TS3702ID - Micropower Dual CMOS Comparator, 9uA, SOIC-8 | STMicroelectronics
MPN: TS3702ID ✓ نشطTS3702ID نظرة عامة
A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output according to which input is higher. As a sub-type of the amplifier family, a comparator sits between raw sensing elements and a digital control path: it belongs to the broader hierarchy of analog ICs, amplifiers and comparators, signal conditioning, and ultimately power management and interface ICs. Its job is to translate a small analog difference into a logic-level decision without introducing supply noise or consuming significant battery current.
Key features of the TS3702ID include a push-pull CMOS output stage, which removes the external pull-up resistor normally required by open-collector comparators and saves both board area and standby current. The device accepts a single supply from 2.7 V to 16 V or dual supplies from +/-1.35 V to +/-8 V, operates down to ground at the input common-mode range, and draws only 1 pA typical input offset current. The manufacturer also specifies pin-to-pin and functional compatibility with the bipolar LM393, which eases migration between designs.
Internally the TS3702ID uses a CMOS process, giving near-zero input bias current and rail-to-rail CMOS output levels rather than saturated bipolar levels. The push-pull stage sources and sinks current actively, so output transitions are fast and the logic levels remain valid at low supply voltages where open-collector comparators would need extra headroom to guarantee a valid high level.
Typical applications include battery-powered sensor and threshold monitoring, window comparators for over/undervoltage detection, low-current alarm and wake-up circuits, portable instrumentation, and general-purpose level detection in industrial control boards.
When designing with the TS3702ID, remember that the output stage is push-pull, not open-collector, so no external pull-up resistor should be added. Confirm the input common-mode limits against the actual supply voltage in the manufacturer datasheet, and keep the input bias network impedance high so the 1 pA offset current does not shift the threshold.
This page consolidates the manufacturer datasheet figures, distributor availability, package details, drop-in alternatives and practical design notes into one engineering reference that goes beyond the raw component listing.
بدائل مباشرة لـ TS3702ID — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع TS3702ID (نفس عامل الشكل والبصمة) — يختلف في Operating Temperature Range, Output Type, Package.
TS3702CDT
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TS3702IDT
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TS3702CD
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←LM393
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LMV393
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
TS3702ID الحدود القصوى والخصائص الكهربائية
| Number of Comparators | 2 |
| Comparator Type | General purpose voltage comparator |
| Supply Voltage Range (Single) | 2.7 V to 16 V |
| Supply Voltage Range (Dual) | +/-1.35 V to +/-8 V |
| Supply Current per Comparator | 9 uA typical |
| Input Impedance | 10^12 ohm typical |
| Input Offset Current | 1 pA typical |
| Response Time | 2.3 us typical |
| نوع الخرج | Push-pull CMOS |
| External Pull-up Resistor Required | No |
| Input Common-Mode Range | Includes GND |
| LM393 Compatibility | Pin-to-pin and functionally compatible with bipolar LM393 |
| نطاق درجة حرارة التشغيل | -40 C to +125 C |
| العلبة | 8-pin SOIC-8 (SO-8), surface mount |
| Marking Code | 3702I |
تكوين أطراف TS3702ID
| دبوس 1 | OUT1 — Comparator 1 output, push-pull CMOS |
| دبوس 2 | IN1- — Comparator 1 inverting input |
| دبوس 3 | IN1+ — Comparator 1 non-inverting input |
| دبوس 4 | V- — Negative supply / ground reference pin |
| دبوس 5 | IN2+ — Comparator 2 non-inverting input |
| دبوس 6 | IN2- — Comparator 2 inverting input |
| دبوس 7 | OUT2 — Comparator 2 output, push-pull CMOS |
| دبوس 8 | V+ — Positive supply pin |
التطبيقات النموذجية
TS3702ID مناسب لـ 6 التطبيقs: Battery Threshold Monitoring, Window Comparator for Over/Undervoltage, Portable Instrument Sensor Conditioning, Industrial Level and Limit Detection, Battery Charger and Power Path Cutoff, Automotive and Off-Highway Sensing Node.
Battery Threshold Monitoring
The TS3702ID suits low-power battery supervision because each channel draws only 9 uA typical while presenting a 10^12 ohm input impedance that does not load the cell voltage divider. A resistive divider feeding IN+ and the reference on IN- gives a window or simple threshold detector whose trip point drifts only with resistor tolerance and temperature, since the 1 pA typical input offset current barely loads the sensing network. With the push-pull CMOS output the alarm signal drives a microcontroller input directly, no external pull-up resistor and no continuous bias current is needed, which helps extend the service interval of the powered node compared with an open-collector LM393 arrangement using a permanently biased resistor.
موصى به
Window Comparator for Over/Undervoltage
Using the two independent channels of the TS3702ID as a window detector allows one 8-pin SOIC-8 to signal both overvoltage and undervoltage on a rail. The two channels share the same supply pins, so the whole detector adds about 18 uA of load regardless of rail voltage, and the operating range of 2.7 V to 16 V single supply or +/-1.35 V to +/-8 V dual supply lets the same part monitor a regulated 5 V rail or a +/-12 V analog node. The 2.3 us typical response time is short enough to trip before the protected rail leaves tolerance, and the push-pull output means the fault signal is a valid CMOS level with no pull-up resistor and no added quiescent current.
موصى به
Portable Instrument Sensor Conditioning
In handheld and wearable measurement equipment the TS3702ID converts a small sensor differential into a logic decision with almost no standing current cost. The 10^12 ohm typical input impedance means the transducer bridge or resistive ladder is barely loaded, so the threshold setpoint stays accurate, and the 1 pA typical input offset current keeps the input bias error below the resolution of most low-cost sensors. Because the device operates from 2.7 V, it fits single-cell powered designs, and the wide -40 C to +125 C rating covers products that are specified for both consumer and industrial environments. The push-pull output drives the display or radio control line without the extra resistor an open-collector part would demand.
موصى به
Industrial Level and Limit Detection
The TS3702ID works well as a limit detector on tanks, pipes and machine tools where a sensor output must be turned into a discrete event. Its 2.3 us typical response time and push-pull CMOS output give fast, valid logic levels that can drive a PLC input or a safety relay stage without level-shifting, and the industrial -40 C to +125 C grade keeps behaviour predictable in unheated cabinets and outdoor enclosures. Because the input common-mode range includes ground, sensor outputs referenced to 0 V can be compared directly, and the extremely high input impedance allows long sensor wiring without the comparator biasing the line.
موصى به
Battery Charger and Power Path Cutoff
In charger and power-path designs the TS3702ID provides a fast, low-current cutoff decision on the battery terminal. The 9 uA typical per comparator is small enough not to distort the standby current budget of a charger module, while the 2.7 V minimum single supply allows the comparator to stay active across the useful cell range. When the fast response time of 2.3 us detects an out-of-window condition, the push-pull output directly enables or disables the next stage in the chain. Because the output actively sources and sinks, the same footprint works with CMOS control logic and with the level-shifting arrangements common in automotive and industrial power modules.
موصى به
Automotive and Off-Highway Sensing Node
The TS3702ID suits off-highway and body electronics sensing nodes where a wide ambient range and low standby current both matter. The -40 C to +125 C operating range tolerates engine bay and unheated body compartment temperatures, and the 9 uA per comparator keeps the quiescent draw of a parked vehicle node low enough for the battery to survive long storage periods. The push-pull CMOS output gives a clean logic signal into the body network transceiver, avoiding the pull-up resistor and its associated current that an open-collector LM393 substitute would require. Its pin compatibility with the LM393 footprint also eases reuse of existing board spares.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ TS3702ID — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | TS3702CDT | TS3702IDT | TS3702CD | LM393 | LMV393 |
|---|---|---|---|---|---|---|
| Package | SOIC-8 (SO-8) | SOIC-8 (SO-8) - same footprint | SOIC-8 (SO-8) - same footprint | SOIC-8 (SO-8) - same footprint | SOIC-8 (SO-8) - same LM393 pinout | SOIC-8 (SO-8) - same LM393 pinout |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments |
| Number of Comparators | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Push-pull CMOS (no pull-up resistor required) | Push-pull CMOS | Push-pull CMOS | Push-pull CMOS | Open collector, external pull-up required | Open collector, external pull-up required |
أبرز الفروقات
- Push-pull CMOS output removes the external pull-up resistor (مقابلLM393)
- Roughly twenty times lower supply current per channel (مقابلLM393)
- Higher input impedance and lower offset current for threshold accuracy (مقابلLMV393)
- Industrial temperature grade in the same SOIC-8 footprint (مقابلTS3702CDT)
ملاحظات التصميم
Do not add an external pull-up resistor to the TS3702ID output. The device uses a push-pull CMOS output stage, so an added pull-up simply wastes current and, in a push-pull stage, can create contention when the output drives low. Boards copied from an LM393 design may already carry that resistor; check the schematic before reusing an LM393 layout and confirm the output node in the TS3702 datasheet pin description table. If a pull-up must stay in the circuit for an open-collector-style downstream device, make sure the downstream input is high impedance.
Estimated: with both channels active at 9 uA each, the TS3702ID draws about 18 uA from the supply, so a 3 V cell with a 1000 uF reservoir would be depleted in roughly (3 V x 1000 uF)/(18 uA) = 167 hours if no other load exists. Use that figure as a sizing starting point, then add the load current of the logic that the comparator enables. Keep the supply decoupling close to pins 8 and 4, since a supply that sags as the output switches can shift the threshold during a transition.
The 10^12 ohm input impedance and 1 pA typical input offset current mean the threshold network must be designed for thermal stability rather than bias error. Keep the divider resistors at or below 1 M ohm so that leakage from board contamination, humidity and flux residue does not dominate the 1 pA bias, and place a 100 nF ceramic capacitor directly at the reference input to reject supply ripple that would otherwise modulate the trip point. Keep the sensor trace short and away from switching nodes, since the 2.3 us response time means fast transients are reproduced at the output.
Use the pin description table in the STMicroelectronics TS3702 datasheet to assign tracks on the 8-pin SOIC-8 footprint: OUT1, IN1-, IN1+, V-, IN2+, IN2-, OUT2 and V+. Place the two input networks so that each comparator's inverting and non-inverting pins are not adjacent to noisy switching pins of neighbouring circuitry, tie V- to the ground plane with a short direct connection, and route V+ through a local 100 nF capacitor to the plane. Because the part is pin-to-pin compatible with the LM393, keeping this layout discipline also makes an LM393-based respin possible without a board change.
معلومات الامتثال
The manufacturer datasheet and distributor listings confirm the device is a general-purpose industrial comparator with a -40 C to +125 C rating. Explicit RoHS, REACH, lead-free and halogen-free declarations were not identified for this exact MPN, so they are reported as unknown; check the STMicroelectronics product page for the current compliance statements before releasing a regulated design.