A3P060-1TQ144 - 60K Gate ProASIC3 FPGA | Microchip Technology
MPN: A3P060-1TQ144 ✓ نشطA3P060-1TQ144 نظرة عامة
A ProASIC3 FPGA is a reprogrammable semiconductor that combines configurable logic blocks, programmable interconnect, embedded SRAM, and user I/O in one integrated device. Within the product hierarchy, it sits between a programmable logic device and a field-programmable gate array, offering substantially greater capacity than simple programmable logic while retaining nonvolatile configuration and a relatively low total cost of ownership.
The A3P060-1TQ144 provides 60000 system gates across 1536 logic blocks and supports a listed operating frequency of 272 MHz. Its 1.5 V core voltage reduces power requirements compared with older FPGA architectures, while the 144-pin TQFP package provides 91 user I/O according to the distributor product listing. The device is manufactured on 130 nm CMOS technology and uses a 0.5 mm pin pitch in a 20 mm by 20 mm package.
The programmable architecture supports parallel logic implementation, embedded memory, control functions, and external interface logic in one device. Configuration storage allows the same board design to be reprogrammed for firmware revisions, field updates, or design corrections without replacing the component. The combination of 1536 logic blocks, 18432 bits of SRAM, and 91 I/O makes the A3P060 suitable for control logic, protocol bridging, data acquisition, and low-to-medium complexity digital signal processing.
Typical uses include industrial factory automation, networked monitoring equipment, motor and motion control, embedded communications gateways, and compact control panels. The 144-lead TQFP package also suits prototype and production boards where a leaded package simplifies inspection, rework, and manual assembly compared with fine-pitch BGA or QFN options.
When laying out a PCB, treat all I/O and power pins according to the manufacturer pin-description table, and route configuration, clock, and serial programming signals away from high-speed outputs where possible. The 1.5 V core and I/O supply requirements are not interchangeable, so power planning must follow the exact voltage and decoupling recommendations in the ProASIC3 family documentation.
This page combines ProASIC3 family specifications with practical package-planning guidance, speed- and temperature-grade alternatives, and an engineering comparison of compatible 144-lead devices. It is intended to accelerate component selection, PCB footprint planning, and qualification for compact FPGA-based control systems.
بدائل مباشرة لـ A3P060-1TQ144 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع A3P060-1TQ144 (نفس عامل الشكل والبصمة) — يختلف في System Gates.
A3P060-TQ144
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←A3P060-TQG144
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
A3P060-1TQG144
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
A3P060-1TQG144I
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
A3P060-1TQ144Y
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
A3P060-1TQ144 الحدود القصوى والخصائص الكهربائية
| Device Type | ProASIC3 field-programmable gate array (FPGA) |
| System Gates | 60000 gates |
| Configurable Logic Blocks | 1536 CLBs |
| Embedded SRAM | 18432 bits |
| User I/O | 91 I/O |
| Maximum Frequency | 272 MHz |
| Core Supply Voltage | 1.5 V |
| Process Technology | 130 nm CMOS |
| Package Type | TQFP-144 |
| عدد الأطراف | 144 pins |
| Package Dimensions | 20 mm x 20 mm |
| Package Height | 1.40 mm |
| Pin Pitch | 0.50 mm |
| Programming | Nonvolatile FPGA configuration |
| Logic Family | CMOS |
| نوع التركيب | Surface mount |
دليل تكوين أطراف A3P060-1TQ144 1.40 mm
تكوين الأطراف لـ A3P060-1TQ144 (حزمة 1.40 mm). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ A3P060-1TQ144.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
A3P060-1TQ144 مناسب لـ 6 التطبيقs: Industrial Factory Automation Controllers, Motor Drive and Motion Control Logic, Data Acquisition and Signal Conditioning, Embedded Communications Gateways, Smart Sensor and Monitoring Nodes, Programmable Logic and Test Equipment.
Industrial Factory Automation Controllers
The A3P060-1TQ144 fits machine-control and factory-automation logic that requires 1536 configurable logic blocks, 91 user I/O, and moderate embedded data storage in one programmable device. Its 60000 system gates can host sequencers, interlock logic, status machines, and communication interfaces without relying on a separate microcontroller for every task. The 1.5 V core reduces supply requirements, while the 144-lead TQFP provides a generous I/O count for limit switches, encoders, solenoid drivers, and operator interfaces. For equipment operating across an extended industrial temperature range, specify the industrial-grade A3P060-1TQG144I ordering option and verify its timing and qualification data.
موصى به
Motor Drive and Motion Control Logic
The A3P060-1TQ144 is suitable for the digital control layer of a motor-drive or motion-control system because 1536 logic blocks can implement pulse-width modulation, direction sequencing, fault capture, and position-decoding functions. Its 91 user I/O allow encoder channels, Hall-effect sensors, brake controls, and status signals to be consolidated in one package, while 18432 bits of embedded SRAM can buffer motion commands and diagnostic history. The 272 MHz listed operating frequency supports high-speed control logic, although motor timing must still be checked against the family datasheet. Use the manufacturer pin-description table for every I/O assignment and isolate switching-node signals from sensitive control inputs.
موصى به
Data Acquisition and Signal Conditioning
The A3P060-1TQ144 can implement digital filtering, decimation, trigger control, and data packing for compact acquisition systems. The device provides 60000 system gates and 18432 bits of SRAM, which support parallel filtering pipelines and short capture buffers while leaving external memory available for larger records. With 91 user I/O, the FPGA can connect directly to multiple converter outputs, latch control signals, and communication transceivers without a separate glue-logic device. The 1.5 V core and 130 nm CMOS process fit low-power embedded instrumentation, but analog input bandwidth, output timing, and I/O voltage standards must be validated against the specific system architecture.
