Analog Devices

AD504SH - 300 kHz Precision Op Amp | Analog Devices

MPN: AD504SH ✗ انتهى عمره الإنتاجي
500 uV Vdss 1.5 mA Id TO-99-8 (CBCY8), hermetically sealed Package
الحد الأدنى للطلب: 1 |

AD504SH نظرة عامة

Analog Devices AD504SH is an obsolete, single-amplifier precision operational amplifier with a maximum offset voltage of 500 uV, nominal unity-gain bandwidth of 300 kHz, and nominal common-mode rejection ratio of 120 dB. It is packaged in an hermetically sealed, round TO-99-8 metal-can package with eight wire terminals. The operating temperature range extends from -55 C to +125 C, supporting military and industrial signal-conditioning equipment.

An operational amplifier is a voltage-feedback amplifier that uses differential input voltage to control an output voltage. The AD504SH belongs to the general-purpose operational-amplifier hierarchy, where precision offset, common-mode rejection, low supply current, and stable unity-gain behavior are important for sensors, instrumentation, and low-level analog signals. Its 1.5 mA supply-current specification places it in the low-power segment of the AD504 family.

The most prominent characteristics are the 300 kHz unity-gain bandwidth, 120 dB nominal common-mode rejection ratio, 500 uV maximum input offset voltage, and approximately 25 mA typical output-current capability. These ratings make the device suitable for signal paths requiring moderate bandwidth rather than high-speed waveform processing. The 120 dB CMRR helps reject common-mode interference, while the offset limit supports precision measurements when appropriately calibrated.

The AD504SH uses a conventional eight-terminal metal-can package and is listed with bipolar input characteristics. Its 300 kHz nominal unity-gain bandwidth is suitable for low-frequency precision loops and moderate-bandwidth signal amplification. Because the device is obsolete and specified in a hermetically sealed TO-99-8 package, it is principally relevant to maintenance, repair, and legacy-system replication rather than new high-volume surface-mount designs.

Typical uses include bridge-amplifier interfaces for resistive sensors, precision current measurement, low-level instrumentation, data acquisition front ends, and military-grade test equipment. In these applications, the AD504SH can amplify a small differential signal while rejecting common-mode voltage and limiting the bias current drawn from the supply. The -55 C to +125 C temperature range supports harsh environmental equipment when appropriate derating and screening are used.

Designers should follow the manufacturer's obsolete datasheet for the complete pin description, supply limits, electrical characteristics, and military qualification information. Stable operation requires adequate supply voltage, suitable output-voltage headroom, and decoupling close to the supply terminals. Existing TO-99 layouts must preserve the original lead numbering and metal-can orientation because the package is not surface mount.

This product page consolidates the obsolete-product status, key electrical ratings, package details, sourcing information, and documented AD504 family alternatives. It also distinguishes the standard AD504SH from screened AD504SH/883 and AD504SH/883B variants so engineers can select a replacement or heritage-order component without changing the TO-99-8 footprint.

بدائل مباشرة لـ AD504SH — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

AD504SH/883

✅ بديل مباشر
📦 TO-99-8 (CBCY8)
Retains 500 uV maximum offset, 300 kHz nominal bandwidth, and 120 dB nominal CMRR; adds the /883 screened or qualified ordering designation

📋 بديل مرجعي (غير موجود في الكتالوج)

AD504SH/883B

✅ بديل مباشر
📦 TO-99-8 (CBCY8)
Retains 500 uV maximum offset, 300 kHz nominal bandwidth, 120 dB nominal CMRR, and 125 C maximum temperature; differs by the /883B qualification revision

📋 بديل مرجعي (غير موجود في الكتالوج)

AD504SH الحدود القصوى والخصائص الكهربائية

Amplifier Type Single general-purpose operational amplifier
Number of Circuits 1 circuit
Maximum Input Offset Voltage 500 uV
Nominal Unity-Gain Bandwidth 300 kHz
Nominal Common-Mode Rejection Ratio 120 dB
Maximum Operating Temperature 125 C
Minimum Operating Temperature -55 C
تيار التغذية 1.5 mA
Typical Output Current 25 mA
Input Technology Bipolar
العلبة TO-99-8 (CBCY8), hermetically sealed
Package Shape Round
Number of Terminals 8
Terminal Form Wire
نوع التركيب Through-hole
Temperature Grade Military
حالة دورة الحياة Obsolete
AEC-Q100 Qualification Not applicable

