrial, instrumentation, and signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The TS321 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Its basic amplifier functions include voltage amplification, buffering, filtering, summing, and feedback-based control, provided the external feedback network and operating limits are respected. The verified product information identifies a single amplifier circuit, a 30 V maximum operating framework, 800 kHz bandwidth, general-purpose classification, and an 8-pin SOIC package. The bipolar architecture and low-power positioning suit cost-sensitive designs, while the SOIC footprint supports conventional surface-mount assembly. Exact offset, bias-current, noise, slew-rate, common-mode, and output-swing values require confirmation in the manufacturer datasheet before final circuit sign-off. TS321ID is useful as a general-purpose amplifier in low- and moderate-bandwidth analog paths. Its verified 800 kHz bandwidth makes it relevant to signal conditioning where the required closed-loop bandwidth is well below that level. The single-amplifier configuration can simplify designs that need one amplifier rather than a dual package, particularly in sensor interfaces, control loops, audio preamplification, and industrial measurement circuits. The principal design consideration is preserving signal headroom and stability. An 8-pin SOIC package requires adequate PCB spacing, controlled grounding, and decoupling close to the power pins. Feedback resistors, compensation components, and input or output loading determine the actual usable bandwidth and must be evaluated against the application. Because verified operating details beyond the supplied values are incomplete, engineers should consult the TS321 manufacturer datasheet before choosing component values. This page combines verified manufacturer and distributor information, structured technical context, sourcing guidance, and engineering notes. It also clearly identifies unavailable electrical parameters rather than presenting guessed values, helping engineers move from part selection to a validated TS321ID design with fewer sourcing and specification ambiguities.

طلب عرض سعر اتصل بنا
TS321IDR - Single 30 V 800 kHz Op Amp | Texas Instruments (Tape & Reel)
TS321IDR

TS321IDR - Single 30 V 800 kHz Op Amp | Texas Instruments (Tape & Reel)

Texas Instruments TS321IDR is a single bipolar operational amplifier rated for 30 V operation, an 800 kHz gain-bandwidth product, and an 8-pin SOIC package. It is intended for cost-sensitive applications where space savings matter, making it a compact general-purpose amplifier for industrial, instrumentation, and signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The TS321 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Its basic amplifier functions include voltage amplification, buffering, filtering, summing, and feedback-based control, provided the external feedback network and operating limits are respected. The verified product information identifies a single amplifier circuit, a 30 V maximum operating framework, 800 kHz bandwidth, general-purpose classification, and an 8-pin SOIC package. The bipolar architecture and low-power positioning suit cost-sensitive designs, while the SOIC footprint supports conventional surface-mount assembly. Exact offset, bias-current, noise, slew-rate, common-mode, and output-swing values require confirmation in the manufacturer datasheet before final circuit sign-off. TS321IDR is useful as a general-purpose amplifier in low- and moderate-bandwidth analog paths. Its verified 800 kHz bandwidth makes it relevant to signal conditioning where the required closed-loop bandwidth is well below that level. The single-amplifier configuration can simplify designs that need one amplifier rather than a dual package, particularly in sensor interfaces, control loops, audio preamplification, and industrial measurement circuits. The principal design consideration is preserving signal headroom and stability. An 8-pin SOIC package requires adequate PCB spacing, controlled grounding, and decoupling close to the power pins. Feedback resistors, compensation components, and input or output loading determine the actual usable bandwidth and must be evaluated against the application. Because verified operating details beyond the supplied values are incomplete, engineers should consult the TS321 manufacturer datasheet before choosing component values. This page combines verified manufacturer and distributor information, structured technical context, sourcing guidance, and engineering notes. It also clearly identifies unavailable electrical parameters rather than presenting guessed values, helping engineers move from part selection to a validated TS321IDR design with fewer sourcing and specification ambiguities.

طلب عرض سعر اتصل بنا
TS321IDT - 30V Single 800kHz Op Amp | STMicroelectronics
TS321IDT

TS321IDT - 30V Single 800kHz Op Amp | STMicroelectronics

The STMicroelectronics TS321IDT is a single bipolar operational amplifier with an 800 kHz gain-bandwidth product, a 30 V total supply rating, and an 8-pin SOIC package. Designed for cost-sensitive applications where space efficiency matters, the TS321IDT provides a practical general-purpose amplification stage for industrial control, instrumentation, sensor interfaces, and low-frequency signal-conditioning circuits. An operational amplifier is an active analog component that uses high-gain differential feedback to amplify the difference between two input voltages. Within the product hierarchy, the TS321IDT is a general-purpose operational amplifier, a bipolar linear amplifier, and a member of the broader analog IC and semiconductor families. Its role is to increase signal amplitude while maintaining the closed-loop behavior established by external resistors or feedback networks. Key characteristics include the single-amplifier configuration, 800 kHz bandwidth, and 30 V maximum supply voltage. The manufacturer describes the device as a bipolar operational amplifier intended for compact, cost-sensitive designs. Its performance approach is intended to match or better selected industry-standard devices such as the LM358A and LM324 families, providing a familiar general-purpose solution without requiring a high-speed or precision-amplifier architecture. The TS321IDT operates from a dual supply extending to plus or minus 15 V, equivalent to a maximum total supply of 30 V. Its single-amplifier organization makes it appropriate when the PCB does not justify a dual or quad amplifier. Because it is a bipolar part rather than a CMOS amplifier, engineers should pay particular attention to input bias current, offset behavior, common-mode range, and output-swing limits during precision signal-chain design. Typical uses include buffering sensor outputs, amplifying low-level analog signals, active filtering, gain stages in measurement systems, and general industrial signal conditioning. It is particularly useful in compact equipment where an 8-pin SOIC footprint provides more mechanical flexibility than a small-outline package while maintaining low cost and straightforward PCB assembly. When laying out a TS321IDT circuit, place input, output, and decoupling connections according to the manufacturer pin-description table and keep feedback resistors close to the amplifier where practical. Confirm the required input common-mode voltage and output swing against the actual signal range. Stable operation also depends on suitable output loading and the compensation or feedback network selected for the intended gain. This page combines manufacturer and distributor information with an obsolete-lifecycle assessment, same-footprint alternatives, application guidance, and design considerations. It helps engineers distinguish a genuine circuit-compatible replacement from a merely similar single amplifier before committing a redesign to an active device.

