المنتجات (44,000+)

TS514ID - High-Speed Precision Quad Op Amp | STMicroelectronics
TS514ID

TS514ID - High-Speed Precision Quad Op Amp | STMicroelectronics

STMicroelectronics TS514ID is a high-speed, precision quad operational amplifier with four amplifier circuits, internally compensated frequency and phase response, short-circuit protection, internal ESD protection, and a 14-pin SOIC package. The verified product data identifies a maximum offset voltage of 500 uV and highlights a high gain-bandwidth product, low distortion, low noise, low power consumption, and high channel separation. The TS514ID is intended for instrumentation and general-purpose precision signal-processing designs requiring four amplifiers in one package. An operational amplifier, commonly called an op amp, is a voltage-controlled differential amplifier with very high open-loop gain. Its external feedback network determines the closed-loop behavior. The TS514 belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparators, and general-purpose voltage amplifiers. Internal phase compensation allows the TS514 to operate as a voltage follower despite its high gain-bandwidth product, reducing the external compensation effort required in many designs. The quad architecture integrates four amplifier channels into one 14-pin SOIC-14 package. Verified manufacturer-related product descriptions identify low offset voltage, low power consumption, short-circuit protection, low distortion, low noise, high gain-bandwidth product, high channel separation, and internal ESD protection. These characteristics make the device applicable to precision buffering, signal conditioning, instrumentation, industrial measurement, and general analog signal-processing systems. Each amplifier requires stable supply decoupling and careful handling of output-current limits. The TS514 uses internal frequency and phase compensation. This architecture is particularly useful in follower and precision-gain configurations because the compensation is already incorporated into the device. Its high speed does not eliminate the need for short feedback traces, adequate grounding, and supply bypassing. Designers should avoid long output routing and place input, output, and ground returns so that parasitic capacitance does not degrade stability or transient response. Typical uses include four-channel sensor conditioning, low-level signal amplification, active filtering, voltage buffering, and instrumentation chains requiring several matched amplifier functions. Industrial control and test equipment can also use the quad package to reduce board area compared with four discrete single-amplifier packages. Where precision offset and noise dominate, the complete manufacturer datasheet should be consulted for test conditions and application-specific limits. The principal design trade-off is speed versus power and stability margin. Although the TS514 supports high-speed operation and voltage-follower use, board layout, capacitive loading, output-current demand, and supply bypassing remain critical. A short, low-inductance layout with local decoupling is recommended. Application notes and the manufacturer datasheet should control the final compensation, grounding, and thermal implementation. This product page combines verified distributor and datasheet information with practical guidance on precision analog design, package reuse, selection criteria, and drop-in alternatives. It also distinguishes confirmed TS514-family candidates from cross-package or merely functional substitutes so engineers can avoid redesigns that require PCB changes.

طلب عرض سعر اتصل بنا
TS514IN - Quad Precision Op Amp | STMicroelectronics | DIP-14
TS514IN

TS514IN - Quad Precision Op Amp | STMicroelectronics | DIP-14

The STMicroelectronics TS514IN is a high-performance quad operational amplifier with internal frequency and phase compensation, supplied in a 14-DIP package. The device contains four amplifier channels in one package and is designed for general-purpose instrumentation, signal-conditioning, and analog control applications where stable voltage-follower operation is useful. The verified manufacturer description identifies low offset voltage, low power consumption, short-circuit protection, low distortion, low noise, high gain-bandwidth product, high channel separation, and internal ESD protection as key features. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. A quad operational amplifier extends this architecture to four independent channels in one package, reducing board area and simplifying multi-channel designs. The TS514IN belongs to the broader operational-amplifier, analog-amplifier, signal-conditioning, and semiconductor hierarchy. The TS514IN's compensated architecture is intended to support stable operation as a voltage follower despite its high gain-bandwidth product. Internal compensation simplifies circuit design when unity-gain stability is required, while short-circuit protection improves robustness in conventional analog signal paths. Low offset voltage supports precision-oriented instrumentation, and low noise and low distortion are useful for audio and measurement front ends. Four channels make the device suitable for sensor signal conditioning, current-voltage conversion, active filtering, waveform shaping, instrumentation amplifiers, feedback networks, and general analog control loops. The 14-DIP package is appropriate for through-hole prototyping, educational systems, laboratory instruments, and industrial assemblies where a dual-inline footprint is preferred over a fine-pitch surface-mount package. The principal design consideration is to verify the supply-voltage limits, input common-mode range, output swing, input bias current, noise density, and load-current behavior against the manufacturer datasheet before finalizing a new design. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be tied to a defined voltage within the input common-mode range. This page consolidates the verified manufacturer and distributor information, package details, application guidance, technical limitations, and drop-in replacement analysis. It also identifies parameters that require confirmation from the complete TS514 datasheet rather than substituting unverified assumptions.

طلب عرض سعر اتصل بنا
TS522ID - Dual 15MHz Low-Noise Op Amp | STMicroelectronics
TS522ID

TS522ID - Dual 15MHz Low-Noise Op Amp | STMicroelectronics

The STMicroelectronics TS522ID is a monolithic dual operational amplifier optimized for precision audio signal processing. It provides two amplifiers, a 15 MHz gain-bandwidth product, a 7 V/µs slew rate, low-voltage noise of 4.5 nV/√Hz, and a maximum input offset voltage of 850 µV in an 8-pin SOIC package. The device operates from 5 V to 30 V over an industrial temperature range of -40°C to +125°C. An operational amplifier is a voltage-controlled differential amplifier that uses feedback to amplify the difference between two input voltages. The dual configuration places two amplifiers in one package, allowing stereo audio, balanced signal paths, active filtering, or independent measurement channels to share a common footprint. Within the broader semiconductor hierarchy, the TS522 belongs to the operational-amplifier family, the analog amplifier category, and the signal-conditioning IC hierarchy. The TS522 combines low input offset, low voltage noise, and high dynamic performance for audio-oriented designs. Its 850 µV maximum input offset voltage supports accurate signal amplification, while the 4.5 nV/√Hz voltage-noise density is particularly relevant when processing low-level microphone, musical-instrument, or line-level signals. A 15 MHz gain-bandwidth product provides useful bandwidth for audio and general-purpose precision applications, and the 7 V/µs slew rate improves large-signal response. Internally, each amplifier is configured around high-gain stages with internal ESD protection. The manufacturer datasheet reports low distortion of 0.002%, macromodel inclusion, and excellent frequency stability. These characteristics make the TS522 suitable for precision audio signal chains where low noise, low distortion, and predictable frequency response matter more than very low power consumption. Typical uses include stereo audio preamplification, active crossover filters, mixer input stages, microphone preamplifiers, audio buffer circuits, and low-level sensor-conditioning channels. Two amplifiers in the same 8-pin SOIC package can reduce board area in stereo designs, while the industrial temperature range supports industrial control, communications, and instrumentation equipment. Designers should verify the required supply headroom, input common-mode range, output swing, noise gain, and stability for the selected feedback network. Decoupling capacitors should be placed close to the supply pins, and sensitive audio inputs should use short traces with suitable grounding to minimize parasitic pickup. A SPICE macromodel is available for circuit simulation, but board-level stability and distortion should still be verified with real components. This page consolidates the verified TS522ID operating characteristics, sourcing links, application guidance, design cautions, and replacement information. It also distinguishes confirmed technical facts from parameters that were not present in the supplied source data, helping engineers make a defensible design decision without treating unverified values as guaranteed specifications.

طلب عرض سعر اتصل بنا
TS522IDT - 15MHz Dual Low-Noise Op Amp | STMicroelectronics
TS522IDT

TS522IDT - 15MHz Dual Low-Noise Op Amp | STMicroelectronics

STMicroelectronics TS522IDT is a dual precision operational amplifier with a 15 MHz gain-bandwidth product, 4.5 nV/√Hz low-voltage noise, and a 7 V/µs slew rate. The device operates from 2.5 V to 15 V and is packaged in an 8-pin SOIC for dual-amplifier signal-conditioning applications. An operational amplifier is a voltage-controlled, high-gain analog building block that compares an input signal with a feedback-defined reference. The TS522IDT contains two amplifiers in one package, placing it within the operational-amplifier hierarchy of analog ICs and broader semiconductor signal-processing components. Its dual configuration reduces package count when a board requires two closely related analog channels. The primary benefits are low input offset voltage, low voltage noise, and high dynamic performance. A 4.5 nV/√Hz noise density supports accurate amplification of small signals, while the 15 MHz gain-bandwidth product provides useful bandwidth for audio, instrumentation, filtering, and general-purpose analog stages. The 7 V/µs slew rate allows the amplifiers to follow changing signals with limited distortion. Each amplifier can operate with supply voltages between 2.5 V and 15 V, allowing operation from low-voltage analog systems through higher-voltage industrial analog rails. The monolithic dual-amplifier construction is intended to provide matching behavior between the two channels, although circuit-level offset and noise measurements should still be checked in the final design. The 8-pin SOIC package supports conventional surface-mount assembly and is convenient for prototypes as well as production boards. Typical uses include low-noise audio preamplification, microphone signal conditioning, active filtering, instrumentation amplifiers, sensor interfaces, and analog buffering. Two independent amplifier channels can process stereo audio, implement a differential input stage, or combine filtering with output buffering. Supply-headroom planning remains important because the usable output range depends on the selected rail voltages and output load. For low-noise layouts, use short feedback paths, keep input and ground connections away from switching nodes, and place input bypass capacitance close to the supply pins. Decoupling requirements and compensation limits should be confirmed in the STMicroelectronics TS522IDT datasheet. Stable operation also depends on following the prescribed capacitive-load limits and providing suitable output-current margin for the connected load. This product page combines the verified TS522IDT specifications, package information, replacement considerations, comparison parameters, and application guidance. It is intended to help engineers determine whether the dual amplifier fits a specific voltage, bandwidth, noise, and PCB-layout requirement before completing a prototype or production design.

طلب عرض سعر اتصل بنا
TS522IN - 15MHz Dual Low-Noise Op Amp | STMicroelectronics
TS522IN

TS522IN - 15MHz Dual Low-Noise Op Amp | STMicroelectronics

The STMicroelectronics TS522IN is a monolithic dual precision operational amplifier primarily intended for audio applications. Each amplifier provides a 15 MHz gain-bandwidth product, a 7 V/us slew rate, and low voltage noise of 4.5 nV/sqrt(Hz). The device is offered in an 8-pin mini-DIP package for through-hole PCB assembly. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain and negative feedback to amplify, buffer, filter, or compare small voltage signals. The TS522 belongs to the operational-amplifier hierarchy within linear and amplifier ICs. Its dual-channel architecture integrates two amplifiers in one package, reducing board area and simplifying dual audio-path or differential-signal designs. The TS522IN emphasizes low-noise signal handling, low input offset voltage, and high dynamic performance. Manufacturer descriptions identify a maximum input offset voltage of 850 uV, voltage noise of 4.5 nV/sqrt(Hz), gain-bandwidth product of 15 MHz, and slew rate of 7 V/us. The device also includes internal ESD protection rated at 2 kV and a macromodel for simulation. These characteristics make it relevant to audio preamplification, active filtering, buffering, and general low-noise analog signal chains. The dual amplifier can process two related signals independently, including left and right audio channels or the positive and negative sides of a differential circuit. Its 15 MHz bandwidth provides useful bandwidth for audio and wider-band analog stages, while the 7 V/us slew rate supports rapidly changing waveforms. The 4.5 nV/sqrt(Hz) voltage-noise figure helps reduce amplifier-added noise in high-gain stages, making the TS522IN most useful when the signal source impedance, resistor selection, and feedback topology are controlled carefully. Typical applications include stereo audio preamplifiers, microphone preamplifiers, active low-pass filters, audio buffers, sensor-conditioning stages, and small-signal audio-driver interfaces. The mini-DIP package is appropriate for legacy through-hole designs, test equipment, prototypes, and applications where hand insertion or socket assembly is preferred. Surface-mount production should use an electrically and mechanically verified SO-8-family option rather than assuming the DIP package is interchangeable. When designing around the TS522IN, begin with the power-supply limits and common-mode input range listed in the manufacturer datasheet. Confirm that source and sink output-current requirements remain within the operating limits at the selected gain and load. Place input and feedback components close to the device, maintain a stable ground reference, and use appropriate bypassing at each supply pin. Decoupling capacitors should be placed at the amplifier pins rather than at a distant power entry point. This page consolidates the TS522IN technical characteristics, package constraints, sourcing guidance, application fit, and verified cross-reference information. It also distinguishes documented device attributes from parameters that require confirmation in the manufacturer datasheet, helping engineers assess the part before PCB and production decisions.

طلب عرض سعر اتصل بنا
TS524ID - Quad Low-Noise Audio Op Amp, 15MHz, SOIC-14 | STMicroelectronics
TS524ID

TS524ID - Quad Low-Noise Audio Op Amp, 15MHz, SOIC-14 | STMicroelectronics

The STMicroelectronics TS524ID is a monolithic quad operational amplifier for precision audio signal paths, integrating four low-noise, high-fidelity amplifiers on one silicon die in a 14-pin SOIC (SO-14) surface-mount package. It combines a 15 MHz gain-bandwidth product, a 7 V/µs slew rate and 4.5 nV/√Hz input voltage noise with an input offset voltage of 950 µV maximum and total harmonic distortion of 0.002%. An operational amplifier, or op amp, is a high-gain differential amplifier with two inputs and one output that is used to amplify small signals faithfully across a wide frequency range. A quad op amp such as the TS524ID contains four independent amplifiers in one package, giving audio and instrumentation designers four signal-path stages, two input buffers and one output driver from a single 14-pin device. In the broader semiconductor hierarchy, the TS524ID sits in the linear amplifier family, inside instrumentation and buffer amplifiers, which are themselves part of the analog integrated-circuit category. Key features of the TS524ID include the very low input offset voltage of 950 µV max, low voltage noise of 4.5 nV/√Hz, a high gain-bandwidth product of 15 MHz, a high slew rate of 7 V/µs and low distortion of 0.002%. The device also carries internal ESD protection rated at 2 kV, so it tolerates handling transients without external clamps on most board designs. A SPICE macromodel is included in the specification, which lets you simulate the real frequency-dependent behaviour of the amplifier instead of an ideal voltage source. Architecturally, the TS524ID is built on a bipolar process, which is the classic choice for audio-grade amplifiers because it delivers high transconductance, low crossover distortion and predictable large-signal behaviour into the 600 Ω to 10 kΩ impedances typical of line-level audio stages. The wide-bandwidth output stage allows the amplifier to swing cleanly at high frequencies, so the same device can serve as a preamplifier, a headphone-driver helper stage or an active filter stage without changing the bill of materials. The four amplifiers in the package share a common supply pair, and each channel is independent, so the die can be used for four single-ended paths or two stereo pairs. Typical applications include stereo audio preamplification, headphone and line-level output buffers, active crossover and equalisation filters, microphone conditioning stages, mix-console sub-buses and general instrumentation. The 15 MHz loop-gain bandwidth means the open-loop gain is still usable at audio-band frequencies, which matters for filter design where a 24 dB/octave active filter needs flat open-loop phase response. When designing around the TS524ID, keep the feedback network close to the device and use a resistor divider for gain rather than a single high-value feedback resistor, because the input bias current produces offset error proportional to the total resistance seen at the input. Place the bypass capacitor for the supply pins as close to the package as the layout allows, because the 15 MHz bandwidth can couple supply ripple directly into the audio band if the on-board supply impedance is high. This page adds value beyond the manufacturer datasheet by combining verified distributor availability information, drop-in and cross-brand equivalents in the same SOIC-14 footprint, a parameter-by-parameter comparison table, and practical design notes for audio, filtering and instrumentation work.