دليل تكوين أطراف AD504SH round

تكوين الأطراف لـ AD504SH (حزمة round). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة round لـ AD504SH

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ AD504SH.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

AD504SH مناسب لـ 6 التطبيقs: Precision Bridge Sensor Interface, Low-Level Instrumentation Amplification, Military Legacy Signal Conditioning, Precision Current Measurement, Industrial Process Signal Conditioning, Laboratory Reference Signal Conditioning.

🧩

Precision Bridge Sensor Interface

The AD504SH fits low-level bridge-sensor front ends where a 500 uV maximum offset limit, 120 dB nominal common-mode rejection ratio, and 300 kHz unity-gain bandwidth are sufficient. Its 1.5 mA supply current also helps limit the amplifier's contribution to a portable or distributed measurement system. Place the device in an instrumentation configuration with matched resistors and verify input bias current, offset drift, and common-mode limits for the selected sensor. Because AD504SH is obsolete, new designs should preserve the TO-99-8 footprint only when maintaining an existing platform or building a controlled heritage assembly.

📟

Low-Level Instrumentation Amplification

AD504SH is suitable for instrumentation circuits that amplify small differential signals while rejecting common-mode interference. Its nominal 120 dB common-mode rejection ratio and 500 uV maximum input offset voltage provide the principal selection criteria, while the 300 kHz bandwidth supports moderate-frequency measurement channels rather than very fast data-acquisition systems. The 25 mA typical output-current rating gives adequate drive for many analog stages and external bias networks. Confirm supply polarity, output swing, and input common-mode range against the AD504 datasheet before committing the amplifier to a laboratory or industrial measurement chain.

✈️

Military Legacy Signal Conditioning

The hermetically sealed TO-99-8 AD504SH is relevant to legacy military signal-conditioning modules that were designed around a 300 kHz precision amplifier with 500 uV maximum offset. Its -55 C to +125 C operating range and military temperature grade support environmental requirements when the complete circuit, screening process, and qualification documentation are appropriate. The AD504SH/883 and AD504SH/883B designations offer documented family alternatives for screened or qualified maintenance. Engineers should compare lot-control, screening, test-temperature, and certificate requirements rather than relying on electrical similarity alone.

⚡

Precision Current Measurement

AD504SH can amplify the voltage generated by a current-sense element when the required signal bandwidth remains below the amplifier's 300 kHz nominal unity-gain bandwidth. Its maximum input offset voltage of 500 uV sets an important floor for current-sense resolution, while the 120 dB nominal common-mode rejection ratio helps when the sense element sits near a larger supply-derived voltage. The 1.5 mA supply current can reduce loading in compact monitoring systems. A practical design must also check input bias current, common-mode range, supply voltage, and output saturation before selecting this obsolete device.

🏭

Industrial Process Signal Conditioning

The AD504SH is applicable to legacy industrial process-control modules that condition low-level analog signals and require a wide -55 C to +125 C temperature range. Its 120 dB nominal common-mode rejection ratio is useful when the input includes substantial system noise, while the 300 kHz bandwidth covers many pressure, temperature, and position sensing loops without requiring a high-speed amplifier. The TO-99-8 through-hole package remains useful for rugged repairable assemblies, although it consumes more board area than modern surface-mount devices. Verify long-term offset drift and input bias-current behavior for each production or maintenance build.

🔬

Laboratory Reference Signal Conditioning

AD504SH can be used in laboratory signal-conditioning modules where a low 1.5 mA supply current and 120 dB nominal common-mode rejection ratio are useful in compact measurement instruments. Its 300 kHz nominal unity-gain bandwidth accommodates low- and moderate-bandwidth analog signals but not precision waveform capture at megahertz rates. The 500 uV maximum offset specification should be included in the total error budget, along with bias current, drift, and resistor tolerances. For new instruments, evaluate modern alternatives first; for repairing an existing TO-99-8 board, the AD504 family remains the relevant source of electrical and package information.

