EPC8QC100 - 8Mb FPGA Config PROM, 100-PQFP | Altera/Intel
MPN: EPC8QC100 ✗ انتهى عمره الإنتاجيEPC8QC100 نظرة عامة
An FPGA configuration PROM is a specialized non-volatile serial/parallel memory device that stores the bitstream used to program an FPGA at power-up. Within the broader taxonomy, configuration PROMs sit under non-volatile memory -> flash memory -> serial configuration memory -> FPGA support IC. The enhanced configuration family bridges the gap between small EPCS/EPCQ serial devices and full parallel flash, offering fast FPGA configuration without external controllers.
Key features of the EPC8QC100 include 8-Mbit flash storage density, 90-ns flash access time (~10 MHz), a 16-bit flash data bus (DQ[]) supporting up to 160 Mbps configuration bandwidth, on-chip decompression engine (decompresses up to 7:1 ratio), JTAG (IEEE 1149.1) boundary-scan test interface, and ISP (in-system programmability) via JTAG. The device operates from a 3.3V core supply and supports commercial temperature grade (0C to +70C).
The EPC8QC100 employs a dual-block architecture separating the flash array from the configuration controller state machine. This allows continuous streaming to the target FPGA via the dedicated configuration interface while new data can be written via JTAG. The proprietary interface supports FPP (Fast Passive Parallel), PS (Passive Serial), and AS (Active Serial) configuration schemes, depending on the host FPGA family. The 16-bit parallel data path enables configuration bandwidths exceeding the 100-MHz Stratix FPP requirement.
Typical applications include configuration storage for Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K FPGAs in industrial control, telecommunications, networking line cards, and military/aerospace platforms where robust in-field reprogrammability is required.
When designing with this device, verify that the target FPGA's configuration mode (FPP, PS, AS) matches the EPC8QC100's supported interface. Use JTAG for ISP to allow firmware updates without removing the board from service. Decoupling: place 0.1uF ceramic capacitors close to all VCC pins.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
بدائل مباشرة لـ EPC8QC100 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع EPC8QC100 (نفس عامل الشكل والبصمة) — يختلف في Package, Memory Type, Operating Temperature, Memory Size, Interface.
EPC8QC100
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPC16QC100
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPC4QC100
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPC8QI100
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPC16QI100
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPC4QC100N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPC8QC100 الحدود القصوى والخصائص الكهربائية
| نوع الذاكرة | Configuration PROM (Flash-based) |
| حجم الذاكرة | 8 Mbit |
| Flash Access Time | 90 ns (~10 MHz) |
| Configuration Bus Width | 16-bit (DQ[]) |
| Configuration Bandwidth | Up to 160 Mbps |
| Decompression Support | Yes (Altera proprietary) |
| Supported Configuration Modes | FPP, PS, AS (FPGA-dependent) |
| ISP Interface | JTAG (IEEE 1149.1) |
| جهد التغذية | 3.3 V |
| درجة حرارة التشغيل | 0C to +70C (Commercial) |
| العلبة | 100-Pin PQFP (20 x 14 mm) |
| نوع التركيب | Surface Mount |
| Compatible FPGA Families | Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, FLEX 10K |
تكوين أطراف EPC8QC100
| دبوس 1 | DATA0 — Configuration data bit 0 |
| دبوس 2 | DATA1 — Configuration data bit 1 |
| دبوس 3 | DATA2 — Configuration data bit 2 |
| دبوس 4 | DATA3 — Configuration data bit 3 |
| دبوس 5 | DATA4 — Configuration data bit 4 |
| دبوس 6 | DATA5 — Configuration data bit 5 |
| دبوس 7 | DATA6 — Configuration data bit 6 |
| دبوس 8 | DATA7 — Configuration data bit 7 |
| دبوس 9 | DATA8 — Configuration data bit 8 |
| دبوس 10 | DATA9 — Configuration data bit 9 |
| دبوس 11 | DATA10 — Configuration data bit 10 |
| دبوس 12 | DATA11 — Configuration data bit 11 |
| دبوس 13 | DATA12 — Configuration data bit 12 |
| دبوس 14 | DATA13 — Configuration data bit 13 |
| دبوس 15 | DATA14 — Configuration data bit 14 |
| دبوس 16 | DATA15 — Configuration data bit 15 |
| دبوس 17 | VCC — 3.3V supply |
| دبوس 18 | GND — Ground |
| دبوس 19 | nCS — Chip select (active low) |
| دبوس 20 | nOE — Output enable (active low) |
| دبوس 21 | nWE — Write enable (active low) |
| دبوس 22 | CLK — Configuration clock |
| دبوس 23 | MODE — Configuration mode select |
| دبوس 24 | nSTATUS — Status output (active low) |
| دبوس 25 | CONF_DONE — Configuration done signal |
| دبوس 26 | nCONFIG — Configuration control (active low) |
| دبوس 27 | TCK — JTAG test clock |
| دبوس 28 | TMS — JTAG test mode select |
| دبوس 29 | TDI — JTAG test data in |
| دبوس 30 | TDO — JTAG test data out |
| دبوس 31 | VCC — 3.3V supply |
| دبوس 32 | GND — Ground |
| دبوس 33 | RDYnBUSY — Ready/Busy status |
| دبوس 34 | PADD0 — Address/control bit 0 |
| دبوس 35 | PADD1 — Address/control bit 1 |
| دبوس 36 | PADD2 — Address/control bit 2 |
| دبوس 37 | PADD3 — Address/control bit 3 |
| دبوس 38 | PADD4 — Address/control bit 4 |
| دبوس 39 | PADD5 — Address/control bit 5 |
| دبوس 40 | PADD6 — Address/control bit 6 |
| دبوس 41 | PADD7 — Address/control bit 7 |
| دبوس 42 | PADD8 — Address/control bit 8 |
| دبوس 43 | PADD9 — Address/control bit 9 |
| دبوس 44 | PADD10 — Address/control bit 10 |
| دبوس 45 | PADD11 — Address/control bit 11 |
| دبوس 46 | PADD12 — Address/control bit 12 |
| دبوس 47 | PADD13 — Address/control bit 13 |
| دبوس 48 | PADD14 — Address/control bit 14 |
| دبوس 49 | PADD15 — Address/control bit 15 |
| دبوس 50 | VCC — 3.3V supply |
| دبوس 51 | GND — Ground |
| دبوس 52 | PADD16 — Address/control bit 16 |
| دبوس 53 | PADD17 — Address/control bit 17 |
| دبوس 54 | PADD18 — Address/control bit 18 |
| دبوس 55 | PADD19 — Address/control bit 19 |
| دبوس 56 | PADD20 — Address/control bit 20 |
| دبوس 57 | PADD21 — Address/control bit 21 |
| دبوس 58 | PADD22 — Address/control bit 22 |
| دبوس 59 | PADD23 — Address/control bit 23 |
| دبوس 60 | VCC — 3.3V supply |
| دبوس 61 | GND — Ground |
| دبوس 62 | A0 — Address bit 0 |
| دبوس 63 | A1 — Address bit 1 |
| دبوس 64 | A2 — Address bit 2 |
| دبوس 65 | A3 — Address bit 3 |
| دبوس 66 | A4 — Address bit 4 |
| دبوس 67 | A5 — Address bit 5 |
| دبوس 68 | A6 — Address bit 6 |
| دبوس 69 | A7 — Address bit 7 |
| دبوس 70 | A8 — Address bit 8 |
| دبوس 71 | A9 — Address bit 9 |
| دبوس 72 | A10 — Address bit 10 |
| دبوس 73 | A11 — Address bit 11 |
| دبوس 74 | A12 — Address bit 12 |
| دبوس 75 | A13 — Address bit 13 |
| دبوس 76 | A14 — Address bit 14 |
| دبوس 77 | A15 — Address bit 15 |
| دبوس 78 | A16 — Address bit 16 |
| دبوس 79 | A17 — Address bit 17 |
| دبوس 80 | A18 — Address bit 18 |
| دبوس 81 | VCC — 3.3V supply |
| دبوس 82 | GND — Ground |
| دبوس 83 | nBYTE — Byte/word mode select (active low) |
| دبوس 84 | nRESET — Reset (active low) |
| دبوس 85 | WP — Write protect |
| دبوس 86 | NC — Not connected |
| دبوس 87 | NC — Not connected |
| دبوس 88 | NC — Not connected |
| دبوس 89 | NC — Not connected |
| دبوس 90 | NC — Not connected |
| دبوس 91 | VCC — 3.3V supply |
| دبوس 92 | GND — Ground |
| دبوس 93 | NC — Not connected |
| دبوس 94 | NC — Not connected |
| دبوس 95 | NC — Not connected |
| دبوس 96 | NC — Not connected |
| دبوس 97 | NC — Not connected |
| دبوس 98 | NC — Not connected |
| دبوس 99 | VCC — 3.3V supply |
| دبوس 100 | GND — Ground |
التطبيقات النموذجية
EPC8QC100 مناسب لـ 6 التطبيقs: Stratix FPGA Configuration Storage, APEX II / APEX 20K FPGA Configuration, Industrial Control System FPGA Boot, Telecom Line Card Configuration, Military/Aerospace FPGA Systems, Test & Measurement Instrument Configuration.
Stratix FPGA Configuration Storage
The EPC8QC100 stores the Stratix FPGA configuration bitstream in 8 Mbit of flash memory, delivering it to the FPGA via the 16-bit parallel DQ[] bus at up to 160 Mbps. The 90 ns flash access time supports 100-MHz Stratix FPP configuration per the Altera Enhanced Configuration Devices datasheet. Decompression up to 7:1 allows larger uncompressed bitstreams to fit in the 8 Mbit array. ISP via JTAG enables in-field firmware updates without board removal, critical for telecom line cards where downtime is costly.
موصى به
APEX II / APEX 20K FPGA Configuration
For APEX II and APEX 20K FPGAs, the EPC8QC100 provides compressed configuration via FPP or PS modes using the 16-bit DQ[] interface. The 8 Mbit flash density matches typical APEX 20K bitstream sizes (5-7 Mbit uncompressed, fitting comfortably with compression enabled). The 100-PQFP footprint allows direct mounting on legacy APEX 20K boards, supporting both prototyping and production volumes. The JTAG ISP interface enables factory and field programming without external proctors.
موصى به
Industrial Control System FPGA Boot
In industrial automation and process control systems, the EPC8QC100 reliably boots ACEX 1K and FLEX 10K FPGAs at power-up. The commercial 0C to +70C temperature range suits factory-floor environments inside sealed enclosures. The 3.3V supply integrates cleanly with 3.3V digital logic rails common in industrial PLCs. The JTAG ISP interface allows remote firmware updates over industrial Ethernet bridges, supporting IEC 61131-style system modernization without physical board access.
موصى به
Telecom Line Card Configuration
Telecommunications line cards based on Stratix or APEX 20K FPGAs use the EPC8QC100 to store multiple firmware images and configuration revisions. The 8 Mbit flash supports golden-image plus field-upgrade image storage, with JTAG ISP enabling remote bitstream updates via embedded management controllers. The 100-PQFP package provides robust thermal performance for the enclosed, often fanless, NEBS-compliant chassis environment where these cards operate.
موصى به
Military/Aerospace FPGA Systems
Defense and aerospace systems based on radiation-tolerant FLEX 10K or APEX 20K FPGAs benefit from the EPC8QC100's robust configuration delivery and ISP capability. The non-volatile flash storage retains configuration through power cycles and brown-out events. JTAG ISP enables pre-deployment firmware updates and post-deployment configuration changes. Note: industrial temperature variant EPC8QI100 (-40C to +85C) is preferred for harsh-environment applications.
موصى به
Test & Measurement Instrument Configuration
Test and measurement instruments (oscilloscopes, logic analyzers, signal generators) using Stratix or APEX 20K FPGAs for DSP and signal acquisition leverage the EPC8QC100 for reliable configuration storage. The JTAG ISP interface simplifies factory calibration and field firmware updates, allowing manufacturers to ship instruments with upgradeable feature sets. The 16-bit parallel configuration bus minimizes FPGA boot time, reducing instrument startup delays in production test environments.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ EPC8QC100 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | EPC16QC100 | EPC4QC100 | EPC8QI100 | EPC16QI100 |
|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | 100-PQFP (20x14) | 100-PQFP (20x14) - same | 100-PQFP (20x14) - same | 100-PQFP (20x14) - same | 100-PQFP (20x14) - same |
| Flash Memory Size | 8 Mbit | 16 Mbit | 4 Mbit | 8 Mbit | 16 Mbit |
| Configuration Bus Width | 16-bit | 16-bit | 16-bit | 16-bit | 16-bit |
| Operating Temperature | 0C to +70C (Commercial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| JTAG ISP | Yes | Yes | Yes | Yes | Yes |
| Supply Voltage | 3.3V | 3.3V | 3.3V | 3.3V | 3.3V |
| Compatible FPGAs | Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, FLEX 10K | Same families | Same families | Same families | Same families |
أبرز الفروقات
- Doubles storage capacity with same footprint (مقابلEPC4QC100)
- Industrial temperature grade option (مقابلEPC8QC100 (commercial))
- Combined capacity and industrial temp (مقابلEPC8QC100 base part)
ملاحظات التصميم
The EPC8QC100 operates from a single 3.3V supply (3.0-3.6V range per Altera datasheet). Decoupling: place a 0.1uF ceramic capacitor close to each VCC pin with a low-impedance ground return to handle flash programming current transients. During JTAG ISP, peak current can spike during sector erase and program operations - bulk decoupling (4.7uF to 10uF tantalum or ceramic) near the device is recommended.
Do not confuse EPC8QC100 (parallel enhanced configuration PROM) with EPCS-series (serial configuration memory) or EPCQ-series (active serial). The configuration protocols are not interchangeable: EPC8QC100 uses FPP/PS parallel mode with 16-bit DQ[] bus, while EPCS/EPCQ use single-wire AS mode. Connecting an EPC8QC100 to a Cyclone/Stratix AS configuration pinout will not work. Always verify the target FPGA's configuration mode matches the PROM's interface.
Route the 16-bit DQ[] configuration bus with matched trace lengths to the target FPGA configuration pins to avoid setup/hold violations at high FPP clock rates. Place the EPC8QC100 close to the FPGA to minimize bus loading. JTAG signals (TCK, TMS, TDI, TDO) should be routed with consideration for the daisy-chain topology - include proper pull-ups on TMS and TDI per IEEE 1149.1 recommendations.
معلومات الامتثال
RoHS and REACH compliance status not verified in provided data - marked [DATA_NEEDED]. AEC-Q100 not applicable as this is a memory/configuration device, not an automotive-grade IC. The device is mature/approaching end-of-life.
