Analog Devices

ADM207EARS - 5/3 RS-232 Transceiver | Analog Devices

MPN: ADM207EARS ✓ Active
5 V Vdss 24-pin SSOP Package
MOQ: 1 |

ADM207EARS Overview

Analog Devices ADM207EARS is a 5-driver, 3-receiver RS-232 transceiver operating from a single 5 V supply at rates up to 230 kbps, and it is packaged in a 24-pin SSOP. The ADM2xxE interface family targets EIA-232E and CCITT V.28 equipment where external ±12 V rails are unavailable.

An RS-232 transceiver combines line drivers and line receivers on one integrated circuit. Digital logic-side signals enter the receivers and leave the drivers, while the external RS-232 ports use bipolar voltage signaling. The ADM207EARS therefore serves as the interface between low-voltage CMOS equipment and a physical RS-232 connection. It belongs to the RS-232 transceiver hierarchy alongside line drivers, line receivers, and multi-driver interface ICs.

Five driver channels allow one controller to connect to five external RS-232 ports, while three receiver channels can monitor three incoming data lines. Operation from a single 5 V supply simplifies system power design, and the specified 0.1 µF charge-pump capacitor requirement reduces external power-supply complexity. The device supports data rates to 230 kbps and is designed for robust communications interfaces.

The ADM207E family is intended for EIA-232E and CCITT V.28 signaling applications. According to the Analog Devices product page, it is suitable for harsh electrical environments and includes ESD protection rated at ±15 kV. These protections are important when equipment cables connect to user-accessible ports, where electrostatic discharge and transient events can otherwise damage the interface IC.

Typical uses include industrial serial-control equipment, data acquisition systems, instrumentation, POS terminals, and communications adapters. The five transmitters are useful in multiport controller designs, while the three receivers support status, handshake, or acknowledgment inputs. The 230 kbps maximum data rate supports legacy synchronous and asynchronous RS-232 links used in industrial control, test equipment, and embedded systems.

Layout should preserve short charge-pump paths and return the charge-pump capacitor close to the device. RS-232 driver outputs should also be isolated from sensitive analog inputs, and external protection may be needed for long cables or severe industrial transients. Confirm connector-level signaling and grounding before treating a logic-level UART connection as a complete RS-232 interface.

This page combines the manufacturer interface specifications, exact package and channel information, sourcing guidance, and a practical comparison with confirmed 24-SSOP alternatives. It also highlights the design checks that matter when replacing a multi-channel RS-232 transceiver without changing the PCB footprint.

Drop-in alternatives for ADM207EARS — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

ADM207EARSZ

✅ Drop-In
📦 24-pin SSOP
Related ADM207E ordering code with the same 5-driver, 3-receiver RS-232 configuration and 24-SSOP footprint; suffix-specific ordering or qualification details require confirmation.

📋 Reference alternative (not in catalog)

MAX207CDB

✅ Drop-In
📦 24-pin SSOP
Same 5 V supply, five drivers, three receivers, 230 kbps class, and 24-SSOP package; enable and shutdown behavior must be checked against the ADM207EARS pin functions.

📋 Reference alternative (not in catalog)

ADM207EARS Specifications

Product Type RS-232 transceiver
Driver Channels 5 channels
Receiver Channels 3 channels
Supply Voltage 5 V
Maximum Data Rate 230 kbps
Logic Compatibility +5 V CMOS
Charge-Pump Capacitor 0.1 µF
Package 24-pin SSOP
Mounting Type Surface mount
RS-232 Compliance EIA-232E
V.28 Compliance CCITT V.28
ESD Protection ±15 kV
Driver Output Type RS-232 line driver
Receiver Input Type RS-232 line receiver
Production Status Production

ADM207EARS 24-pin ssop Pin Configuration Guide

Pin configuration for ADM207EARS (24-pin ssop package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

24-pin ssop package pinout diagram for ADM207EARS

No detailed pinout data available for ADM207EARS.

Refer to the datasheet for full pin configuration.

Typical Applications

ADM207EARS is suitable for 6 applications: Industrial Serial Control Equipment, Data Acquisition Systems, Test and Measurement Instruments, Point-of-Sale Terminals, Communication Port Expanders, Legacy Equipment Interfaces.

🏭

Industrial Serial Control Equipment

The ADM207EARS fits industrial controllers that need several legacy RS-232 ports but cannot provide separate ±12 V rails. Its five drivers can command up to five external devices, while three receivers can monitor acknowledgments, status indicators, or handshake signals. Running from a single 5 V supply simplifies the power tree, and the 230 kbps capability supports established UART-based industrial protocols. The EIA-232E and CCITT V.28 conformance makes it appropriate for equipment built around conventional RS-232 electrical behavior. Designers should still evaluate transient protection and grounding because the ±15 kV ESD rating applies to the interface device rather than the complete connector, cable, and enclosure system.

