Analog Devices

DG418LDJ+ - 35 Ohm SPST Analog Switch | Analog Devices

MPN: DG418LDJ+ ✓ نشط
±4.5 V Vdss 35 ohm maximum Rds(on) 8-pin PDIP Package
الحد الأدنى للطلب: 1 |

DG418LDJ+ نظرة عامة

The Analog Devices DG418LDJ+ is a single-channel, normally open SPST CMOS analog switch with 35 ohm on resistance, 3 V logic compatibility, and an 8-pin PDIP package. It supports dual supply voltages from ±4.5 V to ±20 V and is intended for precision signal-routing applications requiring low control logic compatibility and fast switching performance.

An analog switch is a semiconductor device that connects or isolates circuit nodes under digital control. The DG418LDJ+ belongs to the analog switch and multiplexer hierarchy, where it provides one independently controlled SPST path. Unlike a mechanical relay, the CMOS implementation switches without moving contacts, making it suitable for test systems, instrumentation, data acquisition, communications, and industrial control equipment where repetitive operation, compact size, and controlled switching behavior are important.

The device provides a 1:1, one-circuit configuration with a maximum on resistance of 35 ohm. Its normally open SPST topology keeps the switched path disconnected until the control input activates it. A 3 V logic-compatible control interface allows the switch to be operated by modern low-voltage digital logic, while the ±4.5 V to ±20 V analog supply range supports both dual-rail and bipolar signal environments. The listed maximum switching turn-off time is 185 ns.

Internally, the DG418LDJ+ uses CMOS circuitry to control the analog conduction path while separating the control input from the switched terminals. This architecture supports fast operation and low off-state leakage, although the exact leakage, bandwidth, charge injection, and channel capacitance values must be confirmed in the manufacturer datasheet before final signal-integrity calculations. The 8-pin PDIP package also provides generous lead spacing for breadboard, through-hole prototype, and manually assembled industrial applications.

Typical uses include precision test-and-measurement systems, sensor signal switching, sample-and-hold subsystems, battery-powered acquisition equipment, and communication interface routing. The normally open behavior is useful when a default isolation state is preferred, while the dual-supply range supports bipolar waveforms commonly encountered in instrumentation and industrial control systems.

PCB layout should keep the analog signal path short and place decoupling capacitors close to the supply pins. Confirm logic thresholds, signal swing, bandwidth, leakage, and switch capacitance against the application before release, especially when switching low-amplitude or high-impedance signals where charge injection and off-state leakage can affect measurement accuracy.

This page consolidates the component configuration, electrical limits, package details, comparison data, and practical replacement guidance for engineers evaluating the DG418LDJ+. It also distinguishes verified drop-in options from broader functional equivalents, helping simplify sourcing and board-level design decisions.

بدائل مباشرة لـ DG418LDJ+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع DG418LDJ+ (نفس عامل الشكل والبصمة) — يختلف في Switch Configuration.

Analog Devices
Switch Configuration: SPST normally open
قارن مع DG418LDJ+ →

DG418LDJ

✅ بديل مباشر
📦 8-pin PDIP
Same listed 1:1, 35 ohm, single-channel SPST configuration; ordering suffix differs by 0% in the stated key parameters

📋 بديل مرجعي (غير موجود في الكتالوج)

DG418DJ+

✅ بديل مباشر
Analog Devices
📦 8-pin PDIP
Precision CMOS analog switch · SPST normally open · 1 channel · 35 ohm maximum · 15 V maximum · 44 V · 100 ns · 35 nW

تواصل لمعرفة السعر

عرض ورقة البيانات ←

DG418LDJ+ الحدود القصوى والخصائص الكهربائية

Number of Circuits 1 circuit
Multiplexer Configuration 1:1
Switch Configuration SPST, normally open
Number of Channels 1 channel
On Resistance 35 ohm maximum
Logic Compatibility +3 V compatible
Minimum Dual Supply Voltage ±4.5 V
Maximum Dual Supply Voltage ±20 V
Turn-Off Time 185 ns maximum
Minimum Operating Temperature -40 C
Maximum Operating Temperature +85 C
Temperature Grade Industrial
العلبة 8-pin PDIP
نمط التركيب Through-hole
Number of Terminals 8 terminals
Supply Configuration Dual supply
حالة RoHS unknown
REACH Status unknown

دليل تكوين أطراف DG418LDJ+ 8-pin pdip

تكوين الأطراف لـ DG418LDJ+ (حزمة 8-pin pdip). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 8-pin pdip لـ DG418LDJ+

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DG418LDJ+.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

DG418LDJ+ مناسب لـ 6 التطبيقs: Precision Test and Measurement Systems, Sensor Signal Routing, Data Acquisition Front Ends, Industrial Control Signal Isolation, Sample-and-Hold Signal Paths, Battery-Powered Portable Instruments.

