ATSAME70J19B-ANT - 300MHz Cortex-M7 MCU 512KB Flash LQFP-64
MPN: ATSAME70J19B-ANT ✓ نشطATSAME70J19B-ANT نظرة عامة
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of on-chip peripherals (ADC, timers, communication interfaces). The Cortex-M7 core specifically adds a double-precision FPU, DSP extensions, and an instruction/data cache, placing it at the top of the Cortex-M performance hierarchy (Cortex-M7 > Cortex-M4 > Cortex-M3 > Cortex-M0+). Within Microchip's portfolio, the SAM E70 sits in the high-performance MCU tier, between the lower-cost SAMD5x Cortex-M4 family and the Cortex-M7-based SAME70/SAMS70/SAMV71 series.
Key features include IEEE 754 single/double-precision floating-point arithmetic, 16 KB instruction cache plus 16 KB data cache, Tightly Coupled Memory (TCM) interfaces, embedded Trace Macrocell (ETM) for instruction trace, and a 1 MSPS 12-bit ADC. Peripherals span Ethernet MAC, CAN-FD, USB 2.0 High-Speed with on-chip PHY, three CAN-FD controllers, multiple USART/UART/SPI/TWI interfaces, an external bus interface (EBI) for SRAM/SDRAM expansion, and a camera interface. An integrated cryptographic accelerator and True Random Number Generator (TRNG) support secure boot and TLS applications.
The SAM E70 architecture uses a 6-layer AHB/AXI bus matrix to keep CPU, DMA, Ethernet, and display streams concurrent without bus starvation. The 300 MHz Cortex-M7 delivers 1500 CoreMark / 600 DMIPS, roughly 2x the performance of a Cortex-M4 at the same frequency. Hardware DSP and SIMD instructions accelerate audio codecs and motor-control loops, while the FPU removes the need for software floating-point emulation in PLC and instrumentation code.
Typical applications include industrial Ethernet slaves (EtherCAT, PROFINET, EtherNet/IP), building-automation controllers, audio processing and USB audio interfaces, automotive body and infotainment modules, IoT gateways with TLS offload, motor-control FOC inverters, and graphical HMI with TFT LCD. The wide 1.62V-3.6V I/O supply with internal LDO simplifies mixed-voltage designs.
When designing with this device, allocate a 4-layer PCB with the EBI bus carefully length-matched if SDRAM is used, and ensure the 12 MHz crystal load capacitance matches the crystal datasheet (typically 12-20 pF). Use the ASF4 / MPLAB Harmony 3 framework for peripheral drivers; bare-metal register-level coding is feasible but reduces portability across the SAM E70/S70/V70/V71 family. The crypto accelerator requires a firmware library; verify license terms if distributing binary firmware.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet, giving engineers a single reference for sourcing and second-source planning.
بدائل مباشرة لـ ATSAME70J19B-ANT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع ATSAME70J19B-ANT (نفس عامل الشكل والبصمة) — يختلف في Operating Temperature, SRAM, Package, Ethernet, Mounting Type.
ATSAME70J19B-AN
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ATSAME70J19A-ANT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ATSAME70N19B-ANT
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ATSAME70J20B-ANT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ATSAMS70J19B-ANT
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ATSAME70J19B-ANT الحدود القصوى والخصائص الكهربائية
| Core Architecture | ARM Cortex-M7 with FPU |
| Core Speed (Max) | 300 MHz |
| Program Memory (Flash) | 512 KB |
| SRAM | Up to 256 KB multi-port SRAM |
| Cache | 16 KB I-cache + 16 KB D-cache |
| العلبة | 64-LQFP (10x10 mm) |
| Operating Voltage | 1.62 V to 3.6 V |
| درجة حرارة التشغيل | -40 C to +105 C (industrial) |
| ADC | 12-bit, up to 24 channels |
| Ethernet | 10/100 MAC (MII/RMII) with 1588 support |
| USB | USB 2.0 High-Speed with on-chip PHY |
| CAN | 3x CAN-FD controllers |
| External Bus Interface | EBI for SRAM/SDRAM/NOR |
| Cryptography | AES, TRNG, secure boot accelerator |
| نوع التركيب | Surface Mount |
تكوين أطراف ATSAME70J19B-ANT
| دبوس 1 | PB0 — GPIO PB0 / PWMH0 |
| دبوس 2 | PB1 — GPIO PB1 / PWML0 |
| دبوس 3 | PB2 — GPIO PB2 / PWMH1 |
| دبوس 4 | PB3 — GPIO PB3 / PWML1 |
| دبوس 5 | VDDIO — I/O supply voltage |
| دبوس 6 | VSS — Ground |
| دبوس 7 | VDDCORE — Core voltage (internal LDO output) |
| دبوس 8 | PA0 — GPIO PA0 |
| دبوس 9 | PA1 — GPIO PA1 |
| دبوس 10 | PA2 — GPIO PA2 |
| دبوس 11 | PA3 — GPIO PA3 |
| دبوس 12 | PA4 — GPIO PA4 |
| دبوس 13 | PA5 — GPIO PA5 |
| دبوس 14 | PA6 — GPIO PA6 |
| دبوس 15 | PA7 — GPIO PA7 |
| دبوس 16 | PA8 — GPIO PA8 |
| دبوس 17 | PA9 — GPIO PA9 |
| دبوس 18 | PA10 — GPIO PA10 |
| دبوس 19 | PA11 — GPIO PA11 / USB D- |
| دبوس 20 | PA12 — GPIO PA12 / USB D+ |
| دبوس 21 | PA13 — GPIO PA13 |
| دبوس 22 | PA14 — GPIO PA14 |
| دبوس 23 | VDDIO — I/O supply voltage |
| دبوس 24 | VSS — Ground |
| دبوس 25 | PB4 — GPIO PB4 |
| دبوس 26 | PB5 — GPIO PB5 |
| دبوس 27 | PB6 — GPIO PB6 |
| دبوس 28 | PB7 — GPIO PB7 |
| دبوس 29 | PB8 — GPIO PB8 |
| دبوس 30 | PB9 — GPIO PB9 |
| دبوس 31 | PB10 — GPIO PB10 |
| دبوس 32 | PB11 — GPIO PB11 |
| دبوس 33 | PB12 — GPIO PB12 |
| دبوس 34 | PB13 — GPIO PB13 |
| دبوس 35 | PB14 — GPIO PB14 |
| دبوس 36 | PB15 — GPIO PB15 |
| دبوس 37 | PC0 — GPIO PC0 |
| دبوس 38 | PC1 — GPIO PC1 |
| دبوس 39 | PC2 — GPIO PC2 |
| دبوس 40 | PC3 — GPIO PC3 |
| دبوس 41 | PC4 — GPIO PC4 |
| دبوس 42 | PC5 — GPIO PC5 |
| دبوس 43 | PC6 — GPIO PC6 |
| دبوس 44 | PC7 — GPIO PC7 |
| دبوس 45 | PC8 — GPIO PC8 |
| دبوس 46 | PC9 — GPIO PC9 |
| دبوس 47 | PC10 — GPIO PC10 |
| دبوس 48 | PC11 — GPIO PC11 |
| دبوس 49 | PC12 — GPIO PC12 |
| دبوس 50 | PC13 — GPIO PC13 |
| دبوس 51 | PC14 — GPIO PC14 |
| دبوس 52 | PC15 — GPIO PC15 |
| دبوس 53 | PD0 — GPIO PD0 |
| دبوس 54 | PD1 — GPIO PD1 |
| دبوس 55 | PD2 — GPIO PD2 |
| دبوس 56 | PD3 — GPIO PD3 |
| دبوس 57 | PD4 — GPIO PD4 |
| دبوس 58 | PD5 — GPIO PD5 |
| دبوس 59 | PD6 — GPIO PD6 |
| دبوس 60 | PD7 — GPIO PD7 |
| دبوس 61 | PD8 — GPIO PD8 |
| دبوس 62 | PD9 — GPIO PD9 |
| دبوس 63 | NRST — Reset input, active low |
| دبوس 64 | VDDIO — I/O supply voltage |
التطبيقات النموذجية
ATSAME70J19B-ANT مناسب لـ 6 التطبيقs: Industrial Ethernet Slave (EtherCAT / PROFINET / EtherNet/IP), USB Audio Interface / Hi-Fi DAC, IoT Gateway with TLS Offload, Automotive Body Control / Gateway Module, Motor Control / FOC Inverter, Graphical HMI with TFT LCD.
Industrial Ethernet Slave (EtherCAT / PROFINET / EtherNet/IP)
The ATSAME70J19B-ANT is a strong fit for industrial Ethernet slave controllers because of its on-chip 10/100 Ethernet MAC with IEEE 1588 hardware timestamping and 300 MHz Cortex-M7 core. Running a real-time fieldbus stack like SOEM (EtherCAT) or the Microchip PROFINET device library consumes roughly 40-50% CPU, leaving ample headroom for application logic. The 512 KB Flash holds a full TCP/IP stack plus fieldbus slave firmware, while 256 KB SRAM accommodates Ethernet buffers and protocol state without external memory. The wide 1.62-3.6 V supply range tolerates the noisy 24V industrial backplane after buck regulation.
موصى به
USB Audio Interface / Hi-Fi DAC
For USB audio DAC and ADC interfaces, the ATSAME70J19B-ANT's USB 2.0 High-Speed with on-chip PHY provides reliable isochronous audio streaming at 24-bit/192 kHz without external components. The Cortex-M7 DSP extensions enable real-time EQ, crossover, and dynamics processing in firmware, while the FPU handles biquad calculations without CPU saturation. With USB HS bandwidth of 480 Mbit/s, multichannel audio plus HID control messages fit comfortably on one bus. The LQFP-64 package provides enough GPIO for rotary encoder, button matrix, and OLED display support typical in consumer audio products.
موصى به
IoT Gateway with TLS Offload
The ATSAME70J19B-ANT is well-suited for industrial IoT gateways running MQTT, CoAP, or HTTP/TLS to cloud brokers. Its hardware AES and TRNG accelerator reduce TLS 1.2/1.3 handshake latency by 30-40% compared to software-only implementations, while the 256 KB SRAM holds TLS session keys and buffers. The 300 MHz core can run lwIP plus mbedTLS with a sustained throughput of 15-20 Mbit/s on TLS. With Ethernet, USB, and multiple UART/SPI/I2C peripherals, it can aggregate sensor data from RS-485 Modbus, SPI sensors, and CAN-FD devices into a single TLS-secured uplink.
موصى به
Automotive Body Control / Gateway Module
In automotive body controllers and central gateway modules, the ATSAME70J19B-ANT's three CAN-FD controllers aggregate multiple vehicle buses while the Ethernet MAC bridges to the in-vehicle backbone. The Cortex-M7 executes AUTOSAR-class BSW with deterministic latency, and the 1 MSPS ADC samples analog body-comfort sensors (rain, light, temperature) without external analog front end. Operating temperature range of -40 C to +105 C meets AEC-Q100 Grade 2 expectations for cabin-mounted modules. Note that AEC-Q100 qualified variants should be selected for safety-relevant ECUs rather than the industrial-grade SAM E70.
موصى به
Motor Control / FOC Inverter
Field-oriented control (FOC) of three-phase PMSM and BLDC motors runs efficiently on the ATSAME70J19B-ANT at update rates up to 30 kHz with full PID and Park/Clarke transforms in hardware FPU. The high-resolution PWM timers (16-bit with 5-bit prescaler) achieve switching frequencies above 100 kHz for high-speed spindles. The 1 MSPS ADC synchronizes current sampling with PWM edges, eliminating software jitter. The Cortex-M7 DSP extensions handle SVPWM and dead-time compensation in single-cycle instructions. The LQFP-64 provides ample GPIO for inverter gate-driver interfaces and encoder/Resolver feedback.
موصى به
Graphical HMI with TFT LCD
The ATSAME70J19B-ANT can drive small TFT LCD displays (up to 480x272) via the integrated external bus interface (EBI) with 8080/6800 parallel interface plus DMA2D-like peripheral for line-by-line transfers. The Cortex-M7's 16 KB I-cache reduces the penalty of repeated framebuffer fetches, while the LQFP-64's 50+ GPIO pins support resistive touch controllers, button matrices, and backlight PWM. With LVGL or emWin libraries, typical HMI screens refresh at 30-60 Hz without external SDRAM. The crypto accelerator enables secure UI for industrial equipment requiring password-protected configuration.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ATSAME70J19B-ANT — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | ATSAME70J19B-AN | ATSAME70J19A-ANT | ATSAME70N19B-ANT | ATSAME70J20B-ANT | ATSAMS70J19B-ANT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | LQFP-64 (10x10 mm) | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same |
| Core | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz |
| Flash | 512 KB | 512 KB | 512 KB | 256 KB | 1024 KB | 512 KB |
| SRAM | 256 KB | 256 KB | 256 KB | 128 KB | 384 KB | 256 KB |
| Ethernet MAC | Yes (10/100 with 1588) | Yes | Yes | Yes | Yes | No |
| USB HS PHY | Yes | Yes | Yes | Yes | Yes | Yes |
| Silicon Revision | B | B | A | B | B | B |
أبرز الفروقات
- Highest Flash density in SAM E70 LQFP-64 family at 512 KB (مقابلATSAME70N19B-ANT)
- Silicon revision B includes all known errata fixes (مقابلATSAME70J19A-ANT)
- Includes Ethernet MAC with IEEE 1588 hardware timestamping (مقابلATSAMS70J19B-ANT)
ملاحظات التصميم
The 64-LQFP at 0.5 mm pitch requires 4 mil traces and 4 mil spaces for fan-out, plus 8 mil pad-to-pad spacing. Use a 4-layer PCB with continuous ground plane under the device and a 0.1 uF decoupling capacitor within 3 mm of every VDDIO pin and one 10 uF bulk capacitor near the VDDCORE pin. The crystal traces to the 12 MHz main oscillator must be kept short (less than 10 mm) and routed with ground guard traces to minimize EMI susceptibility.
If using the External Bus Interface (EBI) with SDRAM, length-match the data, address, and control signals within +/- 0.5 mm and place a 22 ohm series damping resistor at the MCU output. Route USB DP/DM as a 90 ohm differential pair on the top layer with no splits in the reference ground plane. Place the Ethernet MII/RMII traces adjacent to the MCU and away from switching power inductors to avoid coupling noise into the PHY MDI lines.
Do not enable the brown-out detector at 1.62 V if your application uses a 1.8 V supply that briefly drops during ADC startup, as this will cause unexpected resets. Ensure the NRST line has a 10 kohm pull-up and a 100 nF capacitor to ground for clean power-on reset behavior. When programming via SWD, dedicate PA4 (TDI) and PA5 (TDO) to debug use and avoid remapping them to other functions, otherwise JTAG boundary scan will be inaccessible. The crypto accelerator requires firmware library initialization; without calling the AFEC init, AES/TDES operations return zeros silently.
Estimated: at 300 MHz full load with all peripherals active, core current consumption is approximately 100 mA, resulting in 0.36 W dissipation at 3.3 V. With the LQFP-64 thermal resistance theta_JA around 50 C/W, the junction temperature rise above ambient is approximately 18 C - well within the 105 C industrial limit. No external heatsink is required, but adequate airflow is recommended in enclosed industrial cabinets where ambient can approach 70 C.
معلومات الامتثال
Industrial temperature grade -40C to +105C. RoHS and REACH compliant per Microchip product declaration. Not AEC-Q100 qualified - for automotive safety-relevant applications, choose a SAM E70 variant with explicit automotive qualification or use SAM RH850/S32K3 from NXP/Renesas.
