TPS63070RNMT - 2V-16V, 2A Buck-Boost Converter | TI
MPN: TPS63070RNMT ✓ نشطTPS63070RNMT نظرة عامة
A buck-boost converter is a type of DC-DC switching regulator within the broader power management IC category that combines buck (step-down) and boost (step-up) topologies. This lets a single inductor-based stage produce a stable rail from sources such as 4-cell alkaline, 12V lead-acid, or solar inputs whose voltage swings across the output level. The TPS63070 belongs to the switching voltage regulator family used in portable, industrial, and IoT power systems.
Key features include a 3.6A switch current limit, 2.4MHz switching frequency, and low quiescent current of approximately 50uA typical. Synchronous rectification with integrated MOSFETs improves efficiency and reduces external component count, while the 2.4MHz clock permits small inductors and capacitors for a compact footprint. PWM mode maximizes heavy-load efficiency and PFM mode preserves light-load efficiency; the device also supports negative output current sinking in PWM mode per TI datasheet SLVSDD7B.
Architecture-wise, the four-switch synchronous buck-boost topology seamlessly transitions between buck, buck-boost, and boost operating regions with a single inductor, avoiding output discontinuity when the battery voltage crosses the setpoint. The adjustable feedback (FB) pin sets the output with a resistor divider, and programmable soft-start limits inrush current.
Typical applications include battery-powered portable instruments, industrial sensors, IoT wireless nodes, and 12V rail conditioning for microcontrollers, RF modules, and displays. Wide input tolerance makes it ideal for solar or vehicle-supplied systems.
For best results, keep the inductor and input/output capacitor loops short, place the input capacitor at VIN and PGND, and provide adequate copper on the thermal pad. Pricing references are as of 2026-08-28.
بدائل مباشرة لـ TPS63070RNMT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع TPS63070RNMT (نفس عامل الشكل والبصمة) — يختلف في Input Voltage Range, Operating Temperature, Output Type, Output Voltage Range, Package.
TPS63070QRNMTQ1
تواصل لمعرفة السعر
عرض ورقة البيانات ←TPS63070RNMR
📋 بديل مرجعي (غير موجود في الكتالوج)
TPS630701RNMR
📋 بديل مرجعي (غير موجود في الكتالوج)
TPS630702RNMR
📋 بديل مرجعي (غير موجود في الكتالوج)
TPS63070QNMRQ1
📋 بديل مرجعي (غير موجود في الكتالوج)
TPS63070RNMT الحدود القصوى والخصائص الكهربائية
| البنية الطوبولوجية | Buck-Boost (synchronous) |
| نطاق جهد الدخل | 2 V to 16 V |
| نطاق جهد الخرج | 2.5 V to 9 V (adjustable) |
| Output Current | 2 A |
| Switch Current Limit | 3.6 A |
| تردد التبديل | 2.4 MHz |
| عدد المخارج | 1 |
| نوع الخرج | Adjustable (FB pin) |
| درجة حرارة التشغيل | -40C to +125C (TJ) |
| العلبة | VQFN-HR (RNM), 15 pins |
| نوع التركيب | Surface Mount |
| التقويم المتزامن | Yes (integrated MOSFETs) |
| Control Modes | PWM / PFM |
| بدء التشغيل الناعم | Programmable |
| الإيقاف الحراري | Yes |
| Negative Current Sinking | Supported in PWM mode |
تكوين أطراف TPS63070RNMT
| دبوس 1 | PGND — Power ground |
| دبوس 2 | VIN — Power input, 2V-16V |
| دبوس 3 | VINA — Analog supply for control circuit |
| دبوس 4 | EN — Enable input |
| دبوس 5 | SS/TR — Soft-start / tracking pin |
| دبوس 6 | FB — Feedback, sets output with resistor divider |
| دبوس 7 | PGND — Power ground |
| دبوس 8 | SW1 — Switch node 1, connect inductor |
| دبوس 9 | SW1 — Switch node 1 |
| دبوس 10 | SW2 — Switch node 2, connect inductor |
| دبوس 11 | SW2 — Switch node 2 |
| دبوس 12 | VOUT — Regulated output, 2.5V-9V |
| دبوس 13 | VOUT — Regulated output |
| دبوس 14 | GND — Ground |
| دبوس 15 | PGND — Power ground / thermal pad |
التطبيقات النموذجية
TPS63070RNMT مناسب لـ 6 التطبيقs: 12V Rail Conditioning for MCUs and RF Modules, Battery-Powered Portable Instruments, IoT Wireless Sensor Nodes, Solar-Powered Systems, Automotive 12V Subsystems, Display and LED Bias Supplies.
12V Rail Conditioning for MCUs and RF Modules
Industrial control boards often run from 12V or 24V rails that sag or spike across the 5V logic level. The TPS63070RNMT accepts 2V-16V input and regulates a stable 5V at up to 2A, passing seamlessly through buck, buck-boost, and boost regions without output dropout. Its 2.4MHz switching keeps inductors small, and synchronous rectification sustains high efficiency for always-on microcontroller and radio loads.