طلب عرض سعر اتصل بنا
TS524IDT - Low-Noise Quad Op Amp | STMicroelectronics
TS524IDT

TS524IDT - Low-Noise Quad Op Amp | STMicroelectronics

The STMicroelectronics TS524IDT is a monolithic quad operational amplifier with four amplifiers in a 14-pin SOIC package. It provides very low input voltage noise of 4.5 nV/√Hz, a maximum low-frequency input offset voltage of 950 µV, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. Designed for precision low-noise signal processing, the device is particularly suited to audio applications and other circuits requiring low distortion. An operational amplifier is a high-gain, differential analog amplifier used to amplify, buffer, filter, or control voltage signals. Quad operational amplifiers combine four amplifiers in one package, reducing board area and simplifying multi-channel designs. The TS524 belongs to the operational-amplifier hierarchy within analog and mixed-signal integrated circuits, where low input noise, low offset voltage, wide bandwidth, and high slew rate determine how faithfully small signals can be amplified. The TS524's 4.5 nV/√Hz input-noise density is the central feature for audio and precision instrumentation. Its low-noise behavior reduces the amplifier's contribution to the total input-referred noise, helping preserve small signals in microphone, line, and measurement front ends. A 15 MHz gain-bandwidth product supports wider signal bandwidth, while the 7 V/µs slew rate enables faster output transitions than lower-bandwidth general-purpose amplifiers. The device also offers a low maximum input offset voltage of 950 µV, which helps reduce output error when the amplifier is used with high closed-loop gain. Its output stage supports large output excursions, and its low distortion specification is 0.002%. Together, these characteristics make the TS524 suitable for balanced audio channels, active filters, line-level signal conditioning, and precision analog signal chains operating from low-noise sources. Typical uses include four-channel audio preamplification, microphone and line-input conditioning, active crossover or equalization networks, and instrumentation requiring consistent low-noise amplification. Because all four amplifiers are integrated in one package, channel matching and board-space savings are additional practical benefits for multichannel analog designs. Designers should verify the supply-voltage range, input common-mode range, output swing, and stability requirements in the STMicroelectronics manufacturer datasheet before finalizing the analog front end. Decoupling capacitors should be placed close to the supply pins, and sensitive input routes should be kept short to minimize board-level interference and added noise. This page organizes the verified TS524IDT specifications, source links, application guidance, and replacement analysis into an engineering-focused reference. It also highlights the device's 4.5 nV/√Hz noise, 15 MHz bandwidth, 7 V/µs slew rate, 950 µV maximum offset voltage, and 14-pin SOIC implementation for faster component evaluation.

طلب عرض سعر اتصل بنا
TS524IN - Quad Low-Noise Precision Op Amp | STMicroelectronics
TS524IN

TS524IN - Quad Low-Noise Precision Op Amp | STMicroelectronics

The STMicroelectronics TS524IN is a monolithic quad operational amplifier designed for low-noise audio applications, with four amplifier circuits in a 14-pin DIP package. Its headline performance includes a 15 MHz gain-bandwidth product, 7 V/us slew rate, and 4.5 nV/sqrt(Hz) input-voltage-noise density. The device operates from 5 V to 30 V and supports output swings across approximately plus or minus 2.5 V to plus or minus 15 V. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to improve signals applied to its two inputs. The TS524 belongs to the broader hierarchy of operational amplifier, instrumentation amplifier, analog amplifier, and semiconductor. Its four-channel configuration reduces the number of packages required in stereo, surround-sound, mixer, and other multi-channel audio signal paths while preserving consistent performance across each amplifier. Key characteristics include very low input-offset voltage, 4.5 nV/sqrt(Hz) voltage-noise density, 80 dB gain bandwidth or signal-to-noise performance identified for the device, 250 nA input-bias current, and 0.8 uA input-bias current figure listed for the family. The 37 mA per-channel current rating reflects the operating conditions associated with the amplifier family. These characteristics make the TS524 useful where microphone signals, line-level audio, or control signals require low-noise amplification and wide bandwidth. The TS524 combines four precision operational amplifiers in one monolithic IC. Its 15 MHz gain-bandwidth product supports moderate-gain audio stages, while the 7 V/us slew rate improves large-signal response compared with slower general-purpose amplifiers. The low 4.5 nV/sqrt(Hz) input noise helps preserve quiet signal chains, and the low input-bias current reduces errors when operating with high-impedance sources. Its stated supply range accommodates both positive single-supply operation and dual-supply audio systems. Typical uses include stereo preamplifiers, audio mixer stages, active crossover networks, microphone preamplifiers, headphone-driver signal chains, and four-channel surround-sound processing. In each case, the quad arrangement can simplify routing between channels and conserve board area, although independent de-coupling and careful grounding remain necessary when multiple amplifiers share one package. PCB design should keep input and feedback paths short, connect a suitable bypass capacitor near each supply pin, and maintain a quiet return-current path. Decoupling between amplifier channels can reduce interaction through the shared supply network. Designers should also verify output swing, load capability, stability with the selected feedback network, and thermal behavior against the intended supply voltage and signal level before releasing the layout. This product record combines the TS524 family specifications with package details, application guidance, selection criteria, and practical design notes. It helps engineers distinguish the 14-pin DIP TS524IN from differently packaged family members while focusing attention on the measured electrical characteristics that matter in low-noise audio circuitry.

طلب عرض سعر اتصل بنا
TS555CD - 2.7MHz CMOS Timer | STMicroelectronics | SOIC-8
TS555CD

TS555CD - 2.7MHz CMOS Timer | STMicroelectronics | SOIC-8

STMicroelectronics TS555CD is a single CMOS 555-type timer/oscillator operating from 2 V to 16 V, with a maximum frequency of 2.7 MHz and typical supply current of 100 µA at VCC = 5 V. The device is supplied in an 8-pin SOIC package and supports both astable and monostable timing. Its low power consumption and higher operating frequency distinguish it from the conventional bipolar NE555. A 555 timer is an analog timing integrated circuit that combines resistive timing, a voltage comparator, a flip-flop, and a high-current output stage. Within the broader semiconductor hierarchy, the TS555CD is a clock and timing IC, then a programmable timer and oscillator, and finally a general-purpose timing component used in industrial control, pulse generation, delay circuits, and signal processing. The TS555 family provides low typical supply current of 100 µA at 5 V, while the manufacturer product page lists 110 µA at VCC = 5 V. Its maximum astable frequency is 2.7 MHz, compared with 0.1 MHz for the conventional NE555. This frequency capability makes the TS555CD suitable for compact oscillator and pulse-generation circuits that require faster timing than the classic bipolar implementation. STMicroelectronics describes the TS555 as pin-to-pin and functionally compatible with the bipolar NE555. It can operate in astable mode as a free-running oscillator or in monostable mode as a one-shot pulse generator. The output stage supports high output current, while reduced supply-current spikes during output transitions help limit disturbance on sensitive power rails. Typical uses include industrial delay circuits, sensor activation timers, low-power oscillators, LED flashers, control pulse generators, and embedded system timing. Because the TS555CD is listed as obsolete by a distributor record, engineers should confirm lifecycle availability with authorized distributors or qualify an alternative before new production releases. Designers should not assume that every 555-family device is interchangeable at high frequency or across the complete supply range. Check pinout, output polarity, timing tolerance, maximum frequency, supply voltage, output-current capability, and package dimensions against the specific replacement. Decoupling capacitors should be placed close to the supply pins, and timing components should be positioned to minimize switching-node coupling. This page consolidates verified manufacturer and distributor specifications, lifecycle information, practical replacement guidance, and application-focused engineering notes. It provides a concise purchasing and design reference while clearly separating confirmed data from parameters that still require manufacturer confirmation.

طلب عرض سعر اتصل بنا
TS555CDT - 2.7 MHz CMOS Timer | STMicroelectronics
TS555CDT

TS555CDT - 2.7 MHz CMOS Timer | STMicroelectronics

The STMicroelectronics TS555CDT is a single CMOS programmable timer and oscillator rated for operation up to 2.7 MHz, with a typical supply current of 110 µA at 5 V, housed in an 8-pin SOIC package. The device supports a 2 V to 16 V supply range and provides the standard 555 timer functions in both astable and monostable configurations, combining low power consumption with substantially higher operating frequency than the classic bipolar NE555. A programmable timer is an integrated circuit that generates or measures a time interval using external resistors and capacitors. The TS555 belongs to the 555 timer family within the broader clock and timing IC hierarchy. Its internal voltage reference, comparators, discharge transistor, and flip-flop allow one device to create periodic waveforms, produce fixed-duration pulses, or measure elapsed time. The CMOS implementation retains the familiar timing architecture while reducing supply current and output-transition current spikes. Key features include a maximum timer frequency of 2.7 MHz, typical supply current of 110 µA at a 5 V supply, and operation across a 2 V to 16 V supply range. These characteristics suit battery-powered timers, low-cost automation circuits, pulse generators, debounce circuits, and general-purpose delay networks. Compared with a bipolar NE555, the CMOS TS555 provides substantially lower consumption and a much higher maximum frequency, supporting smaller timing capacitors and more compact high-frequency implementations. The TS555 uses the standard 555 timing architecture and remains pin-compatible with the familiar 8-pin NE555 footprint. Timing accuracy is maintained in astable and monostable modes, while reduced supply-current spikes during output transitions can permit smaller decoupling capacitors than a bipolar implementation. The control-voltage pin provides a means of adjusting the internal threshold reference within the device's allowed range. Typical applications include low-cost oscillators for LED blinking or clock generation, retriggerable and non-retriggerable monostable pulse circuits, transistor switching circuits, sensor debounce networks, delayed-action controls, and low-power embedded timing. In battery-operated products, its low typical supply current reduces standby burden, while the 16 V upper supply limit supports many 12 V industrial systems when voltage and dissipation conditions permit. When implementing the device, calculate the timing resistors and capacitors for the required frequency and duty cycle, and place the timing capacitor directly at the threshold and trigger pins to minimize noise pickup. Use a stable reference capacitor at the control-voltage pin and provide adequate input bypassing. Confirm that the maximum frequency, supply voltage, output-load capability, and timing tolerances suit the intended operating environment. This page combines the TS555CDT's principal electrical characteristics, package and pin information, application guidance, and pin-compatible sourcing considerations. It is intended to help engineers identify where the CMOS 555 architecture improves power consumption and frequency capability while preserving the standard timer interface.

طلب عرض سعر اتصل بنا
TS555CN - 2.7MHz Low-Power CMOS Timer | STMicroelectronics
TS555CN

TS555CN - 2.7MHz Low-Power CMOS Timer | STMicroelectronics

The STMicroelectronics TS555CN is a low-power, single CMOS timer with a maximum astable frequency of 2.7 MHz, a typical supply current of 100 µA at 5 V, and an operating supply range up to 18 V, housed in an 8-pin DIP package. It provides the familiar 555 timer functions in astable and monostable configurations while offering pin-to-pin and functional compatibility with the bipolar NE555. A 555 timer is a programmable timing IC that combines a resistor, capacitor, and internal threshold comparator into a compact oscillator or one-shot pulse generator. The TS555CN belongs to the CMOS timer, oscillator, and clock-and-timing hierarchy: it can generate continuous periodic waveforms in astable mode or produce a timed output pulse in monostable mode. Its CMOS implementation is especially useful in low-power and higher-frequency circuits where lower supply current than a conventional bipolar NE555 is valuable. Key features include very low typical supply current, a maximum astable frequency of 2.7 MHz, wide operating voltage support to 18 V, high input impedance, and output compatibility with TTL, CMOS, and logic families. According to the STMicroelectronics manufacturer datasheet, typical supply current is 110 µA at 5 V and 90 µA at 3 V, with reduced current spikes during output transitions. These characteristics make the device practical for portable timing, pulse generation, debouncing, and periodic-control applications. Internally, the TS555CN uses CMOS circuitry to implement the comparator, flip-flop, discharge transistor, and timing-control functions of a standard 555 timer. In astable operation, two external resistors and one capacitor establish the oscillation period; in monostable operation, one resistor and one capacitor set the pulse width. The external timing elements determine practical accuracy, while the timer provides repeatable thresholding and state control. Typical uses include low-power delay circuits, oscillator clocks, LED flashers, pulse generators, debounce networks, and control timing in embedded equipment. The TS555CN can also replace a standard NE555 where the circuit permits CMOS supply current and operating-voltage differences. Before substitution, verify trigger-level, output-drive, timing-tolerance, and maximum-frequency requirements against the actual design. For PCB layout, keep the timing capacitor and resistor leads short, connect the decoupling capacitor close to VCC and GND, and avoid long traces around high-impedance threshold and control pins. Because the DIP package has exposed through-hole leads, mechanical spacing and soldering cleanliness should also be considered. This page combines manufacturer specifications, verified distributor information, replacement guidance, and practical design notes for engineering selection.

طلب عرض سعر اتصل بنا
TS555ID - 2.7MHz Low-Power CMOS Timer | STMicroelectronics
TS555ID

TS555ID - 2.7MHz Low-Power CMOS Timer | STMicroelectronics

The STMicroelectronics TS555ID is a single CMOS 555-type timer and oscillator with a 2.7MHz maximum frequency, low typical supply current, and an 8-pin SOIC package. It operates from 2 V to 18 V and is designed for both astable and monostable timing circuits. According to the STMicroelectronics product page, typical supply current is 110 µA at VCC = 5 V, compared with 3 mA for the bipolar NE555. A CMOS timer is a clock-and-timing semiconductor that generates a time-delayed output or an adjustable oscillation when combined with passive resistors and capacitors. The TS555 belongs to the 555 timer family, which combines a comparator, flip-flop, discharge transistor, and voltage reference in one integrated circuit. This integration allows a timer or oscillator to be implemented without separate logic gates, while retaining the familiar resistance-and-capacitance timing method. The TS555ID provides a maximum astable frequency of 2.7 MHz, substantially higher than the 0.1 MHz maximum cited for the NE555 in the supplied manufacturer data. Its CMOS implementation also reduces supply-current spikes during output transitions. These characteristics make the device useful in low-power pulse generation, delay circuits, waveform generation, debounce timing, and embedded control applications where accurate timing and low quiescent consumption are important. The TS555 is pin-to-pin and functionally compatible with the bipolar NE555 according to the supplied datasheet description. Its wide 2 V to 18 V supply range supports legacy 5 V systems as well as higher-voltage industrial and embedded rails. The exact trigger and threshold timing tolerances, output-current limits, temperature range, and absolute maximum ratings are not present in the provided data and therefore require confirmation in the manufacturer datasheet before final design release. Typical uses include RC astable oscillators, retriggerable and non-retriggerable monostable multivibrators, pulse-width timing, debounce networks, and low-frequency clock generation. In an astable circuit, external resistors and a capacitor set the operating frequency; in monostable operation, the same timing principle produces a controlled output pulse after a trigger event. Designers should use the external timing-component tolerances as part of the total timing error and verify output-drive current against the selected load. Decoupling should be placed close to the supply pins, and the timing capacitor and resistors should be positioned to minimize leakage, contamination, and parasitic capacitance. PCB cleanliness is particularly important because contamination can change effective resistance and disturb oscillator frequency. This page consolidates manufacturer specifications, verified distributor listings, package details, practical design guidance, and explicitly qualified replacement information. It is intended to support engineering selection while separating verified values from parameters that still require confirmation from the full STMicroelectronics datasheet.

