DS90CF383MTD - 3.3V 65MHz LVDS Transmitter | TI
MPN: DS90CF383MTD ✓ نشطDS90CF383MTD نظرة عامة
An LVDS flat panel display link transmitter is a specialized interface IC within the hierarchy of interface ICs, data converters, LVDS serializers, and semiconductor components. The LVDS standard transmits complementary differential signals whose common-mode rejection helps maintain signal integrity across cables and board interconnects. The DS90CF383MTD is therefore positioned between a parallel pixel-data source and a differential display-link receiver rather than serving as a general-purpose logic or voltage-conversion device.
Three defining capabilities are its 24-bit RGB payload, 65 MHz transmit-clock operation, and 3.3 V supply. According to the Texas Instruments datasheet, each input cycle contains 28 bits, with 24 bits carrying RGB display data and the remaining three bits carrying control information. Four differential LVDS data outputs and a fifth differential clock output provide a compact, high-speed interface for digital display systems. The device also supports transmit-side clocking through a phase-locked transmit clock, allowing the clock and data to be transported together.
The architecture reduces parallel-data fanout by serializing the display payload into low-voltage differential pairs. This can improve noise immunity and reduce connector pin count relative to carrying every parallel pixel bit over a dedicated cable. However, correct implementation depends on matched source and receiver characteristics, controlled trace or cable impedance, compliant LVDS receiver thresholds, and proper termination. The transmitter does not determine the final display resolution by itself; pixel format, timing, and receiver capabilities establish the usable video mode.
Typical uses include LCD and flat-panel monitor links, industrial human-machine interface displays, digital signage, automotive navigation panels, medical imaging displays, and embedded graphics systems. The 65 MHz clock rate supports 24-bit color transfer with additional control signaling when the connected receiver and panel timing are compatible. The device is especially relevant to legacy and established display architectures that use the TI FPD-Link interface rather than newer serialized display standards.
Designers should match the 56-pin TSSOP footprint, observe 3.3 V supply requirements, and implement LVDS routing with short, geometry-controlled connections. Differential pair symmetry matters because mismatched lengths and impedances can create skew and reflections. Decoupling close to the supply pins, an unobstructed ground return, and compliance with the manufacturer’s recommended input and output circuit are essential for reliable operation.
This product page combines the manufacturer’s device description and datasheet information with package details, application guidance, practical layout considerations, and a focused comparison of pin-compatible transmitter options. It is designed to help engineers verify whether the DS90CF383MTD fits an existing FPD-Link design before committing to a board-level redesign or sourcing decision.
بدائل مباشرة لـ DS90CF383MTD — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع DS90CF383MTD (نفس عامل الشكل والبصمة) — يختلف في Input Logic, Product Type.
DS90C383MTD/NOPB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90C383BMT/NOPB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90C383BMTX/NOPB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90CF383MTD/NOPB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN75LVDS83DGG
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90CF383MTD المواصفات
| Device Type | LVDS flat panel display link transmitter |
| جهد التغذية | 3.3 V |
| Transmit Clock Frequency | 65 MHz |
| RGB Data Width | 24 bits |
| Total Parallel Input Width | 28 bits |
| LVDS Data Outputs | 4 differential streams |
| LVDS Clock Outputs | 1 differential stream |
| Input Logic | CMOS/TTL |
| Output Signaling | LVDS |
| LVDS Technology | EIA-644 and TIA-644 |
| Maximum Data Rate | 1820 Mbps |
| درجة حرارة التشغيل | -10 C to 70 C |
| العلبة | 56-pin TSSOP |
| عدد الأطراف | 56 pins |
| نوع التركيب | Surface mount |
| Clocking Architecture | Phase-locked transmit clock |
دليل تكوين أطراف DS90CF383MTD 56-pin tssop
تكوين الأطراف لـ DS90CF383MTD (حزمة 56-pin tssop). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DS90CF383MTD.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
DS90CF383MTD مناسب لـ 6 التطبيقs: LCD Monitor Display Links, Industrial Human-Machine Interfaces, Digital Signage and Video Displays, Automotive Navigation Displays, Medical Imaging and Control Displays, Embedded Graphics and Instrumentation.
LCD Monitor Display Links
The DS90CF383MTD fits an LVDS display link requiring 24-bit color data at a 65 MHz transmit clock. It accepts parallel CMOS/TTL pixel and control information and serializes the payload into four differential data outputs plus a transmitted clock. This reduces the number of high-speed signal conductors reaching the display module and provides a defined architecture for compatible flat-panel controllers. The design should use the manufacturer’s recommended LVDS termination and controlled-impedance routing, while confirming that the selected receiver and panel support the same data format and timing.
موصى به
Industrial Human-Machine Interfaces
DS90CF383MTD is appropriate for industrial HMIs that transfer 24-bit color and control data from a graphics processor to a remote panel controller. Its 65 MHz clock supports established FPD-Link video timing, while differential LVDS signaling helps maintain data integrity across internal cables and board interconnects. The stated -10 C to 70 C operating range suits many indoor industrial environments, but harsher temperature or qualification requirements must be checked separately. Pair the transmitter with a compatible receiver and enforce controlled pair geometry to minimize skew.
موصى به
Digital Signage and Video Displays
The DS90CF383MTD can serialize display data for digital-signage controllers, video-wall nodes, and compact commercial displays that use the TI 65 MHz FPD-Link interface. Its 28-bit parallel input includes 24 RGB bits and three control bits, enabling the display pipeline to carry image data and basic control information through a low-voltage differential link. Compared with routing a wide parallel bus over a cable, the LVDS interface can reduce conductor count and improve noise tolerance. The panel receiver must support matching resolution, refresh timing, and control mapping.
موصى به
Automotive Navigation Displays
DS90CF383MTD can be evaluated for an established automotive navigation or center-display LVDS link that requires 65 MHz, 24-bit FPD-Link operation. Differential data and clock outputs are useful in vehicle electronics because they support reliable signaling over constrained interconnects and reduce parallel routing burden. However, the listed -10 C to 70 C temperature range does not by itself establish automotive qualification, and AEC-Q100 status is not stated. Production use therefore requires confirmation of the exact temperature grade, qualification, receiver compatibility, and electromagnetic requirements.
موصى به
Medical Imaging and Control Displays
DS90CF383MTD is suitable for a medical-control or diagnostic-display interface when the system uses a compatible 65 MHz, 24-bit LVDS FPD-Link architecture. The transmitter delivers pixel and control information through four low-voltage differential data streams and a separate clock stream, which can simplify cable and connector implementation compared with a wide parallel display bus. Signal-integrity verification remains essential because display artifacts can result from pair mismatch, excessive skew, or an incompatible receiver threshold. Confirm medical-device risk requirements, environmental suitability, and system-level image integrity independently.
موصى به
Embedded Graphics and Instrumentation
DS90CF383MTD can connect an embedded graphics engine to a compatible flat-panel controller in test equipment, laboratory instruments, and industrial terminals. Its fixed 65 MHz transmit clock provides a straightforward interface when the supported display mode is already known, while the 56-pin TSSOP package supports conventional surface-mount assembly. Designers should account for the parallel-input timing budget, provide local decoupling, and verify receiver selection before layout release. For adjustable panel timing or multiple clock configurations, a programmable transmitter family may offer greater design flexibility.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ DS90CF383MTD — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DS90C383MTD/NOPB | DS90C383BMT/NOPB | DS90C383BMTX/NOPB | DS90CF383MTD/NOPB | SN75LVDS83DGG |
|---|---|---|---|---|---|---|
| Package | 56-pin TSSOP | 56-pin TSSOP - same | 56-pin TSSOP - same | 56-pin TSSOP - same | 56-pin TSSOP - same | 56-pin TSSOP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Function | 24-bit FPD-Link LVDS transmitter | 24-bit FPD-Link LVDS transmitter | Programmable LVDS flat-panel display transmitter | Programmable LVDS flat-panel display transmitter | 24-bit FPD-Link LVDS transmitter | LVDS line and bus driver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| LVDS Data Outputs | 4 differential streams plus 1 clock stream | 4 differential streams plus 1 clock stream | LVDS flat-panel display transmitter | LVDS flat-panel display transmitter | 4 differential streams plus 1 clock stream | LVDS line and bus driver |
أبرز الفروقات
- Fixed 65 MHz FPD-Link operation (مقابلDS90C383BMT/NOPB)
- Explicit 24-bit RGB and four-differential-stream implementation (مقابلSN75LVDS83DGG)
- Matching 56-pin TSSOP footprint (مقابلDS90CF383MTD/NOPB)
- Complete 28-bit parallel input interface (مقابلDS90C383BMTX/NOPB)
ملاحظات التصميم
Route the four LVDS data pairs and the differential clock pair as controlled-impedance, tightly coupled traces with minimal layer transitions and vias. Match the geometry of each differential pair and maintain a continuous ground reference beneath the route. The parallel CMOS/TTL inputs and transmitted clock can create edge-rate current, so avoid running the LVDS pairs adjacent to switching-power nodes or unrelated high-speed lines.
Do not treat every 56-pin LVDS transmitter as an automatic replacement for the DS90CF383MTD. The B-family devices use programmable behavior, while the SN75LVDS83DGG is identified as an LVDS line and bus driver. Before replacing the device, compare power pins, clock inputs, data mapping, LVDS output mapping, control logic, reset requirements, and the companion receiver in the manufacturer pin-description tables.
Place the recommended 3.3 V decoupling capacitors at the device supply pins and provide a low-impedance ground return. Keep the transmitter and associated LVDS circuitry away from noisy sources where practical. Because the device includes a phase-locked transmit clock, monitor power sequencing and clock stability at the receiver; an apparently correct LVDS waveform can still produce display errors when clock timing or source-to-receiver skew is outside system limits.
Validate the complete transmitter-to-receiver path with the intended cable or PCB interconnect. Check differential input thresholds, termination values, pair length matching, and the receiver’s clock-recovery capability under the required pixel clock and data rate. Use eye-oriented measurements for production validation when the display link operates near its timing limits, and avoid substituting connector or cable geometry without repeating those checks.
معلومات الامتثال
The DS90CF383MTD is an integrated interface IC rather than an automotive-qualified power device. The accessible device information does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The NOPB suffix appears in related ordering records, but a lead-free or halogen-free declaration should not be inferred solely from that suffix.