ADM238LAR - 4-Channel 5V RS-232 Transceiver | Analog Devices
Teilenummer: ADM238LAR ✓ AktivADM238LAR Übersicht
An RS-232 transceiver belongs to the interface IC hierarchy, where it converts logic-level signals between a host or controller and a cable-based communications port. Unlike a direct TTL serial connection, an RS-232 interface uses unbalanced differential voltage signaling, greater noise tolerance, and inverting line levels. The ADM238LAR integrates four drivers and four receivers so one package can support multiple serial channels while preserving a compact board footprint.
Key operating characteristics include compliance with EIA-232-E and V.28 interface requirements, a maximum data rate of 120 kbps, and receiver input protection extending to ±30 V. Its on-board converters permit approximately ±9 V output swing from a 5 V supply, while small 1 µF charge-pump capacitors simplify the external power-supply network. A shutdown function reduces supply current to no more than 1 µA and allows the receivers to remain active during shutdown.
The ADM238LAR combines CMOS-compatible logic interfacing with integrated isolated-looking charge-pump conversion, although the interface ground remains part of the circuit and should not be interpreted as galvanic isolation. The ±30 V receiver tolerance improves robustness when a connected RS-232 port can experience ±12 V, ±15 V, or other elevated voltage levels. Latch-up-free operation further supports dependable behavior in electrically noisy equipment.
Typical applications include industrial control consoles, test and measurement equipment, POS terminals, instrumentation links, and embedded systems that require several RS-232 ports without a separate negative supply rail. In multiport designs, each transmitter and receiver can be assigned to a different cable or peripheral, while the common 5 V supply simplifies system power architecture. Care is still required to control cable transients and maintain an appropriate common-mode relationship between connected equipment.
For PCB implementation, place the charge-pump capacitors close to their associated pins and route each RS-232 line away from clocks, data buses, and switching-power nodes. Add suitable input protection for long or exposed cables, and verify the logic polarity of each receiver output against the firmware protocol. These practices preserve the device's low-voltage operation while improving field reliability.
This product page organizes the ADM238LAR's core electrical characteristics, drop-in alternatives, application guidance, pin-package considerations, and design checks into one engineering reference. It supports component selection, schematic review, and PCB planning for single-supply RS-232 interfaces operating at up to 120 kbps.
Drop-in-Alternativen für ADM238LAR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADM238LAR (gleiche Bauform und Footprint) – abweichend in Maximum Data Rate, Package, Product Type.
ADM238LJRZ
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
HIN238CB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADM238LAR Technische Daten
| Product Type | RS-232 transceiver |
| Number of Transmitters | 4 |
| Number of Receivers | 4 |
| Versorgungsspannung | 5 V |
| Maximum Data Rate | 120 kbps |
| RS-232 Output Swing | ±9 V |
| Charge-Pump Capacitor Value | 1 µF |
| Shutdown Supply Current | ≤1 µA |
| Receiver Input Voltage Range | ±30 V |
| Receiver Shutdown Behavior | Receivers active in shutdown |
| Interface Compliance | EIA-232-E and V.28 |
| Integrated Power Conversion | On-board DC-DC converters |
| Latch-Up Protection | Latch-up free |
| Gehäuse | 24-pin SOIC |
| Montageart | Surface mount |
ADM238LAR 24-pin soic Pinbelegungsleitfaden
Pinbelegung für ADM238LAR (24-pin soic-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für ADM238LAR.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ADM238LAR ist geeignet für 6 Anwendungs: Industrial Control Console, Test and Measurement Equipment, Point-of-Sale Terminal, Embedded Serial Gateway, Instrumentation Network Node, Telecommunications Control Module.
Industrial Control Console
The ADM238LAR fits an industrial console that must connect several controllers, meters, or service ports while using only a 5 V supply. Four integrated drivers and receivers reduce the number of interface packages, while the on-board DC-DC converters produce approximately ±9 V output swing without an external negative rail. At the 120 kbps maximum data rate, it suits supervisory and diagnostic channels rather than high-speed storage links. Place the 1 µF charge-pump capacitors near the IC and route cable-side traces away from switching nodes.
Empfohlen
Test and Measurement Equipment
The ADM238LAR is useful in test and measurement instruments that expose several legacy serial ports for probes, fixtures, and legacy peripherals. A single 5 V rail simplifies the instrument power tree, and the integrated converters remove the need for a separate ±12 V supply. Its four transmitters and four receivers support multiple independent directions without adding four single-channel packages. Preserve the EIA-232-E and V.28 system-level design conventions, including cable protection and controlled reference grounding.
Empfohlen
Point-of-Sale Terminal
A point-of-sale terminal can use the ADM238LAR to interface a printer, customer display, scanner, or service connector that retains an RS-232 port. Four-channel integration is valuable where the enclosure must remain compact and powered from a regulated 5 V rail. The 120 kbps rate is more than adequate for many peripheral control protocols, while ±30 V receiver tolerance improves robustness against raised RS-232 levels. Add connector-side transient protection when cables leave the enclosure.
Empfohlen
Embedded Serial Gateway
The ADM238LAR can bridge a controller or embedded system to several RS-232 field devices in a compact gateway. Its 5 V-only operation is useful where power density is constrained, and integrated DC-DC conversion avoids distributing a bipolar supply. The four transmitters and receivers allow the gateway to support multiple external devices or provide spare channels for configuration and diagnostics. Validate protocol timing and cable length, and place protection components at exposed connectors rather than relying solely on the receiver's ±30 V tolerance.
Empfohlen
Instrumentation Network Node
The ADM238LAR suits an instrumentation node that connects sensors, programmable instruments, or service equipment using RS-232. Its approximately ±9 V driver swing meets the cited EIA-232-E and V.28 requirements from a single 5 V supply, reducing the number of power rails in field equipment. At up to 120 kbps, it is appropriate for command, status, and measurement-control traffic. Maintain short charge-pump connections and separate protected cable routing from sensitive analog and processor circuits.
Empfohlen
Telecommunications Control Module
The ADM238LAR can support service-console and legacy-network connections within a telecommunications control module. Four RS-232 channels provide flexible allocation among configuration tools, line cards, or local test equipment, while the 5 V supply requirement simplifies power distribution in dense equipment. The device is not a galvanic isolation barrier, so cable-side and logic-side grounding must follow the telecommunications system's interface design. Use suitable line protection when ports connect to long or outdoor cables.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADM238LAR – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADM238LJRZ | HIN238CB |
|---|---|---|---|
| Package | 24-pin SOIC | 24-pin SOIC | 24-pin SOIC |
| Brand | Analog Devices | Analog Devices | Rochester Electronics |
Wichtigste Unterscheidungsmerkmale
- Four full-duplex RS-232 channels in one package (vs. HIN238CB)
- Single 5 V supply with approximately ±9 V driver swing (vs. HIN238CB)
- Defined 120 kbps operation and ±30 V receiver tolerance (vs. ADM238LJRZ)
Designhinweise
Place the specified 1 µF charge-pump capacitors directly beside the associated ADM238LAR pins and keep their current loops compact. Follow the exact capacitor connections shown in the manufacturer typical application circuit. Do not substitute a substantially larger package without checking effective capacitance, bias behavior, ESR, and available board area, because long charge-pump traces can increase radiated noise and reduce startup margin.
Separate the RS-232 connector side from processor clocks, switching-regulator nodes, and sensitive analog inputs. Route each cable-side signal with a continuous reference plane and keep protection components close to the connector. Although the receivers accept input levels up to ±30 V, that rating does not replace surge or ESD protection for cables that leave an enclosure or connect to externally powered equipment.
Do not treat the integrated DC-DC converter as a galvanic isolation barrier. The logic ground, driver ground, and cable-side reference must follow the system grounding plan, particularly when connecting two independently powered systems. Also verify driver polarity and receiver inversion in firmware because RS-232 line levels and logic levels are not directly interchangeable.
Compliance-Informationen
The ADM238LAR is an RS-232 interface IC rather than an automotive-qualified component. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the cited product information.