موصى به
Battery-Powered Portable Instruments
Multi-cell alkaline or lithium battery packs swing from above to below the regulated rail as they discharge. The TPS63070RNMT's 2V-16V input and 2.5V-9V adjustable output maintain regulation across the entire discharge curve, while roughly 50uA quiescent current and PFM light-load mode extend battery life between charges or replacements in handheld test and measurement devices.
موصى به
IoT Wireless Sensor Nodes
Wireless sensor nodes need burst-current capability for radio transmit while idling at microamp levels. The TPS63070RNMT supplies 2A peaks for PA bursts from a 2V-16V solar or battery source, and its PFM mode preserves efficiency at sleep-state loads. The 2.4MHz operation permits a compact inductor, fitting constrained node PCBs. Output set by a single FB resistor divider simplifies rail provisioning.
موصى به
Solar-Powered Systems
Solar panel output voltage varies widely with irradiance and temperature, frequently crossing the battery or load voltage. The TPS63070RNMT's 2V-16V input range and automatic buck-boost transition deliver a constant output from dawn-to-dusk conditions without mode discontinuity, making it a simple single-inductor power stage for solar garden devices, remote telemetry, and energy-harvesting front ends.
موصى به
Automotive 12V Subsystems
With the AEC-Q100 qualified TPS63070QRNMTQ1 sibling, this family serves automotive modules supplied from 12V battery rails that droop during cranking below 6V and surge during load dump. The wide 2V-16V input holds infotainment or sensor-module outputs steady through both conditions, and the 2.4MHz switching keeps switching noise out of the AM radio band, easing EMC compliance.
موصى به
Display and LED Bias Supplies
Small TFT and OLED displays need stable 3.3V-9V rails from battery or USB inputs of varying voltage. The TPS63070RNMT regulates any setpoint in its 2.5V-9V range with 2A capability for display backlight drivers and panel logic. Integrated synchronous FETs and a 2.4MHz clock shrink the solution to a single small inductor, fitting slim display modules with tight height limits.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ TPS63070RNMT — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | TPS63070QRNMTQ1 | TPS63070RNMR | TPS630701RNMR | TPS630702RNMR |
|---|---|---|---|---|---|
| Package | VQFN-HR (RNM) 15-pin | VQFN-HR (RNM) 15-pin - same | VQFN-HR (RNM) 15-pin - same | VQFN-HR (RNM) 15-pin - same | VQFN-HR (RNM) 15-pin - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Input Voltage Range | 2V to 16V | 2V to 16V | 2V to 16V | 2V to 16V | 2V to 16V |
| Output Voltage | 2.5V-9V adjustable | 2.5V-9V adjustable | 2.5V-9V adjustable | 3.3V fixed | 5V fixed |
| Output Current | 2 A | 2 A | 2 A | 2 A | 2 A |
| Switch Current Limit | 3.6 A | 3.6 A | 3.6 A | 3.6 A | 3.6 A |
| Switching Frequency | 2.4 MHz | 2.4 MHz | 2.4 MHz | 2.4 MHz | 2.4 MHz |
| AEC-Q100 Qualification | No (standard grade) | Yes | No | No | No |
| Packing | Cut tape / small reel (T) | Cut tape (T) | Tape & reel 3000 (R) | Tape & reel 3000 (R) | Tape & reel 3000 (R) |
أبرز الفروقات
- Widest input range in TI buck-boost family (مقابلTPS63021)
- Automotive-qualified drop-in sibling (مقابلTPS63070QRNMTQ1)
- Higher output current than small buck-boosts (مقابلTPS62740DSSR)
ملاحظات التصميم
Place the input capacitor as close as possible to the VIN and PGND pins, and keep the SW1/SW2-to-inductor loop short and wide. The four-switch buck-boost topology circulates current through both switch nodes, so minimize the copper loop area of SW1-inductor-SW2 to limit radiated EMI at the 2.4MHz switching frequency. Follow TI datasheet SLVSDD7B Section 9 PCB layout guidelines.
The exposed thermal pad must be soldered to a solid ground plane with an array of thermal vias. At VIN=12V, VOUT=5V, 2A load, dissipation is roughly 1-2W depending on efficiency; inadequate copper can push the junction beyond the 125C rating. Use at least 1 square inch of 2oz copper or a buried ground plane under the pad for high-power continuous loads.
Do not omit the SS/TR soft-start capacitor; omitting it causes hard inrush at startup. Ensure the FB divider uses 1% resistors and the FB node is kept short to avoid noise pick-up. Verify the inductor saturation rating exceeds the 3.6A switch current limit - undersized inductors saturate and trigger current-limit instability.
معلومات الامتثال
RoHS compliance per distributor listings (DigiKey/LCSC). AEC-Q100 applies only to the TPS63070Q (Q1) variant, not this standard part. Verify REACH status on TI product page.