طلب عرض سعر اتصل بنا
TS321ILT - 800kHz Low-Power Op Amp | STMicroelectronics
TS321ILT

TS321ILT - 800kHz Low-Power Op Amp | STMicroelectronics

STMicroelectronics TS321ILT is a single low-power bipolar operational amplifier with an 800 kHz gain-bandwidth product, 0.4 V/µs slew rate, and operation from 3 V to 30 V, housed in a compact SOT-23-5 package. The device supports output swing from approximately -1.5 V to +1.5 V under its stated operating conditions and is designed for general-purpose signal amplification where low cost, compactness, and low power consumption are important. An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses external feedback to set its gain and filtering behavior. The TS321 belongs to the low-power operational-amplifier hierarchy, combining common-mode input range, open-loop gain, output-drive capability, and stability in a small integrated circuit. Its bipolar implementation is intended for cost-sensitive applications where the SOT-23-5 package can save board space compared with larger SOIC implementations. The TS321ILT provides an 800 kHz gain-bandwidth product and 0.4 V/µs slew rate, making it appropriate for low-frequency audio, sensor conditioning, current monitoring, and general signal-shaping circuits. Its single-amplifier configuration reduces component count in applications that do not require a dual or quad amplifier. The 3 V to 30 V supply range also permits operation from conventional 5 V, 12 V, and 24 V industrial rails when the signal levels and dissipation permit. STMicroelectronics describes the TS321 as a bipolar low-power operational amplifier intended for space-constrained, cost-sensitive designs. The device is specified to match or improve relevant performance characteristics of established industry-standard amplifiers such as LM358A and LM324 families. Because it is a single amplifier, systems requiring several independent signal channels must use multiple TS321ILT devices rather than one dual or quad package. Typical uses include low-level sensor amplification, industrial control signal conditioning, audio preamplification, battery-powered instrumentation, and general analog buffers. In a practical inverting amplifier, the closed-loop bandwidth is determined by the feedback network as well as the 800 kHz gain-bandwidth product. Stable resistor and capacitor values should be selected with operating frequency, output swing, capacitive loading, and supply voltage taken into account. The main design consideration is to avoid treating the approximate output-swing limits as full rail-to-rail operation. Input and output signals must remain inside the specified common-mode and output ranges. Designers should also check the stability behavior of the chosen feedback topology under expected source capacitance and load capacitance because those board-level conditions influence practical amplifier performance. This product page combines the TS321ILT electrical specifications, package information, application guidance, and same-footprint replacement comparisons. It also provides practical guidance on feedback design, common-mode limits, supply selection, and PCB implementation so engineers can assess the amplifier before placing it in a new analog circuit.

طلب عرض سعر اتصل بنا
TS331ILT - 1.6V-5V Micropower Open-Drain Comparator | STMicroelectronics
TS331ILT

TS331ILT - 1.6V-5V Micropower Open-Drain Comparator | STMicroelectronics

STMicroelectronics TS331ILT is a single-channel, micropower, low-voltage comparator with open-drain output, rail-to-rail input capability, and a 1.6V to 5V supply range. The device is packaged in the compact SOT-23-5 surface-mount package and is intended for portable, battery-powered, sensor, and low-voltage signal-conditioning systems. Its typical supply current is as low as 20 uA, making it suitable for designs where comparator power consumption affects battery life. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input exceeds the other by more than its input-offset threshold. The TS331 belongs to the comparator, analog IC, and low-voltage power-management hierarchy. It uses an open-drain output, allowing the output to be pulled up externally when a wired-OR arrangement, level translation, or direct digital-interface connection is required. The TS331ILT operates from 1.6V to 5V and provides rail-to-rail inputs, allowing signals to be compared close to the supply rails without relying on a conventional mid-supply input range. The listed specifications include 26 uA supply current, 1 nA input bias current, 40 nA input offset current, 5 mV input offset voltage, 4.5 uV/°C temperature drift, 720 ns propagation delay, and 79 dB channel-to-channel rejection. These characteristics balance response speed, low power, and precision for compact embedded systems. The open-drain output is useful when several signals must be combined, but it requires an external pull-up resistor in most applications. The SOT-23-5 footprint supports dense PCB layouts, although correct input polarity and output-pull-up placement are important. The comparator can be used for voltage-threshold detection, battery monitoring, sensor signal conditioning, overvoltage detection, and portable equipment. Designers should select pull-up voltage and resistor values carefully, account for the open-drain output's rise time, and verify operation across the full temperature range. The TS331 family's low supply current and rail-to-rail inputs are particularly advantageous in 1.8V, 2.5V, and 3.3V systems where the signal range may span the full supply voltage. This product page combines the manufacturer specifications, package information, practical design guidance, and drop-in replacement considerations for engineers evaluating the TS331ILT in low-voltage comparator applications.

طلب عرض سعر اتصل بنا
TS339CD - Micropower Quad CMOS Comparator | STMicroelectronics
TS339CD

TS339CD - Micropower Quad CMOS Comparator | STMicroelectronics

STMicroelectronics TS339CD is a micropower quad CMOS voltage comparator containing four independent general-purpose comparators in a 14-pin SOIC package. Each comparator features open-drain CMOS outputs, extremely low input bias current, and a typical supply current consumption of 9 µA per comparator. The device provides a typical response time of 1.5 µs for a 5 mV input overdrive. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic result indicating which input is higher. The TS339 belongs to the broader comparator hierarchy, where a quad comparator integrates four independent analog-to-digital decision channels. Its CMOS construction combines low power consumption with high input impedance, making it suitable for battery-operated sensing, control, and signal-conditioning systems. The four channels can compare sensor outputs with adjustable references or supervise multiple operating conditions. Key characteristics include extremely low input bias current, a typical input offset current of 1 pA, and a typical input impedance of 10^12 ohms. The open-drain outputs allow the device to interface with pull-up resistors, level shifters, wired logic buses, and mixed-voltage systems. A typical response time of 1.5 µs for 5 mV overdrive supports applications requiring fast threshold decisions without the higher supply consumption commonly associated with bipolar comparator families. The TS339 is also described as pin-to-pin and functionally compatible with the bipolar LM339 family. This compatibility makes the open-drain architecture particularly useful when an existing board uses pull-up-based logic. Each comparator can independently monitor a sensor threshold, supply rail, window comparator, or control signal. Because the outputs are open drain, multiple device outputs can share a common pull-up when the system designer confirms that the combined sink-current and timing requirements remain acceptable. Typical uses include low-power battery monitoring, industrial threshold detection, sensor interface conditioning, overvoltage protection, and embedded control systems. The 14-pin SOIC package supports conventional surface-mount assembly and provides one channel per comparator, making channel assignment straightforward in multi-parameter monitoring systems. When laying out the circuit, route the comparator inputs away from switching nodes and place the open-drain pull-up resistors close to the output pins. Confirm input common-mode limits, supply-voltage range, output sink-current capability, and the effect of external pull-up resistance before using the device in a new design. This page combines the manufacturer's functional description, package information, comparator performance characteristics, verified cross-reference candidates, and practical design guidance to support component selection, schematic review, and PCB implementation.

