Analog Devices

ADM238LAR - 4-Channel 5V RS-232 Transceiver | Analog Devices

MPN: ADM238LAR ✓ نشط
5 V Vdss ≤1 µA Id 24-pin SOIC Package
الحد الأدنى للطلب: 1 |

ADM238LAR نظرة عامة

The Analog Devices ADM238LAR is a four-channel, four-transmitter and four-receiver RS-232 interface transceiver operating from a single 5 V supply. It supports data rates up to 120 kbps, generates approximately ±9 V output swings through on-board DC-DC converters, and is packaged in a 24-pin SOIC. The integrated charge-pump design eliminates the need for an external ±12 V supply, making the device suitable for compact single-board serial interfaces.

An RS-232 transceiver belongs to the interface IC hierarchy, where it converts logic-level signals between a host or controller and a cable-based communications port. Unlike a direct TTL serial connection, an RS-232 interface uses unbalanced differential voltage signaling, greater noise tolerance, and inverting line levels. The ADM238LAR integrates four drivers and four receivers so one package can support multiple serial channels while preserving a compact board footprint.

Key operating characteristics include compliance with EIA-232-E and V.28 interface requirements, a maximum data rate of 120 kbps, and receiver input protection extending to ±30 V. Its on-board converters permit approximately ±9 V output swing from a 5 V supply, while small 1 µF charge-pump capacitors simplify the external power-supply network. A shutdown function reduces supply current to no more than 1 µA and allows the receivers to remain active during shutdown.

The ADM238LAR combines CMOS-compatible logic interfacing with integrated isolated-looking charge-pump conversion, although the interface ground remains part of the circuit and should not be interpreted as galvanic isolation. The ±30 V receiver tolerance improves robustness when a connected RS-232 port can experience ±12 V, ±15 V, or other elevated voltage levels. Latch-up-free operation further supports dependable behavior in electrically noisy equipment.

Typical applications include industrial control consoles, test and measurement equipment, POS terminals, instrumentation links, and embedded systems that require several RS-232 ports without a separate negative supply rail. In multiport designs, each transmitter and receiver can be assigned to a different cable or peripheral, while the common 5 V supply simplifies system power architecture. Care is still required to control cable transients and maintain an appropriate common-mode relationship between connected equipment.

For PCB implementation, place the charge-pump capacitors close to their associated pins and route each RS-232 line away from clocks, data buses, and switching-power nodes. Add suitable input protection for long or exposed cables, and verify the logic polarity of each receiver output against the firmware protocol. These practices preserve the device's low-voltage operation while improving field reliability.

This product page organizes the ADM238LAR's core electrical characteristics, drop-in alternatives, application guidance, pin-package considerations, and design checks into one engineering reference. It supports component selection, schematic review, and PCB planning for single-supply RS-232 interfaces operating at up to 120 kbps.

بدائل مباشرة لـ ADM238LAR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع ADM238LAR (نفس عامل الشكل والبصمة) — يختلف في Maximum Data Rate, Package, Product Type.

Analog Devices
Maximum Data Rate: 120 kB/s
Package: 20-lead SSOP
Product Type: 5 V-powered CMOS RS-232 drivers/receivers
قارن مع ADM238LAR →

ADM238LJRZ

✅ بديل مباشر
📦 24-pin SOIC
Same ADM238L family and 24-pin SOIC format; temperature grade and ordering suffix differ by 0% in the compared core function

📋 بديل مرجعي (غير موجود في الكتالوج)

HIN238CB

✅ بديل مباشر
📦 24-pin SOIC
Four-channel 5 V RS-232 function in a 24-pin SOIC; exact data-rate and shutdown differences are not quantified in the comparison listing

📋 بديل مرجعي (غير موجود في الكتالوج)

ADM238LAR المواصفات

Product Type RS-232 transceiver
Number of Transmitters 4
Number of Receivers 4
جهد التغذية 5 V
Maximum Data Rate 120 kbps
RS-232 Output Swing ±9 V
Charge-Pump Capacitor Value 1 µF
Shutdown Supply Current ≤1 µA
Receiver Input Voltage Range ±30 V
Receiver Shutdown Behavior Receivers active in shutdown
Interface Compliance EIA-232-E and V.28
Integrated Power Conversion On-board DC-DC converters
Latch-Up Protection Latch-up free
العلبة 24-pin SOIC
نوع التركيب Surface mount

دليل تكوين أطراف ADM238LAR 24-pin soic

تكوين الأطراف لـ ADM238LAR (حزمة 24-pin soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 24-pin soic لـ ADM238LAR

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ADM238LAR.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ADM238LAR مناسب لـ 6 التطبيقs: Industrial Control Console, Test and Measurement Equipment, Point-of-Sale Terminal, Embedded Serial Gateway, Instrumentation Network Node, Telecommunications Control Module.

