DG401AK - Dual High-Speed SPST Analog Switch | Vishay
MPN: DG401AK ✓ نشطDG401AK نظرة عامة
An analog switch is a semiconductor device that uses digital control signals to connect or disconnect analog signal paths. The DG401AK belongs to the analog switch and switch-matrix hierarchy, where the SPST configuration provides one selectable path per circuit. Its CMOS implementation supports low-power operation and high-speed switching, making the device suitable for test equipment, signal routing, instrumentation, and communication systems.
The principal features are two switch circuits, normally open SPST behavior, a 1:1 routing configuration, and a specified 35 ohm on-resistance. These characteristics allow it to serve as a building block in larger switch matrices and signal-selection networks. The CERDIP package provides a through-hole mechanical format and is intended for applications where leaded components and conventional PCB assembly methods are preferred.
The DG401AK uses independent control and common-source switching structures within a dual analog-switch package. Because each channel is normally open, the default state presents a high-impedance path until the corresponding control input activates its channel. The low-power CMOS architecture is particularly useful when system power consumption, switching speed, and signal-path isolation must be balanced in the same compact package.
Typical uses include multimeter and oscillometer signal selection, automated test equipment, data-acquisition front ends, sample-and-hold systems, analog signal routing, and communication or instrumentation interfaces. In each application, the DG401AK can isolate unused signal branches or connect a source to a downstream measurement channel while the control logic determines the active path.
Designers should pay close attention to the 35 ohm on-resistance and the complete timing, voltage, and logic-level specifications in the manufacturer datasheet. Place the device so that sensitive analog traces remain short, provide adequate return paths, and account for off-state leakage, control timing, and switch capacitance when establishing signal-integrity limits.
This product page consolidates package identification, verified distributor specifications, practical application guidance, and pin-compatible sourcing options. It is intended to help engineers compare the DG401AK with military-qualified and manufacturer-labeled versions while keeping the required 16-pin CERDIP footprint and electrical architecture in view.
بدائل مباشرة لـ DG401AK — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
DG401AK/883
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DG401AK/883B
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DG401AK
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DG401AK
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DG401AK
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DG401AK الحدود القصوى والخصائص الكهربائية
| Number of Circuits | 2 circuits |
| Switch Configuration | 1:1 |
| Number of Switches | 2 independently controlled SPST switches |
| On-Resistance | 35 ohm |
| العلبة | 16-pin CERDIP |
| Number of Terminals | 16 terminals |
| نوع التركيب | Through-hole DIP |
| Surface-Mount Capability | No |
| Switch State | Normally open |
| Technology | CMOS analog switch |
| Switching Class | Low-power, high-speed |
| AEC-Q100 Qualification | Not applicable |
دليل تكوين أطراف DG401AK 16-pin cerdip
تكوين الأطراف لـ DG401AK (حزمة 16-pin cerdip). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DG401AK.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
DG401AK مناسب لـ 6 التطبيقs: Automated Test Equipment Signal Routing, Data-Acquisition Front End, Analog Multiplexer Signal Selection, Instrumentation Signal Isolation, Sample-and-Hold Signal Control, Communication Interface Switching.
Automated Test Equipment Signal Routing
The DG401AK fits automated test equipment because two independent 1:1 SPST channels can select or isolate analog paths under separate control signals. Its 35 ohm on-resistance adds a defined series impedance that should be included in the measurement path, while low-power, high-speed CMOS switching supports short acquisition-cycle decisions. Place each switch near the routed source or instrument input, use a solid ground reference, and allow the control signal to settle before sampling. The 16-pin CERDIP package is suitable for leaded test-fixture and backplane assemblies where through-hole robustness is preferred over board area.
موصى به
Data-Acquisition Front End
The DG401AK can route or isolate two analog inputs in a data-acquisition front end when the system requires compact, independently controlled SPST paths. Its 1:1 configuration preserves the selected signal topology, and the 35 ohm on-resistance must be compared with the source and ADC input impedances to determine whether loading is acceptable. The dual normally open arrangement allows unused channels to remain isolated while a measurement is active. For sensitive high-impedance sources, minimize trace length, provide clean grounding, and account for switch capacitance and leakage in the acquisition error budget.
موصى به
Analog Multiplexer Signal Selection
The DG401AK can serve as a building block in an analog multiplexer or switch matrix because each package supplies two normally open, independently controlled SPST paths. A 1:1 signal configuration supports straightforward selection networks, although multiple packages may be required to build larger matrices. The 35 ohm path resistance should be evaluated against signal amplitude, source impedance, and downstream accuracy requirements. For high-frequency routing, use short controlled-impedance traces and minimize parasitic capacitance, while ensuring that the control-driver timing and supply levels satisfy the device requirements.
موصى به
Instrumentation Signal Isolation
The DG401AK is useful in instrumentation designs that need to isolate one of two measurement paths. Its normally open behavior leaves a channel disconnected until its control input is asserted, reducing unwanted interaction between source and instrument when the path is inactive. With a specified on-resistance of 35 ohm, it is better suited to moderate-impedance systems than to precision divider networks where resistance variation would directly impair accuracy. Confirm off-isolation and leakage limits in the manufacturer datasheet, and keep the analog traces short and symmetric for predictable behavior.
موصى به
Sample-and-Hold Signal Control
The DG401AK can control the connection of two candidate signals in a sample-and-hold or switched-measurement circuit. The low-power, high-speed CMOS switch supports rapid path selection, while the dual SPST organization allows independent control of related channels. Designers should verify the switch transition time, control-logic levels, and charge injection against the settling requirements of the downstream amplifier or converter. A solid ground plane, short analog connections, and deliberate return paths help prevent control-edge coupling from appearing as an error on the held signal.
موصى به
Communication Interface Switching
The DG401AK can select between low-frequency communication or control signals when the design requires two isolated 1:1 routes in a single through-hole package. The dual normally open structure supports disconnecting inactive branches and limiting signal contention when control logic has established the intended route. The 35 ohm on-resistance should be checked against line-driver and receiver impedances, and the complete bandwidth, supply, logic-threshold, and off-isolation limits should be confirmed before deployment. Short branch routing and a continuous ground reference are important when minimizing crosstalk and ground-potential effects.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ DG401AK — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DG401AK/883 | DG401AK/883B | DG401AK |
|---|---|---|---|---|
| Package | 16-pin CERDIP | 16-pin CERDIP | 16-pin CERDIP | 16-pin CERDIP |
| Brand | Vishay Intertechnology | Vishay Intertechnology | Analog Devices | Analog Devices, Maxim Integrated, and TEMIC Semiconductors |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Switch Configuration | 1:1 | 1:1 | SPST, 1:1 | 1:1 |
| Switch State | Normally open | Normally open | Normally open | Normally open |
| Technology | CMOS analog switch | CMOS analog switch | CMOS analog switch | CMOS analog switch |
| Switching Class | Low-power, high-speed | Low-power, high-speed | High-speed | Low-power, high-speed |
| Mounting Type | Through-hole DIP | Through-hole DIP | Through-hole DIP | Through-hole DIP |
أبرز الفروقات
- Lower listed on-resistance than the DG401AK/883 ordering code (مقابلDG401AK/883)
- Both channels are integrated in one dual SPST package (مقابلA single-channel analog switch)
- Through-hole ceramic-DIP construction supports leaded assembly (مقابلSurface-mount analog switches)
ملاحظات التصميم
Treat the 35 ohm on-resistance as part of the complete signal-path impedance. For high-impedance sensors or precision dividers, verify that switch resistance, leakage, and variation do not exceed the measurement error budget. Keep the switched node compact, maintain a continuous ground reference, and place any required input or output capacitance close to the associated device pins.
The DG401AK uses a 16-pin CERDIP footprint, so preserve the manufacturer package drawing for lead spacing, hole diameter, and pin numbering. Orient the device consistently with the PCB footprint, avoid excessive force during insertion, and inspect solder fillets after through-hole reflow. Do not assign signal connections solely from the generic DIP outline; verify every terminal against the DG401 pin-description table.
Confirm control-logic thresholds, supply voltage, switching time, and allowable control timing before using the device with a new microcontroller or test controller. Because each channel is normally open, an asserted control state must correspond to the intended connection. Also verify the manufacturer label and suffix when replacing DG401AK with /883 or /883B ordering codes, since mechanical similarity does not establish identical qualification terms.
معلومات الامتثال
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not identified in the product records used for this page. AEC-Q100 is not applicable because DG401AK is an analog interface switch rather than an automotive-qualified component.