طلب عرض سعر اتصل بنا
TS339CN - 16V Micropower Quad CMOS Comparator | STMicroelectronics
TS339CN

TS339CN - 16V Micropower Quad CMOS Comparator | STMicroelectronics

STMicroelectronics TS339CN is a micropower quad CMOS voltage comparator with four independent comparison channels, open-drain outputs, and a 14-pin through-hole DIP package. The device operates from a single supply up to 16 V, consumes 9 uA typical per comparator, provides 1 pA typical input offset current, and has input impedance of 10^12 ohms typical. These characteristics make it suitable for low-power sensing, threshold detection, and analog signal conditioning. A voltage comparator is an integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The TS339 belongs to the comparator hierarchy, where a comparator is a type of analog integrated circuit and signal-conditioning semiconductor. Its four channels provide flexible logic-level sensing, while the open-drain outputs allow wired connections or external pull-up networks when a push-pull output is not required. The principal benefits of the TS339CN are its low 9 uA typical supply current per comparator, extremely low 1 pA typical input offset current, and high 10^12 ohm typical input impedance. These characteristics reduce loading on high-impedance sensors and support battery-operated or low-leakage measurement systems. The open-drain architecture also supports wired-AND behavior, provided suitable pull-up resistors and an appropriate supply voltage are used. The TS339CN is designed around a CMOS input stage and four independent comparator channels. Its response time is 1.5 us typical for a 5 mV overdrive condition, making it suitable for many threshold and control functions where microsecond-scale decisions are sufficient. The manufacturer also identifies the device as pin-to-pin and functionally compatible with the bipolar LM339, which can simplify qualification of an existing comparator-based design. Typical uses include battery-powered sensor interfaces, low-voltage monitoring circuits, threshold detection, window comparators formed from pairs of channels, and general control logic. Because the outputs are open-drain, an application must include pull-up resistors whenever a valid high output level is required. The four-channel architecture also allows multiple independent measurements from a single IC. For a new through-hole design, allow adequate clearance around the 14-pin DIP footprint and route sensitive input traces away from switching nodes and output pull-up networks. Input common-mode range, output saturation levels, supply current, and output timing should be checked against the manufacturer datasheet for the intended supply voltage and temperature conditions. This page organizes the key TS339CN specifications, comparison information, practical design notes, and verified sourcing references. It also highlights the device's open-drain output architecture, low-power operation, and LM339 compatibility considerations for engineers evaluating PCB and firmware changes.

طلب عرض سعر اتصل بنا
TS339ID - Micropower Quad CMOS Comparator | STMicroelectronics
TS339ID

TS339ID - Micropower Quad CMOS Comparator | STMicroelectronics

STMicroelectronics TS339ID is a micropower quad CMOS voltage comparator with four independent open-drain outputs, a supply range of ±8 V to ±16 V, and a 14-pin SOIC package. Each comparator typically consumes 9 µA, while the device is designed for low-input-bias and low-input-offset-current measurements. A voltage comparator is an analog semiconductor that compares two input voltages and produces a digital logic result indicating which input is higher. The TS339ID belongs to the comparator hierarchy, combining four general-purpose channels in one package. Its CMOS construction reduces current consumption compared with a conventional bipolar LM339, while the open-drain outputs support wired logic, level translation, and systems using external pull-up resistors. Each channel provides non-inverting and inverting inputs. Key characteristics include extremely low input bias current, a typical input offset current of 1 pA, and typical input impedance of 10^12 ohms. The TS339ID is pin-to-pin and functionally compatible with the bipolar LM339 device. Its typical response time is 1.5 µs for a 5 mV overdrive, making it suitable for threshold detection rather than high-speed signal-chain comparison. The open-drain output architecture requires an external pull-up resistor when a logic-high level is needed. Because the output stage can pull the node low but cannot actively drive it high, several comparator outputs can be combined in a wired-AND arrangement. This characteristic is useful for supervision, window detection, and fault signaling, although circuit design must account for the pull-up value, output leakage, and bus rise time. Typical uses include power-supply sequencing, battery monitoring, overvoltage and undervoltage detection, temperature-control thresholds, industrial sensor interfaces, and simple digital control systems. The quad arrangement reduces board area and component count when four independent thresholds are required, particularly in industrial monitoring, instrumentation, and embedded-control equipment. Designers should verify input common-mode limits, output pull-up requirements, and absolute maximum supply voltage against the manufacturer datasheet before implementation. The open-drain node should include a pull-up to a valid logic rail, and unused inputs must be tied to a defined potential rather than left floating. PCB layout should keep sensitive input traces away from switching nodes and high-current return paths. This product overview combines the exact TS339ID characteristics with practical guidance for open-drain logic, threshold detection, PCB implementation, and comparison against pin-compatible LM339-family devices. It also organizes the available technical information for engineers evaluating power consumption, response time, input impedance, package compatibility, and lifecycle-sensitive redesigns.

طلب عرض سعر اتصل بنا
TS339IN - Micropower Quad CMOS Comparator | STMicroelectronics
TS339IN

TS339IN - Micropower Quad CMOS Comparator | STMicroelectronics

The STMicroelectronics TS339IN is a micropower quad CMOS voltage comparator with four independent channels, a 1.35 V to 16 V operating supply range, and a 14-DIP package. It features a 1 pA input bias current, 5 mV input offset voltage, and 1.5 microsecond response time, making it suitable for low-power signal conditioning. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital output indicating which input is higher. The TS339IN belongs to the comparator hierarchy, where four open-drain channels can monitor thresholds, detect crossings, supervise signals, or support feedback control. Its CMOS implementation provides low input bias current and low power consumption compared with classic bipolar comparator families. The TS339IN includes four general-purpose comparator channels with CMOS, open-drain outputs. The 1.35 V to 16 V supply range allows operation from low-voltage battery systems through conventional industrial rails, while the 1 pA typical input bias current reduces loading on high-impedance sensors. A 5 mV typical input offset voltage defines the baseline comparison accuracy, and the 1.5 microsecond response time supports threshold decisions without adding substantial propagation delay. Each comparator channel operates independently, allowing one device to implement four related decisions. The open-drain output architecture requires an external pull-up resistor, but it also provides flexible output-interface options. Designers can use the pull-up voltage to match downstream logic levels and can connect open-drain outputs in wired-AND configurations where appropriate. Dual-supply operation is supported up to a total supply span of 8 V. Typical uses include industrial sensor interfaces, battery-powered monitoring, digital control thresholds, window comparators, and general signal-conditioning systems. The low input bias current is particularly useful with resistive dividers, sensor outputs, and leakage-sensitive measurement circuits. The 14-DIP format also supports through-hole assembly and repairable industrial equipment where surface-mount packages would be inconvenient. When designing around the TS339IN, account for the open-drain output when selecting pull-up values and external logic supply levels. Keep input and output paths away from noisy switching nodes, and verify offset and common-mode behavior against the minimum signal separation required by the application. The operating range of -40°C to +125°C supports industrial temperature environments when the complete assembly is properly qualified. This product data combines the electrical characteristics, package details, cross-reference options, and practical design guidance needed to evaluate TS339IN. It also organizes pin assignments, application considerations, and compatible alternatives into a concise engineering reference for prototype development and production sourcing.

طلب عرض سعر اتصل بنا
TS339IPT - Micropower Quad Open-Drain Comparator | ST
TS339IPT

TS339IPT - Micropower Quad Open-Drain Comparator | ST

The STMicroelectronics TS339IPT is a micropower quad CMOS voltage comparator with four open-drain outputs, extremely low typical supply current of 9 μA per comparator, and operation across a 3 V to 16 V supply range. The device is packaged in a 14-pin TSSOP package and is intended for low-voltage, low-power signal-conditioning systems. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The TS339 belongs to the comparator hierarchy, combining four independent comparator channels with CMOS input stages and open-drain outputs. The TS339 family provides a practical alternative to higher-current bipolar LM339-family comparators in battery-powered and portable equipment. Key features include four comparator channels, a typical input common-mode range extending from ground to VCC minus 1.5 V, an output sink capability of 40 mA, and open-drain outputs that can be pulled up to a chosen external voltage. The low 9 μA typical current per comparator supports low-power sensing, while the 16 V maximum supply rating permits operation from a 3 V supply through higher-voltage industrial rails. These characteristics make the device suitable for threshold detection, battery monitoring, signal conditioning, and sensor interfaces. The open-drain architecture provides flexible output voltage levels but requires an external pull-up resistor on every output. The pull-up resistor establishes the high output level, while the output transistor actively pulls the line toward ground. This arrangement permits wired logic, level translation, and wired-AND behavior, although designers must account for the rise time created by the resistor and total bus capacitance. Input common-mode and output-level requirements must be checked against the actual supply voltage. Typical applications include portable battery monitoring, industrial sensor interfaces, window or level comparators, overvoltage detection, and low-power control systems. Because the TS339IPT is specified for the industrial temperature range, it can also be used in equipment exposed to temperatures from −40 °C to +125 °C. The 14-pin TSSOP package supports compact, surface-mount assembly but is relatively narrow and requires careful component placement. When designing a PCB around the TS339IPT, route the comparator inputs away from switching nodes and provide a short, quiet ground reference for each sensing point. Place pull-up resistors close to the corresponding open-drain outputs to minimize trace capacitance and improve switching speed. Confirm that the logic high generated by the pull-up meets the receiving device's input threshold, and verify that no signal connected to either comparator input exceeds the datasheet's absolute maximum ratings. This page combines the TS339IPT's principal electrical characteristics, verified package and distributor information, application guidance, comparison data, and practical replacement considerations to support faster component selection and board-level design.

طلب عرض سعر اتصل بنا
TS3702CD - Micropower Dual CMOS Comparator | STMicro
TS3702CD

TS3702CD - Micropower Dual CMOS Comparator | STMicro

The STMicroelectronics TS3702CD is a dual micropower CMOS voltage comparator with 9 uA typical supply current per comparator, a 2 us typical response time, and push-pull outputs, packaged in an 8-pin SOIC. The device provides two independent comparators with high input impedance, making it suitable for low-power sensing and threshold-detection circuits. A voltage comparator is an analog integrated circuit that compares an input voltage against a reference voltage and changes its digital output state when the compared signals cross. The TS3702 belongs to the comparator class within analog and mixed-signal semiconductors. Its push-pull CMOS outputs eliminate the external pull-up resistor normally required by open-collector comparators such as the bipolar LM393, reducing component count and simplifying output interfacing. The TS3702 operates from single or dual supplies and supports input common-mode ranges extending below and above the supply rails. Typical supply current is 9 uA per comparator, approximately twenty times lower than a bipolar LM393 according to the manufacturer datasheet. Input impedance is 10^12 ohms typical, helping minimize loading on high-impedance sensors. Maximum input offset voltage is listed as 6.5 mV, so applications requiring tighter threshold accuracy should include offset and propagation-delay error in the system budget. Each channel contains an input stage, a logic decision element, and a CMOS push-pull output driver. The push-pull stage sources or sinks output current, allowing direct connection to CMOS logic inputs. Because the output actively drives both states, the device does not need a pull-up resistor, although PCB design should still provide adequate output-current margin and account for the input capacitance of the following stage. Typical uses include battery-powered threshold detection, window comparators, sensor signal conditioning, overvoltage monitoring, temperature-setpoint control, and portable instrumentation. The dual-channel configuration also allows one package to implement a two-threshold window monitor or compare two independent sensor signals without adding a second comparator package. For low-noise analog signals, keep comparator input traces short, place the input reference network close to the device, and avoid routing them beside switching-node traces. Add supply-bypass capacitance near the power pins and verify that the output state never conflicts with another push-pull driver. Because the output is actively driven, do not connect two comparator outputs together without an isolation device. This page combines package and pin information with application guidance, drop-in candidate evaluation, comparison parameters, and practical design notes that help engineers move from datasheet review to a working low-power analog front end.

طلب عرض سعر اتصل بنا
TS3702CN - 9µA Dual CMOS Comparator | STMicroelectronics
TS3702CN

TS3702CN - 9µA Dual CMOS Comparator | STMicroelectronics

The STMicroelectronics TS3702CN is a micropower dual voltage comparator featuring 9 µA typical supply current per comparator, a 1.5 µs response time, and a 6.5 mV maximum input offset voltage. The device is packaged in an 8-pin DIP and uses a CMOS push-pull output stage. Its two independent channels support differential input comparisons with single or dual power-supply operation. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the measured relationship crosses a defined threshold. The TS3702 belongs to the comparator hierarchy within analog signal-conditioning integrated circuits. Two integrated channels in one package provide a practical way to monitor two thresholds, control one analog system, or implement complementary sensing functions while reducing board area. The TS3702's principal advantages are its very low 9 µA typical current consumption per comparator, CMOS input characteristics, and push-pull outputs. Unlike the open-collector outputs used by conventional bipolar comparators such as the LM393 family, push-pull outputs can drive a defined high or low state without an external pull-up resistor. This can simplify output interfacing and reduce board space, although the resulting output current and transition behavior must remain within the device specifications. According to the STMicroelectronics manufacturer datasheet, the TS3702 can operate from a single positive supply or from split positive and negative supplies. The available comparison information identifies a dual-supply operating span from ±1.35 V to ±8 V, with ±3 V and ±5 V listed as typical dual-supply configurations. Input offset voltage is specified up to 6.5 mV, while propagation delay can reach 1.5 µs. These values position the device for low-power threshold detection rather than high-speed timing applications. Typical uses include battery-powered sensor conditioning, overvoltage and undervoltage detection, temperature-limit monitoring, window comparators, and low-power control loops. The two channels may also monitor complementary supply or signal thresholds. A push-pull output is particularly useful when the next stage requires a CMOS-compatible logic level and the added quiescent current of an external pull-up network is undesirable. Designers should verify input common-mode range, output-current limits, supply sequencing, and output behavior for every operating condition using the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while comparator inputs require short, quiet traces that minimize coupling from switching nodes. The DIP package is suitable for through-hole assembly and prototypes, but modern compact products may require a different package variant and corresponding PCB redesign. This product page organizes the TS3702CN electrical characteristics, verified drop-in references, pin assignments, comparison parameters, and practical design guidance into one engineering-focused resource. It also distinguishes documented drop-in options from alternatives that require different packages or output structures, helping designers make a PCB-compatible sourcing decision.

طلب عرض سعر اتصل بنا
TS3702ID - Micropower Dual CMOS Comparator, 9uA, SOIC-8 | STMicroelectronics
TS3702ID

TS3702ID - Micropower Dual CMOS Comparator, 9uA, SOIC-8 | STMicroelectronics

The STMicroelectronics TS3702ID is a micropower dual CMOS voltage comparator that integrates two independent general-purpose comparators in an 8-pin SOIC-8 (SO-8) surface-mount package. Each channel consumes only 9 uA typical supply current, presents a 10^12 ohm typical input impedance and offers a 2.3 us typical response time, making it roughly twenty times lower in consumption than the classic bipolar LM393 reference circuit. A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output according to which input is higher. As a sub-type of the amplifier family, a comparator sits between raw sensing elements and a digital control path: it belongs to the broader hierarchy of analog ICs, amplifiers and comparators, signal conditioning, and ultimately power management and interface ICs. Its job is to translate a small analog difference into a logic-level decision without introducing supply noise or consuming significant battery current. Key features of the TS3702ID include a push-pull CMOS output stage, which removes the external pull-up resistor normally required by open-collector comparators and saves both board area and standby current. The device accepts a single supply from 2.7 V to 16 V or dual supplies from +/-1.35 V to +/-8 V, operates down to ground at the input common-mode range, and draws only 1 pA typical input offset current. The manufacturer also specifies pin-to-pin and functional compatibility with the bipolar LM393, which eases migration between designs. Internally the TS3702ID uses a CMOS process, giving near-zero input bias current and rail-to-rail CMOS output levels rather than saturated bipolar levels. The push-pull stage sources and sinks current actively, so output transitions are fast and the logic levels remain valid at low supply voltages where open-collector comparators would need extra headroom to guarantee a valid high level. Typical applications include battery-powered sensor and threshold monitoring, window comparators for over/undervoltage detection, low-current alarm and wake-up circuits, portable instrumentation, and general-purpose level detection in industrial control boards. When designing with the TS3702ID, remember that the output stage is push-pull, not open-collector, so no external pull-up resistor should be added. Confirm the input common-mode limits against the actual supply voltage in the manufacturer datasheet, and keep the input bias network impedance high so the 1 pA offset current does not shift the threshold. This page consolidates the manufacturer datasheet figures, distributor availability, package details, drop-in alternatives and practical design notes into one engineering reference that goes beyond the raw component listing.

طلب عرض سعر اتصل بنا
TS3702IN - Micropower Dual Comparator | STMicroelectronics
TS3702IN

TS3702IN - Micropower Dual Comparator | STMicroelectronics

STMicroelectronics TS3702IN is a micropower dual CMOS voltage comparator with 9 µA typical supply current per comparator, 1.5 µs maximum response time, and 6.5 mV maximum input offset voltage in an 8-pin PDIP package. Its two independent comparator channels use push-pull CMOS outputs, eliminating the external pull-up resistor normally required by open-collector comparators. A voltage comparator is an analog mixed-signal component that compares two input voltages and produces a logic-level output indicating which input is higher. The TS3702IN belongs to the comparator hierarchy within integrated circuits and analog signal-conditioning ICs. Its micropower operating current makes it suitable for battery-powered equipment where continuous supply consumption must remain low, while its dual-channel configuration provides two comparison functions in one package. The principal features are low power consumption, CMOS-compatible push-pull outputs, low input offset voltage, and a response time suitable for general-purpose signal detection. According to the STMicroelectronics TS3702 product page, the TS3702 consumes 9 µA typical per comparator, approximately twenty times less than a bipolar LM393. The 16 V maximum supply rating provides headroom for conventional 5 V and low-voltage industrial systems, while the 600 pA input bias current limits disturbance of high-impedance sensing nodes. Internally, the device combines CMOS input stages with two independent comparator channels. The push-pull output architecture actively drives both logic states, making the outputs suitable for direct connection to compatible CMOS inputs. This differs from open-collector comparators, which require an external pull-up resistor and can present slower rising edges when additional capacitance must be charged. Board designers should still check the output timing and load limits in the manufacturer datasheet when driving unusually long traces or high-capacitance nodes. Typical uses include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage monitoring, window comparators, and simple control loops. A second application is industrial sensing where low 9 µA typical current per comparator helps limit standby consumption. The TS3702IN can also supervise a divided supply rail by comparing its scaled voltage against a reference derived from another node. The principal design consideration is logic compatibility. Push-pull outputs must not be tied together or connected to a pull-up resistor in the manner used with open-collector outputs. Input common-mode range, output voltage levels, and propagation-delay limits must be checked against the actual supply voltage and connected logic family before finalizing the circuit. This product page combines the manufacturer specifications with package, sourcing, and replacement guidance for engineers evaluating the TS3702IN. It also identifies drop-in alternatives that retain the same 8-pin through-hole footprint, helping PCB designers compare functionality without introducing an unintended package migration.

طلب عرض سعر اتصل بنا
TS3704CD - Quad Micropower CMOS Comparator | STMicroelectronics
TS3704CD

TS3704CD - Quad Micropower CMOS Comparator | STMicroelectronics

The STMicroelectronics TS3704CD is a four-channel micropower CMOS voltage comparator with push-pull outputs, supplied in a 14-pin SOIC package. It is designed for low-power signal conditioning and is identified by the manufacturer as an obsolete part. The device accepts a 3 V nominal supply according to distributor product records, operates from 0°C to 70°C in the standard TS3704CD grade, and uses a 35 uA typical comparator current as listed for the closely matched TLC3704CD family. A voltage comparator is an analog integrated circuit that compares an input voltage with a reference voltage and changes its digital output state when the relationship between the two signals changes. The TS3704CD belongs to the comparator hierarchy: analog mixed-signal IC, voltage comparator, quad comparator, and power-management signal-conditioning IC. Four independent channels in one package can reduce board area and simplify designs requiring several threshold-detection or overvoltage-monitoring functions. The TS3704CD uses CMOS circuitry to limit consumption and a push-pull output stage to eliminate the external pull-up resistor normally required with open-collector comparators. The four channels share a common supply arrangement within the package, while each comparator provides its own non-inverting and inverting inputs and logic output. This makes the device applicable to threshold crossings, sensor interfaces, signal conditioning, and general-purpose digital logic interfaces. According to the manufacturer datasheet, the TS3704 is a micropower quad CMOS voltage comparator whose typical current is approximately 9 uA per comparator, while the identified TLC3704 comparison records state 35 uA. Push-pull outputs can drive CMOS-compatible loads directly and transition without the passive pull-up network associated with open-drain comparators. Designers should still check output current, supply voltage, input common-mode range, and output levels for each operating condition before reuse. Typical uses include battery-powered monitoring, industrial control thresholds, sensor signal conditioning, window comparison, and four-channel level detection. The 14-SO package is suitable for conventional through-hole assembly and prototype boards. Because TS3704CD is obsolete, engineers should use a qualified drop-in option when possible or confirm lifecycle, availability, and qualification requirements for long-term production programs. For a new PCB, preserve the 14-pin SOIC footprint and verify every signal against the replacement part's pin description. Pay particular attention to input common-mode range, propagation delay, output polarity, supply voltage, and input bias current, since a matching package alone does not guarantee equivalent behavior in every operating condition. This page consolidates lifecycle information, verified distributor records, pin-compatible migration options, comparison parameters, and practical replacement guidance. The structured alternatives help engineers move away from the obsolete TS3704CD without relying on a mechanically similar but electrically unsuitable part.

طلب عرض سعر اتصل بنا
TS3704CN - Micropower Quad CMOS Comparator | STMicroelectronics
TS3704CN

TS3704CN - Micropower Quad CMOS Comparator | STMicroelectronics

The STMicroelectronics TS3704CN is a micropower quad CMOS voltage comparator with four independent comparison channels, push-pull outputs, and a low typical supply current of 9 µA per comparator. The device is packaged in a 14-pin DIP and is designed for low-power threshold detection, signal conditioning, and voltage-level comparison. A voltage comparator is an analog semiconductor that compares an input voltage with a reference or threshold and changes its output when the relationship between those voltages changes. The TS3704 belongs to the comparator hierarchy within integrated circuits and analog signal conditioning. Compared with the bipolar LM339 family, its CMOS implementation consumes substantially less current and uses push-pull outputs, eliminating the external pull-up resistor normally required by open-collector comparators. The principal features of the TS3704CN include four CMOS comparator channels, 9 µA typical current consumption per comparator, a fast response time of 2 µs typical for a 5 mV overdrive, and typical input impedance of 10^12 ohms. Its push-pull output stage can drive logic inputs directly while reducing external component count. The device is also described as pin-to-pin and functionally compatible with the bipolar LM339, although output polarity, common-mode limits, supply behavior, and timing should still be checked before substitution. The TS3704 architecture supports four independent threshold or window-detection functions in one package. High input impedance reduces loading on high-impedance sensor nodes, while the low 9 µA typical consumption per comparator suits battery-operated equipment. The 2 µs typical response is useful for systems requiring fast decisions without moving to a higher-power comparator family. Its through-hole DIP-14 construction also favors legacy industrial, instrumentation, and educational designs where socketed or leaded assembly is preferred. Typical uses include battery-powered sensor interfaces, overvoltage and undervoltage detection, industrial control thresholds, window comparators, and low-power monitoring systems. The TS3704CN is particularly appropriate when one board requires several independent comparisons and when avoiding open-collector pull-up components materially simplifies the design. Designers should account for input common-mode range, supply voltage, output drive, and input overvoltage before assigning comparator inputs. Because this is a leaded DIP device, board spacing, soldering heat, and cleaning practices also affect long-term assembly reliability. Decoupling should follow the manufacturer datasheet guidance, especially when long PCB traces or switching sources are present. This product record combines the manufacturer datasheet, distributor identification, explicit package information, cross-reference candidates, and practical engineering guidance to support component selection, replacement assessment, PCB planning, and low-power comparator design.

طلب عرض سعر اتصل بنا
TS3704ID - 4-Comparator 9uA CMOS IC | STMicroelectronics
TS3704ID

TS3704ID - 4-Comparator 9uA CMOS IC | STMicroelectronics

The STMicroelectronics TS3704ID is a micropower quad CMOS voltage comparator with four independent comparison channels, 9 uA typical supply current per comparator, push-pull CMOS outputs, and a 14-pin SOIC package. It compares two input voltages and produces a logic-level result indicating which input is higher, making it suitable for precision threshold detection and low-power signal conditioning. A voltage comparator is an analog interface component that translates a difference between two voltages into a digital logic state. Within the broader hierarchy of integrated circuits and interface ICs, the TS3704 combines four analog comparison functions with low-power digital output stages. Unlike the open-collector outputs used by many bipolar comparator families, its push-pull outputs source and sink current directly, eliminating the external pull-up resistor normally required. Key characteristics include 9 uA typical current consumption per comparator, 1 TΩ typical input impedance, and a 2 us typical response time for a 5 mV input step. The high input impedance minimizes loading on high-impedance sensors and divider networks. A push-pull output also provides faster signal transitions and makes the device suitable for systems that need a direct active-high or active-low logic indication without an added pull-up resistor. The TS3704 uses CMOS input and output circuitry to achieve low bias current and low power consumption while retaining the pin arrangement associated with the LM339 family. Its four channels share supply pins but operate independently, allowing one package to implement battery monitoring, supervision, window comparison, or several unrelated threshold functions. Maximum offset voltage, input common-mode limits, supply range, and output-drive details should be checked against the manufacturer datasheet for the specific operating conditions. Typical applications include low-voltage battery monitoring, industrial sensor thresholds, consumer power-fail detection, overvoltage and undervoltage supervision, and comparison of external reference voltages. In portable equipment, the low 9 uA typical consumption per channel helps limit standby drain, while the four-channel integration reduces package count and board area compared with discrete single comparators. Designers should account for input common-mode range, output levels, propagation delay, and unused-channel behavior before assigning every comparator. Inputs must remain within their specified operating range, and unused channels should be configured according to the manufacturer guidance rather than left floating. PCB placement should keep sensitive comparison nodes away from switching nodes and high-current return paths to minimize coupled errors. This page organizes the TS3704ID electrical characteristics, package and pin information, application guidance, lifecycle status, and confirmed drop-in alternatives into one design-focused reference. It also identifies where a direct substitution is not established, helping engineers distinguish a true same-footprint replacement from a merely similar quad comparator.

طلب عرض سعر اتصل بنا
TS3704IN - 4-Channel Micropower CMOS Comparator | STMicroelectronics
TS3704IN

TS3704IN - 4-Channel Micropower CMOS Comparator | STMicroelectronics

The STMicroelectronics TS3704IN is a micropower quad CMOS voltage comparator with four independent comparison channels, push-pull outputs, and a 14-pin PDIP package. Each comparator typically consumes 9 µA, while the complete device is designed for low-power signal conditioning. According to the manufacturer datasheet, the TS3704IN supports input voltages up to ±8 V with a nominal 16 V supply and accepts a single supply from 3 V. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its digital output state when one input exceeds the other. This places the TS3704IN within the hierarchy of comparator IC, analog interface IC, and semiconductor. Four independent channels in one package reduce board area in threshold detection, window comparison, sensor conditioning, and control systems where several voltage relationships must be monitored. Key features include a push-pull CMOS output stage that eliminates the external pull-up resistor required by open-collector comparators. The typical input offset voltage is 5 mV, typical input bias current is 600 pA, and the response time is approximately 2 µs for a 5 mV overdrive. A nominal supply voltage of 3 V and an operating temperature range from -40 °C to +125 °C support both portable and industrial designs. The CMOS input stage provides high input impedance, helping the TS3704IN interface with high-impedance sensors without drawing substantial signal current. Its four-channel architecture also simplifies power sequencing because all comparators operate from the same supply. The push-pull output can actively drive both high and low states, although designers must account for the output current and voltage limits specified by the manufacturer when connecting loads. Typical uses include battery-powered threshold detection, industrial sensor interfaces, window comparators, overvoltage monitoring, control-system logic, and four-channel signal conditioning. In portable equipment, the 9 µA typical consumption per comparator is especially useful. For longer trace runs or noisy industrial environments, input filtering and careful grounding remain necessary even though the push-pull output reduces dependence on external pull-up hardware. PCB layout should keep input and output traces short, provide a stable ground reference, and place input filtering close to the comparator inputs. Because all four channels share supply pins, bypassing the supply close to the package helps minimize disturbance between channels. Avoid relying on the comparator output for functions requiring a pull-up resistor, since the TS3704IN output architecture is push-pull rather than open collector. This product page combines the manufacturer’s electrical characteristics, package and pin information, verified distributor listings, application guidance, and a strictly same-package alternative assessment. It is intended to help engineers determine whether the TS3704IN’s four channels, low current consumption, input impedance, and output architecture fit a specific low-power design.

طلب عرض سعر اتصل بنا
TS372CD - Dual Precision CMOS Comparator | STMicroelectronics
TS372CD

TS372CD - Dual Precision CMOS Comparator | STMicroelectronics

STMicroelectronics TS372CD is a low-power dual precision CMOS voltage comparator containing two independent differential comparators, with a response time of 600 ns, a single-supply operating range of 1.5 V to 8 V, and an 8-pin SOIC package. Each comparator provides CMOS, MOS, or TTL-compatible open-drain output operation for interfacing with mixed logic systems. A voltage comparator is an analog signal-processing IC that compares an input voltage against a reference voltage and changes its output state when the differential input crosses the switching threshold. A dual comparator integrates two independent channels into one package. Within the broader semiconductor hierarchy, TS372CD belongs to the comparator and amplifier IC family, where it bridges low-power analog sensing and digital logic control. The TS372CD emphasizes low power and precision. The manufacturer specifies a very low supply current of 0.1 mA per comparator, independent of supply voltage. Its extremely low input bias current is typically 1 pA, and its input offset current is also typically 1 pA. These characteristics reduce disturbance from high-impedance sensors and make the device suitable for monitoring systems where the source impedance could otherwise create input-related errors. Its differential CMOS architecture supports single-supply or dual-supply operation. The wide single-supply range extends from 1.5 V to 8 V, while the dual-supply capability covers positive and negative sensing ranges. The open-drain outputs require an external pull-up resistor when the output must rise to a positive logic voltage. This configuration provides flexible bus-level interfacing and permits wired-AND behavior when multiple outputs share a pull-up node. Typical uses include battery-powered threshold detection, sensor signal conditioning, window monitoring, overvoltage and undervoltage detection, and low-speed control loops. The 600 ns response time is appropriate for power-management, industrial-control, and instrumentation systems that require a rapid decision without the higher energy consumption of a high-speed comparator. Design the pull-up network around the required logic level, output rise time, and total capacitance. Place the pull-up resistor close to the output net, keep comparator input traces away from switching nodes, and account for input bias current when driving very high source impedances. Verify startup behavior and logic thresholds across temperature when the comparator controls a safety-critical or precision system. This product page combines the TS372CD electrical characteristics, package details, verified drop-in replacement information, comparison parameters, and practical interface guidance. It helps engineers evaluate whether its low-power precision architecture fits a design before checking the manufacturer datasheet and confirming application-specific limits.

طلب عرض سعر اتصل بنا
TS372CN - Dual CMOS Comparator, 8-DIP | STMicroelectronics
TS372CN

TS372CN - Dual CMOS Comparator, 8-DIP | STMicroelectronics

The STMicroelectronics TS372CN is a low-power dual CMOS voltage comparator with two independent comparison channels, a 1.5 V to 8 V single-supply operating range, support for dual supplies up to ±8 V, and an 8-DIP package. It produces open-drain, TTL-compatible outputs and combines very low supply current with extremely low input bias current. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a reference level. Comparators belong to the broader interface and signal-conditioning hierarchy, where they convert physical voltage relationships into logic-level events. The TS372CN’s dual-channel architecture provides independent decisions within one package, reducing board area compared with two separate single comparators. Key characteristics include supply current of 0.1 mA per comparator independent of supply voltage, input bias current of 1 pA typical, and input offset current of 1 pA typical. The device operates from a 1.5 V to 8 V single supply or from dual supplies within the stated ±8 V limit. Its open-drain outputs can support TTL-compatible interfacing, while the low-power operation is useful when continuously powered sensing is required. The CMOS input stage is suited to monitoring high-impedance sources because the extremely low bias current minimizes loading of the measured node. Each comparator can evaluate an input against a reference voltage or against the other input when configured as a differential comparator. The manufacturer datasheet should be consulted for the complete electrical characteristics, input common-mode limits, output sink-current limits, and propagation-delay curves. Typical applications include battery-powered threshold detection, sensor-condition interfaces, window comparators, overvoltage and undervoltage indication, low-level signal crossings, and general dual-threshold logic. Two independent channels can also implement hysteresis, zero-cross detection, or a pair of complementary limit checks without requiring two separate IC packages. Designers should account for the open-drain output architecture by providing a pull-up resistor at every output used with subsequent digital logic. Input common-mode voltage, output timing, and supply bypass requirements must remain within the manufacturer’s specified operating limits. Decoupling capacitance should be placed close to the supply pins, while sensitive input traces should be kept short and away from switching nodes. This page organizes the key electrical characteristics, commercial information, package details, application guidance, and available cross-reference information for engineers evaluating the TS372CN. It also highlights where a substitution requires direct pin and parameter verification rather than relying on package similarity alone.

طلب عرض سعر اتصل بنا
TS372ID - Dual CMOS Voltage Comparator, 8-SOIC | STMicroelectronics
TS372ID

TS372ID - Dual CMOS Voltage Comparator, 8-SOIC | STMicroelectronics

The STMicroelectronics TS372ID is a low-power dual CMOS voltage comparator in an 8-pin SOIC package. It contains two independent precision differential comparators designed for single-supply operation from 3 V to 16 V or dual-supply operation from plus or minus 1.5 V to plus or minus 8 V. Each comparator offers an open-drain output suitable for TTL-compatible interfacing. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The TS372ID belongs to the comparator category within analog and mixed-signal integrated circuits, where it is used for threshold detection, level sensing, signal conditioning, and simple control decisions. Its dual architecture allows two independent comparisons in one package, reducing component count when two threshold functions are required. The TS372ID uses STMicroelectronics silicon linMOS technology and emphasizes low power consumption. The manufacturer specifies a very low supply current of 0.1 mA per comparator, independent of supply voltage. Its extremely low input bias current is typically 1 pA, and its input offset current is also typically 1 pA, making the device suitable for high-impedance sensing circuits where source leakage could otherwise change the decision point. The wide operating-supply range allows the same device family to support low-voltage single-rail systems or balanced dual rails. Because the outputs are open-drain, each output requires an external pull-up resistor. This arrangement supports wired logic functions and allows the output transition speed to be adjusted through the pull-up resistance and circuit capacitance, but it also means an external pull-up is required to obtain a valid high output state. Typical uses include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage monitoring, window-comparison functions, and low-power control logic. When two comparators operate from the same supply, their individual input, output, and supply pins still require careful routing to avoid unintended coupling or output contention. For layout, place input and output traces away from high-current switching nodes and preserve a short return path to the supply ground. Select pull-up resistors according to the required rise time and available output current, and ensure that the input common-mode range remains within the limits stated in the manufacturer datasheet for the selected supply voltage. Decoupling capacitors should be placed close to the supply pins, with the ground connection kept short. This page organizes the TS372ID supply, input-current, package, output, and application information into an engineering-oriented selection guide. It also documents where to find the official datasheet, how to interpret the package and pinout, what to verify before making a replacement, and how to request a quotation through the XAIPART Request a Quote form.

طلب عرض سعر اتصل بنا