طلب عرض سعر اتصل بنا
TS555IDT - 2.7MHz Low-Power CMOS Timer | STMicroelectronics
TS555IDT

TS555IDT - 2.7MHz Low-Power CMOS Timer | STMicroelectronics

STMicroelectronics TS555IDT is a single CMOS programmable timer IC with a maximum astable operating frequency of 2.7 MHz, a 2 V to 16 V supply range, and an 8-pin SOIC package. The device provides low-power operation, with typical supply current of 110 µA at 5 V, while supporting both monostable and astable timing configurations. A programmable timer is a timing IC that uses external resistors and capacitors to generate a delayed pulse or a periodic waveform. The TS555 belongs to the 555 timer family, which combines a voltage reference, comparators, a flip-flop, and a discharge transistor in one package. Its CMOS implementation places it within the broader semiconductor hierarchy of clock and timing ICs and programmable timer controllers. The principal advantages of the TS555IDT are its 2.7 MHz maximum frequency, low 110 µA typical supply current at 5 V, and pin-to-pin and functional compatibility with the bipolar NE555. It supports supply voltages from 2 V to 16 V and an operating temperature range of -40°C to 125°C, making it suitable for precision timing, pulse generation, delay, and oscillator circuits across industrial and consumer systems. Internally, the TS555 uses two comparators to monitor the timing voltage on the threshold and trigger nodes. A resistor-capacitor network controls these nodes, while the internal flip-flop determines the output state and the discharge transistor provides the reset interval. Accuracy remains stable in both one-shot and free-running modes, and the CMOS process also reduces supply-current spikes during output transitions. Typical applications include LED and lamp flashers, debounce timers, pulse-width modulation, missing-pulse detection, periodic interrupt generation, audio tone generation, and simple RC oscillators. Its SOIC-8 package supports conventional surface-mount assembly, while its low consumption is useful in battery-operated and low-duty-cycle equipment. When designing around the TS555IDT, maintain adequate input bypass capacitance and keep timing components close to the threshold and trigger pins. Confirm discharge-device current, output-drive capability, and duty-cycle limits against the load. Because this exact ordering code is listed as obsolete, engineers should review current STMicroelectronics timer options before committing a new production design. This page organizes the key electrical limits, package information, pin functions, cross-reference alternatives, and practical application guidance into a compact engineering reference. It also highlights the operating distinctions that matter when comparing the TS555 with other CMOS and bipolar 555 timer implementations.

طلب عرض سعر اتصل بنا
TS555IN - 2.7 MHz Low-Power CMOS Timer | STMicroelectronics
TS555IN

TS555IN - 2.7 MHz Low-Power CMOS Timer | STMicroelectronics

The STMicroelectronics TS555IN is a single CMOS programmable timer and oscillator with a maximum astable frequency of 2.7 MHz, a 2 V to 16 V supply range, and an 8-pin DIP package. It is designed for low-power timing and oscillator circuits while retaining compatibility with the conventional bipolar NE555 function and pin arrangement. A programmable timer is an integrated circuit that combines timing elements, comparators, a flip-flop, and a high-current output stage into one device. The TS555IN belongs to the 555 timer family, which sits within clock and timing ICs and can operate as a monostable one-shot or an astable free-running oscillator. This integration removes the need for discrete comparator, flip-flop, and discharge-transistor networks in common delay and pulse-generation circuits. The principal advantages are low supply consumption, high operating frequency, and reduced supply-current spikes during output transitions. The cited manufacturer product page reports typical TS555 supply current of 110 uA at a 5 V supply, while a distributor specification listing reports 65 uA under its specified test conditions. The maximum astable frequency of 2.7 MHz is substantially higher than the 0.1 MHz maximum commonly associated with the bipolar NE555 in the supplied comparison data. The TS555IN supports both one-shot and free-running operation. In monostable mode, its output changes state for a controlled interval after an external trigger. In astable mode, external resistors and a capacitor establish repeated output oscillations. The 2 V to 16 V operating range permits use from low-voltage battery-powered equipment through higher-voltage industrial control circuits, subject to the component's detailed absolute maximum ratings. Typical uses include pulse generation, delayed switching, debounce and missing-pulse circuits, simple oscillators, LED flashers, industrial timing modules, and control-signal generation. Its CMOS implementation is particularly useful where standby supply current matters, while its 2.7 MHz maximum frequency supports higher-rate timing than the bipolar reference timer. Designers should preserve the standard 555 interface when making PCB substitutions and should account for the TS555's low-voltage limitations, timing tolerances, and output-drive behavior. Supply bypassing and timing-component placement should follow the manufacturer datasheet, especially in astable circuits operating near the 2.7 MHz upper frequency limit. This product page consolidates manufacturer specifications, distributor availability information, verified cross-reference results, and practical selection guidance. It also distinguishes true same-package replacements from functionally similar timer families that may require different pinouts, voltage tolerances, or application-level qualification.

طلب عرض سعر اتصل بنا
TS555IPT - 2.7 MHz CMOS Timer, 8-TSSOP | STMicroelectronics
TS555IPT

TS555IPT - 2.7 MHz CMOS Timer, 8-TSSOP | STMicroelectronics

The STMicroelectronics TS555IPT is a single CMOS programmable timer and oscillator rated for a maximum astable frequency of 2.7 MHz and supplied in an 8-pin TSSOP package. Its principal operating specifications include a typical supply current of 110 µA at VCC = 5 V, a supply-voltage range up to 18 V, and operation over a temperature range of -40 °C to 125 °C. The device provides the standard 555 trigger, threshold, output, discharge, reset, and control functions needed to generate accurate time delays or periodic waveforms. A 555 timer is a programmable timer IC that can operate as a monostable one-shot or an astable oscillator. Within the broader semiconductor hierarchy, the TS555 belongs to the clock and timing IC category and can also function as a voltage comparator when configured conventionally. Its CMOS implementation reduces consumption compared with the classic bipolar NE555 while retaining pin-to-pin and functional compatibility with established 555 timer circuits. The TS555IPT combines low power consumption, high maximum operating frequency, and reduced supply-current spikes during output transitions. Its CMOS implementation is useful in battery-powered equipment, compact control systems, signal-processing modules, and industrial electronics where supply efficiency and surface-mount packaging are important. The 8-TSSOP format also supports automated board assembly and reduces the footprint compared with larger through-hole timer packages. Timing accuracy remains available in both monostable and astable operating modes. In monostable operation, an external trigger starts one timed output pulse whose duration is determined by resistance and capacitance. In astable operation, external timing components continuously charge and discharge an internal timing node to produce a continuous output waveform. The maximum astable frequency of 2.7 MHz makes the device suitable for substantially faster timing applications than conventional low-frequency NE555 implementations. Typical uses include LED flashers, pulse generators, debounce circuits, industrial control timing, appliance interfaces, and compact sensor or communications modules. Because the TS555IPT supports both positive and negative trigger inputs, it can also implement Schmitt-trigger-style signal conditioning. Board designers should account for the TSSOP lead pitch and place timing, control, and bypass capacitors close to their associated pins. When designing the circuit, verify trigger and reset pulse widths against the operating conditions in the manufacturer datasheet, and ensure the discharge-device voltage and current remain within their rated limits. A local supply bypass capacitor is recommended near the VCC and ground pins to suppress switching transients, especially in high-frequency astable operation. This product overview combines the TS555IPT electrical characteristics, package details, functional behavior, cross-reference findings, and practical design guidance into one engineering-focused reference for timer selection, PCB implementation, and replacement evaluation.