📡

Data Acquisition Systems

The ADM207EARS is suitable for data-acquisition controllers that must bridge modern CMOS logic to several RS-232 instruments. Five driver channels allow multiple measurement devices or legacy adapters to share one controller, and three receiver channels can collect command acknowledgments or interlock signals. Its single 5 V operation reduces supply complexity in compact acquisition equipment, while the 230 kbps maximum rate is more than sufficient for many short asynchronous control links. The 24-pin SSOP keeps the interface compact but requires careful routing of driver outputs away from sensitive measurement circuitry. Confirm grounding and isolation strategy for each instrument to avoid injecting ground noise into the analog acquisition channels.

🔧

Test and Measurement Instruments

The ADM207EARS can provide the RS-232 connectivity found in programmable laboratory instruments and automated test equipment. Its five transmitters support commands for multiple instruments, and its three receivers can handle acknowledgments, status outputs, or remote trigger signals. The 230 kbps data rate supports common legacy instrument-control protocols, while EIA-232E and V.28 conformance help maintain consistent electrical behavior across the interface. Use short, properly terminated cable runs and verify connector pin assignments for each instrument because standards-compliant transceivers do not guarantee that every legacy device uses the same signal-to-connector mapping. Add appropriate surge protection when test leads leave the enclosure.

🖥️

Point-of-Sale Terminals

The ADM207EARS is suitable for point-of-sale terminals and peripherals that retain multiple RS-232 ports for printers, scanners, card-reader accessories, or service equipment. Five driver channels can support several unidirectional peripheral links, and three receiver channels can monitor equipment status. The single 5 V supply is useful where product designers want to avoid an additional bipolar power rail, and the 230 kbps rate accommodates conventional serial peripheral interfaces. Because retail equipment may be connected to user-accessible cables, the specified ±15 kV ESD protection is valuable. The final design should still include enclosure grounding, connector shielding, and system-level surge protection rather than relying on the transceiver alone.

🌐

Communication Port Expanders

The ADM207EARS can expand a UART-based embedded controller into a multi-port RS-232 interface. One processor can use the five transmitter channels to address several remote nodes, while the three receivers provide return paths for acknowledgments or status. Its single 5 V operation pairs well with CMOS control logic, and the 24-pin SSOP package avoids a large connector-style interface footprint. The 230 kbps maximum rate is appropriate for legacy supervisory or configuration links, though it does not replace a modern high-speed serial standard. Firmware must also handle direction control manually because the ADM207EARS is a fixed multi-driver, multi-receiver interface rather than an automatically directed transceiver.

🔌

Legacy Equipment Interfaces

The ADM207EARS provides a practical bridge between modern CMOS logic and legacy equipment that still exposes EIA-232E ports. A single controller can operate five command outputs and monitor three response lines without requiring five separate driver packages. Its single 5 V supply and 0.1 µF charge-pump capacitor arrangement simplify implementation compared with discrete RS-232 level shifters. The 230 kbps rate covers many established control protocols, and the ±15 kV ESD rating improves robustness in electrically noisy environments. Before integrating a legacy device, verify its connector wiring, signal polarity, handshake timing, and whether the cable requires an additional ground or shielding arrangement.