ملخص المنتجات الموصى بها

AD504SH/883 Screened same-family maintenance option يُستخدم في: Precision Bridge Sensor Interface, Low-Level Instrumentation Amplification, Military Legacy Signal Conditioning, Precision Current Measurement, Industrial Process Signal Conditioning, Laboratory Reference Signal Conditioning AD504SH/883B Qualified family variant for legacy assemblies يُستخدم في: Precision Bridge Sensor Interface, Low-Level Instrumentation Amplification, Military Legacy Signal Conditioning, Precision Current Measurement, Industrial Process Signal Conditioning, Laboratory Reference Signal Conditioning
What is the operating voltage range of AD504SH?
The AD504SH operates from its specified positive and negative supply rails, but the exact minimum and maximum supply voltages are not stated in the available product records. According to the Analog Devices AD504 product page, engineers should use the manufacturer datasheet for the complete electrical-characteristics table. Confirm the supply limits against the circuit's signal range, output headroom, and temperature before using the amplifier in a new or modified design.
What are the key specifications of AD504SH that engineers should know?
The AD504SH is a single bipolar operational amplifier with 300 kHz nominal unity-gain bandwidth, 120 dB nominal common-mode rejection ratio, and 500 uV maximum input offset voltage. Its listed supply current is 1.5 mA, typical output current is 25 mA, and its operating range is -55 C to +125 C. These figures position it as a low-power precision amplifier for low-level instrumentation rather than a high-speed signal amplifier.
Where can I download the AD504SH datasheet PDF?
The official AD504 datasheet is available from the Analog Devices product page at https://www.analog.com/en/products/ad504.html. The manufacturer identifies the product as obsolete and links the obsolete data sheet for the AD504 family. Use that document to confirm the AD504SH pin assignments, supply-voltage limits, electrical characteristics, package drawing, and any grade-specific test requirements before beginning a board-level design.
Where can I find the AD504SH pinout?
Use the pin-description table and package drawing in the official Analog Devices AD504 datasheet for the authoritative AD504SH TO-99-8 pinout. The package is described as an eight-terminal, round, hermetically sealed TO-99 metal can with wire leads. Do not infer the terminal order from the drawing alone because the metal-can orientation and pin numbering must match the physical device and the original PCB footprint.
What is the bandwidth of the AD504SH operational amplifier?
The AD504SH has a nominal unity-gain bandwidth of 300 kHz. According to the AD504 product listing, this bandwidth places the amplifier in the low-frequency precision and instrumentation category rather than the high-speed operational-amplifier category. Actual closed-loop bandwidth depends on the selected feedback topology, gain, load, and stability conditions, so use the manufacturer curves when confirming behavior at a particular gain or capacitive-load condition.
Is AD504SH suitable for precision sensor measurement?
Yes, AD504SH is suitable for many precision sensor-measurement front ends when its 300 kHz bandwidth and 500 uV maximum offset are adequate. Its 120 dB nominal common-mode rejection ratio helps attenuate common-mode input noise, while the 1.5 mA supply current suits low-power instrumentation. Input bias current, input common-mode range, offset drift, and bias compensation must also be checked because they can dominate the total measurement error.
What is the difference between AD504SH and AD504SH/883?
The AD504SH and AD504SH/883 share the core AD504 amplifier ratings, including 500 uV maximum offset voltage, 300 kHz nominal unity-gain bandwidth, and 120 dB nominal common-mode rejection ratio. The principal distinction is the /883 designation, which identifies a military-qualified or screened ordering variant. Confirm the exact procurement requirements and qualification documentation because the standard orderable suffix and the screened suffix are not interchangeable without manufacturer approval.
What is the best drop-in replacement for AD504SH?
AD504SH/883 is the closest documented same-family drop-in candidate because it retains the AD504SH electrical ratings and TO-99-8 lead arrangement. It adds a screened military designation rather than improving speed or accuracy. A true replacement still requires matching the supply range, common-mode input range, offset, bias current, compensation, pinout, and qualification requirements. If those requirements are not identical, treat the part as a redesign candidate rather than a drop-in substitute.
Can AD504SH/883B replace AD504SH in an existing circuit?
AD504SH/883B can be considered for an existing TO-99-8 AD504SH position because its documented ratings retain the 500 uV maximum offset voltage, 300 kHz nominal unity-gain bandwidth, and 120 dB nominal common-mode rejection ratio, with a 125 C maximum operating temperature. Before substitution, verify the complete pin description, supply range, qualification record, and any screening or revision requirements. The /883B suffix is a documented family variant, not proof that every lifecycle or procurement requirement is identical.
What can replace AD504SH in a legacy amplifier circuit?
The documented replacement path for an AD504SH legacy circuit begins with AD504SH/883 or AD504SH/883B because both preserve the AD504 family's core electrical ratings and eight-lead TO-99 form. Start with the AD504SH/883 option when screened military supply is acceptable. Cross-brand substitutions cannot be recommended from the available cross-reference results without a verified pinout and parametric comparison. Request a quote on this page to check availability and lead time for the selected suffix.
When should I choose AD504SH over a modern surface-mount amplifier?
Choose AD504SH when maintaining an existing hermetically sealed TO-99-8 design, qualifying a legacy military platform, or preserving the established AD504 electrical behavior is more important than minimizing board area. A modern surface-mount amplifier may offer a smaller footprint, lower cost, or broader availability, but it can require pinout, compensation, common-mode-range, and qualification changes. Use AD504SH for drop-in maintenance where its documented 300 kHz bandwidth and 500 uV offset meet the circuit requirements.
Is AD504SH the same as AD504SH/883?
No. AD504SH and AD504SH/883 are related AD504-family ordering variants, not identical orderable designations. The available documentation gives both the same core performance figures—500 uV maximum offset, 300 kHz nominal unity-gain bandwidth, and 120 dB nominal CMRR—but AD504SH/883 carries the additional /883 screening or qualification designation. Verify the required grade and certification records before substitution.
What is the best Analog Devices equivalent for AD504SH?
AD504SH/883 is the strongest same-manufacturer equivalent identified for AD504SH because it retains the 500 uV maximum input offset voltage, 300 kHz nominal unity-gain bandwidth, and 120 dB nominal common-mode rejection ratio in the same AD504 product family. It is intended primarily for screened or qualified legacy requirements. The AD504SH/883B designation provides another documented family variant. Confirm the complete pin and electrical requirements before approving either substitution.
How much current does the AD504SH consume?
The AD504SH has a listed supply current of 1.5 mA. According to the product records, it is a low-power single amplifier with a typical output-current capability of 25 mA. Supply-current demand varies with supply voltage, input common-mode voltage, output swing, and load, so the 1.5 mA figure should be treated as the nominal device specification. The manufacturer's obsolete datasheet should be used for test conditions and worst-case design calculations.
Is AD504SH currently active and where can it be sourced?
The AD504SH is obsolete, as stated on the Analog Devices product page. Legacy inventory and heritage-order availability may still exist, but stock, minimum order quantity, and lead time can change. Use the Request a Quote form on this page to request current availability and sourcing for the exact AD504SH suffix. For repair histories, screen the AD504SH/883 and AD504SH/883B variants separately when military screening is required.

بيانات مرجعية هندسية لـ AD504SH — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose AD504SH when maintaining an existing TO-99-8 precision-amplifier circuit, reproducing a legacy military module, or maintaining controlled historical inventory. Its 300 kHz nominal unity-gain bandwidth, 500 uV maximum offset, 120 dB nominal CMRR, 1.5 mA supply current, and -55 C to +125 C range define its suitability for low-level instrumentation rather than high-speed signal processing. Choose AD504SH/883 when the screened or qualified /883 designation is required and the same core ratings and package are acceptable. Choose AD504SH/883B when its qualification revision meets the governing procurement specification. Modern surface-mount amplifiers should be evaluated for new designs, but they are not automatic drop-in replacements because pinout, common-mode range, stability, qualification, and PCB changes must be validated. No verified cross-brand TO-99-8 equivalent was identified, so a redesign-level comparison is required before selecting another manufacturer.

المقارنة مع البدائل

المعامل هذا المنتج AD504SH/883 AD504SH/883B
Package TO-99-8 (CBCY8), hermetically sealed TO-99-8 (CBCY8), hermetically sealed TO-99-8 (CBCY8), hermetically sealed
Brand Analog Devices Analog Devices Analog Devices
Maximum Input Offset Voltage 500 uV 500 uV 500 uV
Nominal Unity-Gain Bandwidth 300 kHz 300 kHz 300 kHz
Nominal Common-Mode Rejection Ratio 120 dB 120 dB 120 dB
Maximum Operating Temperature 125 C 125 C 125 C
Number of Circuits 1 1 1

أبرز الفروقات

  • Maintains the same documented core precision ratings as the screened family variants (مقابلAD504SH/883)
  • Supports controlled legacy procurement without changing the core amplifier performance (مقابلAD504SH/883B)
  • Combines a low-power bias with wide-range legacy temperature operation (مقابلAD504SH/883)

ملاحظات التصميم

AD504SH uses an eight-lead hermetically sealed TO-99 metal-can package rather than a surface-mount footprint. Preserve the original lead spacing, hole pattern, and metal-can orientation because pin 1 and the surrounding terminal sequence must match the manufacturer's package drawing. Check the lead diameter and solder-joint design against the applicable legacy PCB standard before replication. Do not substitute a similarly sized eight-pin plastic package without reviewing lead geometry, thermal behavior, and the complete pin-description table.

The listed 1.5 mA supply current makes AD504SH appropriate for low-power signal-conditioning systems, but supply selection must still account for load current, output swing, and the bipolar input structure. Confirm the minimum and maximum supply voltages from the manufacturer datasheet and ensure that the required input and output voltages remain inside their specified ranges. Place any required bypass capacitors close to the appropriate supply terminals and preserve the recommended grounding arrangement to avoid adding noise or instability.

Do not equate the AD504SH, AD504SH/883, and AD504SH/883B suffixes without reviewing qualification and screening requirements. The documented core ratings are identical, including 500 uV maximum offset, 300 kHz nominal bandwidth, and 120 dB nominal CMRR, but the /883 designations identify controlled or qualified ordering variants. For repair inventory, record the exact suffix and screening requirements, and validate the replacement in the finished circuit rather than relying only on package and headline performance comparisons.

The 300 kHz nominal unity-gain bandwidth is adequate for many low-level measurement loops but does not imply equal closed-loop bandwidth at every gain. Derive noise gain, check feedback stability for the intended gain, and evaluate capacitive loading using the manufacturer's stability guidance. For low-frequency precision use, include 500 uV maximum offset, input bias current, offset drift, and common-mode error in the system error budget. A resistor network can reduce offset contribution only when bias current and noise remain acceptable.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The Analog Devices product page identifies AD504 as obsolete. The available records identify a military temperature grade and /883 screening designation, but they do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.

تم التحقق من البيانات في: 2026-11-17 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

AD504SH datasheet AD504SH datasheet pdf AD504SH pinout AD504SH specifications AD504SH TO-99-8 Analog Devices AD504SH AD504SH replacement AD504SH equivalent AD504SH vs AD504SH/883 AD504SH precision op amp AD504SH price AD504SH stock AD504SH lead time AD504SH military op amp AD504SH 300 kHz bandwidth

المكونات والمصطلحات ذات الصلة

Analog Devices AD504SH AD504SH/883 AD504SH/883B AD504 operational amplifier precision amplifier general-purpose amplifier voltage-feedback amplifier bipolar input TO-99-8 CBCY8 hermetic metal can through-hole package signal conditioning precision measurement bridge sensor common-mode rejection ratio CMRR unity-gain bandwidth input offset voltage supply current military temperature grade surface-mount amplifier legacy component maintenance
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر