STMicroelectronics

TS556IDT - Dual CMOS Timer, 2.7MHz, SOIC-14 | STMicroelectronics

MPN: TS556IDT ✓ نشط
2 V to 16 V Vdss 220 uA at VCC = 5 V Id 14-pin SOIC Package 2.7 MHz Speed
الحد الأدنى للطلب: 1 |

TS556IDT نظرة عامة

The STMicroelectronics TS556IDT is a dual CMOS 555-type timer and oscillator designed for low-power timing, monostable, astable, and pulse-generation circuits. It provides a maximum astable operating frequency of 2.7 MHz, operates from a 2 V to 16 V supply, and is packaged in a 14-pin SOIC. The device is pin-to-pin and functionally compatible with bipolar NE556 timer families, while its CMOS implementation reduces supply-current demand and improves switching behavior in precision timing applications.

A 555 timer is a programmable time-delay and oscillator building block within the broader clock and timing IC category. Each TS556 timer section contains a voltage reference, comparators, a flip-flop, discharge transistor, and an output stage. The timing interval is set by external resistors and capacitors connected to the RC timing pins. Typical uses include delayed switching, pulse stretching, debounce circuits, lamp flashers, simple oscillators, and frequency dividers.

Key characteristics include a 2.7 MHz maximum astable frequency, a wide 2 V to 16 V operating supply range, and low power consumption. The manufacturer identifies the TS556 as a dual CMOS timer with typical supply current of 220 uA at VCC = 5 V, compared with approximately 6 mA for the NE556(a) bipolar family. The available technical description also identifies the TS556 as pin-to-pin and functionally compatible with bipolar NE556(a) devices.

The dual configuration allows two independent timing channels in one package, reducing component count and board area when an application needs simultaneous or complementary timing functions. The TS556IDT is suitable for industrial control, sensor interfaces, pulse generation, low-power instrumentation, embedded timing modules, and general-purpose oscillator circuits. Its SOIC-14 package supports conventional surface-mount assembly while retaining the familiar dual 555 interface.

When designing a replacement board, use the manufacturer pin-description table to preserve trigger, threshold, control-voltage, discharge, and output connections. Confirm the intended mode of operation and external RC network before changing timing components. The 2.7 MHz figure is a maximum astable-frequency capability, and actual operating frequency depends on resistor and capacitor values, load conditions, supply voltage, and timing tolerances. For systems requiring exact timing accuracy, evaluate the minimum and maximum RC values and the propagation behavior of the output stage over the intended voltage and temperature ranges.

This page combines the TS556IDT datasheet information, package details, timing-use context, and practical replacement guidance to support faster component selection and PCB-level integration.

بدائل مباشرة لـ TS556IDT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع TS556IDT (نفس عامل الشكل والبصمة) — يختلف في Operating Modes, Package.

STMicroelectronics
Operating Modes: Monostable and astable
Package: 14-SOIC
قارن مع TS556IDT →

TS556IDTTR

✅ بديل مباشر
📦 14-pin SOIC
Same TS556 dual CMOS timer and 2.7 MHz maximum astable frequency; ordering differs by tape-and-reel packaging, so the electrical match is identical.

📋 بديل مرجعي (غير موجود في الكتالوج)

TLC556IDR

✅ بديل مباشر
📦 14-pin SOIC
Dual timer in the same 14-pin SOIC outline, but the comparison lists a 2.1 MHz maximum frequency versus 2.7 MHz for TS556IDT, a 0.6 MHz or 22% lower rating.

📋 بديل مرجعي (غير موجود في الكتالوج)

TS556IDT المواصفات

Timer Configuration Dual 555-type timer
Maximum Astable Frequency 2.7 MHz
Supply Voltage Range 2 V to 16 V
Typical Supply Current 220 uA at VCC = 5 V
Low-Power Supply Current 180 uA typical at VCC = 3 V
NE556 Typical Supply Current 6 mA at VCC = 5 V
Operating Modes Astable and monostable
Technology CMOS
العلبة 14-pin SOIC
نوع التركيب Surface Mount
Pin Compatibility Pin-to-pin and functionally compatible with bipolar NE556(a)
حالة RoHS RoHS compliant
Lead-Free Status Lead-free
Timer Sections 2 independent channels

تكوين أطراف TS556IDT

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
دبوس 1 TRIGGER 1 — Trigger input for timer section 1
دبوس 2 OUTPUT 1 — Timer output for section 1
دبوس 3 OUTPUT 2 — Timer output for section 2
دبوس 4 RESET 1 — Reset input for timer section 1
دبوس 5 CONTROL VOLTAGE 1 — Control-voltage input for timer section 1
دبوس 6 THRESHOLD 1 — Threshold input for timer section 1
دبوس 7 DISCHARGE 1 — Discharge output for timer section 1
دبوس 8 TRIGGER 2 — Trigger input for timer section 2
دبوس 9 OUTPUT 2 — Timer output for section 2
دبوس 10 RESET 2 — Reset input for timer section 2
دبوس 11 CONTROL VOLTAGE 2 — Control-voltage input for timer section 2
دبوس 12 THRESHOLD 2 — Threshold input for timer section 2
دبوس 13 DISCHARGE 2 — Discharge output for timer section 2
دبوس 14 VCC — Positive supply voltage
دبوس 15 GND — Ground reference

التطبيقات النموذجية

TS556IDT مناسب لـ 6 التطبيقs: Low-Power Astable Oscillator, Monostable Pulse Generator, Delay and Debounce Circuit, Industrial Control Pulse Module, Frequency Divider and Tone Generator, Battery-Powered Instrumentation.

⚡

Low-Power Astable Oscillator

The TS556IDT is well suited to a low-power astable oscillator because each channel can generate a repetitive waveform using external resistors and capacitors. Its dual CMOS timer architecture supports supply voltages from 2 V to 16 V, while typical consumption is listed as 220 uA at 5 V. The 2.7 MHz maximum astable frequency provides substantial timing range, from low-frequency clock-like waveforms to higher-frequency signal generation. Design the RC network around the manufacturer’s recommended component limits and verify frequency tolerance, duty cycle, and output loading over the intended voltage and temperature range.

🧩

Monostable Pulse Generator

A TS556IDT channel can be configured as a monostable timer to produce a fixed-duration pulse after a trigger event. The internal comparator, flip-flop, discharge transistor, and output stage implement the timing sequence, while external resistors and capacitors establish the pulse interval. The 2 V minimum supply allows operation in compact low-voltage systems, and the dual arrangement permits a second independent pulse function. When substituting into an existing circuit, preserve trigger and threshold levels and validate output pulse width against the intended minimum and maximum RC values.

🔧

Delay and Debounce Circuit

The TS556IDT can implement delay and contact-debounce functions in sensor, control-panel, and switch-interface circuits. A trigger starts the timing interval, and the timer output changes state after the programmed RC delay. Low CMOS supply current is valuable in battery-operated equipment, particularly when the timer is active only intermittently. Use the dual channels when separate delays or a complementary output relationship is needed, and check the output rise and fall timing at the logic family connected to the timer.

🏭

Industrial Control Pulse Module

In industrial control equipment, the TS556IDT can generate repeatable timing pulses for actuator sequencing, watchdog-like delays, or periodic control events. Its 2 V to 16 V supply range supports multiple embedded control architectures, while the dual timer channels can reduce component count by combining two timing functions in one 14-pin SOIC. For industrial deployments, check temperature limits, output current, supply-current spikes during transitions, and timing tolerances before finalizing the external component values and protection strategy.

📺

Frequency Divider and Tone Generator

The TS556IDT can generate a periodic clock and divide that frequency into a lower useful timing signal for counters, display systems, or sequencing logic. Its maximum astable frequency of 2.7 MHz gives designers headroom above many low-speed timing requirements, while the 2 V to 16 V operating range supports different logic environments. Verify the output duty cycle and propagation behavior at the target frequency, and use the second timer channel when a separate delay, tone, or modulation function is required.

🖥️

Battery-Powered Instrumentation

The TS556IDT is appropriate for portable measurement or instrumentation modules where continuous timer operation must not dominate the power budget. The manufacturer lists typical supply current of 220 uA at 5 V for the TS556, materially below the 6 mA figure cited for NE556(a), and the timer operates down to 2 V. Use the device for low-duty-cycle sample timing, delayed acquisition, or periodic sensor stimulation. Confirm battery voltage range, leakage through external timing components, and the idle current of the complete instrument rather than the timer alone.

What is the TS556IDT used for?
The TS556IDT is a dual CMOS 555-type timer used for monostable pulse generation, astable oscillation, delays, debounce, and frequency-related circuits. Each channel uses external resistors and capacitors to set its timing interval. According to the STMicroelectronics TS556 product information, the device combines two independent timer sections in a 14-pin SOIC package and supports a maximum astable frequency of 2.7 MHz.
What is the operating voltage of TS556IDT?
The TS556IDT operates from 2 V to 16 V, as stated in the TS556 technical description. This wide supply range allows the timer to operate from low-voltage logic systems as well as higher-voltage industrial control circuits. The manufacturer also identifies typical supply current of 220 uA at VCC = 5 V, making the device suitable for low-power timing and oscillator designs.
Where can I download the TS556IDT datasheet PDF?
The TS556IDT datasheet PDF is available through the STMicroelectronics TS556 product page and the Datasheets.com TS556IDT datasheet listing. Use the manufacturer datasheet for the definitive pin descriptions, electrical limits, timing characteristics, and application examples. The verified TS556 technical information identifies the device as a 14-pin SOIC dual CMOS timer with a 2 V to 16 V supply range.
Where can I find the TS556IDT pinout?
Use the pin-description table in the manufacturer TS556 datasheet to locate the TS556IDT pinout and assign PCB tracks. The device uses the standard dual-555 organization in a 14-pin SOIC: two trigger inputs, two threshold inputs, two control-voltage inputs, two discharge outputs, two timer outputs, ground, and supply. The exact electrical descriptions and any no-connect conditions should be taken from the TS556 datasheet.
What is the maximum frequency of TS556IDT?
The TS556IDT has a maximum astable operating frequency of 2.7 MHz. This rating describes the timer family’s capability under the manufacturer’s specified operating conditions, not a guaranteed operating frequency for every external RC network. Actual frequency depends on the selected resistors and capacitors, supply voltage, load, temperature, and the permitted timing-component ranges.
How much current does TS556IDT consume?
The TS556IDT has a typical supply current of 220 uA at VCC = 5 V according to the STMicroelectronics product information. A related technical description lists 180 uA typical at VCC = 3 V. These CMOS figures are substantially lower than the approximately 6 mA typical current cited for bipolar NE556(a) devices, supporting battery-powered and low-energy timer applications.
Is TS556IDT pin compatible with NE556?
Yes, the TS556 technical information identifies the device as pin-to-pin and functionally compatible with bipolar NE556(a) devices. This compatibility allows an existing 14-pin timer layout to be evaluated for a TS556IDT substitution when the supply, timing tolerances, output loading, and temperature requirements remain acceptable. Verify the exact manufacturer pin table and electrical conditions before releasing a replacement design.
What is the difference between TS556IDT and TLC556IDR?
The TS556IDT and TLC556IDR are both 14-pin dual timer devices intended for 555-style timing applications, but their manufacturer specifications differ. The verified comparison data identifies TLC556CD as a 2.1 MHz timer, while TS556IDT is specified up to 2.7 MHz. Confirm supply voltage, frequency, timing accuracy, and output behavior against the relevant datasheets before treating either device as a drop-in replacement.
Can TS556IDT replace NE556D?
The TS556IDT can be considered for NE556D replacement only when the PCB footprint, supply range, timing accuracy, output current, temperature range, and output polarity meet the system requirements. The TS556 is functionally compatible with bipolar NE556(a) families, but the verified material does not establish that every NE556D package variant is interchangeable with the TS556IDT SOIC package. Compare the manufacturer pinouts and verify the solder footprint.
What is the best drop-in replacement for TS556IDT?
The closest same-family drop-in candidate identified in the verified cross-reference material is TS556IDTTR, which uses the same TS556 dual CMOS timer and 14-pin SOIC footprint but differs in tape-and-reel ordering. It is not a materially different electrical alternative. Other candidates such as TLC556IDR have different manufacturer-specific specifications, so verify timing and electrical limits rather than assuming interchangeability.
When should I choose TS556IDT instead of a bipolar NE556?
Choose TS556IDT when low supply current, CMOS operation, and operation down to a 2 V supply are more important than using a legacy bipolar NE556 implementation. The manufacturer lists typical supply current of 220 uA at 5 V for TS556 compared with 6 mA for NE556(a), while retaining functional compatibility with the familiar dual-555 architecture. Account for any differences in timing tolerance, output behavior, and exact package variant.
Is TS556IDT suitable for low-power oscillator circuits?
Yes, the TS556IDT is suitable for low-power oscillator circuits because it is a CMOS dual timer with a wide 2 V to 16 V operating range and low typical supply current. The device supports astable operation with a maximum specified frequency of 2.7 MHz. For a practical oscillator, select RC components within the manufacturer’s recommended limits and check output duty-cycle, frequency tolerance, and load behavior across voltage and temperature.
Where can I buy TS556IDT and check its lead time?
Use the Request a Quote form on this page to ask about TS556IDT availability, current lead time, minimum order quantity, and shipment options. The verified listings confirm the exact MPN and package, but they do not provide a stable quantity-break price table for this configuration. A current quotation is therefore required for transactional planning.
What is the price of TS556IDT?
The current TS556IDT price depends on order quantity, supply status, and the purchasing channel, so request a quote through the Request a Quote form on this page. The verified listings include the exact TS556IDT part number and identify it as a 14-pin SOIC device, but they do not contain a usable quantity-break table that can be reproduced as a stable price table.
What are the key specifications of TS556IDT?
The key TS556IDT specifications are dual 555-type operation, a maximum astable frequency of 2.7 MHz, a 2 V to 16 V supply range, and 220 uA typical supply current at 5 V. The device is manufactured by STMicroelectronics in a 14-pin SOIC package and is described as pin-to-pin and functionally compatible with bipolar NE556(a) timers. These figures establish its core use in low-power timing and oscillator designs.

بيانات مرجعية هندسية لـ TS556IDT — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the TS556IDT for new designs that need two 555-style timing channels, low CMOS supply current, operation from 2 V to 16 V, and relatively high astable-frequency capability. TS556IDTTR is the closest same-family option when the exact ordering format or reel presentation is preferred, with no intended electrical trade-off. Consider TLC556IDR when a Texas Instruments dual timer is preferred and the lower 2.1 MHz maximum-frequency rating still satisfies the application. A bipolar NE556 remains an option for legacy systems that specifically rely on its established electrical characteristics, but the TS556 typically consumes substantially less supply current. In every replacement, confirm the exact package footprint, pinout, timing tolerances, output loading, reset behavior, and temperature limits before production release.

المقارنة مع البدائل

المعامل هذا المنتج TS556IDTTR TLC556IDR
Package 14-pin SOIC 14-pin SOIC - same 14-pin SOIC - same
Brand STMicroelectronics STMicroelectronics Texas Instruments
Timer Configuration Dual 555-type timer Dual CMOS timer Dual timer
Maximum Astable Frequency 2.7 MHz 2.7 MHz 2.1 MHz
Minimum Supply Voltage 2 V 2 V 2 V
Technology CMOS CMOS CMOS
Packing Tape and reel Tape and reel Tape and reel

أبرز الفروقات

  • Higher specified maximum astable frequency (مقابلTLC556IDR)
  • Lower typical supply current at 5 V (مقابلNE556)
  • Same-family electrical identity (مقابلTS556IDTTR)

ملاحظات التصميم

Place the external timing resistor and capacitor close to the relevant DISCHARGE, THRESHOLD, and TRIGGER pins to limit parasitic capacitance and resistance. Keep the two timer channels physically separated where one channel drives a sensitive analog or timing input. Confirm the package footprint and pin-1 orientation against the manufacturer drawing before layout release.

Route the supply and ground pins directly to the device and provide local high-frequency bypass capacitance. Although the TS556 has low typical supply current, output transitions can create supply-current spikes, particularly when driving capacitive loads or long PCB traces. Decouple each timer section according to the manufacturer application guidance and avoid routing timing outputs near sensitive high-impedance nodes.

Do not treat the 2.7 MHz maximum as an unconditional operating point. The actual astable frequency depends on the RC network, supply voltage, temperature, and load. Before using TS556IDT as a drop-in substitute for a bipolar NE556, verify pin connectivity, output polarity, timing tolerance, output-current capability, and maximum frequency. The TS556 is described as NE556(a)-compatible, but the exact circuit still requires validation.

The trigger and threshold inputs are timing-sensitive nodes. Avoid long traces, unnecessary vias, and capacitive loading near these pins, especially at higher astable frequencies. If an external signal must drive TRIGGER, use a source impedance and edge rate compatible with the device input and ground-return current through the same reference network. Check pulse-width behavior and output timing over the intended supply range.

معلومات الامتثال

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Yes
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The verified comparison material identifies TS556IDTTR as RoHS compliant with an Ecopack3 designation. Other compliance attributes were not established for the exact TS556IDT orderable part.

تم التحقق من البيانات في: 2026-11-10 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

TS556IDT datasheet TS556IDT pinout TS556IDT datasheet pdf TS556IDT equivalent TS556IDT replacement TS556IDT cross reference TS556IDT vs TLC556IDR TS556IDT SOIC-14 pinout TS556IDT oscillator circuit STMicroelectronics TS556IDT TS556IDT price TS556IDT stock

المكونات والمصطلحات ذات الصلة

STMicroelectronics TS556IDT TS556IDTTR TLC556IDR NE556 TS556 555 timer dual CMOS timer clock and timing IC programmable timer oscillator monostable multivibrator astable multivibrator astable frequency supply current pin-to-pin compatible SOIC-14 SOIC family surface-mount package external RC timing network trigger input threshold input discharge output RoHS
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر