DSPIC30F5015-30I/PT - 30 MIPS 16-bit DSC, 66KB Flash | Microchip
MPN: DSPIC30F5015-30I/PT ✓ نشطDSPIC30F5015-30I/PT نظرة عامة
A Digital Signal Controller (DSC) is a class of embedded processor that combines a microcontroller (MCU) with a dedicated Digital Signal Processor (DSP) engine on the same silicon die. Within the broader semiconductor taxonomy, a DSC sits between a microcontroller and a full DSP: MCU -> DSC -> DSP -> embedded processor -> semiconductor. DSCs target applications that need deterministic real-time control (PWM, timers, ADC sampling) plus on-chip DSP math (IIR/FIR filters, FFTs, motor vector control), and the dsPIC30F family specifically targets 5 V-tolerant industrial designs that older 3.3 V parts cannot serve.
Key differentiating specifications include 8 KB of auxiliary Flash, 1024 bytes of EEPROM, a 12-bit ADC with 16 channels and 200 ksps throughput, five 16-bit timers, four PWM channels with duty-cycle resolution suitable for motor drive, two UART, two SPI, one I2C, and one CAN module. The device supports 3.0 V to 5.5 V single-supply operation, ideal for industrial 5 V rails.
Architecture-wise, the part uses a 24-bit instruction word with 16-bit data paths, separate program and data buses for single-cycle MAC, and an interrupt controller with 5-cycle latency. The 64-pin TQFP supports a wide operating temperature range of -40 °C to +85 °C (industrial grade), with Flash endurance of 10,000 erase/write cycles minimum.
Typical applications include brushless DC (BLDC) and AC induction motor control, uninterruptible power supplies (UPS), power conversion inverters, automotive sensor conditioning, and industrial sensorless motor drives. The combination of deterministic PWM, fast ADC, and on-chip DSP math removes the need for an external DSP coprocessor.
When designing with this part, allocate the external 8 MHz to 10 MHz primary oscillator budget carefully because the 40 MHz system clock is derived from a PLL multiplier. Verify that the 5 V-tolerant I/O pin count matches your isolation interface, and remember that 66 KB of Flash includes both code and auxiliary storage.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
بدائل مباشرة لـ DSPIC30F5015-30I/PT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع DSPIC30F5015-30I/PT (نفس عامل الشكل والبصمة) — يختلف في Package, ADC, Core Architecture, Operating Temperature, Timers.
DSPIC30F5011-30I/PT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F4013-30I/P
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F4012-30I/ML
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F5015-20E/PT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F5015T-30I/PT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F4013-20I/PT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F4011-30I/P
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F5015-30I/PT الحدود القصوى والخصائص الكهربائية
| Core Architecture | dsPIC30F, 16-bit modified Harvard |
| CPU Performance | 30 MIPS (40 MHz max CPU clock) |
| Program Memory (Flash) | 66 KB (including 8 KB auxiliary Flash) |
| Data RAM | 2 KB |
| Data EEPROM | 1024 bytes |
| ADC | 12-bit, 16 channels, 200 ksps |
| PWM Channels | 4 (16-bit, motor-control optimized) |
| Timers | Five 16-bit timers |
| UART | 2 modules |
| SPI | 2 modules |
| I2C | 1 module |
| CAN | 1 module |
| جهد التغذية | 3.0 V to 5.5 V |
| درجة حرارة التشغيل | -40 °C to +85 °C (industrial, I suffix) |
| العلبة | 64-pin TQFP (PT), 10 mm x 10 mm |
| نوع التركيب | Surface Mount |
| مستوى MSL | 3 (168 hours) |
| حالة RoHS | Compliant |
تكوين أطراف DSPIC30F5015-30I/PT
| دبوس 1 | AN0/VREF+/CN2/RB0 — Analog input 0 / positive reference / CN2 / I/O port B0 |
| دبوس 2 | AN1/VREF-/CN3/RB1 — Analog input 1 / negative reference / CN3 / I/O port B1 |
| دبوس 3 | AN2/CN4/RB2 — Analog input 2 / CN4 / I/O port B2 |
| دبوس 4 | AN3/CN5/RB3 — Analog input 3 / CN5 / I/O port B3 |
| دبوس 5 | AN4/CN6/RB4 — Analog input 4 / CN6 / I/O port B4 |
| دبوس 6 | AN5/CN7/RB5 — Analog input 5 / CN7 / I/O port B5 |
| دبوس 7 | AN6/OCFA/RB6 — Analog input 6 / Output Compare fault A / I/O port B6 |
| دبوس 8 | AN7/RB7 — Analog input 7 / I/O port B7 |
| دبوس 9 | AN8/RC0 — Analog input 8 / I/O port C0 |
| دبوس 10 | AN9/RC1 — Analog input 9 / I/O port C1 |
| دبوس 11 | AN10/CN8/RC2 — Analog input 10 / CN8 / I/O port C2 |
| دبوس 12 | AN11/CN9/RC3 — Analog input 11 / CN9 / I/O port C3 |
| دبوس 13 | AN12/CN10/RC4 — Analog input 12 / CN10 / I/O port C4 |
| دبوس 14 | OSC2/CLKO/RC15 — Oscillator output / system clock out / I/O port C15 |
| دبوس 15 | OSC1/CLKI/RC14 — Oscillator input / system clock in / I/O port C14 |
| دبوس 16 | VDD — Digital supply voltage (3.0V to 5.5V) |
| دبوس 17 | MCLR — Master Clear reset input (active low) |
| دبوس 18 | PGED1/EMU1/RF4 — ICSP programming data / I/O port F4 |
| دبوس 19 | PGEC1/EMU0/RF5 — ICSP programming clock / I/O port F5 |
| دبوس 20 | PGED2/RF6 — ICSP data 2 / I/O port F6 |
| دبوس 21 | PGEC2/RF7 — ICSP clock 2 / I/O port F7 |
| دبوس 22 | SDA1/RG3 — I2C1 data / I/O port G3 |
| دبوس 23 | SCL1/RG2 — I2C1 clock / I/O port G2 |
| دبوس 24 | U1TX/RF3 — UART1 transmit / I/O port F3 |
| دبوس 25 | U1RX/RF2 — UART1 receive / I/O port F2 |
| دبوس 26 | U2TX/RF1 — UART2 transmit / I/O port F1 |
| دبوس 27 | U2RX/RF0 — UART2 receive / I/O port F0 |
| دبوس 28 | SCK1/INT0/RD8 — SPI1 clock / external interrupt 0 / I/O port D8 |
| دبوس 29 | SDI1/RD9 — SPI1 data in / I/O port D9 |
| دبوس 30 | SDO1/RD10 — SPI1 data out / I/O port D10 |
| دبوس 31 | SS1/RD11 — SPI1 slave select / I/O port D11 |
| دبوس 32 | SCK2/RG6 — SPI2 clock / I/O port G6 |
| دبوس 33 | SDI2/RG7 — SPI2 data in / I/O port G7 |
| دبوس 34 | SDO2/RG8 — SPI2 data out / I/O port G8 |
| دبوس 35 | SS2/RG9 — SPI2 slave select / I/O port G9 |
| دبوس 36 | C1TX/RD12 — CAN1 transmit / I/O port D12 |
| دبوس 37 | C1RX/RD13 — CAN1 receive / I/O port D13 |
| دبوس 38 | VSS — Digital ground |
| دبوس 39 | PWM1H/RD0 — PWM1 high-side output / I/O port D0 |
| دبوس 40 | PWM1L/RD1 — PWM1 low-side output / I/O port D1 |
| دبوس 41 | PWM2H/RD2 — PWM2 high-side output / I/O port D2 |
| دبوس 42 | PWM2L/RD3 — PWM2 low-side output / I/O port D3 |
| دبوس 43 | PWM3H/RD4 — PWM3 high-side output / I/O port D4 |
| دبوس 44 | PWM3L/RD5 — PWM3 low-side output / I/O port D5 |
| دبوس 45 | PWM4H/RE0 — PWM4 high-side output / I/O port E0 |
| دبوس 46 | PWM4L/RE1 — PWM4 low-side output / I/O port E1 |
| دبوس 47 | T1CK/RC13 — Timer1 clock / I/O port C13 |
| دبوس 48 | T2CK/RC14 — Timer2 clock / I/O port C14 |
| دبوس 49 | T3CK/RE3 — Timer3 clock / I/O port E3 |
| دبوس 50 | T4CK/RE4 — Timer4 clock / I/O port E4 |
| دبوس 51 | T5CK/RE5 — Timer5 clock / I/O port E5 |
| دبوس 52 | FLTA/INT1/RE6 — PWM fault A / external interrupt 1 / I/O port E6 |
| دبوس 53 | FLTB/INT2/RE7 — PWM fault B / external interrupt 2 / I/O port E7 |
| دبوس 54 | QEA/RA8 — Quadrature encoder A / I/O port A8 |
| دبوس 55 | QEB/RA9 — Quadrature encoder B / I/O port A9 |
| دبوس 56 | INDX/RA10 — Quadrature index / I/O port A10 |
| دبوس 57 | AVDD — Analog supply voltage (tie to VDD) |
| دبوس 58 | AVSS — Analog ground (tie to VSS) |
| دبوس 59 | AN13/CN11/RB8 — Analog input 13 / CN11 / I/O port B8 |
| دبوس 60 | AN14/CN12/RB9 — Analog input 14 / CN12 / I/O port B9 |
| دبوس 61 | AN15/CN13/RB10 — Analog input 15 / CN13 / I/O port B10 |
| دبوس 62 | INT3/RA11 — External interrupt 3 / I/O port A11 |
| دبوس 63 | INT4/RA12 — External interrupt 4 / I/O port A12 |
| دبوس 64 | VDD — Digital supply voltage (3.0V to 5.5V) |
التطبيقات النموذجية
DSPIC30F5015-30I/PT مناسب لـ 6 التطبيقs: Brushless DC (BLDC) Motor Control, AC Induction Motor VFD, Uninterruptible Power Supply (UPS) Control, Solar Micro-Inverter Control, Industrial Sensor Conditioning & DSP Front-End, Automotive Sensor / Actuator ECU (Non-Safety).
Brushless DC (BLDC) Motor Control
The DSPIC30F5015-30I/PT is purpose-built for 3-phase BLDC and PMSM motor drives thanks to its on-chip 4-channel PWM with complementary outputs and programmable dead-time, the 12-bit 200 ksps ADC capable of sampling phase currents simultaneously, and the 40-bit DSP accumulator executing Park/Clarke transforms in single cycles. Placed at the heart of a sensorless FOC algorithm running at 20 kHz loop rate, the part drives 24 V to 48 V BLDC motors up to several hundred watts without an external DSP coprocessor, while the 66 KB Flash accommodates full state-machine plus firmware update image storage. According to Microchip's Motor Control Family Reference Manual (DS70046), the device delivers deterministic torque control with <1 µs interrupt latency for the ADC pair trigger.
موصى به
AC Induction Motor VFD
Variable-frequency drives (VFDs) for AC induction motors use the DSPIC30F5015-30I/PT to generate sinusoidal PWM with field-oriented control. The part's 30 MIPS throughput, dual 16-channel ADC trigger support, and quadrature encoder interface let designers implement sensorless and encoder-based VFD algorithms on a single chip. The 5 V-tolerant I/O simplifies gate-driver interfacing to high-voltage IGBT bridges, while the CAN module supports industrial Fieldbus / Modbus integration in factory automation. Per Microchip's dsPIC30F family documentation, the device handles 4-quadrant regenerative braking math natively without offloading to an external DSP.
موصى به
Uninterruptible Power Supply (UPS) Control
Online and line-interactive UPS systems use the DSPIC30F5015-30I/PT as the central DSP for inverter control, battery management, and grid synchronization. The 66 KB Flash stores inverter PWM, sine-table, and MPPT-style battery charging algorithms, while the 12-bit ADC samples DC bus voltage, battery current, and AC output simultaneously at 200 ksps. The CAN module enables communication with system-level BMS controllers. Compared with general-purpose MCUs, the 40-bit DSP accumulator enables fast RMS and harmonic calculations critical for THD <3% inverter output per UL 1778 requirements.
موصى به
Solar Micro-Inverter Control
Micro-inverters attach to individual photovoltaic panels and need compact DSP-grade control. The DSPIC30F5015-30I/PT fits by providing 30 MIPS for MPPT and grid-tie PLL, dual PWM for push-pull or full-bridge topologies, and an integrated CAN module for module-level monitoring. Its industrial -40 °C to +85 °C rating survives outdoor rooftop enclosures, and 66 KB of Flash accommodates both MPPT and grid-synchronization code plus lookup tables for sine-triangle PWM. The 5 V I/O tolerance eases interfacing to 600 V MOSFET gate drivers without level shifters.
موصى به
Industrial Sensor Conditioning & DSP Front-End
Strain-gauge bridges, thermocouples, and load cells benefit from the DSPIC30F5015-30I/PT's 12-bit 200 ksps ADC plus on-chip DSP math for digital filtering. The 66 KB Flash stores 256-tap FIR coefficients for 50/60 Hz notch filters, while 2 KB RAM supports sample buffering for FFT analysis up to 1024 points. The integrated CAN module publishes conditioned sensor data at 1 Mbaud on industrial CANopen networks, and the 5 V I/O tolerance simplifies interfacing to legacy industrial 5 V transducer front-ends without level translation.
موصى به
Automotive Sensor / Actuator ECU (Non-Safety)
While the DSPIC30F5015-30I/PT is industrial-grade and not AEC-Q100 qualified, it is widely used in non-safety automotive subsystems such as HVAC blower controllers, seat-position actuators, and body-comfort modules. The 5 V I/O tolerance drives 12 V actuator loads through external FETs, while the CAN module integrates with the vehicle CAN bus at 500 kbaud. Designers targeting AEC-Q100 must migrate to a dsPIC33F family part such as DSPIC33FJ128GP310-I/PT; the same code base typically ports with minimal changes per Microchip's migration guide.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ DSPIC30F5015-30I/PT — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DSPIC30F5011-30I/PT | DSPIC30F5015-20E/PT | DSPIC30F5015T-30I/PT | DSPIC30F4013-30I/P | DSPIC30F4012-30I/ML |
|---|---|---|---|---|---|---|
| Package | 64-pin TQFP (PT) 10x10 mm | 64-pin TQFP (PT) - same | 64-pin TQFP (PT) - same | 64-pin TQFP (PT) - same | 40-pin PDIP - different | 44-pin QFN - different |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Architecture | dsPIC30F, 16-bit modified Harvard | dsPIC30F | dsPIC30F | dsPIC30F | dsPIC30F | dsPIC30F |
| Max CPU Speed / MIPS | 40 MHz / 30 MIPS | 40 MHz / 30 MIPS | 30 MHz / 20 MIPS | 40 MHz / 30 MIPS | 40 MHz / 30 MIPS | 40 MHz / 30 MIPS |
| Program Flash | 66 KB | 66 KB | 66 KB | 66 KB | 48 KB | 48 KB |
| Data RAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| ADC | 12-bit, 16 ch, 200 ksps | 12-bit, 16 ch, 200 ksps | 12-bit, 16 ch, 200 ksps | 12-bit, 16 ch, 200 ksps | 12-bit, 13 ch, 200 ksps | 12-bit, 13 ch, 200 ksps |
| PWM Channels | 4 (motor-control) | 4 | 4 | 4 | 6 | 6 |
| CAN Module | 1 (CAN 2.0B) | 1 | 1 | 1 | 1 | 0 |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C | -40C to +125C (extended) | -40C to +85C | -40C to +85C | -40C to +85C |
| Approx Unit Price (qty 1) | $11.50 | $10.95 | $12.80 | $11.50 | $8.40 | $7.95 |
أبرز الفروقات
- Highest Flash density in the 64-pin dsPIC30F family (مقابلDSPIC30F4013-30I/P)
- Same 30 MIPS throughput with extended-temperature option (مقابلDSPIC30F5015-20E/PT)
- True pin-to-pin silicon identical to the tape-and-reel variant (مقابلDSPIC30F5015T-30I/PT)
- Full peripheral set including CAN in a 64-pin TQFP (مقابلDSPIC30F4012-30I/ML)
ملاحظات التصميم
The DSPIC30F5015-30I/PT integrates a core LDO that derives 2.5 V from the external 3.0 V to 5.5 V AVDD/VDD rail, so only a single supply is needed. Per the datasheet, place one 10 µF bulk tantalum or ceramic + one 100 nF decoupling capacitor on each VDD/AVDD pair (pin 16/64 and pin 57). For motor-control PCBs with switching FET bridges near the DSC, add a ferrite bead on AVDD plus a separate 100 nF cap at the AVSS pin to keep digital switching noise below 50 mV on the analog rail - this preserves ADC accuracy when sampling phase currents.
Keep the OSC1/OSC2 crystal traces (pins 14/15) shorter than 12 mm and surround them with a ground guard ring tied to AVSS. Per Microchip's dsPIC30F Family Reference Manual (DS70046), long crystal traces or missing guard rings cause PLL jitter that shows up as PWM timing jitter and ADC sample-window drift. Place the 22 pF to 33 pF load capacitors as close to the crystal pins as the package allows, and route the MCLR line (pin 17) with a 10 kΩ pull-up to VDD and a 100 nF cap to ground for noise immunity in motor-drive environments.
Estimated: programming/debug on production boards - the PGED1/PGEC1 pair (pins 18/19) shares physical pins with RF4/RF5, and designers sometimes forget to leave them accessible for in-circuit serial programming (ICSP). If those traces are buried under BGA components or routed only as 0.1 mm stubs, field firmware updates become impossible without board rework. Also, the DSPIC30F5015's ADC at 200 ksps requires the input source impedance to be below 200 Ω or sample-and-hold acquisition time must be increased - driving an ADC pin directly from a 10 kΩ potentiometer is a common source of measurement error.
The PWM outputs (PWM1H/L through PWM4H/L on pins 39-46) drive 5 V logic but should never be loaded directly with the gate of a power MOSFET - source 10 Ω to 22 Ω series resistors plus a 1N4148 clamp diode are standard practice to dampen transmission-line ringing on cables longer than 50 mm. For CAN bus (pins 36/37), a 120 Ω termination resistor at each end plus an MCP2551 transceiver (or equivalent) is mandatory; the DSPIC30F5015's CAN peripheral outputs TTL levels that cannot drive the bus directly.
معلومات الامتثال
RoHS and lead-free compliant per Microchip product page. Industrial grade only (-40 to +85 C); for AEC-Q100 automotive, migrate to dsPIC33FJ family.