🏭

Industrial Control Console

The ADM238LAR fits an industrial console that must connect several controllers, meters, or service ports while using only a 5 V supply. Four integrated drivers and receivers reduce the number of interface packages, while the on-board DC-DC converters produce approximately ±9 V output swing without an external negative rail. At the 120 kbps maximum data rate, it suits supervisory and diagnostic channels rather than high-speed storage links. Place the 1 µF charge-pump capacitors near the IC and route cable-side traces away from switching nodes.

🔧

Test and Measurement Equipment

The ADM238LAR is useful in test and measurement instruments that expose several legacy serial ports for probes, fixtures, and legacy peripherals. A single 5 V rail simplifies the instrument power tree, and the integrated converters remove the need for a separate ±12 V supply. Its four transmitters and four receivers support multiple independent directions without adding four single-channel packages. Preserve the EIA-232-E and V.28 system-level design conventions, including cable protection and controlled reference grounding.

🖥️

Point-of-Sale Terminal

A point-of-sale terminal can use the ADM238LAR to interface a printer, customer display, scanner, or service connector that retains an RS-232 port. Four-channel integration is valuable where the enclosure must remain compact and powered from a regulated 5 V rail. The 120 kbps rate is more than adequate for many peripheral control protocols, while ±30 V receiver tolerance improves robustness against raised RS-232 levels. Add connector-side transient protection when cables leave the enclosure.

🧩

Embedded Serial Gateway

The ADM238LAR can bridge a controller or embedded system to several RS-232 field devices in a compact gateway. Its 5 V-only operation is useful where power density is constrained, and integrated DC-DC conversion avoids distributing a bipolar supply. The four transmitters and receivers allow the gateway to support multiple external devices or provide spare channels for configuration and diagnostics. Validate protocol timing and cable length, and place protection components at exposed connectors rather than relying solely on the receiver's ±30 V tolerance.

📡

Instrumentation Network Node

The ADM238LAR suits an instrumentation node that connects sensors, programmable instruments, or service equipment using RS-232. Its approximately ±9 V driver swing meets the cited EIA-232-E and V.28 requirements from a single 5 V supply, reducing the number of power rails in field equipment. At up to 120 kbps, it is appropriate for command, status, and measurement-control traffic. Maintain short charge-pump connections and separate protected cable routing from sensitive analog and processor circuits.

🌐

Telecommunications Control Module

The ADM238LAR can support service-console and legacy-network connections within a telecommunications control module. Four RS-232 channels provide flexible allocation among configuration tools, line cards, or local test equipment, while the 5 V supply requirement simplifies power distribution in dense equipment. The device is not a galvanic isolation barrier, so cable-side and logic-side grounding must follow the telecommunications system's interface design. Use suitable line protection when ports connect to long or outdoor cables.

ملخص المنتجات الموصى بها

ADM238LAR Analog Devices يُستخدم في: Industrial Control Console, Test and Measurement Equipment, Point-of-Sale Terminal, Embedded Serial Gateway, Instrumentation Network Node, Telecommunications Control Module ADM238LJRZ Same-family alternative with different ordering suffix يُستخدم في: Industrial Control Console, Test and Measurement Equipment, Embedded Serial Gateway, Telecommunications Control Module HIN238CB Potential alternate four-channel RS-232 transceiver يُستخدم في: Point-of-Sale Terminal, Instrumentation Network Node
What are the key specifications of ADM238LAR that engineers should know?
The ADM238LAR is a four-transmitter, four-receiver RS-232 transceiver built around a single 5 V supply. According to the manufacturer datasheet, it supports data rates up to 120 kbps, produces approximately ±9 V output swings using on-board DC-DC converters, accepts receiver inputs up to ±30 V, and requires only 1 µF charge-pump capacitors. The device also meets EIA-232-E and V.28 requirements, supports shutdown current of no more than 1 µA, and comes in a 24-pin SOIC.
Where to download the ADM238LAR datasheet PDF?
The ADM238LAR datasheet can be downloaded from the Analog Devices documentation link listed on this page or from the manufacturer-hosted PDF mirrored in the product references. It describes the electrical characteristics, RS-232 interface behavior, DC-DC converter implementation, shutdown mode, and package pin assignments. Use the manufacturer datasheet as the controlling document for wiring, maximum ratings, capacitance values, and operating limits.
Where can I find the ADM238LAR pinout and package information?
The ADM238LAR uses a 24-pin SOIC package, and its complete numbered pin assignment is shown in the pin configuration and pin-description tables in the manufacturer datasheet. Assign signal and supply connections directly from those tables rather than inferring positions from a generic 24-pin footprint. Check the exposed device orientation, ground pins, charge-pump capacitor pins, receiver inputs, and transmitter outputs before releasing a PCB layout.
Can the ADM238LAR operate without a negative supply voltage?
Yes. The ADM238LAR operates from one 5 V supply because its on-board DC-DC converters generate the bipolar voltage needed by the RS-232 drivers. The resulting output swing is approximately ±9 V, allowing the device to meet EIA-232-E and V.28 requirements without external ±12 V rails. This simplifies power distribution in compact systems, although normal signal-ground and cable-routing practices still apply.
What is the maximum data rate of the ADM238LAR?
The ADM238LAR supports a maximum RS-232 data rate of 120 kbps. This rate applies across its integrated transmitter and receiver channels while the device is powered from 5 V. The manufacturer datasheet also specifies the required 1 µF charge-pump capacitors and the complete electrical test conditions. For reliable communication, preserve signal integrity between the logic side and the external RS-232 connector.
Is the ADM238LAR suitable for industrial control and instrumentation?
The ADM238LAR is well suited to industrial control and instrumentation systems that need several RS-232 ports from one 5 V rail. Its integrated ±9 V driver swing eliminates a separate negative supply, while ±30 V receiver tolerance provides additional robustness against elevated RS-232 levels. The four-channel configuration reduces package count and board area compared with several separate single-channel transceivers.
What is the difference between ADM238LAR and ADM238LJRZ?
ADM238LAR and ADM238LJRZ belong to the same Analog Devices ADM238L family and provide four RS-232 drivers and four receivers from a 5 V supply. Their ordering codes can differ in temperature grade, packaging, or delivery format. Verify the exact suffix against the manufacturer ordering guide and inspect the package drawing before treating one as a substitute for the other.
What can replace the ADM238LAR in an RS-232 design?
The ADM238LJRZ is the closest same-family alternative identified for the ADM238LAR, but its exact temperature grade and package suffix must be checked before substitution. HIN238CB also appears in cross-reference listings, although it is manufactured by Rochester Electronics rather than Analog Devices. Confirm pinout, supply voltage, shutdown behavior, receiver tolerance, and package dimensions against both manufacturers' datasheets before approving a replacement.
Is the HIN238CB a drop-in replacement for the ADM238LAR?
The HIN238CB is a potential four-channel RS-232 alternative, but it should not be treated as an automatic drop-in replacement. Cross-reference information identifies it as an ADM238LAR comparison part, while the HIN238CB package and electrical details must still be checked against the ADM238LAR. Confirm the 24-pin SOIC footprint, pin mapping, capacitor requirements, data rate, and shutdown behavior before substituting it.
When should I choose the ADM238LAR over another RS-232 transceiver?
Choose the ADM238LAR when a design needs four RS-232 channels, one 5 V supply, and approximately ±9 V driver swing without adding a negative rail. Its 120 kbps maximum data rate suits control, diagnostic, and instrumentation links. Select another device when the interface needs a different channel count, higher data rate, isolated RS-232, automatic shutdown behavior, or a package and pin arrangement not shared by the ADM238LAR.
Is the ADM238LAR suitable for a long exposed RS-232 cable?
The ADM238LAR is electrically suitable for RS-232 links because its receivers tolerate input voltages up to ±30 V and meet EIA-232-E and V.28 requirements. Nevertheless, long exposed cables require additional surge and ESD protection near the connector. Select protection components for the cable's actual transient environment, maintain the recommended grounding strategy, and route protected connector traces away from sensitive logic.
What are the power and thermal considerations for ADM238LAR?
The ADM238LAR is powered by a single 5 V supply, and its shutdown mode reduces supply current to no more than 1 µA. During operation, dissipation includes internal DC-DC converter and logic overhead, so the PCB must provide adequate copper area for heat transfer. Use the manufacturer power-dissipation and maximum junction-temperature guidance, keep exposed-pad or thermal copper continuous where applicable, and avoid enclosing the device in an unventilated enclosure without thermal analysis.
Does the ADM238LAR provide galvanic isolation?
No. The ADM238LAR is a single-supply RS-232 transceiver, not a galvanically isolated interface. Its integrated DC-DC converters generate bipolar driver voltage, but the device does not provide a safety-rated isolation barrier between logic and cable-side circuits. If galvanic isolation is required, choose a dedicated isolated RS-232 transceiver and validate its isolation rating, capacitance, data rate, and power requirements.
How should charge-pump capacitors be placed around the ADM238LAR?
Place the specified 1 µF charge-pump capacitors close to the ADM238LAR pins and keep their return paths short. Follow the exact capacitor type, voltage rating, tolerance, and connection arrangement shown in the manufacturer datasheet and typical application circuit. Avoid placing long capacitor traces beneath or beside adjacent RS-232 signals, and keep high-current switching nodes separated from the charge-pump network.
Where to buy ADM238LAR online and what is its current lead time?
Use the Request a Quote form on this page to request current ADM238LAR availability, lead time, and order quantities. The product is offered by authorized distribution channels, but inventory and lead time can change rapidly and should be confirmed for the exact 24-pin SOIC ordering code. The Request a Quote form allows procurement to specify quantity, target price, and delivery requirements.
How does the ADM238LAR compare with a MAX238CWG+T RS-232 transceiver?
The ADM238LAR is a 24-pin SOIC, four-driver and four-receiver transceiver, while the MAX238CWG+T is listed as a 28-pin device. Because the package pin counts differ, MAX238CWG+T is not a footprint-compatible drop-in replacement for ADM238LAR without a PCB redesign. It may serve a similar functional role, but its voltage rating, shutdown behavior, channel details, and pin arrangement should be reviewed independently.

بيانات مرجعية هندسية لـ ADM238LAR — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the ADM238LAR when a system needs four RS-232 drivers and four receivers, operates from a single 5 V rail, and can use approximately ±9 V driver swing. It is particularly useful in compact industrial, test, POS, gateway, and instrumentation products where an external negative supply would increase design complexity. The ADM238LJRZ is the preferred same-family alternative when its temperature and ordering suffix match the target requirements. HIN238CB may fit a similar multiport function, but confirm its pinout, data rate, shutdown behavior, and electrical limits before substitution. Do not select MAX238CWG+T as a no-change replacement because its 28-pin package differs from the ADM238LAR's 24-pin SOIC. If a design requires galvanic isolation, a higher data rate, fewer channels, or automatic power control, use a transceiver explicitly designed for those requirements.

المقارنة مع البدائل

المعامل هذا المنتج ADM238LJRZ HIN238CB
Package 24-pin SOIC 24-pin SOIC 24-pin SOIC
Brand Analog Devices Analog Devices Rochester Electronics

أبرز الفروقات

  • Four full-duplex RS-232 channels in one package (مقابلHIN238CB)
  • Single 5 V supply with approximately ±9 V driver swing (مقابلHIN238CB)
  • Defined 120 kbps operation and ±30 V receiver tolerance (مقابلADM238LJRZ)

ملاحظات التصميم

Place the specified 1 µF charge-pump capacitors directly beside the associated ADM238LAR pins and keep their current loops compact. Follow the exact capacitor connections shown in the manufacturer typical application circuit. Do not substitute a substantially larger package without checking effective capacitance, bias behavior, ESR, and available board area, because long charge-pump traces can increase radiated noise and reduce startup margin.

Separate the RS-232 connector side from processor clocks, switching-regulator nodes, and sensitive analog inputs. Route each cable-side signal with a continuous reference plane and keep protection components close to the connector. Although the receivers accept input levels up to ±30 V, that rating does not replace surge or ESD protection for cables that leave an enclosure or connect to externally powered equipment.

Do not treat the integrated DC-DC converter as a galvanic isolation barrier. The logic ground, driver ground, and cable-side reference must follow the system grounding plan, particularly when connecting two independently powered systems. Also verify driver polarity and receiver inversion in firmware because RS-232 line levels and logic levels are not directly interchangeable.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The ADM238LAR is an RS-232 interface IC rather than an automotive-qualified component. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the cited product information.

تم التحقق من البيانات في: 2026-11-09 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ADM238LAR datasheet ADM238LAR datasheet pdf ADM238LAR pinout ADM238LAR specifications ADM238LAR equivalent ADM238LAR replacement ADM238LAR vs HIN238CB ADM238LAR vs ADM238LJRZ ADM238LAR price ADM238LAR stock Analog Devices ADM238LAR ADM238LAR 5V RS-232 transceiver ADM238LAR 24-SOIC footprint ADM238LAR industrial control application where to buy ADM238LAR

المكونات والمصطلحات ذات الصلة

Analog Devices ADM238LAR ADM238LJRZ HIN238CB RS-232 transceiver interface IC serial interface CMOS transceiver EIA-232-E V.28 DC-DC converter charge-pump capacitor RS-232 line driver RS-232 receiver 120 kbps ±9 V output swing ±30 V receiver input shutdown mode 24-pin SOIC SOIC family surface-mount package industrial control test and measurement point-of-sale terminal
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر