ADC10662CIWMX - 10-Bit 1.5MSPS ADC w/ 2-Input MUX | Texas Instruments
MPN: ADC10662CIWMX ✗ انتهى عمره الإنتاجيADC10662CIWMX نظرة عامة
An ADC (analog-to-digital converter) is a semiconductor device that converts continuous analog signals into discrete digital codes. The ADC10662 belongs to the successive-approximation / multi-step flash hybrid converter family, which sits in the broader hierarchy of data converter -> signal chain IC -> analog mixed-signal IC. Its 2-input analog multiplexer allows two channels to be sampled without an external analog switch, simplifying front-end signal conditioning in data acquisition systems.
Key features include 10-bit resolution, 1.5 MSPS sampling rate (1.5M samples per second), 2 analog input channels, on-chip sample/hold, low power CMOS architecture, and a parallel digital output bus. The wide SOIC-24 package (7.5 mm body width) eases hand-prototyping and provides robust thermal performance for industrial environments.
The ADC10662 uses a patented multi-step conversion architecture that combines flash and successive-approximation techniques to achieve fast conversion (360 ns) at lower power than a full-flash 10-bit design. The on-chip sample-and-hold eliminates the need for an external track-and-hold amplifier, and the integrated 2-channel analog multiplexer reduces BOM cost in multi-sensor systems.
Typical applications include industrial process control, data acquisition systems, portable instrumentation, automotive sensor interfaces, and embedded control boards where 10-bit resolution at sub-microsecond conversion rates is sufficient. The wide SOIC package and 5 V supply simplify retrofit designs in legacy 8-bit and 16-bit microcontroller systems.
When designing with this device, note that the ADC10661 and ADC10662 families have been marked obsolete by the manufacturer; for new designs, consider pin-compatible alternatives in the same package. Decouple AVDD and DVDD separately with 0.1 uF ceramic capacitors placed close to the IC pins to keep digital switching noise out of the analog path.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet - including a cross-package compatibility matrix and verified industry-grade substitutes for EOL replacement planning.
بدائل مباشرة لـ ADC10662CIWMX — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع ADC10662CIWMX (نفس عامل الشكل والبصمة) — يختلف في Architecture, Package, Analog Supply Voltage, Conversion Time, Data Interface.
ADC10662CIWM/NOPB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ADC10062CIWM/NOPB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ADC10158CIWMX/NOPB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ADC10464CIWMX/NOPB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ADC10662CIWMX الحدود القصوى والخصائص الكهربائية
| الدقة | 10 bit |
| Number of Analog Inputs | 2 (multiplexed) |
| معدل أخذ العينات | 1.5 MSPS (1.5M samples per second) |
| Conversion Time | 360 ns |
| Architecture | Multi-step (Flash + Successive Approximation hybrid) |
| Data Interface | Parallel, word access |
| Analog Supply Voltage | +5 V (single supply) |
| On-Chip Sample/Hold | Yes |
| Number of Channels | 2 |
| Input Type | Single-ended, analog multiplexer |
| العلبة | 24-SOIC (SOIC-24, 7.50 mm body width, 300 mil) |
| Package Code | PDSO24 / SOP24 / SOIC-24 |
| Terminal Form | Gull Wing |
| درجة حرارة التشغيل | -40C to +85C (industrial grade) |
| نوع التركيب | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Technology | CMOS |
تكوين أطراف ADC10662CIWMX
| دبوس 1 | IN0 — Analog input channel 0 |
| دبوس 2 | IN1 — Analog input channel 1 |
| دبوس 3 | AGND — Analog ground |
| دبوس 4 | AVDD — Analog +5 V supply |
| دبوس 5 | VREF — Reference voltage input |
| دبوس 6 | REFOUT — Internal reference output |
| دبوس 7 | DGND — Digital ground |
| دبوس 8 | DVDD — Digital +5 V supply |
| دبوس 9 | DB0 — Digital output bit 0 (LSB) |
| دبوس 10 | DB1 — Digital output bit 1 |
| دبوس 11 | DB2 — Digital output bit 2 |
| دبوس 12 | DB3 — Digital output bit 3 |
| دبوس 13 | DB4 — Digital output bit 4 |
| دبوس 14 | DB5 — Digital output bit 5 |
| دبوس 15 | DB6 — Digital output bit 6 |
| دبوس 16 | DB7 — Digital output bit 7 |
| دبوس 17 | DB8 — Digital output bit 8 |
| دبوس 18 | DB9 — Digital output bit 9 (MSB) |
| دبوس 19 | MUXSEL — Analog input channel select |
| دبوس 20 | CONVST — Conversion start |
| دبوس 21 | RD — Read strobe |
| دبوس 22 | CS — Chip select (active low) |
| دبوس 23 | INT — Conversion complete interrupt |
| دبوس 24 | OF — Overflow output |
التطبيقات النموذجية
ADC10662CIWMX مناسب لـ 6 التطبيقs: Industrial Process Control, Data Acquisition Systems (DAQ), Portable Instrumentation, Automotive Sensor Interface, Embedded Control Boards, Legacy Repair and Maintenance.
Industrial Process Control
The ADC10662CIWMX fits industrial process control loops where 10-bit resolution and 1.5 MSPS sampling rate are sufficient to digitize sensor outputs from thermocouples, pressure transducers, and 4-20 mA loop receivers. Its 2-channel on-chip multiplexer handles two sensor inputs without an external analog switch, reducing BOM cost. The 5 V single supply aligns with industrial 24V->5V rails, and the -40C to +85C industrial temperature range supports factory-floor deployment. Engineers should add RC anti-aliasing filters ahead of each analog input and use separate AVDD/DVDD decoupling to keep PLC digital switching noise out of the conversion path.
موصى به
Data Acquisition Systems (DAQ)
In multi-channel data acquisition systems, the ADC10662CIWMX serves as a per-board ADC for low-channel-count subsystems. Its parallel word-access interface allows direct connection to 8-bit and 16-bit microcontrollers or FPGAs without serial-port overhead, supporting 1.5 MSPS real-time sampling. The on-chip sample-and-hold eliminates external THA, simplifying board layout. For higher channel count, multiple ADC10662 devices can be paralleled. The wide SOIC-24 package supports hand-prototyping and rework in laboratory DAQ instruments.
موصى به
Portable Instrumentation
The ADC10662CIWMX is well-suited to portable handheld instruments such as digital multimeters, portable oscilloscope front-ends, and field data loggers. Its CMOS multi-step architecture delivers 1.5 MSPS at modest power consumption, extending battery life. The 2-input MUX supports differential measurement setups (sensor + reference) without extra switching ICs. Industrial temperature range allows field deployment across seasons. Design tip: route the analog ground (AGND) separately from digital ground (DGND) and tie them at a single point near the IC to minimize ground-loop noise in low-level measurements.
موصى به
Automotive Sensor Interface
In non-safety automotive applications, the ADC10662CIWMX can digitize outputs from throttle position sensors, manifold pressure sensors, and temperature probes in older vehicle ECUs. Its industrial temperature range covers under-hood conditions for many platforms, and the 5 V supply is standard in 12V automotive electrical systems. For new automotive designs, however, the lack of AEC-Q100 qualification is a hard constraint; engineers should migrate to AEC-Q100-qualified alternatives such as the TI ADC10158 family. The wide SOIC package aids rework in service-depot repair scenarios.
موصى به
Embedded Control Boards
The ADC10662CIWMX is commonly used on legacy 8-bit and 16-bit microcontroller expansion boards for digitizing analog sensors - think HVAC controllers, security panel I/O, and industrial scale indicators. Its parallel interface matches legacy bus architectures without requiring an SPI or I2C engine, simplifying firmware. The 2-channel MUX supports redundant sensor inputs for fault detection. Designers should note the part's obsolete status and plan a transition to current-production TI ADCs in the same SOIC-24 footprint for new board revisions.
موصى به
Legacy Repair and Maintenance
Because the ADC10662CIWMX is obsolete but still in service in thousands of legacy systems, a primary use today is repair and maintenance of installed equipment - factory PLCs, lab instruments, military/aerospace test gear, and older medical devices. Rochester Electronics and aftermarket distributors stock the part for this support market. Engineers performing board repair should verify the exact suffix (CIWMX vs CIWM) when ordering, since both share the same die but different packaging. The wide SOIC-24 footprint simplifies hand-soldering during depot-level rework.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ADC10662CIWMX — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | ADC10662CIWM/NOPB | ADC10062CIWM/NOPB | ADC10158CIWMX/NOPB | ADC10464CIWMX/NOPB |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 24-SOIC (7.50 mm wide) | 24-SOIC (7.50 mm wide) - same | 24-SOIC (7.50 mm wide) - same | 24-SOIC (7.50 mm wide) - same | 24-SOIC (7.50 mm wide) - same |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit |
| Sampling Rate | 1.5 MSPS | 1.5 MSPS | ~1.5 MSPS | ~0.5 MSPS | ~3 MSPS |
| Number of Input Channels | 2 | 2 | 2 | 8 | 2 |
| Data Interface | Parallel | Parallel | Parallel | Parallel | Parallel |
| Supply Voltage | +5 V single | +5 V single | +5 V single | +5 V single | +5 V single |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Lifecycle Status | Obsolete | Obsolete | Active | Active | Active |
أبرز الفروقات
- On-chip 2-input analog multiplexer (مقابلADC10464CIWMX/NOPB)
- Wide SOIC-24 (7.5 mm) package for easy prototyping (مقابلADC10062CIWM/NOPB)
- Patented multi-step flash + SAR hybrid architecture (مقابلPure SAR ADCs in same package)
ملاحظات التصميم
Decouple AVDD (analog +5 V, pin 4) and DVDD (digital +5 V, pin 8) separately, each with a 0.1 uF ceramic capacitor placed within 5 mm of the IC pin. Add a 10 uF bulk tantalum or ceramic cap on each supply rail to suppress transient current spikes during conversion. Tie AGND (pin 3) and DGND (pin 7) at a single point near the IC to avoid ground-loop noise coupling into the analog path. A common pitfall is sharing a single ground pour; this couples digital switching noise into the analog input and degrades effective resolution.
Route analog input traces (IN0, IN1) away from digital output bus lines (DB0-DB9, CONVST, RD, CS) to minimize digital-to-analog crosstalk. Use a ground guard trace on each side of the analog input lines if the layout is dense. Keep the VREF bypass cap within 3 mm of pin 5. Estimated: at 1.5 MSPS with 10-bit resolution, the analog input bandwidth is ~750 kHz (Nyquist); layout-induced stray capacitance above 5 pF can introduce -3 dB roll-off and degrade SNR.
Do not leave MUXSEL (pin 19) floating - tie it high or low through a 10 kohm resistor to a defined logic level, or channel selection will be indeterminate at power-up. Ensure CONVST (pin 20) meets the minimum pulse-width spec from the datasheet; pulses shorter than the spec cause incomplete conversion and erroneous output codes. When using the internal reference (REFOUT, pin 6), add a 1-10 uF bypass cap; without it, reference noise couples into the conversion and INL degrades by 0.5-1 LSB.
معلومات الامتثال
Compliance data not present in verified web sources. Part originated at National Semiconductor, now under Texas Instruments. Part is obsolete per TI lifecycle policy. AEC-Q100 not qualified - migrate to AEC-Q100 alternatives for new automotive designs.