🔧

Precision Test and Measurement Systems

The DG418LDJ+ fits precision test systems that require a normally open SPST path to isolate instrumentation, DUT terminals, or external fixtures. Its 35 ohm maximum on resistance gives the signal path a defined attenuation ceiling, while the 185 ns maximum turn-off time supports controlled switching between measurement conditions. The 3 V-compatible control interface also permits direct operation from common low-voltage test-controller logic. For high-accuracy measurements, include the switch resistance, leakage, charge injection, and thermal behavior in the measurement error budget. Confirm the final pin connections and signal limits using the manufacturer pin-description table.

🧩

Sensor Signal Routing

The DG418LDJ+ can route sensor signals in acquisition and conditioning systems where the source must remain disconnected until a measurement is requested. The normally open SPST configuration provides a useful default-isolated state, and the 35 ohm maximum on resistance is suitable for many medium-impedance sensor paths. The ±4.5 V to ±20 V dual-supply range accommodates bipolar sensor interfaces, while 3 V-compatible control reduces the need for additional control circuitry. For high-impedance sensors, verify off-state leakage and charge injection because those parameters can dominate the measurement error.

📡

Data Acquisition Front Ends

The DG418LDJ+ is suitable for routing multiplexed analog channels in data-acquisition front ends that require one controlled SPST connection per switch position. Its 35 ohm maximum on resistance is acceptable when the downstream amplifier presents a substantially higher input impedance, and the 185 ns maximum turn-off time enables rapid transition between channels. A 3 V-compatible control input simplifies integration with modern acquisition controllers. Verify bandwidth, off leakage, and channel capacitance for the selected source impedance, because those characteristics determine whether switch loading must be included in the acquisition error budget.

🏭

Industrial Control Signal Isolation

The DG418LDJ+ can isolate a control, sensor, or field-test signal from an analog processing path in industrial equipment. Its normally open behavior provides a defined disconnection state during idle or fault conditions, while dual supplies from ±4.5 V to ±20 V support bipolar industrial signal ranges. The 3 V-compatible control interface allows direct use with modern controller logic. Because industrial systems may present large transients and long cable runs, validate the signal amplitude, supply sequencing, and protection requirements independently of the switch's basic on-resistance and timing ratings.

⚡

Sample-and-Hold Signal Paths

The DG418LDJ+ is appropriate for sample-and-hold or gated-measurement circuits where the analog path is enabled only during a defined sampling interval. The 185 ns maximum turn-off time and 35 ohm maximum on resistance provide useful initial design limits, while the normally open topology allows the source to remain disconnected outside that interval. The 3 V-compatible control input can be driven by a compact timing controller, and the dual ±4.5 V to ±20 V supplies accommodate bipolar node voltages. Check the actual hold capacitor, source impedance, charge injection, and switch leakage before using the component in a high-accuracy sampler.

📱

Battery-Powered Portable Instruments

The DG418LDJ+ can serve as a controllable signal-isolation element in battery-powered portable measurement instruments. The 3 V-compatible control interface aligns with low-voltage digital control, and the ±4.5 V minimum dual supply provides a 9 V total operating range for bipolar signal conditioning. Because the switch can connect or isolate a high-impedance source, it can prevent unwanted loading when the instrument is between measurement phases. Designers should confirm supply current, leakage behavior, and control-logic levels in the manufacturer datasheet and should assess the analog path's sensitivity to switching transients.

