AT90CAN64-15AT1 - 15MHz 64KB CAN AVR MCU | Microchip
MPN: AT90CAN64-15AT1 ✓ نشطAT90CAN64-15AT1 نظرة عامة
An 8-bit AVR microcontroller is a compact reduced-instruction-set computer optimized for embedded control. The AVR architecture executes most instructions in a single clock cycle and provides 32 general-purpose working registers. When combined with an embedded CAN controller, this device belongs to the communication-focused microcontroller hierarchy used for distributed industrial, automotive, and control-system nodes that need deterministic messaging over a multi-node bus.
The AT90CAN64-15AT1 provides 64 KB of program flash, 2 KB of EEPROM, and 4 KB of SRAM according to the Microchip product-page description. Its integrated CAN controller supports CAN 2.0A and CAN 2.0B communication formats. The 53 general-purpose I/O lines support digital interfaces and peripheral functions, while the 15 MHz operating speed provides additional processing headroom for protocol handling, diagnostics, and supervisory control tasks.
The device uses Microchip's AVR architecture with 133 instructions and 32 general-purpose working registers. Its 64-pin TQFP package exposes the GPIO, communication, timing, and programming resources needed for a standalone CAN node. The automotive-oriented ordering code is identified as AEC-Q100 qualified in the component data for AT90CAN64-15AT1, although qualification details should be checked against the exact ordering-code table before production release.
Typical uses include industrial CAN gateways, automotive body and powertrain control modules, elevator and building-control nodes, instrumentation, motor-control supervisory electronics, and diagnostic tools. Its combination of 53 I/O lines, serial peripherals, and CAN support reduces the need for external interface logic in compact embedded controllers.
For PCB design, preserve the manufacturer's recommended decoupling and clock layout, provide programming access for ISP, and route CAN RX and TX with controlled impedance. Check the complete TQFP pin-assignment table in the manufacturer datasheet before assigning multiplexing functions or planning a footprint revision.
This page consolidates the key electrical limits, communication capabilities, pinout considerations, and engineering trade-offs into a practical selection reference for AT90CAN64-15AT1 designs.
بدائل مباشرة لـ AT90CAN64-15AT1 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع AT90CAN64-15AT1 (نفس عامل الشكل والبصمة) — يختلف في Package, Instruction Set, Product Type, CAN Controller, Maximum Clock Speed.
AT90CAN64-15AT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←AT90CAN64-15MT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←AT90CAN64-15MZ
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←AT90CAN64-16MU
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←AT90CAN64-16AU
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←AT90CAN64-15AT1 الحدود القصوى والخصائص الكهربائية
| Product Type | 8-bit AVR RISC microcontroller with CAN controller |
| Maximum Clock Speed | 15 MHz |
| Flash Memory | 64 KB |
| EEPROM Memory | 2 KB |
| SRAM | 4 KB |
| General-Purpose I/O Lines | 53 |
| General-Purpose Working Registers | 32 |
| CAN Controller | CAN 2.0A and CAN 2.0B compliant |
| جهد التغذية | 4.5 V to 5.5 V |
| Instruction Set | 133 instructions |
| Program Memory Features | ISP flash with read-while-write capability |
| عرض ناقل البيانات | 8 bit |
| العلبة | 64-pin TQFP, 14 mm x 14 mm |
| نوع التركيب | Surface mount |
| Automotive Qualification | AEC-Q100 |
| Lifecycle Stage | Active |
دليل تكوين أطراف AT90CAN64-15AT1 64-pin tqfp, 14 mm x 14 mm
تكوين الأطراف لـ AT90CAN64-15AT1 (حزمة 64-pin tqfp, 14 mm x 14 mm). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ AT90CAN64-15AT1.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
AT90CAN64-15AT1 مناسب لـ 6 التطبيقs: Industrial CAN Gateway, Automotive Body Control Module, Elevator and Building Control, Industrial Motor Supervision, CAN Diagnostic and Test Tool, Instrumentation and Sensor Node.
Industrial CAN Gateway
The AT90CAN64-15AT1 fits an industrial CAN gateway because its integrated CAN controller and 53 general-purpose I/O lines can handle communication alongside local supervision functions. Its 15 MHz AVR core provides execution capacity for message filtering, status monitoring, and protocol translation, while 64 KB of flash supports application firmware and 4 KB of SRAM supports short-lived packet and control buffers. The 4.5 V to 5.5 V range supports a conventional embedded supply architecture. In implementation, the MCU connects to a suitable CAN transceiver rather than directly driving the bus, and the PCB should keep decoupling, clock routing, and differential CAN traces tightly controlled.
موصى به
Automotive Body Control Module
The AT90CAN64-15AT1 is appropriate for compact body-control and vehicle-network modules that combine CAN communication with discrete I/O. Its 53 general-purpose I/O lines can connect switches, sensors, indicators, and diagnostic logic without requiring a large external interface device, while the 15 MHz core executes supervisory and debounce routines. The part is identified as an automotive AEC-Q100 configuration, supporting use in electronic control units where qualification status is important. Design engineers should still confirm the exact temperature grade and ordering limits, isolate vehicle transients at the connector and transceiver interfaces, and use hardware watchdog and fail-safe power strategies.
موصى به
Elevator and Building Control
AT90CAN64-15AT1 supports elevator and building-control nodes where distributed CAN communication must coexist with digital input acquisition and actuator control. The combination of 53 I/O lines, 32 working registers, and a 15 MHz AVR core is useful for polling floors, doors, safety switches, and call requests while maintaining a network schedule. Its 2 KB EEPROM can retain small configuration records, although the application must observe the device's endurance and write-cycle guidance. A robust implementation uses an isolated or protected CAN transceiver, local power filtering, and a defined behavior for loss of communication or bus termination faults.
موصى به
Industrial Motor Supervision
The AT90CAN64-15AT1 can serve as the supervisory controller in an industrial motor system where a drive controller communicates over CAN and the supervisory MCU manages interlocks, temperature monitoring, or service diagnostics. Its 53 I/O lines simplify connection of discrete sensors and status signals, and its 15 MHz core can execute control logic concurrently with network tasks. The MCU should remain isolated from high-energy motor wiring, with protection networks handling transients and proper isolation preserving communications integrity. Firmware should include communication-loss timers, safe-state transitions, and deliberate handling of both the 4.5 V and 5.5 V supply boundaries.
موصى به
CAN Diagnostic and Test Tool
AT90CAN64-15AT1 is well suited to compact CAN diagnostic tools because it combines network communication, programmable flash, EEPROM, and abundant GPIO in one package. Engineers can implement message monitoring, fault logging, stimulus sequencing, and external instrument interfacing around the 15 MHz core. The 64 KB flash provides room for protocol handlers and diagnostic firmware, while the CAN controller provides the communication core required to interpret bus traffic. In a portable instrument, attention should be directed to supply regulation, connector protection, and the fact that the MCU requires an external transceiver. Programming and firmware-update access should also be designed into the PCB.
موصى به
Instrumentation and Sensor Node
The AT90CAN64-15AT1 can form a compact instrumentation node that samples digital sensors and publishes measurements through a CAN network. Its 53 general-purpose I/O lines reduce the need for external I/O expansion, while 4 KB of SRAM and 2 KB of EEPROM support temporary data and configuration storage. The 15 MHz AVR core allows measurement acquisition, filtering, and communication tasks to coexist in a single device. Designers should assign peripheral multiplexing from the official TQFP pin table, add analog front-end circuitry separately for non-digital sensors, and apply communication and input protection where field wiring enters the enclosure.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ AT90CAN64-15AT1 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | AT90CAN64-15AT | AT90CAN64-15MT | AT90CAN64-15MZ | AT90CAN64-16MU | AT90CAN64-16AU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) |
| Maximum Clock Speed | 15 MHz | 15 MHz | 15 MHz | 15 MHz | 16 MHz | 16 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| EEPROM Memory | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| General-Purpose I/O Lines | 53 | 53 | 53 | 53 | 53 | 53 |
| Operating Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| CAN Controller | CAN 2.0A and CAN 2.0B compliant | CAN 2.0A and CAN 2.0B compliant | CAN 2.0A and CAN 2.0B compliant | CAN 2.0A and CAN 2.0B compliant | CAN 2.0A and CAN 2.0B compliant | CAN 2.0A and CAN 2.0B compliant |
أبرز الفروقات
- Frequency-matched family option (مقابلAT90CAN64-16MU)
- Integrated CAN and extensive I/O in one controller (مقابلAT90CAN64-16AU)
- On-chip memory supports self-contained embedded nodes (مقابلAT90CAN64-15AT)
ملاحظات التصميم
Place the required bypass capacitors immediately adjacent to the corresponding VCC and AVCC pins, with short ground-return paths to minimize supply inductance. Follow the manufacturer pin-assignment table before assigning multiplexed peripheral functions, because the 64-pin TQFP footprint exposes many alternate signals. Route the clock line away from CAN TX/RX and high-edge-rate switching nodes. Use the package drawing associated with the 64-pin TQFP option rather than adapting a QFN-64 land pattern.
The AT90CAN64-15AT1 requires an external CAN transceiver; connect its CAN RX and TX signals through the transceiver rather than to a physical bus directly. Preserve controlled-impedance CAN routing, provide termination only at appropriate bus locations, and keep the transceiver return path close to its ground reference. For longer or industrial cable runs, add surge and ESD protection at the connector while maintaining the protection network's effect on signal timing and common-mode behavior.
Design the 4.5 V to 5.5 V supply rail to remain inside the operating range at the microcontroller pins, including tolerance, startup overshoot, and transient margin. Check every peripheral and transceiver rail for sequencing conflicts, especially when an ISP programmer or external equipment can back-power the board. Decouple transceiver and regulator outputs separately from sensitive logic nodes, and provide a defined reset state for every rail that participates in CAN-node startup.
Do not infer that the 15 MHz CPU clock determines CAN baud rate; CAN timing is configured through the controller and transceiver interface. When moving between the 15 MHz and 16 MHz AT90CAN64 ordering codes, recompile the firmware and review timer, baud-rate, watchdog, and startup behavior. Also verify suffix-specific temperature grade, qualification status, and package code in the ordering table rather than relying only on the shared 64-pin TQFP footprint.
معلومات الامتثال
The component description identifies AT90CAN64-15AT1 as an automotive AEC-Q100 part. Other environmental and material-compliance declarations require confirmation from the manufacturer product page or current declaration documents.