Recommended Products Summary

MAX207CDB Five-driver, three-receiver RS-232 interface alternative Used in: Industrial Serial Control Equipment, Data Acquisition Systems, Test and Measurement Instruments, Point-of-Sale Terminals, Communication Port Expanders, Legacy Equipment Interfaces ADM207EARSZ Closely related ADM207E 24-SSOP interface ordering code Used in: Industrial Serial Control Equipment, Data Acquisition Systems, Test and Measurement Instruments, Point-of-Sale Terminals, Communication Port Expanders, Legacy Equipment Interfaces
What is the ADM207EARS?
The ADM207EARS is a 5 V, single-supply RS-232 transceiver containing five line drivers and three line receivers for data rates up to 230 kbps. Analog Devices identifies the ADM2xxE family as an EIA-232E and CCITT V.28 interface solution for equipment where external ±12 V supplies are not available. The target device uses a 24-pin SSOP and requires a 0.1 µF charge-pump capacitor.
What are the key specifications of ADM207EARS that engineers should know?
The ADM207EARS combines five RS-232 drivers, three receivers, a single 5 V supply, and a maximum data rate of 230 kbps in a 24-pin SSOP. According to the Analog Devices ADM207E product page, the device conforms to EIA-232E and CCITT V.28 and provides ±15 kV ESD protection. Its charge-pump architecture generates the bipolar voltage required for RS-232 signaling without a separate ±12 V supply.
How many RS-232 drivers and receivers does ADM207EARS have?
The ADM207EARS has five RS-232 driver outputs and three receiver inputs. This channel arrangement allows one controller to communicate with as many as five external RS-232 ports while monitoring three incoming signals such as acknowledgments, status lines, or handshake inputs. The DigiKey product listing identifies the part as a 5/3 full RS-232 transceiver.
What is the maximum data rate of ADM207EARS?
The ADM207EARS supports RS-232 data rates up to 230 kbps. Analog Devices states that the ADM207E family conforms to the EIA-232E and CCITT V.28 specifications and operates from a single 5 V supply. This rate is suitable for established asynchronous UART links and synchronous serial-control interfaces, although cable length and signaling conditions must also follow RS-232 practice.
What supply voltage does ADM207EARS use?
The ADM207EARS operates from a single 5 V supply. The Analog Devices ADM207E overview identifies the ADM2xxE devices as +5 V CMOS RS-232 interface circuits capable of operation at 230 kbps. This single-supply architecture simplifies board-level power design, while the integrated charge pump provides the voltage conversion needed for RS-232 driver outputs.
Does ADM207EARS support EIA-232E and V.28?
Yes, the ADM207EARS supports EIA-232E and CCITT V.28 operation. The Analog Devices ADM207E product page explicitly identifies conformance with both specifications. These standards define the electrical behavior used by the RS-232 drivers and receivers, allowing the interface to be used with compatible legacy serial equipment.
What ESD protection does ADM207EARS provide?
The ADM207EARS is specified with ±15 kV ESD protection. According to the ADM207EARS datasheet information, the interface is designed for EMI/EMC-compliant RS-232 line drivers and receivers, and the Analog Devices family overview identifies it as suitable for harsh electrical environments. Protection ratings should still be checked against the complete system's connector and enclosure design.
Where can I download the ADM207EARS datasheet PDF?
The official Analog Devices ADM207E product page provides the manufacturer documentation for the ADM207E family, including the ADM207EARS 24-pin SSOP configuration. Use the manufacturer product page at analog.com to obtain the current datasheet and ordering information. The page identifies Data Sheet Rev. D, so engineers should use that revision when checking limits and application details.
Where can I find the ADM207EARS pinout?
The ADM207EARS pinout is shown in the pin-description and package-drawing sections of the Analog Devices ADM207E datasheet. The device is a 24-pin SSOP, so the package drawing is necessary to associate each driver, receiver, supply, ground, and charge-pump connection with its physical pin. Use the datasheet pin-description table when assigning PCB tracks.
Where can I buy ADM207EARS online?
The ADM207EARS can be requested through the Request a Quote form on this page. The form is the appropriate route for current commercial terms, quantity availability, and lead-time confirmation. The manufacturer lists the ADM207 family as production, and the target ordering code identifies a 24-pin SSOP configuration with five drivers and three receivers.
Is ADM207EARS in stock and what is its lead time?
Current ADM207EARS stock and lead time should be confirmed through the Request a Quote form on this page. Analog Devices identifies the ADM207 family as production, but production status does not by itself guarantee immediate inventory or a fixed delivery interval. Submit the required quantity, packaging preference, and target schedule with the request.
What is the price of ADM207EARS?
The current ADM207EARS commercial price is shown through the Request a Quote form on this page. The form allows the quantity and sourcing request to be evaluated against current channel conditions without publishing a potentially stale figure. The manufacturer identifies ADM207EARS as a production part in a 24-pin SSOP package.
Is ADM207EARS the same as ADM207EARSZ?
The ADM207EARS and ADM207EARSZ are closely related Analog Devices order codes for the ADM207E interface family, and both are associated with the 24-pin SSOP implementation in the available product information. The suffix can encode production, environmental, or packaging distinctions, so engineers must compare the specific ordering codes in the manufacturer table rather than assuming every electrical detail is identical.
Can MAX207CDB replace ADM207EARS?
The MAX207CDB can serve as a 24-SSOP RS-232 alternative when its logic levels, supply range, enable behavior, and channel mapping match the ADM207EARS design. The available cross-reference information identifies it as a functional, pin-compatible replacement in common 5 V RS-232 applications, with five drivers, three receivers, and operation to 230 kbps. Verify the complete pin description before production substitution.
What is the best drop-in replacement for ADM207EARS?
The best drop-in replacement is the confirmed 24-SSOP candidate whose pin mapping, supply range, enable inputs, and channel functions match the ADM207EARS. ADM207EARSZ is the closest same-manufacturer ordering option, while MAX207CDB is a cross-reference candidate for common 5 V RS-232 designs. No verified five-part set of interchangeable alternatives was identified, so each substitution requires a manufacturer pinout comparison.
ADM207EARS vs MAX207CDB: which is better for an industrial controller?
The ADM207EARS and MAX207CDB both support a 5 V RS-232 interface with five drivers, three receivers, and operation up to 230 kbps, making them close candidates for a 24-SSOP controller design. Choose the ADM207EARS when its Analog Devices family documentation and local qualification are preferred; choose the MAX207CDB when its availability or procurement terms are better. Verify enable, shutdown, and exact pin-level behavior before substitution.
When should I choose ADM207EARS over another RS-232 transceiver?
Choose the ADM207EARS when a design requires five RS-232 transmitters, three receivers, a single 5 V supply, EIA-232E and V.28 conformance, and a 24-pin SSOP footprint. It is especially suitable when channel count and 230 kbps operation are more important than adding low-power shutdown or automatic transceiver direction control. The ADM207E product page should be used to confirm electrical limits for the final operating environment.

