BCM5488SA7IPB - Octal Gigabit Ethernet Transceiver | Broadcom
MPN: BCM5488SA7IPB ✓ نشطBCM5488SA7IPB نظرة عامة
An Ethernet transceiver is an interface integrated circuit that converts between digital data and electrical signaling on twisted-pair Ethernet cables. Within the network interface hierarchy, a transceiver sits between a MAC or switching ASIC and the physical network, handling the physical-layer functions needed for 10BASE-T, 100BASE-TX, and 1000BASE-T links. The BCM5488SA7IPB therefore belongs to the broader Ethernet PHY, interface IC, networking semiconductor, and semiconductor categories rather than functioning as a general-purpose processor.
The principal cataloged feature is support for full- and half-duplex 10/100/1000BASE operation across an eight-channel arrangement. A multiport device can simplify board routing and reduce the number of separate PHY packages compared with discrete single-port implementations. Distributor records also associate the component with Gigabit Ethernet transceiver functions, making it relevant to switches, routers, network appliances, industrial Ethernet equipment, and multiport Ethernet line cards. Exact interface voltage, media reach, cable-length, power, and environmental limits are not stated in the available catalog excerpts.
The BCM5488SA7IPB uses an integrated-circuit architecture intended to bridge a network-switching or packet-processing ASIC with copper Ethernet physical layers. Its 484-pin PBGA provides a large, high-pin-count surface-mount footprint suitable for complex, high-speed mixed-signal circuitry. Such packages demand careful power-plane distribution, ground-return design, decoupling, and via-in-pad or fanout strategies so that high-speed differential pairs and sensitive transceiver references maintain controlled impedance and return paths.
Typical deployment points include eight-port Gigabit Ethernet switches, router interfaces, network interface controllers, industrial control cabinets, and communications equipment with multiple 10/100/1000BASE ports. In these systems, the transceiver simplifies physical-layer implementation while the host ASIC handles packet processing, port arbitration, and higher-level protocol functions. Multicomponent boards should confirm cable-media support, autonegotiation behavior, register compatibility, and thermal performance before production release.
The primary design consideration is that a high-pin-count PBGA must be treated as a complete RF-controlled and thermally managed layout, not as a generic digital component. Place the device according to its recommended footprint, preserve continuous supply and ground planes, decouple each supply domain at its pins, and route each Ethernet differential pair as a controlled-impedance pair. Verify magnetics or coupling components, line-side protection, isolation spacing, and return-path continuity against the applicable reference design.
This product record combines cataloged device identity, packaging, sourcing information, technical context, application guidance, and a compatibility-focused comparison. Engineers should use it to identify whether the BCM5488SA7IPB belongs in the architecture, then confirm every unreleased electrical limit, pin function, register, and lifecycle decision against the current Broadcom technical documentation before schematic release or production procurement.
بدائل مباشرة لـ BCM5488SA7IPB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
BCM5461SA1IPFG
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
BCM54220SB0IFBG
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
BCM5488SA7IPB الحدود القصوى والخصائص الكهربائية
| Product Type | Ethernet transceiver |
| Ethernet Support | 10/100/1000BASE |
| Cataloged Channel Arrangement | 8 channels |
| Duplex Support | Full and half duplex |
| Maximum Data Rate | 1000 Mbps |
| العلبة | 484-pin PBGA |
| نوع التركيب | Surface mount |
| Ethernet Application | Copper Ethernet physical-layer interface |
دليل تكوين أطراف BCM5488SA7IPB 484-pin pbga
تكوين الأطراف لـ BCM5488SA7IPB (حزمة 484-pin pbga). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ BCM5488SA7IPB.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
BCM5488SA7IPB مناسب لـ 6 التطبيقs: Eight-Port Gigabit Ethernet Switch, Industrial Network Gateway, Router Network Interface, Telecommunications Access Equipment, Industrial Control Cabinet, Network Appliance Interface Card.
Eight-Port Gigabit Ethernet Switch
The BCM5488SA7IPB fits an eight-port switch line card because its cataloged configuration provides eight full- or half-duplex 10/100/1000BASE channels in one 484-pin PBGA. Consolidating the physical-layer functions can simplify the relationship between copper ports and a host switching ASIC while reducing the number of transceiver packages. The implementation still requires verification of each port's media support, auto-negotiation behavior, line-side circuitry, and common-mode compatibility. PCB planning should provide continuous supply and ground planes, short decoupling paths, and controlled-impedance differential routing for every Ethernet channel.
موصى به
Industrial Network Gateway
The BCM5488SA7IPB can support a multiport industrial Ethernet gateway where controllers, sensors, and remote equipment require 10/100/1000BASE connectivity. Its eight-channel arrangement allows a gateway to consolidate several copper links while the host processor manages protocols, alarms, and local control functions. Qualification for an industrial environment depends on confirming the operating-temperature range, isolation architecture, ESD protection, and EMC performance for the finished system. The dense PBGA also concentrates heat, so thermal simulation and copper spreading around the device should be completed before enclosure qualification.
موصى به
Router Network Interface
The BCM5488SA7IPB is applicable to router and routing-interface designs that require multiple copper Ethernet ports on one board. Its eight 10/100/1000BASE channels can provide physical-layer connectivity behind a routing or packet-processing ASIC, avoiding a board populated with separate single-port PHY packages. Engineering review must confirm host bus width, clock requirements, register initialization, and whether the selected Broadcom configuration supports all eight ports simultaneously. High-speed traces from the host ASIC to the PBGA should be length-matched and routed over continuous reference planes to minimize data-integrity risk.
موصى به
Telecommunications Access Equipment
The BCM5488SA7IPB can serve in telecommunications access equipment requiring multiple Gigabit Ethernet physical interfaces for service nodes or aggregation hardware. Consolidating eight channels on one high-pin-count PBGA supports compact line-card designs where space and component count are important. Deployment suitability must be validated against the controlled Broadcom specifications for temperature, power, EMC, and cable reach, as these values are not established by the catalog excerpts. The layout should also accommodate telecom magnetics or coupling components, surge protection, and the isolation spacing required by the target product category.
موصى به
Industrial Control Cabinet
The BCM5488SA7IPB is suitable for consideration in industrial control cabinets that connect programmable controllers, vision equipment, remote I/O, and service laptops over copper Ethernet. The eight-channel architecture allows several links to share a compact physical-layer subsystem while supporting links at 10, 100, or 1000 Mbps. A production design should confirm port-level media features and environmental limits rather than assuming that every channel has identical configuration. Robust line-side protection, isolated magnetics, grounded chassis interfaces, and a power budget that accounts for eight simultaneous links are essential implementation requirements.
موصى به
Network Appliance Interface Card
The BCM5488SA7IPB can serve in a network appliance interface card where several Gigabit Ethernet ports are exposed to users, storage systems, or upstream equipment. Its cataloged eight-channel 10/100/1000BASE capability supports a consolidated physical layer, while a host ASIC or processor performs packet processing. The design team must confirm boot behavior, management-register access, firmware support, and thermal dissipation for the populated board. Because a 484-pin PBGA limits routing options, use the recommended via pattern and land geometry, and inspect assembled X-ray results to identify voiding or via defects that could compromise thermal and electrical performance.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ BCM5488SA7IPB — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | BCM5461SA1IPFG | BCM54220SB0IFBG |
|---|---|---|---|
| Brand | Broadcom | Broadcom | Broadcom |
| Package | 484-pin PBGA | 484-pin PBGA | 484-pin PBGA |
| Ethernet Support | 10/100/1000BASE | 10/100/1000BASE Ethernet family | Gigabit Ethernet family |
| Mounting Type | Surface mount | Surface mount | Surface mount |
أبرز الفروقات
- Eight-channel physical-layer integration (مقابلBCM5461SA1IPFG)
- Full- and half-duplex multiport support (مقابلBCM5461SA1IPFG)
- Documented 484-pin PBGA footprint (مقابلBCM54220SB0IFBG)
ملاحظات التصميم
Treat the 484-pin PBGA as a high-speed mixed-signal layout. Use the controlled Broadcom land pattern, place local decoupling at the relevant supply pins, maintain uninterrupted reference planes beneath the device, and route Ethernet differential pairs as short, continuously referenced traces. Verify via construction against the package and assembly requirements rather than relying on a generic BGA via-in-pad rule.
Eight simultaneous 1 Gbps channels can concentrate heat around the PBGA. Calculate dissipation from the confirmed supply voltage and total current for the populated board, model the package and board construction, and provide copper spreading, airflow, or a thermal interface appropriate to the enclosure. Validate the hottest expected operating condition, because an eight-port configuration can be materially hotter than a single-port test configuration.
Preserve return paths and impedance continuity from the transceiver pins to the line-side network interface. Keep the digital host interface and sensitive analog or clock references away from copper and magnetics where practical, use short ground-via fences at interface boundaries, and apply the controlled reference design's via and breakout geometry. After fabrication, verify impedance coupons and inspect BGA assembly for voids that could alter thermal behavior.
Do not treat another Broadcom Gigabit Ethernet transceiver as interchangeable merely because it uses a PBGA. Before replacing the BCM5488SA7IPB, compare every BGA assignment, power domain, ground reference, clock input, management interface, reset connection, and media-side signal. Also confirm register initialization and supported operating modes; a footprint match alone does not establish functional or production compatibility.
معلومات الامتثال
The available catalog records do not provide authoritative environmental or qualification declarations for the exact device.