ADM207EARS - 5/3 RS-232 Transceiver | Analog Devices
MPN: ADM207EARS ✓ نشطADM207EARS نظرة عامة
An RS-232 transceiver combines line drivers and line receivers on one integrated circuit. Digital logic-side signals enter the receivers and leave the drivers, while the external RS-232 ports use bipolar voltage signaling. The ADM207EARS therefore serves as the interface between low-voltage CMOS equipment and a physical RS-232 connection. It belongs to the RS-232 transceiver hierarchy alongside line drivers, line receivers, and multi-driver interface ICs.
Five driver channels allow one controller to connect to five external RS-232 ports, while three receiver channels can monitor three incoming data lines. Operation from a single 5 V supply simplifies system power design, and the specified 0.1 µF charge-pump capacitor requirement reduces external power-supply complexity. The device supports data rates to 230 kbps and is designed for robust communications interfaces.
The ADM207E family is intended for EIA-232E and CCITT V.28 signaling applications. According to the Analog Devices product page, it is suitable for harsh electrical environments and includes ESD protection rated at ±15 kV. These protections are important when equipment cables connect to user-accessible ports, where electrostatic discharge and transient events can otherwise damage the interface IC.
Typical uses include industrial serial-control equipment, data acquisition systems, instrumentation, POS terminals, and communications adapters. The five transmitters are useful in multiport controller designs, while the three receivers support status, handshake, or acknowledgment inputs. The 230 kbps maximum data rate supports legacy synchronous and asynchronous RS-232 links used in industrial control, test equipment, and embedded systems.
Layout should preserve short charge-pump paths and return the charge-pump capacitor close to the device. RS-232 driver outputs should also be isolated from sensitive analog inputs, and external protection may be needed for long cables or severe industrial transients. Confirm connector-level signaling and grounding before treating a logic-level UART connection as a complete RS-232 interface.
This page combines the manufacturer interface specifications, exact package and channel information, sourcing guidance, and a practical comparison with confirmed 24-SSOP alternatives. It also highlights the design checks that matter when replacing a multi-channel RS-232 transceiver without changing the PCB footprint.
بدائل مباشرة لـ ADM207EARS — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
ADM207EARSZ
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX207CDB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ADM207EARS المواصفات
| Product Type | RS-232 transceiver |
| Driver Channels | 5 channels |
| Receiver Channels | 3 channels |
| جهد التغذية | 5 V |
| Maximum Data Rate | 230 kbps |
| Logic Compatibility | +5 V CMOS |
| Charge-Pump Capacitor | 0.1 µF |
| العلبة | 24-pin SSOP |
| نوع التركيب | Surface mount |
| RS-232 Compliance | EIA-232E |
| V.28 Compliance | CCITT V.28 |
| ESD Protection | ±15 kV |
| Driver Output Type | RS-232 line driver |
| Receiver Input Type | RS-232 line receiver |
| Production Status | Production |
دليل تكوين أطراف ADM207EARS 24-pin ssop
تكوين الأطراف لـ ADM207EARS (حزمة 24-pin ssop). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ADM207EARS.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
ADM207EARS مناسب لـ 6 التطبيقs: Industrial Serial Control Equipment, Data Acquisition Systems, Test and Measurement Instruments, Point-of-Sale Terminals, Communication Port Expanders, Legacy Equipment Interfaces.
Industrial Serial Control Equipment
The ADM207EARS fits industrial controllers that need several legacy RS-232 ports but cannot provide separate ±12 V rails. Its five drivers can command up to five external devices, while three receivers can monitor acknowledgments, status indicators, or handshake signals. Running from a single 5 V supply simplifies the power tree, and the 230 kbps capability supports established UART-based industrial protocols. The EIA-232E and CCITT V.28 conformance makes it appropriate for equipment built around conventional RS-232 electrical behavior. Designers should still evaluate transient protection and grounding because the ±15 kV ESD rating applies to the interface device rather than the complete connector, cable, and enclosure system.
موصى به
Data Acquisition Systems
The ADM207EARS is suitable for data-acquisition controllers that must bridge modern CMOS logic to several RS-232 instruments. Five driver channels allow multiple measurement devices or legacy adapters to share one controller, and three receiver channels can collect command acknowledgments or interlock signals. Its single 5 V operation reduces supply complexity in compact acquisition equipment, while the 230 kbps maximum rate is more than sufficient for many short asynchronous control links. The 24-pin SSOP keeps the interface compact but requires careful routing of driver outputs away from sensitive measurement circuitry. Confirm grounding and isolation strategy for each instrument to avoid injecting ground noise into the analog acquisition channels.
موصى به
Test and Measurement Instruments
The ADM207EARS can provide the RS-232 connectivity found in programmable laboratory instruments and automated test equipment. Its five transmitters support commands for multiple instruments, and its three receivers can handle acknowledgments, status outputs, or remote trigger signals. The 230 kbps data rate supports common legacy instrument-control protocols, while EIA-232E and V.28 conformance help maintain consistent electrical behavior across the interface. Use short, properly terminated cable runs and verify connector pin assignments for each instrument because standards-compliant transceivers do not guarantee that every legacy device uses the same signal-to-connector mapping. Add appropriate surge protection when test leads leave the enclosure.
موصى به
Point-of-Sale Terminals
The ADM207EARS is suitable for point-of-sale terminals and peripherals that retain multiple RS-232 ports for printers, scanners, card-reader accessories, or service equipment. Five driver channels can support several unidirectional peripheral links, and three receiver channels can monitor equipment status. The single 5 V supply is useful where product designers want to avoid an additional bipolar power rail, and the 230 kbps rate accommodates conventional serial peripheral interfaces. Because retail equipment may be connected to user-accessible cables, the specified ±15 kV ESD protection is valuable. The final design should still include enclosure grounding, connector shielding, and system-level surge protection rather than relying on the transceiver alone.
موصى به
Communication Port Expanders
The ADM207EARS can expand a UART-based embedded controller into a multi-port RS-232 interface. One processor can use the five transmitter channels to address several remote nodes, while the three receivers provide return paths for acknowledgments or status. Its single 5 V operation pairs well with CMOS control logic, and the 24-pin SSOP package avoids a large connector-style interface footprint. The 230 kbps maximum rate is appropriate for legacy supervisory or configuration links, though it does not replace a modern high-speed serial standard. Firmware must also handle direction control manually because the ADM207EARS is a fixed multi-driver, multi-receiver interface rather than an automatically directed transceiver.
موصى به
Legacy Equipment Interfaces
The ADM207EARS provides a practical bridge between modern CMOS logic and legacy equipment that still exposes EIA-232E ports. A single controller can operate five command outputs and monitor three response lines without requiring five separate driver packages. Its single 5 V supply and 0.1 µF charge-pump capacitor arrangement simplify implementation compared with discrete RS-232 level shifters. The 230 kbps rate covers many established control protocols, and the ±15 kV ESD rating improves robustness in electrically noisy environments. Before integrating a legacy device, verify its connector wiring, signal polarity, handshake timing, and whether the cable requires an additional ground or shielding arrangement.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ADM207EARS — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | ADM207EARSZ | MAX207CDB |
|---|---|---|---|
| Package | 24-pin SSOP | 24-pin SSOP | 24-pin SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Driver Channels | 5 channels | 5 channels | 5 channels |
| Receiver Channels | 3 channels | 3 channels | 3 channels |
| Supply Voltage | 5 V | 5 V | 5 V |
| Maximum Data Rate | 230 kbps | 230 kbps | 230 kbps |
أبرز الفروقات
- Five drivers support multiport RS-232 control (مقابلMAX207CDB)
- Single 5 V charge-pump interface (مقابلADM207EARSZ)
- RS-232 standards support for legacy equipment (مقابلMAX207CDB)
- Specified electrostatic-discharge robustness (مقابلMAX207CDB)
ملاحظات التصميم
Place the specified 0.1 µF charge-pump capacitor directly between the charge-pump pins and the package ground reference. Keep this connection short because long traces can increase charge-pump transient current and radiated noise. Route each RS-232 driver output directly toward its connector-side protection network, and keep these traces physically separated from receiver inputs, clock signals, and sensitive analog circuitry.
Do not treat the UART TX and RX pins as direct RS-232 signals. The ADM207EARS driver channels require the correct DB9 connector assignment, including the relevant signal and ground conductors, while the receiver inputs must be connected to compatible RS-232 outputs. Also verify whether the selected legacy equipment uses hardware handshaking; unused driver or receiver channels should remain properly terminated according to the manufacturer application guidance.
RS-232 driver outputs can radiate noise when they transition between positive and negative signal levels. Keep connector paths short, provide a solid chassis or signal-ground return, and place any external protection components near the connector. The integrated ±15 kV ESD protection helps at the IC level, but cable transients and industrial surges require a separate system-level protection strategy.
The 230 kbps rating is a device capability, not a guarantee that every attached cable and peripheral will operate at that rate. Validate line capacitance, cable length, grounding, and the connected equipment's timing requirements. For a replacement, compare enable, shutdown, receiver enable, and charge-pump pin functions rather than checking only the driver and receiver counts.
معلومات الامتثال
The ADM207E product page identifies EIA-232E and CCITT V.28 conformity and ±15 kV ESD protection, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations are shown for the exact ADM207EARS ordering code.