ICS512MIT - 160MHz PLL Clock Generator | Renesas Electronics
MPN: ICS512MIT ✗ انتهى عمره الإنتاجيICS512MIT نظرة عامة
A PLL clock generator is a timing IC that multiplies or synthesizes a clock frequency while providing a stable reference for digital and analog systems. The ICS512 belongs to the clock and timing hierarchy within integrated circuits, where it functions as a frequency multiplier and clock source. Its low-cost oscillator architecture is intended to replace conventional crystal oscillators in many electronic systems.
Key features include a maximum operating frequency of 160MHz, one clock or crystal input, one CMOS output, and PLL operation with bypass capability. The input-to-output ratio listed for the device is 1:2, allowing a lower-frequency reference to generate a higher-frequency clock. The operating supply range is 3V to 5V, and the specified operating temperature range is -40°C to +85°C.
The PLL-based architecture uses a standard fundamental-mode crystal to establish a stable reference, then multiplies that reference to generate the requested output clock. Bypass mode provides a practical path for clock distribution or test configurations. The CMOS output is suited to digital logic, communication equipment, consumer electronics, and embedded systems requiring a centralized clock source.
Typical applications include digital controller boards, communication modules, industrial control equipment, test and measurement systems, and embedded products that require a multiplied clock or reference signal. The 8-SOIC surface-mount package supports compact board layouts while keeping assembly compatible with conventional SOIC-8 footprint practices.
Designers should confirm the crystal frequency, PLL ratio, output waveform, load capacitance, and bypass configuration against the manufacturer application guidance. Decoupling capacitors should be placed close to the supply and ground pins, and clock traces should be routed with controlled impedance and minimized loading.
This product page combines the manufacturer specifications, package information, lifecycle status, practical design notes, and sourcing guidance for engineers evaluating the ICS512MIT as an obsolete clock-generation component or replacement candidate.
بدائل مباشرة لـ ICS512MIT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلICS512MIT المواصفات
| Product Type | PLL clock generator |
| Maximum Frequency | 160 MHz |
| Number of Circuits | 1 |
| نوع الخرج | CMOS |
| Input Type | Clock or crystal |
| PLL | Yes, with bypass |
| Input-to-Output Ratio | 1:2 |
| Supply Voltage Range | 3 V to 5 V |
| نطاق درجة حرارة التشغيل | -40°C to +85°C |
| العلبة | 8-SOIC, 0.154 inch / 3.90mm width |
| نوع التركيب | Surface mount |
| الفئة | Clock generators, PLLs, frequency synthesizers |
| Output Frequency | 160 MHz maximum |
| عدد المخارج | 1 |
| Manufacturer | Renesas Electronics Corporation |
| Original Manufacturer | Integrated Device Technology / Integrated Circuit Systems |
| حالة دورة الحياة | Obsolete (EOL) |
دليل تكوين أطراف ICS512MIT 8-soic, 0.154 inch / 3.90mm width
تكوين الأطراف لـ ICS512MIT (حزمة 8-soic, 0.154 inch / 3.90mm width). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ICS512MIT.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
ICS512MIT مناسب لـ 6 التطبيقs: Digital Controller Clocking, Communication Module Clock Reference, Industrial Control Equipment, Test and Measurement Systems, Embedded Consumer Products, Clock Distribution and Test Modes.
Digital Controller Clocking
The ICS512MIT fits legacy digital controller designs that need a multiplied clock generated from a lower-frequency crystal or reference. Its PLL multiplier provides a maximum output frequency of 160 MHz, while the 1:2 input-to-output ratio allows a lower-frequency reference to be raised to the required operating rate. The single CMOS output is appropriate for a central controller, processor, or programmable logic device in older 3.3 V or 5 V equipment. Designers should verify the required crystal frequency and ensure that the PLL configuration produces the exact clock expected by the downstream digital circuit.
