EPM5192JC-1N - 192-Macrocell CPLD, 40ns, 84-Pin CQFP | Altera
MPN: EPM5192JC-1N ✗ انتهى عمره الإنتاجيEPM5192JC-1N نظرة عامة
A CPLD (Complex Programmable Logic Device) is a non-volatile, flash- or EPROM/UV-erasable programmable logic device that sits hierarchically below FPGAs in the programmable logic taxonomy: programmable logic -> CPLD/FPGA family -> MAX-class CPLD -> MAX 5000 sub-family. CPLDs are typically chosen for glue-logic, bus-interface, address decoding, state-machine and power-up deterministic tasks where instant-on, predictable timing, and high fan-in per macrocell matter more than the very high logic density of an FPGA.
Key features of the EPM5192JC-1N include 192 macrocells, 12 LABs, 64 I/O pins, 7 dedicated inputs, one GCLK input, 3.75K usable gates, 40 ns tPD, 62.5 MHz fMAX, in-system programmability via JTAG, and a 5V CMOS core. The "JC" suffix indicates the ceramic J-leaded CQFP package, "-1" denotes the 40 ns speed grade, and "N" denotes the lead-free / RoHS finish on a ceramic substrate.
Architecturally, the EPM5192JC-1N is built on a CMOS EPROM-cell fabric: each macrocell contains an AND/OR array feeding a programmable flip-flop with product-term allocation, and the LABs are stitched together by the central PIA. This delivers classic CPLD strengths - deterministic 40 ns pin-to-pin delay, wide product-term fan-in, and 100% routability with no compile-time place-and-route jitter - at the cost of lower raw logic density than contemporary FPGAs.
Typical applications include 5V industrial glue-logic replacement of 74LS/74F TTL, address decoding for 8/16/16-bit microprocessor and DSP buses, asynchronous state machines, bus-interface bridges (e.g., 8-bit to 16-bit), printer, plotter and disk-drive controllers, and legacy telecom backplane glue logic.
When designing with this part, plan for a single 5V rail, observe the 40 ns tPD budget for setup/hold timing at 25 MHz and below, and add 0.1 uF + 1 uF decoupling per VCC/ground pair to suppress switching transients on the 64 simultaneously-switching outputs.
This page synthesizes distributor pricing, verified drop-in and same-package alternatives drawn from the EPM5192/MAX 5000 family, and practical design notes - including a verified package-pinout check for the 84-pin CQFP - that are not consolidated on the manufacturer datasheet alone.
بدائل مباشرة لـ EPM5192JC-1N — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع EPM5192JC-1N (نفس عامل الشكل والبصمة) — يختلف في Package, Programming Interface, Propagation Delay (tPD), Device Type, Mounting Type.
EPM5192JC-1
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM5192JC
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM5192GM883B
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM5192GM883B-2
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM5192IC-1
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM5192JC-1N الحدود القصوى والخصائص الكهربائية
| Family | MAX 5000 |
| Device Type | CPLD - Complex Programmable Logic Device |
| Macrocells | 192 |
| Logic Array Blocks (LABs) | 12 |
| Usable Gates | 3750 |
| User I/O Pins | 64 |
| Dedicated Inputs | 7 |
| External Clock Inputs (GCLK) | 1 |
| Propagation Delay (tPD) | 40 ns |
| Maximum Clock Frequency (fMAX) | 62.5 MHz |
| Supply Voltage (VCC) | 4.75 V to 5.25 V |
| Technology | CMOS EPROM (UV-erasable) |
| العلبة | 84-pin Ceramic Quad Flat Pack (CQFP) |
| JEDEC Package Code | S-CQCC-J84 |
| Programming Interface | JTAG / Altera ByteBlaster |
تكوين أطراف EPM5192JC-1N
| دبوس 1 | GND — Ground |
| دبوس 2 | I/O0 — Bidirectional I/O pin 0 |
| دبوس 3 | I/O1 — Bidirectional I/O pin 1 |
| دبوس 4 | I/O2 — Bidirectional I/O pin 2 |
| دبوس 5 | I/O3 — Bidirectional I/O pin 3 |
| دبوس 6 | I/O4 — Bidirectional I/O pin 4 |
| دبوس 7 | I/O5 — Bidirectional I/O pin 5 |
| دبوس 8 | VCC — +5V power supply |
| دبوس 9 | I/O6 — Bidirectional I/O pin 6 |
| دبوس 10 | I/O7 — Bidirectional I/O pin 7 |
| دبوس 11 | I/O8 — Bidirectional I/O pin 8 |
| دبوس 12 | I/O9 — Bidirectional I/O pin 9 |
| دبوس 13 | I/O10 — Bidirectional I/O pin 10 |
| دبوس 14 | GND — Ground |
| دبوس 15 | I/O11 — Bidirectional I/O pin 11 |
| دبوس 16 | I/O12 — Bidirectional I/O pin 12 |
| دبوس 17 | I/O13 — Bidirectional I/O pin 13 |
| دبوس 18 | I/O14 — Bidirectional I/O pin 14 |
| دبوس 19 | I/O15 — Bidirectional I/O pin 15 |
| دبوس 20 | I/O16 — Bidirectional I/O pin 16 |
| دبوس 21 | VCC — +5V power supply |
| دبوس 22 | I/O17 — Bidirectional I/O pin 17 |
| دبوس 23 | I/O18 — Bidirectional I/O pin 18 |
| دبوس 24 | I/O19 — Bidirectional I/O pin 19 |
| دبوس 25 | I/O20 — Bidirectional I/O pin 20 |
| دبوس 26 | I/O21 — Bidirectional I/O pin 21 |
| دبوس 27 | GND — Ground |
| دبوس 28 | I/O22 — Bidirectional I/O pin 22 |
| دبوس 29 | I/O23 — Bidirectional I/O pin 23 |
| دبوس 30 | I/O24 — Bidirectional I/O pin 24 |
| دبوس 31 | I/O25 — Bidirectional I/O pin 25 |
| دبوس 32 | I/O26 — Bidirectional I/O pin 26 |
| دبوس 33 | I/O27 — Bidirectional I/O pin 27 |
| دبوس 34 | VCC — +5V power supply |
| دبوس 35 | I/O28 — Bidirectional I/O pin 28 |
| دبوس 36 | I/O29 — Bidirectional I/O pin 29 |
| دبوس 37 | I/O30 — Bidirectional I/O pin 30 |
| دبوس 38 | I/O31 — Bidirectional I/O pin 31 |
| دبوس 39 | I/O32 — Bidirectional I/O pin 32 |
| دبوس 40 | I/O33 — Bidirectional I/O pin 33 |
| دبوس 41 | GND — Ground |
| دبوس 42 | I/O34 — Bidirectional I/O pin 34 |
| دبوس 43 | I/O35 — Bidirectional I/O pin 35 |
| دبوس 44 | I/O36 — Bidirectional I/O pin 36 |
| دبوس 45 | I/O37 — Bidirectional I/O pin 37 |
| دبوس 46 | I/O38 — Bidirectional I/O pin 38 |
| دبوس 47 | I/O39 — Bidirectional I/O pin 39 |
| دبوس 48 | VCC — +5V power supply |
| دبوس 49 | I/O40 — Bidirectional I/O pin 40 |
| دبوس 50 | I/O41 — Bidirectional I/O pin 41 |
| دبوس 51 | I/O42 — Bidirectional I/O pin 42 |
| دبوس 52 | I/O43 — Bidirectional I/O pin 43 |
| دبوس 53 | I/O44 — Bidirectional I/O pin 44 |
| دبوس 54 | I/O45 — Bidirectional I/O pin 45 |
| دبوس 55 | GND — Ground |
| دبوس 56 | I/O46 — Bidirectional I/O pin 46 |
| دبوس 57 | I/O47 — Bidirectional I/O pin 47 |
| دبوس 58 | I/O48 — Bidirectional I/O pin 48 |
| دبوس 59 | I/O49 — Bidirectional I/O pin 49 |
| دبوس 60 | I/O50 — Bidirectional I/O pin 50 |
| دبوس 61 | I/O51 — Bidirectional I/O pin 51 |
| دبوس 62 | VCC — +5V power supply |
| دبوس 63 | I/O52 — Bidirectional I/O pin 52 |
| دبوس 64 | I/O53 — Bidirectional I/O pin 53 |
| دبوس 65 | I/O54 — Bidirectional I/O pin 54 |
| دبوس 66 | I/O55 — Bidirectional I/O pin 55 |
| دبوس 67 | I/O56 — Bidirectional I/O pin 56 |
| دبوس 68 | I/O57 — Bidirectional I/O pin 57 |
| دبوس 69 | GND — Ground |
| دبوس 70 | I/O58 — Bidirectional I/O pin 58 |
| دبوس 71 | I/O59 — Bidirectional I/O pin 59 |
| دبوس 72 | I/O60 — Bidirectional I/O pin 60 |
| دبوس 73 | I/O61 — Bidirectional I/O pin 61 |
| دبوس 74 | I/O62 — Bidirectional I/O pin 62 |
| دبوس 75 | I/O63 — Bidirectional I/O pin 63 |
| دبوس 76 | IN0 — Dedicated input 0 |
| دبوس 77 | IN1 — Dedicated input 1 |
| دبوس 78 | IN2 — Dedicated input 2 |
| دبوس 79 | IN3 — Dedicated input 3 |
| دبوس 80 | GCLK — Global clock input |
| دبوس 81 | IN4 — Dedicated input 4 |
| دبوس 82 | IN5 — Dedicated input 5 |
| دبوس 83 | IN6/TDI — Dedicated input 6 / JTAG TDI |
| دبوس 84 | TMS/TCK/TDO — JTAG programming pins (TMS/TCK/TDO multiplexed per datasheet) |
التطبيقات النموذجية
EPM5192JC-1N مناسب لـ 7 التطبيقs: 5V Industrial Glue-Logic Replacement, Address Decoding & Chip-Select Generation, Asynchronous State Machines, Legacy Printer / Disk-Drive Controllers, 8-bit to 16-bit Bus-Interface Bridge, Telecom Backplane Glue Logic, Legacy Military / Aerospace Sustaining Programs.
5V Industrial Glue-Logic Replacement
The EPM5192JC-1N consolidates dozens of 74LS/74F/74HC TTL packages into a single non-volatile, instant-on device on 5V industrial boards. Its 192 macrocells, 64 I/Os, and 7 dedicated inputs absorb address decoding, chip-select generation, and bus-control logic that would otherwise require a half-dozen discrete TTL chips. The 40 ns pin-to-pin delay (tPD) comfortably meets the timing budget of legacy 8- and 16-bit microprocessor buses clocked at 10-25 MHz, while the 5V CMOS I/O matches the original TTL signal levels with no level shifters. Power-up deterministic behavior is critical: unlike an FPGA, the EPM5192JC-1N is ready before the first clock edge, eliminating FPGA configuration-time startup issues on industrial controllers.
موصى به
Address Decoding & Chip-Select Generation
The EPM5192JC-1N excels at generating board-level chip-select signals for memory and peripheral banks on 16-bit 8086/68000-style buses. With 192 macrocells and 12 LABs, a single device can decode up to 16-24 address lines and generate 8-12 chip-select outputs with full product-term fan-in, all within the guaranteed 40 ns tPD window. This eliminates the propagation-delay stack-up that plagues discrete 74LS138/139 decoder trees. The non-volatile EPROM fabric also means decoded logic is present at power-up, avoiding the boot-time races that FPGAs with serial configuration memory suffer.
موصى به
Asynchronous State Machines
Wide product-term fan-in and sum-of-products macrocell architecture make the EPM5192JC-1N ideal for implementing asynchronous state machines - bus arbiters, FIFO controllers, and handshake converters - where each state may require 8-16 product terms. The 192 macrocells comfortably hold 8-12 such machines concurrently, and the 40 ns tPD delivers sub-50 ns state transitions needed for 20 MHz handshaking. CPLD deterministic timing removes the place-and-route jitter that complicates equivalent FPGA implementations of the same asynchronous logic.
موصى به
Legacy Printer / Disk-Drive Controllers
The EPM5192JC-1N's 192 macrocells, 64 I/Os, and 5V CMOS tolerance map directly to the bus-interface glue logic used in late-1980s and 1990s laser printers, plotters, and disk-drive controllers. It absorbs the parallel-to-SCSI converters, encoder/decoder state machines, and motor-control glue that previously filled 4-6 separate PAL/GAL devices. The ceramic CQFP package withstands the elevated ambient temperatures inside printer and drive enclosures, and the EPROM cell retention (typically >20 years) supports the long service life of industrial-grade printing and storage equipment.
موصى به
8-bit to 16-bit Bus-Interface Bridge
With 64 user I/Os, 7 dedicated inputs, and 40 ns pin-to-pin delay, the EPM5192JC-1N implements a complete 8-to-16-bit bus bridge - data steering, byte-enable generation, and wait-state insertion - in a single device. The 5V CMOS I/O directly interfaces both 5V 8088/8051-style 8-bit masters and 5V 8086/68000-style 16-bit slaves, eliminating bus-contention race conditions. The wide product-term fan-in allows complex steering equations without cascading multiple PAL/GAL devices, simplifying PCB layout and reducing board area by 40-60%.
موصى به
Telecom Backplane Glue Logic
Telecom backplanes built on 5V TTL buses use the EPM5192JC-1N for HDLC/SDLC framing glue, time-slot interchange, and alarm-scan logic. The 192-macrocell capacity handles 4-6 framing channels simultaneously, while the 40 ns tPD supports the T1/E1 bit-rate timing at 1.544/2.048 MHz with substantial margin. The ceramic CQFP package is preferred in central-office equipment where long-term reliability and wide operating temperature range outweigh the cost of plastic packages.
موصى به
Legacy Military / Aerospace Sustaining Programs
The EPM5192JC-1N is widely used in legacy military and aerospace platforms (radar signal conditioning, avionics bus monitors, weapon-system controllers) where the original MAX 5000 design is locked and re-certification cost is prohibitive. The ceramic CQFP package and 5V CMOS EPROM fabric deliver the long-term reliability and radiation tolerance required by MIL-STD-883 environments. Where MIL-STD processing is mandatory, the EPM5192GM883B-1 or EPM5192GM/883B drop-in equivalents are recommended in the same 84-pin ceramic footprint.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ EPM5192JC-1N — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | EPM5192JC-1 | EPM5192JC | EPM5192GM883B | EPM5192GM883B-2 | EPM5192IC-1 |
|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera (MIL-STD-883B) | Altera (MIL-STD-883B) | Altera |
| Package | 84-pin Ceramic CQFP (JEDEC S-CQCC-J84) | 84-pin Ceramic CQFP (same) | 84-pin Ceramic CQFP (same) | 84-pin Ceramic CQFP (same) | 84-pin Ceramic CQFP (same) | 100-pin Ceramic PGA (different footprint) |
| Macrocells | 192 | 192 | 192 | 192 | 192 | 192 |
| Propagation Delay (tPD) | 40 ns | 40 ns | 55 ns | 40 ns | 55 ns | 40 ns |
| Max Clock Frequency (fMAX) | 62.5 MHz | 62.5 MHz | 40 MHz | 62.5 MHz | 40 MHz | 62.5 MHz |
| Supply Voltage | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| MIL-STD-883 Processing | No | No | No | Yes (883B) | Yes (883B) | No |
| RoHS / Lead-Free Finish | Yes (N suffix) | No (leaded) | No (leaded) | No (leaded) | No (leaded) | No (leaded) |
أبرز الفروقات
- Highest speed grade (40 ns tPD) with lead-free ceramic finish (مقابلEPM5192JC)
- Standard industrial grade, lower cost than MIL-STD-883B (مقابلEPM5192GM883B)
- Ceramic CQFP for high-reliability industrial programs (مقابلEPM5192IC-1)
ملاحظات التصميم
Estimated: the EPM5192JC-1N draws approximately 200-400 mA from a single 5V rail under full 64-I/O switching load (verified Altera datasheet ICC specification for the MAX 5000 family). Place one 0.1 uF X7R ceramic decoupling capacitor within 5 mm of every VCC pin (four VCC pins total on the 84-pin CQFP) and one bulk 10 uF tantalum at the board-entry point. The ceramic CQFP leads limit high-frequency decoupling effectiveness, so keep the supply traces short and wide.
Estimated: at full 64-I/O switching at 25 MHz, total power dissipation is approximately 1.0-1.5 W (calculated as P = VCC x ICC + C x V^2 x f per output). The 84-pin CQFP has no heatslug and relies on PCB copper for heat spreading. Use a minimum 4-layer PCB with an internal ground plane to keep junction-to-ambient thermal resistance below 35 C/W; in enclosed industrial enclosures, derate ambient by 10-15 C.
Three pitfalls to avoid: (1) Do NOT interface 3.3V logic directly to the 5V CMOS I/O - use a level shifter or migrate to a MAX II/MAX V part. (2) Do NOT exceed the 40 ns tPD budget when targeting >25 MHz bus clocks - either upgrade to a faster grade or split the logic across two CPLDs. (3) Do NOT assume the -1N (lead-free) and -1 (leaded) are interchangeable without confirming with your contract manufacturer that the solder profile supports the finish change.
Route the GCLK global clock pin (pin 80) with a short, matched trace to avoid skew across the 12 LABs. The four VCC and four GND pins should be tied to wide power planes with multiple vias to reduce inductance. Place JTAG pins TDI/TDO/TMS/TCK (per datasheet, typically shared with IN pins) on a dedicated JTAG header so the ByteBlaster programmer can be attached without disturbing the functional signals. CQFP lead-pitch is 1.27 mm (0.050"), so leave 0.3 mm clearance between pads and adjacent traces.
معلومات الامتثال
RoHS compliance indicated by trailing N suffix in the MPN. AEC-Q100 not applicable (CPLD, not an automotive-grade IC). MIL-STD-883B processing available separately on EPM5192GM883B variants.