Engineering reference data for ADM207EARS — comparison, design guidance, and compliance information.

Selection Guide

Choose the ADM207EARS when a 24-pin SSOP RS-232 interface requires five drivers, three receivers, a single 5 V supply, operation to 230 kbps, and compatibility with EIA-232E and CCITT V.28 equipment. It is a strong fit for industrial controllers, data-acquisition systems, and legacy test equipment where several serial ports must be implemented in a limited board area. ADM207EARSZ is the closest related manufacturer ordering code and should be selected when its specific suffix, environmental, or packaging terms better match the design. MAX207CDB is a credible 24-SSOP drop-in candidate for common 5 V applications, but enable, shutdown, and exact pin functions require verification before replacing the target. Neither candidate should be substituted solely from channel count; check the manufacturer pin-description table, operating limits, qualification requirements, and connector-side implementation.

Comparison with Alternatives

Parameter This Product ADM207EARSZ MAX207CDB
Package 24-pin SSOP 24-pin SSOP 24-pin SSOP
Brand Analog Devices Analog Devices Analog Devices
Driver Channels 5 channels 5 channels 5 channels
Receiver Channels 3 channels 3 channels 3 channels
Supply Voltage 5 V 5 V 5 V
Maximum Data Rate 230 kbps 230 kbps 230 kbps

Key Differentiators

  • Five drivers support multiport RS-232 control (vs MAX207CDB)
  • Single 5 V charge-pump interface (vs ADM207EARSZ)
  • RS-232 standards support for legacy equipment (vs MAX207CDB)
  • Specified electrostatic-discharge robustness (vs MAX207CDB)

Design Notes

Place the specified 0.1 µF charge-pump capacitor directly between the charge-pump pins and the package ground reference. Keep this connection short because long traces can increase charge-pump transient current and radiated noise. Route each RS-232 driver output directly toward its connector-side protection network, and keep these traces physically separated from receiver inputs, clock signals, and sensitive analog circuitry.

Do not treat the UART TX and RX pins as direct RS-232 signals. The ADM207EARS driver channels require the correct DB9 connector assignment, including the relevant signal and ground conductors, while the receiver inputs must be connected to compatible RS-232 outputs. Also verify whether the selected legacy equipment uses hardware handshaking; unused driver or receiver channels should remain properly terminated according to the manufacturer application guidance.

RS-232 driver outputs can radiate noise when they transition between positive and negative signal levels. Keep connector paths short, provide a solid chassis or signal-ground return, and place any external protection components near the connector. The integrated ±15 kV ESD protection helps at the IC level, but cable transients and industrial surges require a separate system-level protection strategy.

The 230 kbps rating is a device capability, not a guarantee that every attached cable and peripheral will operate at that rate. Validate line capacitance, cable length, grounding, and the connected equipment's timing requirements. For a replacement, compare enable, shutdown, receiver enable, and charge-pump pin functions rather than checking only the driver and receiver counts.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The ADM207E product page identifies EIA-232E and CCITT V.28 conformity and ±15 kV ESD protection, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations are shown for the exact ADM207EARS ordering code.

Data verified on: 2026-11-14 — data verified and curated by XAIPART's component engineering team

Related Searches

ADM207EARS datasheet ADM207EARS datasheet pdf ADM207EARS pinout ADM207EARS replacement ADM207EARS equivalent ADM207EARS drop-in substitute ADM207EARS cross reference ADM207EARS vs MAX207CDB ADM207EARS price ADM207EARS stock Analog Devices ADM207EARS ADM207EARS 24-SSOP pinout ADM207EARS RS-232 application circuit

Related Components & Terms

Analog Devices ADM207EARS ADM207EARSZ MAX207CDB RS-232 transceiver RS-232 line driver RS-232 line receiver EIA-232E CCITT V.28 CMOS 5 V power supply 230 kbps 24-pin SSOP SSOP package family surface mount charge-pump capacitor 0.1 µF capacitor ±15 kV ESD protection industrial serial control data acquisition system test and measurement equipment legacy equipment interface EMI/EMC compliance interface IC
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details