AD625AD - Programmable Gain Instrumentation Amplifier | Analog Devices
MPN: AD625AD ✗ انتهى عمره الإنتاجيAD625AD نظرة عامة
An instrumentation amplifier is a specialized amplifier category designed to amplify small differential signals while rejecting common-mode interference. Its internal topology and external gain resistor make it particularly useful when input impedance, gain accuracy, and common-mode rejection must be maintained simultaneously. In the signal-chain hierarchy, the AD625AD belongs to the precision instrumentation-amplifier family within amplifier ICs and analog signal-conditioning components.
Key characteristics include a maximum low-gain error of 0.02%, maximum low-gain temperature coefficient of 5 ppm/°C, maximum low nonlinearity of 0.001%, and a maximum offset voltage of 200 µV. The 25 MHz gain-bandwidth product allows the closed-loop bandwidth to decrease as gain increases, making the amplifier suitable for both precision measurement and higher-frequency sensor interfaces.
The AD625AD uses an external gain-setting resistor to establish its programmed gain. Designers must calculate the required resistance from the device's gain equation and verify resistor tolerance, temperature coefficient, parasitics, and stability across the intended signal bandwidth. Its 4 nV/√Hz noise characteristic is particularly relevant when resolving low-amplitude transducer outputs without allowing amplifier noise to dominate the measurement.
Typical applications include bridge and strain-gage signal conditioning, biomedical instrumentation, laboratory measurement systems, precision current measurement, and industrial sensor interfaces. The 16-CDIP package is useful where a through-hole assembly and long service life are preferred over a surface-mount footprint, although the larger board area and through-hole thermal behavior must be considered in compact systems.
The primary design trade-off is bandwidth versus gain. The 25 MHz gain-bandwidth product supports a range of measurement speeds, but useful closed-loop bandwidth falls as the selected gain rises. Layout should therefore use short signal paths, a clean analog ground reference, and an external gain resistor positioned close to the gain-setting pin.
This page combines manufacturer specifications, lifecycle guidance, practical circuit-design considerations, sourcing information, and verified drop-in alternatives to support faster component evaluation and board-level planning.
بدائل مباشرة لـ AD625AD — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع AD625AD (نفس عامل الشكل والبصمة) — يختلف في Package, Product Type, Input Bias Current, RoHS Status, Slew Rate.
AD625CDZ
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←AD625AD الحدود القصوى والخصائص الكهربائية
| Product Type | Programmable-gain instrumentation amplifier |
| Number of Circuits | 1 circuit |
| User-Programmed Gain Range | 1 to 10,000 |
| Maximum Low-Gain Error | 0.02% max |
| Maximum Low-Gain Temperature Coefficient | 5 ppm/°C max |
| Maximum Low Nonlinearity | 0.001% max |
| Maximum Offset Voltage | 200 µV |
| Input Noise Density | 4 nV/√Hz at 1 kHz |
| Gain-Bandwidth Product | 25 MHz |
| Bandwidth | 0.65 MHz |
| Architecture | Bipolar |
| العلبة | 16-CDIP |
| عدد الأطراف | 16 pins |
| نوع التركيب | Through-hole |
| Design Recommendation | Not recommended for new designs |
| Data Sheet Revision | Rev. D |
دليل تكوين أطراف AD625AD 16-cdip
تكوين الأطراف لـ AD625AD (حزمة 16-cdip). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ AD625AD.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
AD625AD مناسب لـ 6 التطبيقs: Strain-Gage and Bridge Measurement, Biomedical Signal Conditioning, Precision Current Measurement, Laboratory Instrumentation, Industrial Sensor Interfaces, Low-Level Differential Signal Acquisition.
Strain-Gage and Bridge Measurement
The AD625AD fits strain-gage and resistive-bridge front ends that require substantial gain from small differential sensor outputs. Its programmable range extends to 10,000, while the maximum low-gain error of 0.02%, low-gain temperature coefficient of 5 ppm/°C max, and 4 nV/√Hz noise at 1 kHz support accurate signal recovery. Place the external gain-setting resistor close to the device, route the bridge and return paths differentially, and use a quiet analog ground. Because the 25 MHz gain-bandwidth product reduces usable bandwidth as gain rises, verify the required measurement bandwidth against the selected gain before finalizing the circuit.
موصى به
Biomedical Signal Conditioning
The AD625AD is appropriate for low-level biomedical instrumentation in which patient-derived or diagnostic signals must be amplified with controlled gain and low added noise. A gain of 1 to 10,000 allows the same amplifier family to cover multiple measurement ranges, and the 4 nV/√Hz input noise at 1 kHz helps avoid masking weak biosignals. Input protection, patient isolation, leakage current, and electrode-interface requirements must be handled separately from the amplifier itself. Keep high-gain interconnects short, shield sensitive routes where needed, and validate the complete analog chain for offset drift, nonlinearity, and common-mode behavior.
موصى به
Precision Current Measurement
The AD625AD can amplify the differential voltage generated by shunt-based current measurements when high common-mode voltage must be rejected. Its precision characteristics include a maximum low-gain error of 0.02% and maximum low nonlinearity of 0.001%, which help preserve measurement-chain accuracy. The 16-CDIP package also provides a practical through-hole implementation for laboratory and industrial instrumentation. Select the external gain resistor carefully, account for its tolerance and temperature coefficient, and avoid routing high-current return paths beneath the analog input network. Confirm that the selected gain provides the required bandwidth within the 25 MHz gain-bandwidth-product constraint.