طلب عرض سعر اتصل بنا
TS556CD - Dual CMOS Timer, 2.7MHz, 14-SOIC | STMicroelectronics
TS556CD

TS556CD - Dual CMOS Timer, 2.7MHz, 14-SOIC | STMicroelectronics

The STMicroelectronics TS556CD is a low-power dual CMOS 555-type timer and oscillator with a maximum frequency of 2.7 MHz, a 2 V to 16 V supply range, and a 14-pin SOIC package. The device combines two independent timer sections, low typical supply current, and pin-to-pin and functional compatibility with the bipolar NE556, making it suitable for precision timing, pulse generation, delay, and oscillator circuits. A 555-type timer is an analog timing integrated circuit that compares an externally controlled voltage with threshold and trigger levels. In monostable mode, it produces one timed output pulse; in astable mode, it oscillates continuously when configured with external resistors and capacitors. The TS556CD uses CMOS circuitry to reduce power consumption while retaining the familiar dual-timer architecture. Key verified features include a maximum astable frequency of 2.7 MHz, low-power operation, and supply current listed in the source data at approximately 130 µA in one distributor summary, while the manufacturer-family description specifies 220 µA typical at VCC = 5 V for TS556. The discrepancy reflects different device variants or source summaries; application designs should verify the exact datasheet value for the ordered part. The 14-SOIC package is suitable for conventional PCB assembly and through-hole-compatible external connections. The TS556CD is useful in pulse-width generation, delay circuits, waveform generation, LED flashing, industrial control timing, low-power signal generation, and embedded control systems. Its dual sections allow two timers in one package when board area is constrained. Because timing accuracy depends on resistor tolerances, capacitor stability, supply variation, and output loading, those components should be selected for the target frequency and temperature range. The principal design consideration is confirming output drive, supply voltage, timing limits, and pin-level compatibility with the surrounding circuit. The manufacturer describes the family as functionally and pin-to-pin compatible with the bipolar NE556, but load conditions and supply-specific timing behavior still require review before substitution. The TS556CD is listed as obsolete by one distributor source, so procurement should confirm lifecycle status and availability before committing to a production design. This page combines the verified TS556CD specifications, sourcing information, lifecycle observations, and application guidance to support design triage. It also highlights why a same-package timer replacement must be checked for frequency, voltage, timing, and output-load compatibility rather than selected by footprint alone.

طلب عرض سعر اتصل بنا
TS556CDT - Dual 2.7MHz Timer IC | STMicroelectronics
TS556CDT

TS556CDT - Dual 2.7MHz Timer IC | STMicroelectronics

STMicroelectronics TS556CDT is a dual CMOS 555-type timer and oscillator with two independent timing channels, a maximum astable frequency of 2.7 MHz, and a 2 V to 16 V supply-voltage range. The device is packaged in a 14-pin SOIC and is pin-to-pin and functionally compatible with the bipolar NE556 timer family. Each channel can operate as a monostable pulse generator or an astable oscillator, making the TS556CDT suitable for timing, delay, pulse generation, modulation, and simple clock-generation circuits. A 555-type timer is a clock-and-timing integrated circuit that compares an externally controlled timing voltage with a reference threshold and switches an output when the voltage crosses that threshold. In the monostable configuration, one external resistor and capacitor determine a single output pulse. In the astable configuration, two resistors and a capacitor establish continuous oscillation. The TS556 family belongs to the broader semiconductor hierarchy of clock and timing ICs, timer ICs, programmable timers, and oscillators. The TS556CDT provides a maximum astable operating frequency of 2.7 MHz and operates from 2 V to 16 V. Its low power consumption is a notable characteristic: the manufacturer datasheet lists a typical supply current of 220 µA at 5 V and 180 µA at 3 V. One distributor technical listing reports 130 µA supply current, demonstrating that the operating-current figure can vary with supply voltage and test conditions. The commercial-temperature TS556CDT is specified for an operating range of 0 °C to 70 °C. Using CMOS construction allows the TS556CDT to provide the functional behavior of the classic 555 timer in a low-power, dual-channel implementation. Both timer sections can be used independently, which reduces component count when a board requires two related timing functions. Equivalent internal oscillators can produce clocks for digital systems, while independently configured channels can create delayed pulses, retriggerable one-shots, window timers, or simple tone-generating circuits. Typical applications include industrial control and instrumentation, digital delay networks, pulse-generation circuits, low-power sensor interfaces, tone generation, debounce and delay networks, embedded control systems, and general-purpose clock-generation modules. The 14-pin SOIC package is suitable for conventional surface-mount PCB assembly and allows straightforward hand soldering during prototype development. When using the TS556CDT, calculate the timing resistor and capacitor tolerances because both directly determine pulse width and oscillation frequency. Keep the timing node away from noisy high-current traces, use a bypass capacitor close to the supply pins, and verify the discharge-transistor peak current against the chosen timing resistor. For battery-powered equipment, compare both operating current and the leakage contribution of the timing capacitors against the complete power budget. This page combines the core electrical limits, operating-temperature range, package details, pin-compatibility information, application guidance, and selection considerations needed to evaluate the TS556CDT. It also identifies three closely related TS556 family ordering variants and clearly distinguishes their package and temperature-grade verification needs for drop-in replacement planning.

طلب عرض سعر اتصل بنا
TS556CN - Dual 2.7MHz CMOS Timer | STMicroelectronics
TS556CN

TS556CN - Dual 2.7MHz CMOS Timer | STMicroelectronics

The STMicroelectronics TS556CN is a dual low-power CMOS timer with two independent 555-compatible timing sections, a maximum astable frequency of 2.7 MHz, and a 14-DIP package. Its verified supply-voltage range is 2 V to 16 V, while one secondary result describes the family operating to 18 V; the exact maximum for this orderable device must therefore be confirmed from its datasheet before use. The TS556CN provides 180 µA typical supply current at 3 V and is designed for accurate monostable and astable operation. A CMOS timer is a programmable time-delay and oscillator integrated circuit. It belongs to the timer/oscillator category, within clock and timing ICs and broader semiconductor devices. Each timer section uses external resistors and capacitors to set delay or oscillation behavior, making this device useful where conventional 555-type timing, pulse generation, delay, and repetitive switching are required without a microcontroller. Key verified attributes include dual-timer construction, operation from 2 V to 16 V, a high maximum astable frequency of 2.7 MHz, and pin-to-pin and functional compatibility with bipolar NE556 devices. Reduced supply-current spikes during output transitions can permit lower decoupling capacitance than a conventional bipolar implementation. The stated 180 µA typical current at 3 V supports battery-conscious designs, although load and switching conditions must be checked against the datasheet. The TS556CN uses CMOS circuitry to combine low quiescent consumption with higher timer frequency than the bipolar NE556 comparison cited in the search data. That comparison reports 2.7 MHz maximum frequency for TS556 versus 0.1 MHz for NE556. However, actual operating frequency depends on timing resistors, capacitors, propagation delays, output loading, and supply voltage, so high-frequency layouts require short traces and careful grounding. Typical uses include LED and lamp flashers, pulse generators, delay stages, debounce or retriggerable timing networks, simple oscillators, industrial control timers, and low-power instrumentation. The 14-DIP through-hole package favors prototypes, educational designs, repairable assemblies, and human-built electronics where a socketed or perforated-board implementation is practical. Design with the two timer sections independently unless datasheet pin behavior explicitly permits shared connections. Place timing components close to their associated pins, bypass the supply near the device, and account for output-current limits and threshold tolerances. Because the web evidence provides conflicting voltage-range wording, use the 2 V to 16 V range for this listing and verify absolute maximum and operating limits before releasing production hardware. This page combines verified distributor and datasheet findings, package-aware replacement analysis, and practical timer-circuit guidance. It also distinguishes documented TS556CN data from specifications that were not supplied, avoiding unsupported claims about pricing, lifecycle, compliance, or exact pin assignments.

طلب عرض سعر اتصل بنا
TS556ID - Dual 2.7MHz CMOS Timer | STMicroelectronics
TS556ID

TS556ID - Dual 2.7MHz CMOS Timer | STMicroelectronics

The STMicroelectronics TS556ID is a dual CMOS 555-type timer and oscillator with two independent timing sections, operation from 2 V to 16 V, a maximum astable frequency of 2.7 MHz, and typical supply current of 220 µA at 5 V. It is supplied in a 14-pin SOIC package. The TS556ID combines 555 timer compatibility with CMOS power efficiency and higher timing frequency than the traditional bipolar NE556. A 555-type timer is a programmable clock and timing semiconductor that can operate as a monostable one-shot or astable oscillator. In system hierarchy, the TS556ID belongs to clock and timing ICs, timer ICs, oscillators, and semiconductors. Each internal timer provides resistive and capacitive timing inputs, trigger and reset controls, and an output stage. Two independent sections allow one circuit to generate two events, delays, tones, or periodic waveforms. The verified data identifies the TS556 as a pin-to-pin and functionally compatible bipolar NE556 design, while reducing typical supply current to 220 µA at a 5 V supply. Another source lists 180 µA typical at 3 V. Its 2.7 MHz maximum astable frequency allows shorter timing periods and higher-frequency waveform generation than a 0.1 MHz NE556, subject to the datasheet's timing limits, component tolerances, and output-drive conditions. The TS556ID supports monostable and astable operating modes. In monostable service, an external trigger produces a timed output pulse whose duration is determined primarily by external resistance and capacitance. In astable service, external timing components charge and discharge an internal node, producing continuous oscillation. Engineers should calculate the timing values from the manufacturer datasheet, include realistic resistor and capacitor tolerances, and verify output rise and fall behavior in the intended load. Typical uses include low-power pulse generation, delayed actuator triggering, LED and indicator flashing, audible tones, small signal-clock generation, industrial control timing, and embedded system timing support. The dual architecture is especially useful when two related but nonsynchronous events are needed. Compared with a NE556, the principal benefits are lower typical consumption and a substantially higher maximum astable frequency; NE556 compatibility does not mean every electrical limit is identical. Design with the 2 V to 16 V supply range in mind, especially the output behavior at low supply voltage. Keep the reset and trigger paths free of unwanted noise, select timing-component tolerances for the required frequency accuracy, and provide the bypass and output-loading conditions required by the datasheet. Because timing accuracy depends on real component values and parasitics, breadboard validation is advisable for high-frequency or precision intervals. This page combines verified manufacturer and distributor information, practical timing guidance, and a conservative assessment of drop-in replacements. It distinguishes documented electrical facts from parameters that require datasheet confirmation, helping engineers locate the TS556ID datasheet, evaluate purchasing options, and decide whether a same-package substitute is suitable for an existing PCB.

طلب عرض سعر اتصل بنا
TS556IDT - Dual CMOS Timer, 2.7MHz, SOIC-14 | STMicroelectronics
TS556IDT

TS556IDT - Dual CMOS Timer, 2.7MHz, SOIC-14 | STMicroelectronics

The STMicroelectronics TS556IDT is a dual CMOS 555-type timer and oscillator designed for low-power timing, monostable, astable, and pulse-generation circuits. It provides a maximum astable operating frequency of 2.7 MHz, operates from a 2 V to 16 V supply, and is packaged in a 14-pin SOIC. The device is pin-to-pin and functionally compatible with bipolar NE556 timer families, while its CMOS implementation reduces supply-current demand and improves switching behavior in precision timing applications. A 555 timer is a programmable time-delay and oscillator building block within the broader clock and timing IC category. Each TS556 timer section contains a voltage reference, comparators, a flip-flop, discharge transistor, and an output stage. The timing interval is set by external resistors and capacitors connected to the RC timing pins. Typical uses include delayed switching, pulse stretching, debounce circuits, lamp flashers, simple oscillators, and frequency dividers. Key characteristics include a 2.7 MHz maximum astable frequency, a wide 2 V to 16 V operating supply range, and low power consumption. The manufacturer identifies the TS556 as a dual CMOS timer with typical supply current of 220 uA at VCC = 5 V, compared with approximately 6 mA for the NE556(a) bipolar family. The available technical description also identifies the TS556 as pin-to-pin and functionally compatible with bipolar NE556(a) devices. The dual configuration allows two independent timing channels in one package, reducing component count and board area when an application needs simultaneous or complementary timing functions. The TS556IDT is suitable for industrial control, sensor interfaces, pulse generation, low-power instrumentation, embedded timing modules, and general-purpose oscillator circuits. Its SOIC-14 package supports conventional surface-mount assembly while retaining the familiar dual 555 interface. When designing a replacement board, use the manufacturer pin-description table to preserve trigger, threshold, control-voltage, discharge, and output connections. Confirm the intended mode of operation and external RC network before changing timing components. The 2.7 MHz figure is a maximum astable-frequency capability, and actual operating frequency depends on resistor and capacitor values, load conditions, supply voltage, and timing tolerances. For systems requiring exact timing accuracy, evaluate the minimum and maximum RC values and the propagation behavior of the output stage over the intended voltage and temperature ranges. This page combines the TS556IDT datasheet information, package details, timing-use context, and practical replacement guidance to support faster component selection and PCB-level integration.

طلب عرض سعر اتصل بنا
TS556IN - Dual 2.7 MHz CMOS Timer | STMicroelectronics
TS556IN

TS556IN - Dual 2.7 MHz CMOS Timer | STMicroelectronics

The STMicroelectronics TS556IN is a low-power dual CMOS 555-type timer and oscillator with a maximum astable operating frequency of 2.7 MHz, supplied from 2 V to 16 V and packaged in a 14-pin DIP. Each half of the device can operate as a monostable timer, astable oscillator, or frequency divider. The dual timer uses CMOS construction to reduce supply consumption, with one verified source quoting a typical supply current of 100 µA at VCC = 5 V. The TS556 family is also described as pin-to-pin and functionally compatible with the bipolar NE555, which simplifies replacement of legacy timer circuits. A programmable timer is an oscillator-and-triggering circuit that produces a timed output pulse. A 555-type timer belongs to the clock and timing IC hierarchy: timer and oscillator > programmable timer > clock and timing integrated circuit > semiconductor. In monostable mode, one trigger produces a pulse of a defined duration. In astable mode, the two internal comparators and flip-flop repeatedly charge and discharge an external timing capacitor, creating continuous pulses. Two independent timer sections can therefore control separate events or generate related timing sequences. The TS556IN combines several useful characteristics for timer applications. Its maximum astable frequency is 2.7 MHz, allowing short timing periods when supported by suitable external resistors and capacitors. The verified operating-voltage information identifies a 2 V minimum supply and a 16 V maximum supply for TS556IN. Additional family-level features include high output-current capability, reduced supply-current spikes during output transitions, and compatibility with bipolar NE555 implementations. The reported operating-temperature range is -40 °C to +125 °C, supporting industrial-temperature designs. Internally, the TS556 is a CMOS implementation of the classic dual-timer architecture. Each section uses voltage thresholds, a discharge transistor, and an output stage to compare an external capacitor voltage with control levels derived from the supply voltage. CMOS operation is principally valuable for low supply consumption and reduced switching activity compared with the bipolar NE555. Designers must still account for timing-component tolerance, output rise and fall behavior, and the maximum astable frequency when setting high-frequency operating conditions. Typical uses include pulse generation, delay and retrigger circuits, periodic switching, lamp and motor control, low-frequency oscillators, and two-channel industrial timing systems. TS556IN is particularly appropriate where a through-hole 14-DIP footprint and dual timer are required rather than a surface-mount package. In an astable oscillator, external R-A, R-B, and capacitor C values determine the repetition rate and duty cycle; the 2.7 MHz maximum frequency is an important upper-bound constraint for high-speed timing designs. The primary design consideration is preserving the 555-compatible timing architecture while allowing adequate tolerance and ESR for the selected capacitor. Place timing components close to the device, keep discharge-current paths compact, and avoid excessive loading of the threshold and trigger nodes. Because the part is supplied in a through-hole DIP package, board spacing, connector accessibility, and thermal performance should be checked before using it in new compact designs. This product page consolidates verified distributor specifications, manufacturer-family information, application guidance, packaging details, and available replacement references. It distinguishes directly documented TS556IN characteristics from family-level or distributor-supplied information and explicitly identifies data that remains unavailable, allowing engineers to make sourcing and design decisions without relying on unverified assumptions.

طلب عرض سعر اتصل بنا
TS5A2053 - 10Ω SPDT Analog Switch | Texas Instruments
TS5A2053

TS5A2053 - 10Ω SPDT Analog Switch | Texas Instruments

The TS5A2053 is a single-pole double-throw (SPDT) analog switch from Texas Instruments, designed to operate from 1.65 V to 5.5 V. It can handle both digital and analog signals, and signals up to V+ can be transmitted in either direction. The device features a low ON-state resistance of 10Ω (typical) and includes an enable pin for power management. It is available in the 8-pin VSSOP (DCU) package, making it suitable for space-constrained applications. An analog switch is a semiconductor device that selectively connects or disconnects an analog signal path based on a digital control signal. It is a fundamental building block in signal routing, multiplexing, and sample-and-hold circuits. Analog switches are part of the broader category of interface ICs, which manage signal integrity and connectivity between different subsystems in electronic systems. Key features of the TS5A2053 include a low ON-state resistance of 10Ω, which minimizes signal attenuation, and a wide operating voltage range from 1.65 V to 5.5 V, allowing compatibility with various logic levels. The device also offers fast switching speeds, with a typical turn-on time of 20 ns and turn-off time of 15 ns, making it suitable for high-frequency signal routing. The enable pin allows the switch to be disabled, reducing power consumption in standby modes. Technically, the TS5A2053 uses a CMOS process that provides low power consumption and high ESD robustness. The device has a bandwidth of 300 MHz, enabling it to pass high-frequency signals with minimal distortion. The ON-state resistance is flat across the input voltage range, ensuring consistent performance. The device also features break-before-make switching, preventing momentary short circuits between channels. Typical applications include audio signal routing, data acquisition systems, and test equipment. In audio systems, the low ON-state resistance and high bandwidth ensure minimal signal degradation. In data acquisition, the switch can route analog signals to an ADC, with the enable pin allowing power saving when not in use. In test equipment, the TS5A2053 can be used for signal multiplexing and routing. When designing with the TS5A2053, it is important to consider the ON-state resistance and its effect on signal integrity. For high-frequency signals, the parasitic capacitance of the switch can cause signal attenuation, so proper PCB layout and termination are recommended. Additionally, the enable pin should be tied to a defined logic level to avoid floating inputs.

طلب عرض سعر اتصل بنا
TS5A3159QDBVRQ1 - 1Ω SPDT Analog Switch AEC-Q100 | TI
TS5A3159QDBVRQ1

TS5A3159QDBVRQ1 - 1Ω SPDT Analog Switch AEC-Q100 | TI

The Texas Instruments TS5A3159QDBVRQ1 is an automotive-qualified (AEC-Q100) single-pole double-throw (SPDT) 2:1 analog switch with 1Ω typical ON-state resistance (1.3Ω max), operating from a 1.65V to 5.5V supply in a 6-pin SOT-23 (DBV) package. An analog switch is a semiconductor device that routes or gates analog and digital signals under the control of a logic-level input. Within the signal-chain hierarchy, the SPDT analog switch sits in the analog switches and multiplexers family, below large multiplexer arrays and alongside transmission-gate logic. An SPDT device connects one common (COM) terminal to either of two throw terminals (NO or NC), making it the fundamental building block of signal routing and redundancy switching. Key features include break-before-make switching, which prevents momentary channel shorting during transition and eliminates signal distortion when a signal source moves between paths; an excellent total harmonic distortion (THD) specification that preserves audio and precision-signal integrity; and low ON-resistance matching and flatness, which minimize signal error across the input range. The device operates from a single 1.65V to 5.5V supply, compatible with 1.8V, 2.5V, 3.3V, and 5V logic systems. The switch core uses a low-charge-injection MOS transmission-gate architecture with approximately 8pF typical ON capacitance (per TI family data), limiting high-frequency insertion loss in data and RF routing paths. The digital IN pin is logic compatible across the full supply range, and the -Q1 suffix denotes AEC-Q100 qualification with -40C to +125C operation for automotive environments. Typical applications include automotive audio source selection, sensor-signal multiplexing in battery-management and body-control modules, UART/SPI/SMBus line sharing, and general-purpose signal gating in industrial systems. The 2.9mm x 1.6mm SOT-23-6 footprint suits densely populated boards. Design tip: terminate or AC-ground unused throw terminals to reduce crosstalk, and place the device close to the signal source to minimize parasitic trace capacitance. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

USD $0.28 اتصل بنا
TS5L100D - 4-Channel 5V SPDT LAN Switch | Texas Instruments
TS5L100D

TS5L100D - 4-Channel 5V SPDT LAN Switch | Texas Instruments

The Texas Instruments TS5L100D is a 4-channel, 2:1 SPDT LAN switch operating from a 5 V supply and packaged in a 16-pin SOIC. It is designed as a four-bit 1-of-2 multiplexer/demultiplexer with one common switch-enable input, allowing paired signal paths to be routed through a compact analog switching stage. The device is identified by the manufacturer as a wide-bandwidth LAN switch with low on-state resistance. A LAN switch is an analog signal-routing component used to select between two signal paths on each channel. In the TS5L100D, four independent SPDT channels share a single enable control, making the device suitable for systems that need synchronized routing of multiple differential or single-ended network-related signals. The common enable architecture reduces the number of control inputs required when all channels must change state together. The primary design benefits of the TS5L100D are its 4-channel integration, 5 V supply operation, 2:1 SPDT configuration, and low on-state resistance. Combining four switch elements in one 16-SOIC package can simplify board planning compared with four discrete SPDT packages. Low on-state resistance helps preserve signal integrity when the switch is inserted into a transmission path, while the wide-bandwidth positioning makes the device relevant to LAN signal-routing designs. The TS5L100D is used when a design requires multiplexing or demultiplexing across multiple related channels rather than independent routing of unrelated signals. Common applications include network-interface signal selection, test and measurement signal-path routing, communication equipment, and embedded systems that must switch between two external signal sources. The shared enable input is particularly useful when paired or grouped channels need coordinated selection. For layout, place the device near the signal paths it serves and route the four channels consistently to minimize trace-length differences and unintended coupling. Keep the enable trace short and away from high-energy switching nodes. Confirm the exact pin assignments, recommended supply bypassing, control thresholds, insertion loss, bandwidth, and operating-temperature limits in the manufacturer datasheet before finalizing a production board. This product page organizes the TS5L100D function, package information, sourcing path, comparison points, and application guidance into one engineering reference. It also highlights the important trade-off between integration and board flexibility: the four-channel common-enable architecture is efficient for coordinated LAN routing, while designers needing independently controlled or differently configured paths should confirm that the shared-control arrangement matches the system architecture.

طلب عرض سعر اتصل بنا