AD504SH - 300 kHz Precision Op Amp | Analog Devices
MPN: AD504SH ✗ پایان تولیدAD504SH نمای کلی
An operational amplifier is a voltage-feedback amplifier that uses differential input voltage to control an output voltage. The AD504SH belongs to the general-purpose operational-amplifier hierarchy, where precision offset, common-mode rejection, low supply current, and stable unity-gain behavior are important for sensors, instrumentation, and low-level analog signals. Its 1.5 mA supply-current specification places it in the low-power segment of the AD504 family.
The most prominent characteristics are the 300 kHz unity-gain bandwidth, 120 dB nominal common-mode rejection ratio, 500 uV maximum input offset voltage, and approximately 25 mA typical output-current capability. These ratings make the device suitable for signal paths requiring moderate bandwidth rather than high-speed waveform processing. The 120 dB CMRR helps reject common-mode interference, while the offset limit supports precision measurements when appropriately calibrated.
The AD504SH uses a conventional eight-terminal metal-can package and is listed with bipolar input characteristics. Its 300 kHz nominal unity-gain bandwidth is suitable for low-frequency precision loops and moderate-bandwidth signal amplification. Because the device is obsolete and specified in a hermetically sealed TO-99-8 package, it is principally relevant to maintenance, repair, and legacy-system replication rather than new high-volume surface-mount designs.
Typical uses include bridge-amplifier interfaces for resistive sensors, precision current measurement, low-level instrumentation, data acquisition front ends, and military-grade test equipment. In these applications, the AD504SH can amplify a small differential signal while rejecting common-mode voltage and limiting the bias current drawn from the supply. The -55 C to +125 C temperature range supports harsh environmental equipment when appropriate derating and screening are used.
Designers should follow the manufacturer's obsolete datasheet for the complete pin description, supply limits, electrical characteristics, and military qualification information. Stable operation requires adequate supply voltage, suitable output-voltage headroom, and decoupling close to the supply terminals. Existing TO-99 layouts must preserve the original lead numbering and metal-can orientation because the package is not surface mount.
This product page consolidates the obsolete-product status, key electrical ratings, package details, sourcing information, and documented AD504 family alternatives. It also distinguishes the standard AD504SH from screened AD504SH/883 and AD504SH/883B variants so engineers can select a replacement or heritage-order component without changing the TO-99-8 footprint.
جایگزینهای drop-in برای AD504SH — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
AD504SH/883
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD504SH/883B
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD504SH حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Circuits | 1 circuit |
| Maximum Input Offset Voltage | 500 uV |
| Nominal Unity-Gain Bandwidth | 300 kHz |
| Nominal Common-Mode Rejection Ratio | 120 dB |
| Maximum Operating Temperature | 125 C |
| Minimum Operating Temperature | -55 C |
| جریان تغذیه | 1.5 mA |
| Typical Output Current | 25 mA |
| Input Technology | Bipolar |
| بستهبندی | TO-99-8 (CBCY8), hermetically sealed |
| Package Shape | Round |
| Number of Terminals | 8 |
| Terminal Form | Wire |
| نوع نصب | Through-hole |
| Temperature Grade | Military |
| وضعیت چرخه عمر | Obsolete |
| AEC-Q100 Qualification | Not applicable |
راهنمای پیکربندی پین AD504SH round
پیکربندی پین برای AD504SH (پکیج round). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای AD504SH.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
AD504SH مناسب است برای 6 کاربردs: Precision Bridge Sensor Interface, Low-Level Instrumentation Amplification, Military Legacy Signal Conditioning, Precision Current Measurement, Industrial Process Signal Conditioning, Laboratory Reference Signal Conditioning.
Precision Bridge Sensor Interface
The AD504SH fits low-level bridge-sensor front ends where a 500 uV maximum offset limit, 120 dB nominal common-mode rejection ratio, and 300 kHz unity-gain bandwidth are sufficient. Its 1.5 mA supply current also helps limit the amplifier's contribution to a portable or distributed measurement system. Place the device in an instrumentation configuration with matched resistors and verify input bias current, offset drift, and common-mode limits for the selected sensor. Because AD504SH is obsolete, new designs should preserve the TO-99-8 footprint only when maintaining an existing platform or building a controlled heritage assembly.
پیشنهادی
Low-Level Instrumentation Amplification
AD504SH is suitable for instrumentation circuits that amplify small differential signals while rejecting common-mode interference. Its nominal 120 dB common-mode rejection ratio and 500 uV maximum input offset voltage provide the principal selection criteria, while the 300 kHz bandwidth supports moderate-frequency measurement channels rather than very fast data-acquisition systems. The 25 mA typical output-current rating gives adequate drive for many analog stages and external bias networks. Confirm supply polarity, output swing, and input common-mode range against the AD504 datasheet before committing the amplifier to a laboratory or industrial measurement chain.
پیشنهادی
Military Legacy Signal Conditioning
The hermetically sealed TO-99-8 AD504SH is relevant to legacy military signal-conditioning modules that were designed around a 300 kHz precision amplifier with 500 uV maximum offset. Its -55 C to +125 C operating range and military temperature grade support environmental requirements when the complete circuit, screening process, and qualification documentation are appropriate. The AD504SH/883 and AD504SH/883B designations offer documented family alternatives for screened or qualified maintenance. Engineers should compare lot-control, screening, test-temperature, and certificate requirements rather than relying on electrical similarity alone.
پیشنهادی
Precision Current Measurement
AD504SH can amplify the voltage generated by a current-sense element when the required signal bandwidth remains below the amplifier's 300 kHz nominal unity-gain bandwidth. Its maximum input offset voltage of 500 uV sets an important floor for current-sense resolution, while the 120 dB nominal common-mode rejection ratio helps when the sense element sits near a larger supply-derived voltage. The 1.5 mA supply current can reduce loading in compact monitoring systems. A practical design must also check input bias current, common-mode range, supply voltage, and output saturation before selecting this obsolete device.
پیشنهادی
Industrial Process Signal Conditioning
The AD504SH is applicable to legacy industrial process-control modules that condition low-level analog signals and require a wide -55 C to +125 C temperature range. Its 120 dB nominal common-mode rejection ratio is useful when the input includes substantial system noise, while the 300 kHz bandwidth covers many pressure, temperature, and position sensing loops without requiring a high-speed amplifier. The TO-99-8 through-hole package remains useful for rugged repairable assemblies, although it consumes more board area than modern surface-mount devices. Verify long-term offset drift and input bias-current behavior for each production or maintenance build.
پیشنهادی
Laboratory Reference Signal Conditioning
AD504SH can be used in laboratory signal-conditioning modules where a low 1.5 mA supply current and 120 dB nominal common-mode rejection ratio are useful in compact measurement instruments. Its 300 kHz nominal unity-gain bandwidth accommodates low- and moderate-bandwidth analog signals but not precision waveform capture at megahertz rates. The 500 uV maximum offset specification should be included in the total error budget, along with bias current, drift, and resistor tolerances. For new instruments, evaluate modern alternatives first; for repairing an existing TO-99-8 board, the AD504 family remains the relevant source of electrical and package information.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای AD504SH — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | AD504SH/883 | AD504SH/883B |
|---|---|---|---|
| Package | TO-99-8 (CBCY8), hermetically sealed | TO-99-8 (CBCY8), hermetically sealed | TO-99-8 (CBCY8), hermetically sealed |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Maximum Input Offset Voltage | 500 uV | 500 uV | 500 uV |
| Nominal Unity-Gain Bandwidth | 300 kHz | 300 kHz | 300 kHz |
| Nominal Common-Mode Rejection Ratio | 120 dB | 120 dB | 120 dB |
| Maximum Operating Temperature | 125 C | 125 C | 125 C |
| Number of Circuits | 1 | 1 | 1 |
تفاوتهای کلیدی
- Maintains the same documented core precision ratings as the screened family variants (در مقابلAD504SH/883)
- Supports controlled legacy procurement without changing the core amplifier performance (در مقابلAD504SH/883B)
- Combines a low-power bias with wide-range legacy temperature operation (در مقابلAD504SH/883)
یادداشتهای طراحی
AD504SH uses an eight-lead hermetically sealed TO-99 metal-can package rather than a surface-mount footprint. Preserve the original lead spacing, hole pattern, and metal-can orientation because pin 1 and the surrounding terminal sequence must match the manufacturer's package drawing. Check the lead diameter and solder-joint design against the applicable legacy PCB standard before replication. Do not substitute a similarly sized eight-pin plastic package without reviewing lead geometry, thermal behavior, and the complete pin-description table.
The listed 1.5 mA supply current makes AD504SH appropriate for low-power signal-conditioning systems, but supply selection must still account for load current, output swing, and the bipolar input structure. Confirm the minimum and maximum supply voltages from the manufacturer datasheet and ensure that the required input and output voltages remain inside their specified ranges. Place any required bypass capacitors close to the appropriate supply terminals and preserve the recommended grounding arrangement to avoid adding noise or instability.
Do not equate the AD504SH, AD504SH/883, and AD504SH/883B suffixes without reviewing qualification and screening requirements. The documented core ratings are identical, including 500 uV maximum offset, 300 kHz nominal bandwidth, and 120 dB nominal CMRR, but the /883 designations identify controlled or qualified ordering variants. For repair inventory, record the exact suffix and screening requirements, and validate the replacement in the finished circuit rather than relying only on package and headline performance comparisons.
The 300 kHz nominal unity-gain bandwidth is adequate for many low-level measurement loops but does not imply equal closed-loop bandwidth at every gain. Derive noise gain, check feedback stability for the intended gain, and evaluate capacitive loading using the manufacturer's stability guidance. For low-frequency precision use, include 500 uV maximum offset, input bias current, offset drift, and common-mode error in the system error budget. A resistor network can reduce offset contribution only when bias current and noise remain acceptable.
اطلاعات انطباق
The Analog Devices product page identifies AD504 as obsolete. The available records identify a military temperature grade and /883 screening designation, but they do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.