موصى به
Laboratory Instrumentation
The AD625AD is well suited to laboratory measurement equipment requiring programmable gain, low offset, and flexible signal-range selection. Its gain can be set from 1 to 10,000 through an external resistor, while the 200 µV maximum offset voltage and 0.001% maximum low nonlinearity support precise front-end behavior. The device’s 25 MHz gain-bandwidth product supports a range of signal speeds, although bandwidth falls as gain increases. A practical instrument design should include calibration access, input attenuation or range switching, protection against external test faults, and a quiet reference plane to prevent switching currents from modulating the measured signal.
موصى به
Industrial Sensor Interfaces
The AD625AD can condition low-level outputs from pressure, temperature, position, and resistance-based sensors when the interface requires a wide programmable gain range. The 4 nV/√Hz noise density at 1 kHz is valuable for low-amplitude sensors, while the 0.02% maximum low-gain error supports calibrated systems. Use the 16-CDIP footprint only where through-hole assembly, serviceability, and thermal rise are acceptable. Industrial environments also require attention to EMI, surge events, ground loops, and sensor-excitation noise; filtering and protection should be placed where they do not compromise the required signal bandwidth.
موصى به
Low-Level Differential Signal Acquisition
The AD625AD supports acquisition of weak differential signals that share a large common-mode voltage. Its instrumentation-amplifier configuration is intended to provide accurate gain over a broad 1-to-10,000 range, and the bipolar implementation supports the precision requirements of this measurement class. The 25 MHz gain-bandwidth product must be evaluated at each operating gain because higher gains reduce closed-loop bandwidth. Maintain symmetric input routing, minimize connector and trace leakage where relevant, and place the gain-setting component near the relevant device pin. For new production programs, account for the manufacturer’s not-recommended-for-new-designs lifecycle position before committing the architecture.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ AD625AD — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | AD625CDZ |
|---|---|---|
| Package | 16-CDIP | 16-CDIP |
| Brand | Analog Devices | Analog Devices |
| Product Type | Programmable-gain instrumentation amplifier | Programmable-gain instrumentation amplifier |
| Circuit Count | 1 circuit | 1 circuit |
| User-Programmed Gain Range | 1 to 10,000 | 1 to 10,000 |
| Gain-Bandwidth Product | 25 MHz | 25 MHz |
| Input Noise Density | 4 nV/√Hz at 1 kHz | 4 nV/√Hz at 1 kHz |
| Maximum Low-Gain Error | 0.02% max | 0.02% max |
| Maximum Low-Gain Temperature Coefficient | 5 ppm/°C max | 5 ppm/°C max |
| Maximum Low Nonlinearity | 0.001% max | 0.001% max |
| Maximum Offset Voltage | 200 µV | 200 µV |
| New-Design Recommendation | Not recommended for new designs | Not recommended for new designs |
أبرز الفروقات
- Wide programmable gain in a precision instrumentation amplifier (مقابلAD625CDZ)
- Precision low-gain accuracy (مقابلAD625CDZ)
- Legacy-compatible ceramic-DIP implementation (مقابلAD625CDZ)
ملاحظات التصميم
Treat the external gain-setting resistor as part of the precision measurement system rather than as a generic resistor. Its tolerance and temperature coefficient contribute directly to gain accuracy, while resistance and parasitic capacitance affect the achievable closed-loop response. Use the gain relationship and resistor guidance in the Analog Devices AD625 Data Sheet Rev. D, place the resistor close to the gain-setting connection, and verify the final tolerance budget at the highest operating temperature.
Keep the differential input paths short, matched, and symmetric, and connect them to a quiet analog ground plane. High-gain measurements can pick up leakage, relay noise, switching supply ripple, and ground potential differences that are insignificant at low gain. Use a single-point analog reference where appropriate, separate noisy return currents from the sensor reference, and keep the gain-setting component away from high-current switching nodes.
Calculate usable bandwidth from the 25 MHz gain-bandwidth product at the selected programmed gain rather than assuming the full gain-bandwidth value is available at every gain. Higher gain reduces closed-loop bandwidth and may expose phase-margin or stability limitations. Confirm the intended signal spectrum, add only the filtering required by the application, and validate the complete amplifier and gain-resistor network with a bandwidth and stability test.
The 16-CDIP package can dissipate heat through its leads and board copper, but the through-hole assembly still requires adequate airflow and copper area at elevated ambient temperatures. Calculate dissipation from the actual supply voltage, output voltage, and load current, then compare the resulting junction-temperature rise with the device limits in the manufacturer datasheet. Avoid mounting the package directly above a heat source or in a sealed enclosure without thermal analysis.
معلومات الامتثال
The accessible manufacturer information identifies the AD625 family as not recommended for new designs but does not establish the exact compliance status of the AD625AD orderable variant. AEC-Q100 is not applicable because this is a general-purpose instrumentation amplifier rather than an automotive-qualified device.