موصى به
Embedded Communications Gateways
The A3P060-1TQ144 is appropriate for protocol conversion, framing, buffering, and supervisory logic in embedded communications equipment. Its 60000-gate ProASIC3 architecture can run parallel state machines for serial links, Ethernet or fieldbus framing, and host-interface translation, while the 18432 bits of SRAM provide packet buffering and command queues. The 91-I/O count simplifies simultaneous use of multiple serial ports, indicator outputs, and configuration signals. A 144-lead TQFP also supports prototype boards and maintenance-friendly assemblies where fine-pitch BGA inspection would be difficult. Verify supported I/O standards, clocking requirements, and configuration interface signals in the family documentation.
موصى به
Smart Sensor and Monitoring Nodes
The A3P060-1TQ144 suits compact monitoring nodes that must acquire several sensor outputs, apply local filtering, and forward results over a serial link. The 91 user I/O provide capacity for digital sensors, threshold inputs, alarm outputs, and status indicators, while the embedded SRAM can hold recent samples or a rolling diagnostic buffer. Its reprogrammability allows sensor thresholds, scaling coefficients, and communication mappings to be revised without changing the PCB. The device is particularly useful where a fixed-function microcontroller would require additional external logic for acquisition, timing, or protocol handling. Confirm the operating-temperature grade and the exact I/O voltage requirements for each connected sensor.
موصى به
Programmable Logic and Test Equipment
The A3P060-1TQ144 can implement custom test sequences, stimulus generation, timing checks, and result logging in programmable test and measurement equipment. Its 1536 logic blocks are well suited to parallel pattern generation, while 91 I/O provide multiple channels for device-under-test control and response capture. The 18432 bits of embedded SRAM can hold test vectors or measurement records, and the 272 MHz listed operating frequency supports moderately fast digital test rates. The 144-lead TQFP package is convenient for laboratory prototypes and small production runs. Validate input thresholds, output drive, and timing margins against the test fixture and the manufacturer electrical characteristics.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ A3P060-1TQ144 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | A3P060-TQ144 | A3P060-TQG144 | A3P060-1TQG144 | A3P060-1TQG144I | A3P060-1TQ144Y |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-144 | TQFP-144 - same footprint | TQFP-144 - same footprint | TQFP-144 - same footprint | TQFP-144 - same footprint | TQFP-144 - same footprint |
| FPGA Family | ProASIC3 | ProASIC3 | ProASIC3 | ProASIC3 | ProASIC3 | ProASIC3 |
| System Gates | 60000 gates | 60000 gates | 60000 gates | 60000 gates | 60000 gates | 60000 gates |
| Configurable Logic Blocks | 1536 CLBs | 1536 CLBs | 1536 CLBs | 1536 CLBs | 1536 CLBs | 1536 CLBs |
| User I/O | 91 I/O | 91 I/O | 91 I/O | 91 I/O | 91 I/O | 91 I/O |
| Core Voltage | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V |
| Process Technology | 130 nm CMOS | 130 nm CMOS | 130 nm CMOS | 130 nm CMOS | 130 nm CMOS | 130 nm CMOS |
| Ordering Grade | 1TQ144 - speed-grade 1 ordering code | Standard TQ144 ordering grade | TQG144 ordering grade | Speed-grade 1 TQG144 ordering grade | Speed-grade 1 industrial TQG144I ordering grade | Speed-grade 1 TQ144Y ordering grade |
أبرز الفروقات
- Provides a 91-I/O 144-lead option within the compact ProASIC3 family (مقابلA3P060-VQG100)
- Uses a leaded 0.50 mm-pitch TQFP for inspection and prototype assembly (مقابلA3P060-FGG144T)
- Combines 60000 gates, 1536 CLBs, and 18432 bits of SRAM in one device (مقابلA3P060-1TQG144I)
ملاحظات التصميم
Treat the 1.5 V core rail separately from the device I/O supplies and configuration supply. Follow the ProASIC3 family recommended-decoupling network, including the specified bulk and high-frequency capacitors placed close to their corresponding pins. Check the load current for every external I/O rather than assuming the 91 available I/O can drive maximum current simultaneously. Sequencing must follow the family power-up requirements so configuration inputs remain in a defined state during ramp-up.
Use the 144-lead TQFP package drawing for land-pattern generation: a 20 mm by 20 mm body, 0.50 mm pitch, and 1.40 mm listed height. Keep configuration and serial-programming traces away from high-speed outputs and switching-node inputs. Route sensitive clock and differential-interface signals over a continuous ground plane, and avoid placing noisy power-converter routing directly beneath the FPGA. Thermal performance in the leaded package is predictable but still depends on copper area and airflow.
Assign pins from the manufacturer pin-description table rather than from an older A3P060 board or another package. A3P060-VQG100 and A3P060-FGG144 alternatives have different footprints and cannot share this PCB without redesign. Preserve configuration access and design a test path for JTAG or the selected programming interface so a board can be diagnosed after assembly.
Do not substitute the A3P060-VQG100 or A3P060-FGG144 families as drop-in parts because their package dimensions and pin arrangements differ. When changing among 144-lead order codes, compare speed grade, temperature grade, qualification, supply voltage, and I/O standard in the Microchip ordering documentation. The trailing Y and I suffixes are meaningful ordering information, not cosmetic production codes.
معلومات الامتثال
Compliance status must be confirmed for the exact A3P060-1TQ144 ordering code. Automotive qualification is not established for this standard ordering code; the A3P060-1TQG144I industrial ordering option is a separate grade.