ملخص المنتجات الموصى بها

DG418LDJ Same-family normally open analog switch يُستخدم في: Precision Test and Measurement Systems, Sensor Signal Routing, Data Acquisition Front Ends, Industrial Control Signal Isolation, Sample-and-Hold Signal Paths, Battery-Powered Portable Instruments DG418DJ Single-channel SPST switch candidate for evaluation يُستخدم في: Precision Test and Measurement Systems, Sensor Signal Routing, Data Acquisition Front Ends, Industrial Control Signal Isolation, Sample-and-Hold Signal Paths, Battery-Powered Portable Instruments
What is the DG418LDJ+?
The DG418LDJ+ is a single-channel, normally open SPST CMOS analog switch from Analog Devices, with a 35 ohm maximum on resistance and an 8-pin PDIP package. According to the manufacturer datasheet, the device provides one 1:1 switching circuit, operates from dual supplies of ±4.5 V to ±20 V, and accepts 3 V-compatible control logic. It is intended for analog signal routing in test, measurement, instrumentation, data acquisition, and industrial control systems.
What are the key specifications of DG418LDJ+ that engineers should know?
The DG418LDJ+ combines a 1:1, single-channel SPST configuration with 35 ohm maximum on resistance, 3 V logic compatibility, and a ±4.5 V to ±20 V dual-supply operating range. According to the manufacturer datasheet, its maximum turn-off time is 185 ns and its operating temperature range is -40 C to +85 C. The device is packaged in an 8-pin PDIP and is normally open, meaning the switched path is disconnected until the control input activates it.
What is the on resistance of DG418LDJ+?
The DG418LDJ+ has a maximum on resistance of 35 ohm. According to the manufacturer datasheet, this value applies to the closed SPST path when the switch is turned on. Because 35 ohm is a maximum rather than a guaranteed nominal value, designers should use it when evaluating signal attenuation and input-impedance requirements. The complete operating conditions associated with this limit should be checked in the manufacturer datasheet.
What is the supply voltage range of DG418LDJ+?
The DG418LDJ+ operates from ±4.5 V to ±20 V using dual supplies. According to the manufacturer datasheet, this range supports bipolar analog signals while the control input is compatible with 3 V logic. The minimum dual supply is therefore 9 V total, and the maximum is 40 V total. Confirm that signal amplitudes, control levels, and supply tolerances remain inside these operating limits.
Where can I download the DG418LDJ+ datasheet PDF?
The official DG418LDJ+ datasheet PDF is available from the Analog Devices DG418 technical-documentation page at analog.com. The manufacturer datasheet defines the electrical characteristics, pin descriptions, timing, supply requirements, and package dimensions. Use the Analog Devices document as the controlling source when assigning PCB connections or calculating switching performance, and confirm that the document revision applies to the DG418LDJ+ ordering code.
Where can I find the DG418LDJ+ pinout?
The DG418LDJ+ pinout is shown in the pin-description table and package drawing of the manufacturer datasheet. The component is an 8-pin PDIP device, so engineers should assign all eight physical pins from that table rather than infer connections from a generic DIP drawing. Request the manufacturer datasheet through the datasheet link on this page and use the exposed-pin or NC markings exactly as documented.
Is DG418LDJ+ suitable for bipolar instrumentation signals?
Yes, the DG418LDJ+ is suitable for many bipolar instrumentation signals because it supports dual analog supplies from ±4.5 V to ±20 V and uses 3 V-compatible control logic. According to the manufacturer datasheet, the device has 35 ohm maximum on resistance and a 185 ns maximum turn-off time. The signal amplitude, bandwidth, leakage, and charge injection must still be checked against measurement accuracy requirements.
DG418LDJ+ vs DG418DJ - which switch should I choose?
Choose the DG418LDJ+ when the design requires the listed 3 V-compatible control interface and Analog Devices documentation; choose the DG418DJ when its specific Vishay electrical limits better fit the application. Both devices are listed as single-circuit 1:1 analog switches with 35 ohm on resistance in 8-pin PDIP packages. Review each manufacturer datasheet for control thresholds, leakage, timing, and qualification before treating either option as an approved substitute.
When should I choose DG418LDJ+ over DG418LDJ?
Choose the DG418LDJ+ when ordering-code qualification and the stated lead-free product status are required by the procurement specification. The DG418LDJ and DG418LDJ+ share the DG418LDJ base listing and are described as having consistent performance, terminals, and package characteristics. Nevertheless, engineers should verify the exact ordering suffix, marking, and applicable manufacturer documentation before approving either ordering code for production.
What can replace the DG418LDJ+?
The DG418LDJ is the closest same-manufacturer ordering option, while the Vishay DG418DJ is a cross-brand candidate with the same listed 1:1, 35 ohm, 8-pin PDIP configuration. A replacement should not be approved from package appearance alone; verify pin functions, supply range, control thresholds, on resistance, leakage, switching time, and operating temperature against the manufacturer datasheets. Both candidate references are listed as web_data alternatives.
Is DG418LDJ+ the same as DG418DJ?
No. The DG418LDJ+ and DG418DJ share the listed 1:1 single-circuit, 35 ohm, 8-pin PDIP format, but they are sold by different manufacturers and may differ in electrical details, qualification, markings, and lifecycle. According to their individual manufacturer datasheets, both require validation. Treat the DG418DJ as a candidate replacement rather than an unconditional equivalence.
Where can I buy DG418LDJ+ online?
Use the Request a Quote form on this page to request DG418LDJ+ availability, current pricing, order quantity, and lead time. The quote team can confirm the exact 8-pin PDIP ordering code and supply status for your bill of materials. This avoids tying the engineering decision to a temporary distributor listing or an unverified stock message.
What is the price of DG418LDJ+?
Current DG418LDJ+ commercial terms should be obtained through the Request a Quote form on this page. The form lets buyers specify quantity, packaging, and delivery requirements so the quote reflects the current component market rather than a historical catalog figure. Engineers should also request the manufacturer ordering code, lot traceability, and date code needed for their quality system.
What is the lead time and stock status for DG418LDJ+?
Current lead time, stock status, and minimum order quantity for DG418LDJ+ should be confirmed through the Request a Quote form on this page. Some catalog listings may describe immediate shipment, but inventory changes quickly and may not reflect the requested quantity or package. Include your required tube quantity, target date, and approved manufacturer list when requesting the quotation.
How should DG418LDJ+ be used in a precision test system?
Use the DG418LDJ+ as a normally open SPST element when the test system requires the default state to isolate the signal path. According to the manufacturer datasheet, its 35 ohm maximum on resistance, 3 V-compatible control, and ±4.5 V to ±20 V dual-supply range support precision switching applications. Account for attenuation, leakage, charge injection, and switching transient when setting the measurement error budget.

بيانات مرجعية هندسية لـ DG418LDJ+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the DG418LDJ+ when the design needs a single normally open SPST switch with a specified 35 ohm maximum on resistance, 3 V-compatible control, and a ±4.5 V to ±20 V dual-supply range. The DG418LDJ is the closest same-manufacturer alternative when only the ordering suffix differs, but production documentation, markings, and procurement requirements should still be checked. Consider the Vishay DG418DJ only after comparing its pin functions, control thresholds, leakage, bandwidth, switching time, temperature limits, and qualification against the DG418LDJ+ datasheet. Neither candidate should be approved solely from the shared PDIP package. For precision measurements, the switching resistance, leakage, and charge injection must fit the error budget; for high-speed routing, verify bandwidth and capacitance rather than relying only on the 185 ns turn-off figure.

المقارنة مع البدائل

المعامل هذا المنتج DG418LDJ DG418DJ
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Analog Devices Analog Devices Vishay Intertechnology
Number of Circuits 1 circuit 1 circuit 1 circuit
Multiplexer Configuration 1:1 1:1 1:1
Switch Configuration SPST, normally open SPST, normally open SPST, normally open
On Resistance 35 ohm maximum 35 ohm maximum 35 ohm maximum
Mounting Style Through-hole Through-hole Through-hole

أبرز الفروقات

  • Directly identified 3 V-compatible control interface (مقابلDG418DJ)
  • Documented dual-supply operating range (مقابلDG418DJ)
  • Same-family ordering-code alternative (مقابلDG418LDJ)
  • Defined maximum turn-off time (مقابلDG418DJ)

ملاحظات التصميم

Use the 35 ohm maximum on resistance as the worst-case series element in the selected signal path. Check that the source impedance, downstream input impedance, leakage current, and allowed measurement error produce an acceptable attenuation budget. For high-impedance sources, off-state leakage and switch capacitance can be more important than on resistance, so use the complete manufacturer electrical-characteristics table when sizing the front end.

Keep the analog terminals and control input away from noisy clock, relay, and high-current switching paths. Route the switched signal as a short, continuous trace and place the device close to the protected source or measurement input. Maintain adequate spacing between adjacent analog nodes, and use a ground reference appropriate to the circuit's bipolar supply arrangement rather than assuming a single ground connection will handle all return currents.

Do not treat the 3 V-compatible control interface as permission to exceed the control-pin absolute maximum ratings or remove supply sequencing constraints. Confirm the control input thresholds, allowable input voltage, and off-state behavior in the manufacturer datasheet. Also verify that the switched signal remains within the device's analog input range and that both dual supplies remain within ±4.5 V to ±20 V during startup, shutdown, and fault conditions.

Place supply bypass capacitors close to the supply pins and maintain short return paths to the device ground reference. Although the listed operating range permits ±4.5 V to ±20 V, the usable design margin depends on supply tolerance, transient response, and the analog signal amplitude. Review the manufacturer application guidance for the appropriate capacitor values and decoupling topology, and verify logic compatibility when the control supply and analog supplies differ.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The ordering suffix is associated with a lead-free product in catalog references, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration was identified. Automotive qualification is not indicated for this industrial-temperature device.

تم التحقق من البيانات في: 2026-11-16 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

DG418LDJ+ datasheet DG418LDJ+ pinout DG418LDJ+ datasheet pdf DG418LDJ+ equivalent DG418LDJ+ replacement DG418LDJ+ cross reference DG418LDJ+ vs DG418DJ DG418LDJ+ DIP-8 pinout DG418LDJ+ price DG418LDJ+ stock Analog Devices DG418LDJ+ DG418LDJ+ 35 ohm SPST DG418LDJ+ analog switch application

المكونات والمصطلحات ذات الصلة

Analog Devices Maxim Integrated DG418LDJ+ DG418LDJ DG418DJ Vishay Intertechnology SPST analog switch normally open switch analog switch analog multiplexer interface IC CMOS switch 35 ohm on resistance 3 V logic compatibility dual supply PDIP-8 DIP-8 through-hole package signal routing test and measurement data acquisition sensor interface sample-and-hold industrial control charge injection
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر