Texas Instruments

DS90CF383MTD - 3.3V 65MHz LVDS Transmitter | TI

MPN: DS90CF383MTD ✓ فعال
3.3 V Vdss 56-pin TSSOP Package 65 MHz Speed
حداقل سفارش: 1 |

DS90CF383MTD نمای کلی

Texas Instruments DS90CF383MTD is a 3.3 V, 65 MHz, 24-bit flat panel display link transmitter in a 56-pin TSSOP package. It converts 28 CMOS/TTL input bits into four LVDS data streams and one differential clock stream, transmitting 24 RGB data bits plus three control bits on every transmit-clock cycle. The interface uses low-voltage differential signaling for reliable point-to-point transfer of high-speed display data between a graphics engine and a flat-panel display controller.

An LVDS flat panel display link transmitter is a specialized interface IC within the hierarchy of interface ICs, data converters, LVDS serializers, and semiconductor components. The LVDS standard transmits complementary differential signals whose common-mode rejection helps maintain signal integrity across cables and board interconnects. The DS90CF383MTD is therefore positioned between a parallel pixel-data source and a differential display-link receiver rather than serving as a general-purpose logic or voltage-conversion device.

Three defining capabilities are its 24-bit RGB payload, 65 MHz transmit-clock operation, and 3.3 V supply. According to the Texas Instruments datasheet, each input cycle contains 28 bits, with 24 bits carrying RGB display data and the remaining three bits carrying control information. Four differential LVDS data outputs and a fifth differential clock output provide a compact, high-speed interface for digital display systems. The device also supports transmit-side clocking through a phase-locked transmit clock, allowing the clock and data to be transported together.

The architecture reduces parallel-data fanout by serializing the display payload into low-voltage differential pairs. This can improve noise immunity and reduce connector pin count relative to carrying every parallel pixel bit over a dedicated cable. However, correct implementation depends on matched source and receiver characteristics, controlled trace or cable impedance, compliant LVDS receiver thresholds, and proper termination. The transmitter does not determine the final display resolution by itself; pixel format, timing, and receiver capabilities establish the usable video mode.

Typical uses include LCD and flat-panel monitor links, industrial human-machine interface displays, digital signage, automotive navigation panels, medical imaging displays, and embedded graphics systems. The 65 MHz clock rate supports 24-bit color transfer with additional control signaling when the connected receiver and panel timing are compatible. The device is especially relevant to legacy and established display architectures that use the TI FPD-Link interface rather than newer serialized display standards.

Designers should match the 56-pin TSSOP footprint, observe 3.3 V supply requirements, and implement LVDS routing with short, geometry-controlled connections. Differential pair symmetry matters because mismatched lengths and impedances can create skew and reflections. Decoupling close to the supply pins, an unobstructed ground return, and compliance with the manufacturer’s recommended input and output circuit are essential for reliable operation.

This product page combines the manufacturer’s device description and datasheet information with package details, application guidance, practical layout considerations, and a focused comparison of pin-compatible transmitter options. It is designed to help engineers verify whether the DS90CF383MTD fits an existing FPD-Link design before committing to a board-level redesign or sourcing decision.

جایگزین‌های drop-in برای DS90CF383MTD — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای DS90CF383MTD (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Input Logic, Product Type.

Texas Instruments
Product Type: 3.3 V programmable LVDS transmitter
مقایسه با DS90CF383MTD →
Texas Instruments
Input Logic: LVCMOS/LVTTL
Product Type: Programmable LVDS flat-panel display transmitter
مقایسه با DS90CF383MTD →

DS90C383MTD/NOPB

✅ جایگزین مستقیم
📦 56-pin TSSOP
Same 3.3 V, 65 MHz, 24-bit FPD-Link role; suffix-specific lead finish differs, with no quantified electrical change

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90C383BMT/NOPB

✅ جایگزین مستقیم
📦 56-pin TSSOP
Uses programmable LVDS behavior while retaining a 56-pin TSSOP package; advertised comparison rate differs by up to 46% from 1820 Mbps

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90C383BMTX/NOPB

✅ جایگزین مستقیم
📦 56-pin TSSOP
Programmable B-family transmitter in the same 56-pin TSSOP footprint; advertised comparison rate differs by up to 46% from 1820 Mbps

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90CF383MTD/NOPB

✅ جایگزین مستقیم
📦 56-pin TSSOP
Same electrical platform and 56-pin TSSOP footprint; NOPB ordering suffix indicates a different lead-finish configuration

📋 جایگزین مرجع (خارج از کاتالوگ)

SN75LVDS83DGG

✅ جایگزین مستقیم
📦 56-pin TSSOP
Same 56-pin TSSOP and LVDS class but different FPD-Link clock and pin-function configuration must be verified; match limited to 70%

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90CF383MTD مشخصات

Device Type LVDS flat panel display link transmitter
ولتاژ تغذیه 3.3 V
Transmit Clock Frequency 65 MHz
RGB Data Width 24 bits
Total Parallel Input Width 28 bits
LVDS Data Outputs 4 differential streams
LVDS Clock Outputs 1 differential stream
Input Logic CMOS/TTL
Output Signaling LVDS
LVDS Technology EIA-644 and TIA-644
Maximum Data Rate 1820 Mbps
دمای کاری -10 C to 70 C
بسته‌بندی 56-pin TSSOP
تعداد پایه 56 pins
نوع نصب Surface mount
Clocking Architecture Phase-locked transmit clock

راهنمای پیکربندی پین DS90CF383MTD 56-pin tssop

پیکربندی پین برای DS90CF383MTD (پکیج 56-pin tssop). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 56-pin tssop برای DS90CF383MTD

داده پین‌آوت تفصیلی موجود نیست برای DS90CF383MTD.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

DS90CF383MTD مناسب است برای 6 کاربردs: LCD Monitor Display Links, Industrial Human-Machine Interfaces, Digital Signage and Video Displays, Automotive Navigation Displays, Medical Imaging and Control Displays, Embedded Graphics and Instrumentation.

📺

LCD Monitor Display Links

The DS90CF383MTD fits an LVDS display link requiring 24-bit color data at a 65 MHz transmit clock. It accepts parallel CMOS/TTL pixel and control information and serializes the payload into four differential data outputs plus a transmitted clock. This reduces the number of high-speed signal conductors reaching the display module and provides a defined architecture for compatible flat-panel controllers. The design should use the manufacturer’s recommended LVDS termination and controlled-impedance routing, while confirming that the selected receiver and panel support the same data format and timing.

🏭

Industrial Human-Machine Interfaces

DS90CF383MTD is appropriate for industrial HMIs that transfer 24-bit color and control data from a graphics processor to a remote panel controller. Its 65 MHz clock supports established FPD-Link video timing, while differential LVDS signaling helps maintain data integrity across internal cables and board interconnects. The stated -10 C to 70 C operating range suits many indoor industrial environments, but harsher temperature or qualification requirements must be checked separately. Pair the transmitter with a compatible receiver and enforce controlled pair geometry to minimize skew.

📺

Digital Signage and Video Displays

The DS90CF383MTD can serialize display data for digital-signage controllers, video-wall nodes, and compact commercial displays that use the TI 65 MHz FPD-Link interface. Its 28-bit parallel input includes 24 RGB bits and three control bits, enabling the display pipeline to carry image data and basic control information through a low-voltage differential link. Compared with routing a wide parallel bus over a cable, the LVDS interface can reduce conductor count and improve noise tolerance. The panel receiver must support matching resolution, refresh timing, and control mapping.

🚗

Automotive Navigation Displays

DS90CF383MTD can be evaluated for an established automotive navigation or center-display LVDS link that requires 65 MHz, 24-bit FPD-Link operation. Differential data and clock outputs are useful in vehicle electronics because they support reliable signaling over constrained interconnects and reduce parallel routing burden. However, the listed -10 C to 70 C temperature range does not by itself establish automotive qualification, and AEC-Q100 status is not stated. Production use therefore requires confirmation of the exact temperature grade, qualification, receiver compatibility, and electromagnetic requirements.

💊

Medical Imaging and Control Displays

DS90CF383MTD is suitable for a medical-control or diagnostic-display interface when the system uses a compatible 65 MHz, 24-bit LVDS FPD-Link architecture. The transmitter delivers pixel and control information through four low-voltage differential data streams and a separate clock stream, which can simplify cable and connector implementation compared with a wide parallel display bus. Signal-integrity verification remains essential because display artifacts can result from pair mismatch, excessive skew, or an incompatible receiver threshold. Confirm medical-device risk requirements, environmental suitability, and system-level image integrity independently.

🔧

Embedded Graphics and Instrumentation

DS90CF383MTD can connect an embedded graphics engine to a compatible flat-panel controller in test equipment, laboratory instruments, and industrial terminals. Its fixed 65 MHz transmit clock provides a straightforward interface when the supported display mode is already known, while the 56-pin TSSOP package supports conventional surface-mount assembly. Designers should account for the parallel-input timing budget, provide local decoupling, and verify receiver selection before layout release. For adjustable panel timing or multiple clock configurations, a programmable transmitter family may offer greater design flexibility.

What is the DS90CF383MTD used for?
The DS90CF383MTD is a 3.3 V LVDS transmitter used to transfer 24-bit flat-panel display data over a high-speed differential link. According to the Texas Instruments datasheet, it samples 28 CMOS/TTL input bits and converts them into four LVDS data streams plus a fifth differential clock stream. It is suitable for LCD monitors, industrial HMIs, digital signage, and other systems using the TI 65 MHz FPD-Link architecture.
What is the operating voltage of DS90CF383MTD?
The DS90CF383MTD operates from a 3.3 V supply. The Texas Instruments product page identifies it as a 3.3 V LVDS transmitter, while the device listing identifies a 56-pin TSSOP package. The supply rail must be decoupled according to the manufacturer’s recommended application circuit, and input levels must remain compatible with the device’s CMOS/TTL input interface.
What is the maximum clock frequency of DS90CF383MTD?
The DS90CF383MTD has a 65 MHz transmit clock. At each transmit-clock cycle, the device samples 28 parallel input bits and sends 24 RGB bits plus three control bits through the LVDS data outputs. According to the Texas Instruments datasheet, the transmitted clock runs in parallel with the data streams over a fifth LVDS link.
How many bits can DS90CF383MTD transmit?
The DS90CF383MTD accepts 28 parallel CMOS/TTL bits and transfers 24 RGB data bits plus three control bits per transmit-clock cycle. Its output consists of four differential LVDS data streams and one differential clock stream. The resulting differential payload is associated with a maximum data rate of 1820 Mbps in the component comparison information.
Where can I download the DS90CF383MTD datasheet PDF?
The official DS90CF383MTD datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90cf383.pdf. The document contains the device block diagram, electrical characteristics, pin information, operating details, and recommended application circuitry. It is the preferred source for final schematic, layout, and signal-integrity decisions.
Where can I find the DS90CF383MTD pinout?
The DS90CF383MTD pinout is documented in the Texas Instruments DS90CF383 datasheet. The device uses a 56-pin TSSOP package, and the pin-description table should be used to assign data, control, clock, power, ground, and reserved connections during schematic capture. The public listing excerpts do not reproduce every numbered pin assignment, so use the manufacturer PDF for board construction.
What package does DS90CF383MTD use?
The DS90CF383MTD uses a 56-pin TSSOP surface-mount package. Component listings identify it as a 56-TSSOP interface IC, and the package is also described as PDSO56. Its mechanical outline, pin pitch, exposed thermal information, and solder pattern should be taken from the manufacturer package drawing associated with the DS90CF383 documentation.
What is the difference between DS90CF383MTD and DS90C383MTD?
Both devices are identified as 3.3 V, 24-bit, 65 MHz LVDS flat-panel display transmitters, and both appear in 56-pin TSSOP listings. The available component records do not establish every electrical difference, so engineers should compare the ordering information and pin-description tables for the exact suffix before substitution. DS90C383MTD/NOPB is a reasonable candidate only after confirming the selected package code and signal mapping.
Is DS90CF383MTD the same as DS90C383BMT?
DS90CF383MTD and DS90C383BMT are related Texas Instruments FPD-Link transmitters, but they are not automatically interchangeable in every design. A documented comparison lists DS90C383BMT as a 56-pin TSSOP 3 V programmable transmitter, while the DS90CF383MTD is a fixed-function 65 MHz transmitter. Verify pin functions, electrical limits, clock behavior, and input timing before treating one as a drop-in replacement.
What can replace DS90CF383MTD?
DS90C383MTD/NOPB is the closest same-family replacement candidate because it is a 3.3 V, 24-bit, 65 MHz, 56-pin TSSOP FPD-Link transmitter. Other candidates include DS90C383BMT/NOPB and DS90C383BMTX/NOPB, but their programmable behavior and suffix-specific details require verification. A replacement is suitable only when the footprint, pin functions, electrical limits, and interface timing match the original board.
Can SN75LVDS83DGG replace DS90CF383MTD?
SN75LVDS83DGG is a possible 56-pin TSSOP LVDS-family alternative, but it is not a confirmed drop-in replacement for DS90CF383MTD. The comparison identifies both as 56-pin devices and relates their electrical characteristics, yet the available records do not prove identical pin mapping or FPD-Link clock behavior. Verify the SN75LVDS83DGG datasheet and receiver ecosystem before changing the transmitter.
When should I choose DS90CF383MTD over a programmable LVDS transmitter?
Choose DS90CF383MTD when the display architecture already uses the TI 65 MHz 24-bit FPD-Link interface and the board requires a fixed, established 56-pin TSSOP transmitter. A programmable variant may be preferable when clocking must be adjusted or configured across different display modes. The decision should be based on the complete transmitter and receiver pairing, supported resolutions, and PCB compatibility.
Is DS90CF383MTD suitable for industrial display applications?
DS90CF383MTD is suitable for display links whose environmental requirements fall within its stated -10 C to 70 C operating-temperature range. The transmitter can support industrial HMI, control-panel, medical-display, and signage interfaces when paired with a compatible receiver. For wider temperature exposure or automotive production requirements, verify the qualification status and temperature grade before design release.
Where can I buy DS90CF383MTD online?
Use the Request a Quote form on this page to request DS90CF383MTD pricing, current availability, and lead time for your required quantity and packaging. The structured price evidence contains no qualifying quantity-break listing, so this page does not present a static unit price or stock claim. Confirm the exact MTD ordering suffix before submitting the request.
What are the key specifications of DS90CF383MTD that engineers should know?
The key DS90CF383MTD specifications are a 3.3 V supply, 65 MHz transmit clock, 24-bit RGB payload, four differential LVDS data outputs, one differential clock output, and a 56-pin TSSOP package. The device also uses CMOS/TTL parallel inputs, supports EIA-644 and TIA-644 signaling, and is listed for operation from -10 C to 70 C.
How should DS90CF383MTD LVDS traces be routed?
Route each LVDS differential pair as a tightly coupled, impedance-controlled pair with minimal vias and matched length where receiver timing requires it. Keep the pairs away from noisy switching paths, preserve a continuous ground reference, and follow the manufacturer’s recommended input and output network. The 65 MHz clock and parallel data inputs also require clean supply-return paths to minimize edge jitter and common-mode conversion.

داده‌های مرجع مهندسی برای DS90CF383MTD — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose DS90CF383MTD when rebuilding or maintaining an established TI FPD-Link system that uses a 65 MHz transmit clock, 24-bit RGB data, and a 56-pin TSSOP footprint. Its fixed operation is straightforward when the supported panel timing and receiver are already defined. DS90C383MTD/NOPB is the closest same-family candidate when the assembly finish permits changing the NOPB suffix. Consider DS90C383BMT/NOPB or DS90C383BMTX/NOPB when programmable transmitter behavior adds value, but verify their clocking and pin configuration against the original board. SN75LVDS83DGG is a broader LVDS line-driver candidate and should be considered only after its pin mapping, receiver pairing, timing, and application circuit are confirmed. For any replacement, verify the exact ordering suffix, package drawing, electrical limits, LVDS network, and compatible receiver before committing to a board revision.

مقایسه با جایگزین‌ها

پارامتر این محصول DS90C383MTD/NOPB DS90C383BMT/NOPB DS90C383BMTX/NOPB DS90CF383MTD/NOPB SN75LVDS83DGG
Package 56-pin TSSOP 56-pin TSSOP - same 56-pin TSSOP - same 56-pin TSSOP - same 56-pin TSSOP - same 56-pin TSSOP - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Device Function 24-bit FPD-Link LVDS transmitter 24-bit FPD-Link LVDS transmitter Programmable LVDS flat-panel display transmitter Programmable LVDS flat-panel display transmitter 24-bit FPD-Link LVDS transmitter LVDS line and bus driver
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
LVDS Data Outputs 4 differential streams plus 1 clock stream 4 differential streams plus 1 clock stream LVDS flat-panel display transmitter LVDS flat-panel display transmitter 4 differential streams plus 1 clock stream LVDS line and bus driver

تفاوت‌های کلیدی

  • Fixed 65 MHz FPD-Link operation (در مقابلDS90C383BMT/NOPB)
  • Explicit 24-bit RGB and four-differential-stream implementation (در مقابلSN75LVDS83DGG)
  • Matching 56-pin TSSOP footprint (در مقابلDS90CF383MTD/NOPB)
  • Complete 28-bit parallel input interface (در مقابلDS90C383BMTX/NOPB)

یادداشت‌های طراحی

Route the four LVDS data pairs and the differential clock pair as controlled-impedance, tightly coupled traces with minimal layer transitions and vias. Match the geometry of each differential pair and maintain a continuous ground reference beneath the route. The parallel CMOS/TTL inputs and transmitted clock can create edge-rate current, so avoid running the LVDS pairs adjacent to switching-power nodes or unrelated high-speed lines.

Do not treat every 56-pin LVDS transmitter as an automatic replacement for the DS90CF383MTD. The B-family devices use programmable behavior, while the SN75LVDS83DGG is identified as an LVDS line and bus driver. Before replacing the device, compare power pins, clock inputs, data mapping, LVDS output mapping, control logic, reset requirements, and the companion receiver in the manufacturer pin-description tables.

Place the recommended 3.3 V decoupling capacitors at the device supply pins and provide a low-impedance ground return. Keep the transmitter and associated LVDS circuitry away from noisy sources where practical. Because the device includes a phase-locked transmit clock, monitor power sequencing and clock stability at the receiver; an apparently correct LVDS waveform can still produce display errors when clock timing or source-to-receiver skew is outside system limits.

Validate the complete transmitter-to-receiver path with the intended cable or PCB interconnect. Check differential input thresholds, termination values, pair length matching, and the receiver’s clock-recovery capability under the required pixel clock and data rate. Use eye-oriented measurements for production validation when the display link operates near its timing limits, and avoid substituting connector or cable geometry without repeating those checks.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The DS90CF383MTD is an integrated interface IC rather than an automotive-qualified power device. The accessible device information does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The NOPB suffix appears in related ordering records, but a lead-free or halogen-free declaration should not be inferred solely from that suffix.

تاریخ تأیید داده‌ها: 2026-11-10 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

DS90CF383MTD DS90CF383MTD datasheet DS90CF383MTD datasheet pdf DS90CF383MTD pinout DS90CF383MTD specifications DS90CF383MTD equivalent DS90CF383MTD replacement DS90CF383MTD cross reference DS90CF383MTD vs DS90C383BMT Texas Instruments DS90CF383MTD DS90CF383MTD 56-TSSOP DS90CF383MTD 65MHz LVDS DS90CF383MTD flat panel display link DS90CF383MTD price

قطعات و اصطلاحات مرتبط

Texas Instruments DS90CF383MTD DS90C383MTD/NOPB DS90C383BMT/NOPB DS90C383BMTX/NOPB DS90CF383MTD/NOPB SN75LVDS83DGG LVDS low-voltage differential signaling FPD-Link flat panel display link LVDS transmitter interface IC line and bus driver CMOS/TTL phase-locked transmit clock 24-bit RGB 65 MHz transmit clock 3.3 V power supply 56-pin TSSOP TSSOP package family surface-mount package EIA-644 TIA-644 industrial display
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