موصى به
Communication Module Clock Reference
ICS512MIT can serve as the clock-generation element in a legacy communication module requiring a stable, high-frequency reference from a crystal source. The PLL-based architecture is intended to generate a high-quality output clock and reference clock, while the CMOS output can feed a controller, transceiver, or digital signal-processing chain. Its 160 MHz ceiling supports timing requirements commonly found in older embedded communication equipment. PCB layout should keep the crystal path short and isolate the clock output from noisy switching nodes.
موصى به
Industrial Control Equipment
The ICS512MIT is applicable to industrial control equipment designed around older clock architectures, with its specified -40°C to +85°C operating range covering many industrial environments. A single CMOS clock output can synchronize control logic, data acquisition electronics, or communications hardware. The 8-SOIC package is straightforward to accommodate in conventional surface-mount assemblies. Because the device is obsolete, engineers should confirm availability and evaluate an active replacement before committing to a new production design.
موصى به
Test and Measurement Systems
ICS512MIT can provide a multiplied clock or reference signal in legacy test and measurement systems that use a crystal-based timing architecture. Its PLL capability supports clock generation up to 160 MHz, and the 1:2 ratio can simplify designs using a fundamental reference frequency. The CMOS output is compatible with common digital timing and control blocks. Measurement accuracy still depends on the reference source, loop filtering, layout quality, and downstream clock requirements, so engineers should validate jitter and edge performance in the complete circuit.
موصى به
Embedded Consumer Products
ICS512MIT is appropriate for maintaining older embedded consumer products that already use an 8-SOIC PLL clock generator. Its 3 V to 5 V operating range supports common embedded supply rails, and its single CMOS output can feed a controller or peripheral requiring a multiplied clock. The device provides a familiar architecture for servicing and reproducing older equipment, but new product development should favor an active clock generator with confirmed availability, lifecycle support, and equivalent timing performance. Do not assume that an 8-SOIC replacement is pin-compatible without checking the manufacturer’s pin table.
موصى به
Clock Distribution and Test Modes
The ICS512MIT’s PLL bypass capability makes it useful in legacy systems that need to switch between an internally multiplied clock and an external or reference clock path. The bypass function can support board test, clock-source selection, or diagnostic configurations where a direct reference is useful. Its one-output architecture limits scalability compared with multi-output clock buffers, so larger designs may need an additional distribution stage. Layout should keep the bypass source, crystal path, and output trace controlled to prevent timing degradation.
موصى به
بيانات مرجعية هندسية لـ ICS512MIT — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Brand | Renesas Electronics |
| Package | 8-SOIC |
| Maximum Frequency | 160 MHz |
| Number of Circuits | 1 |
| Output Type | CMOS |
| Input Type | Clock or crystal |
| PLL | Yes, with bypass |
| Input-to-Output Ratio | 1:2 |
| Supply Voltage Range | 3 V to 5 V |
| Operating Temperature | -40°C to +85°C |
أبرز الفروقات
- Single CMOS clock output with PLL bypass support (مقابلICS512MIT)
- Legacy-compatible 8-SOIC footprint (مقابلICS512MIT)
- Broad 3 V to 5 V operating range (مقابلICS512MIT)
ملاحظات التصميم
Keep the crystal, reference-clock input, PLL support components, and ICS512MIT on the same side of the PCB where practical. Place the decoupling capacitor at the device supply and ground pins rather than at the connector or power-source entry point. This minimizes loop area and helps prevent supply noise from coupling into the clock output.
Route the clock output as a short, controlled-impedance trace and avoid sharing it with long switching nets. Keep the crystal path away from high-current switches, inductors, and fast digital edges. When bypassing the PLL, route the selected clock source cleanly and confirm that the bypass configuration in the Renesas 512 datasheet matches the system test mode.
Do not select a replacement based only on the 8-SOIC package or the 160 MHz headline frequency. Verify pin numbers, crystal connection, PLL ratio, bypass behavior, supply limits, output waveform, and operating-temperature requirements against the manufacturer datasheet. ICS512MIT is obsolete, so any substitute must also be checked for current lifecycle status and production continuity.
معلومات الامتثال
The available product information does not establish the compliance status of ICS512MIT.