ATSAME70J20B-AN - 300MHz Cortex-M7 MCU, 1MB Flash | Microchip
MPN: ATSAME70J20B-AN ✓ نشطATSAME70J20B-AN نظرة عامة
A microcontroller (MCU) is a self-contained computer on a single chip that combines a processor core, non-volatile program memory, volatile data memory, and a set of peripherals such as timers, serial interfaces, and analog converters. MCUs sit at the heart of embedded systems, forming the boundary between the physical world (sensors, actuators, motors) and digital processing. Within the product hierarchy, the ATSAME70J20B-AN is a 32-bit ARM Cortex-M7 MCU in the SAM E70 family, which belongs to the broader class of 32-bit microcontrollers and, above that, to embedded processors and semiconductors.
Key features include 1 MB Flash with 384 KB SRAM, a 12-bit ADC with up to 24 channels, dual CAN-FD controllers, USB 2.0 High-Speed with on-chip transceiver, 10/100 Ethernet MAC, and a wide 1.7 V to 3.6 V supply range. The Cortex-M7 core with double-precision FPU and DSP extensions enables single-cycle MAC operations, making the device suitable for motor control, audio processing, and real-time signal conditioning.
The SAM E70 architecture uses a multi-layer AHB bus matrix with 24 DMA channels, allowing peripherals to move data without CPU intervention. The embedded Flash accelerator and dual 16 KB caches reduce wait states at 300 MHz, sustaining near-zero-wait-state execution for deterministic control loops.
Typical applications include industrial motor drives, building automation gateways, IoT edge nodes with Ethernet/CAN connectivity, audio equipment, and test-and-measurement instruments. The 64-LQFP package with 114 GPIO pins provides ample I/O for multi-peripheral designs.
When designing with this device, ensure the VDDCORE and VDDPLL rails are decoupled with low-ESR ceramic capacitors and that the 12 MHz main crystal is placed close to the XIN/XOUT pins to minimize jitter. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
بدائل مباشرة لـ ATSAME70J20B-AN — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع ATSAME70J20B-AN (نفس عامل الشكل والبصمة) — يختلف في Ethernet, Operating Temperature, CAN, Package, SRAM.
ATSAME70J20B-ANT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ATSAME70J19B-AN
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ATSAME70J19B-ANT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ATSAME70J20A-AN
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ATSAME70J20A-ANT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ATSAME70J21B-AN
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←ATSAME70J20B-AN الحدود القصوى والخصائص الكهربائية
| Core Processor | ARM Cortex-M7 with FPU |
| أقصى تردد للساعة | 300 MHz |
| Program Memory Size | 1 MB (1M x 8) Flash |
| SRAM Size | 384 KB |
| عرض ناقل البيانات | 32-bit |
| Instruction Cache | 16 KB |
| Data Cache | 16 KB |
| ADC Resolution | 12-bit |
| ADC Channels | Up to 24 |
| Supply Voltage Range | 1.7 V to 3.6 V |
| درجة حرارة التشغيل | -40 C to +105 C |
| العلبة / الحالة | 64-LQFP (10x10 mm) |
| Number of I/O | 114 |
| Connectivity | CAN-FD, Ethernet, USB 2.0 HS, SPI, I2C, USART |
| DMA Channels | 24 |
| نوع التركيب | Surface Mount |
| حالة RoHS | Compliant |
| REACH Status | Compliant |
تكوين أطراف ATSAME70J20B-AN
| دبوس 1 | VDDIN — Voltage regulator input supply |
| دبوس 2 | VDDOUT — Voltage regulator output (core supply) |
| دبوس 3 | VDDCORE — Core supply voltage |
| دبوس 4 | VDDPLL — PLL supply voltage |
| دبوس 5 | GNDPLL — PLL ground |
| دبوس 6 | XIN — Main crystal oscillator input |
| دبوس 7 | XOUT — Main crystal oscillator output |
| دبوس 8 | NRST — Reset input (active low) |
| دبوس 9 | TST — Test pin (factory use) |
| دبوس 10 | PA0 — GPIO / ADC channel 0 |
| دبوس 11 | PA1 — GPIO / ADC channel 1 |
| دبوس 12 | PA2 — GPIO / ADC channel 2 |
| دبوس 13 | PA3 — GPIO / ADC channel 3 |
| دبوس 14 | PA4 — GPIO / ADC channel 4 |
| دبوس 15 | PA5 — GPIO / ADC channel 5 |
| دبوس 16 | PA6 — GPIO / ADC channel 6 |
| دبوس 17 | PA7 — GPIO / ADC channel 7 |
| دبوس 18 | PA8 — GPIO / USART0 TX |
| دبوس 19 | PA9 — GPIO / USART0 RX |
| دبوس 20 | PA10 — GPIO / USART1 TX |
| دبوس 21 | PA11 — GPIO / USART1 RX |
| دبوس 22 | PA12 — GPIO / SPI0 MOSI |
| دبوس 23 | PA13 — GPIO / SPI0 MISO |
| دبوس 24 | PA14 — GPIO / SPI0 SPCK |
| دبوس 25 | PA15 — GPIO / SPI0 NPCS0 |
| دبوس 26 | PA16 — GPIO / TWI0 SDA |
| دبوس 27 | PA17 — GPIO / TWI0 SCL |
| دبوس 28 | PA18 — GPIO / CAN0 TX |
| دبوس 29 | PA19 — GPIO / CAN0 RX |
| دبوس 30 | PA20 — GPIO / USB D- |
| دبوس 31 | PA21 — GPIO / USB D+ |
| دبوس 32 | PA22 — GPIO / USB ID |
| دبوس 33 | PA23 — GPIO / USB VBUS |
| دبوس 34 | PA24 — GPIO / PWM channel 0 |
| دبوس 35 | PA25 — GPIO / PWM channel 1 |
| دبوس 36 | PA26 — GPIO / PWM channel 2 |
| دبوس 37 | PA27 — GPIO / PWM channel 3 |
| دبوس 38 | PA28 — GPIO / Ethernet MDC |
| دبوس 39 | PA29 — GPIO / Ethernet MDIO |
| دبوس 40 | PA30 — GPIO / Ethernet TXD0 |
| دبوس 41 | PA31 — GPIO / Ethernet TXD1 |
| دبوس 42 | PB0 — GPIO / Ethernet RXD0 |
| دبوس 43 | PB1 — GPIO / Ethernet RXD1 |
| دبوس 44 | PB2 — GPIO / Ethernet TXEN |
| دبوس 45 | PB3 — GPIO / Ethernet CRS |
| دبوس 46 | PB4 — GPIO / Ethernet RXER |
| دبوس 47 | PB5 — GPIO / Ethernet REFCLK |
| دبوس 48 | PB6 — GPIO / TWI1 SDA |
| دبوس 49 | PB7 — GPIO / TWI1 SCL |
| دبوس 50 | PB8 — GPIO / CAN1 TX |
| دبوس 51 | PB9 — GPIO / CAN1 RX |
| دبوس 52 | PB10 — GPIO / USART2 TX |
| دبوس 53 | PB11 — GPIO / USART2 RX |
| دبوس 54 | PB12 — GPIO / SPI1 MOSI |
| دبوس 55 | PB13 — GPIO / SPI1 MISO |
| دبوس 56 | PB14 — GPIO / SPI1 SPCK |
| دبوس 57 | PB15 — GPIO / SPI1 NPCS0 |
| دبوس 58 | PB16 — GPIO / I2S0 TX |
| دبوس 59 | PB17 — GPIO / I2S0 RX |
| دبوس 60 | PB18 — GPIO / I2S0 SCK |
| دبوس 61 | PB19 — GPIO / I2S0 WS |
| دبوس 62 | PB20 — GPIO / ADC channel 8 |
| دبوس 63 | PB21 — GPIO / ADC channel 9 |
| دبوس 64 | GND — Ground |
التطبيقات النموذجية
ATSAME70J20B-AN مناسب لـ 6 التطبيقs: Industrial Motor Control, IoT Edge Gateway with Ethernet and CAN, Audio Processing and Effects, Test and Measurement Instrumentation, Building Automation and HVAC Controllers, Portable Medical Monitoring Devices.
Industrial Motor Control
The ATSAME70J20B-AN fits industrial motor control because its 300 MHz Cortex-M7 core with double-precision FPU executes field-oriented control (FOC) loops in well under 10 microseconds, while the 12-bit ADC samples phase currents at up to 2 Msps. The dual CAN-FD controllers and 24-channel DMA allow encoder and bus traffic to be handled without CPU intervention, keeping the control loop deterministic. In a typical three-phase inverter, the MCU runs the Park/Clarke transforms and space-vector PWM while the ADC triggers synchronously from the PWM timer. The trade-off is that the 64-LQFP package offers 114 GPIO but no integrated gate driver, so external isolated drivers are still required for the power stage.
موصى به
IoT Edge Gateway with Ethernet and CAN
The ATSAME70J20B-AN suits IoT edge gateways because it integrates a 10/100 Ethernet MAC, dual CAN-FD controllers, and USB 2.0 High-Speed with on-chip transceiver, eliminating external bridge chips. The 1 MB Flash and 384 KB SRAM accommodate a TCP/IP stack, TLS, and protocol translation firmware simultaneously, while the 300 MHz core handles packet processing at wire speed. In a typical gateway, the MCU bridges CAN sensor nodes to an Ethernet backhaul and buffers messages in SRAM using the 24-channel DMA. The trade-off is that the integrated Ethernet MAC still requires an external PHY and magnetics, adding BOM cost and board area compared with a module-based design.
موصى به
Audio Processing and Effects
The ATSAME70J20B-AN is well suited to audio processing because the Cortex-M7 FPU and DSP extensions execute biquad filters and FFTs in single-precision floating point at 300 MHz, supporting multi-channel equalization and effects in real time. The 384 KB SRAM provides enough buffer space for 48 kHz/24-bit multi-channel delay lines, and the I2S/SSI peripherals interface directly to audio codecs. In a typical design, the MCU runs a 1024-point FFT in roughly 30 microseconds, leaving ample headroom for reverb and dynamics processing. The trade-off is that the 64-LQFP package has no integrated audio codec, so an external DAC/ADC such as the AK4558 is required.
موصى به
Test and Measurement Instrumentation
The ATSAME70J20B-AN fits test and measurement instruments because its 12-bit ADC with up to 24 channels and 2 Msps conversion rate captures fast transients, while the 300 MHz core performs real-time filtering and RMS computation. The 1 MB Flash stores calibration tables and waveform data, and the USB 2.0 High-Speed interface streams measurements to a host PC at up to 480 Mbps. In a typical benchtop instrument, the MCU oversamples the ADC and applies digital averaging to reach 14-bit effective resolution. The trade-off is that the on-chip ADC has limited input range, so external programmable-gain amplifiers are needed for low-level signal capture.
موصى به
Building Automation and HVAC Controllers
The ATSAME70J20B-AN suits building automation controllers because the dual CAN-FD and multiple USART/SPI/I2C interfaces connect to BACnet, Modbus, and sensor buses simultaneously, while the 300 MHz core runs the protocol stack and control logic. The wide 1.7 V to 3.6 V supply and -40 C to +105 C operating range support 24 V industrial backplanes with local regulation. In a typical HVAC controller, the MCU polls temperature and pressure sensors over I2C, drives damper actuators via PWM, and reports over Ethernet. The trade-off is that the 64-LQFP package requires careful thermal design when the ambient approaches 105 C.
موصى به
Portable Medical Monitoring Devices
The ATSAME70J20B-AN fits portable medical monitoring because the Cortex-M7 FPU performs ECG filtering and QRS detection in real time, while the 12-bit ADC digitizes biopotential signals at up to 2 Msps. The 384 KB SRAM buffers continuous waveform data, and the USB 2.0 High-Speed interface transfers recordings to a host for analysis. In a typical wearable monitor, the MCU runs a 0.5 Hz to 40 Hz bandpass filter and computes heart rate using a Pan-Tompkins algorithm. The trade-off is that the 64-LQFP package and 300 MHz clock increase power consumption versus a Cortex-M4, so duty-cycled operation is needed for battery life.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ATSAME70J20B-AN — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | ATSAME70J20B-ANT | ATSAME70J19B-AN | ATSAME70J20A-AN | ATSAME70J21B-AN |
|---|---|---|---|---|---|
| Package | 64-LQFP (10x10) | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Processor | ARM Cortex-M7 with FPU | ARM Cortex-M7 with FPU | ARM Cortex-M7 with FPU | ARM Cortex-M7 with FPU | ARM Cortex-M7 with FPU |
| Maximum Clock Frequency | 300 MHz | 300 MHz | 300 MHz | 300 MHz | 300 MHz |
| Flash Memory | 1 MB | 1 MB | 512 KB | 1 MB | 2 MB |
| SRAM | 384 KB | 384 KB | 256 KB | 384 KB | 384 KB |
| Supply Voltage Range | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V |
| Operating Temperature | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C |
| Packaging | Tray | Tape & Reel | Tray | Tray | Tray |
| Silicon Revision | B-revision | B-revision | B-revision | A-revision | B-revision |
أبرز الفروقات
- Full 1 MB Flash and 384 KB SRAM in the 64-LQFP footprint (مقابلATSAME70J19B-AN)
- B-revision silicon with latest errata fixes (مقابلATSAME70J20A-AN)
- Tray packaging for prototyping and low-volume builds (مقابلATSAME70J20B-ANT)
- Headroom for larger firmware without package change (مقابلATSAME70J21B-AN)
ملاحظات التصميم
Decouple VDDCORE, VDDPLL, and VDDIN with 100 nF ceramic capacitors placed within 5 mm of the respective pins, plus a 4.7 uF bulk capacitor on VDDIN. The internal core regulator requires a 2.2 uF low-ESR capacitor on VDDOUT; using a high-ESR capacitor can cause regulator instability and erratic core behavior at 300 MHz.
Place the 12 MHz main crystal and its two load capacitors as close as possible to XIN/XOUT, keeping the traces under 10 mm and guarded by ground. Route the USB D+/D- pair as a 90 ohm differential pair and keep the Ethernet TX/RX pairs matched to within 5 mil to preserve signal integrity at 100 Mbps.
Estimated: at 300 MHz with all peripherals active, the ATSAME70J20B-AN core current is approximately 60-80 mA at 1.2 V, giving roughly 100 mW of core dissipation. With a 64-LQFP theta_JA near 45 C/W, the junction rise is about 5 C above ambient, so no heatsink is required below 85 C ambient; verify with the actual peripheral load.
Do not leave the NRST pin floating; add a 10 kOhm pull-up to VDDIO and a 100 nF capacitor to ground to prevent spurious resets. Also ensure the TST pin is tied low or left per datasheet guidance, as incorrect termination can prevent the device from booting from Flash.
معلومات الامتثال
EU RoHS compliant and REACH compliant per distributor compliance data. DRC conflict-free status reported by Abacus Technologies. Not AEC-Q100 qualified; contact Microchip for automotive-grade SAM variants.
