Renesas Electronics

ICS525R-04 - 200MHz PECL Clock Generator | Renesas

MPN: ICS525R-04 ✓ نشط
4.5 V to 5.5 V Vdss 28-pin SSOP, 0.150 inch pitch Package 200 MHz Speed
الحد الأدنى للطلب: 1 |

ICS525R-04 نظرة عامة

Renesas ICS525R-04 is a user-configurable clock generator that produces a high-quality differential PECL clock output up to 200 MHz. The device accepts a CMOS or crystal reference input, includes a PLL, and is packaged in a 28-pin SSOP. Its operating supply voltage is 4.5 V to 5.5 V.

A clock generator is an integrated timing component that creates, conditions, and distributes a stable frequency reference through a system. The OSCaR family combines a phase-locked loop with selectable configuration pins, placing clock generation in the Clock & Timing IC category within the broader semiconductor and power-management ecosystem. Unlike a simple crystal oscillator, this architecture can support user-selectable output relationships and provide PECL-compatible differential outputs for high-speed digital circuitry.

The ICS525R-04 supports a maximum operating frequency of 200 MHz and uses a PECL output interface. Configuration can be established through hardware-select pins rather than firmware or a device programmer, making the part useful where deterministic setup and minimal firmware support are priorities. The 4.5 V to 5.5 V supply range and SSOP-28 surface-mount package support established 5 V digital clocking systems.

Internally, the OSCaR architecture uses a PLL to multiply or divide a crystal or external clock reference and generate the required output frequency. A PLL-based approach provides programmable frequency relationships while retaining a stable external reference. Differential PECL outputs are suited to short-reach, point-to-point interconnects where source-synchronous clocking, serializer/deserializer interfaces, or high-speed digital logic require low-skew clock distribution.

Typical uses include telecommunications line cards, network-interface clock trees, high-speed serial links, test-and-measurement equipment, and industrial control systems. The same clock-generation approach can also support digital signal processors, FPGA clock planes, and communications processors when the system needs a locally generated PECL reference rather than a panel-distributed clock.

When laying out the circuit, place the crystal and input decoupling close to the device and route differential outputs as a tightly matched pair with uninterrupted reference planes. The 28-pin SSOP footprint requires careful fanout because its narrow lead pitch can constrain escape routing on multilayer boards. Verify configuration-pin states during power-up and validate output frequency and duty-cycle behavior across the complete operating temperature range.

This product record combines the oscillator function, principal electrical characteristics, package details, sourcing information, and practical implementation guidance in one engineering-focused reference. It also distinguishes verified device attributes from parameters that require confirmation from the manufacturer datasheet, helping designers move from component selection to a complete clock-tree design with fewer documentation gaps.

بدائل مباشرة لـ ICS525R-04 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

ICS525R-01

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 28-pin SSOP
Nominal configuration code changes from 04 to 01; the maximum-frequency rating remains 200 MHz, a 0% difference, but the output-ratio implementation may differ.

📋 بديل مرجعي (غير موجود في الكتالوج)

ICS525R-02

✅ بديل مباشر
Renesas Electronics
📦 28-pin SSOP
Clock generator and fanout distribution IC · OSCaR user-configurable clock · 250 MHz · 1 · Yes, with bypass · Clock or crystal · CMOS · 28-pin SSOP

تواصل لمعرفة السعر

عرض ورقة البيانات ←

ICS525R-03

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 28-pin SSOP
Nominal configuration code changes from 04 to 03; the maximum-frequency rating remains 200 MHz, a 0% difference, but the clock-ratio implementation may differ.

📋 بديل مرجعي (غير موجود في الكتالوج)

ICS525R-06

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 28-pin SSOP
Nominal configuration code changes from 04 to 06; the maximum-frequency rating remains 200 MHz, a 0% difference, but the selectable output relationship must be verified.

📋 بديل مرجعي (غير موجود في الكتالوج)

ICS525R-08

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 28-pin SSOP
Nominal configuration code changes from 04 to 08; the maximum-frequency rating remains 200 MHz, a 0% difference, while frequency-ratio behavior requires confirmation.

📋 بديل مرجعي (غير موجود في الكتالوج)

ICS525R-04 المواصفات

Device Type Clock Generator
Product Family OSCaR
Maximum Frequency 200 MHz
Number of Circuits 1
PLL Yes
Input Interface CMOS or Crystal
Output Interface Differential PECL
تكوين الخرج User Configurable
Supply Voltage Range 4.5 V to 5.5 V
العلبة 28-pin SSOP, 0.150 inch pitch
نوع التركيب Surface Mount
Package Outline Reference MO-153
حالة RoHS Compliant
Configuration Method Hardware select pins
Programming Requirement None

دليل تكوين أطراف ICS525R-04 mo-153

تكوين الأطراف لـ ICS525R-04 (حزمة mo-153). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة mo-153 لـ ICS525R-04

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ICS525R-04.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ICS525R-04 مناسب لـ 6 التطبيقs: Telecommunications Line-Card Clocking, FPGA Source-Synchronous Clocking, High-Speed Serial Link Clock Reference, Industrial Control and Instrumentation, Test and Measurement Clock Trees, Network Interface and Processor Timing.

🌐

Telecommunications Line-Card Clocking

The ICS525R-04 fits telecommunications line-card clock trees that require a locally generated differential PECL clock. Its PLL-based architecture can operate from a crystal or CMOS reference and supports user configuration through hardware pins, eliminating firmware setup for the clock device. The 200 MHz maximum frequency provides useful headroom for high-speed line-card logic, while the 4.5 V to 5.5 V operating range aligns with conventional 5 V backplane equipment. Differential PECL outputs are particularly useful when the clock must traverse a controlled, short-reach connection between clock-generation and interface circuitry.

🖥️

FPGA Source-Synchronous Clocking

The ICS525R-04 is suitable for generating a differential reference for FPGA source-synchronous interfaces when the required clock does not exceed 200 MHz. Hardware-selectable configuration allows the clock function to be established independently of FPGA firmware, which can simplify boot sequencing and board bring-up. The PLL accepts a crystal or CMOS reference so the design can use either an onboard resonator or a shared reference. Designers should verify the FPGA's input threshold, clock-input architecture, and maximum operating frequency before connecting the PECL output.

🌐

High-Speed Serial Link Clock Reference

The ICS525R-04 can provide a stable differential PECL reference for high-speed serial links that require coordinated transmit and receive clocking. Its 200 MHz ceiling supports demanding parallel-clock or divided-clock architectures, while the PLL provides a controllable relationship between the external reference and generated outputs. Because PECL links are sensitive to routing and termination, the implementation should use matched differential routing, continuous reference planes, and the termination network shown in the manufacturer application circuit.

🏭

Industrial Control and Instrumentation

The ICS525R-04 supports industrial control and test-instrumentation subsystems that need deterministic timing without a software-programmed clock source. Its hardware configuration method is useful in equipment where startup behavior must be controlled by straps, GPIO defaults, or other fixed hardware. The 28-pin SSOP package supports compact, surface-mounted designs, and the 4.5 V to 5.5 V supply range fits common 5 V analog and digital subsystems. Engineers should account for the narrow package pitch and route clock traces away from switching-power and high-current return paths.

🔧

Test and Measurement Clock Trees

The ICS525R-04 is appropriate for test and measurement equipment that distributes a local high-speed clock to acquisition, conversion, or digital processing sections. A 200 MHz differential PECL clock can feed compatible instrumentation blocks when clean edge rates and deterministic phase relationships are important. The device can be driven from a crystal or CMOS source, allowing reference selection according to calibration requirements. Production validation should cover frequency accuracy, duty-cycle distortion, output amplitude, and jitter using the same loading and termination intended for the final instrument.

🌐

Network Interface and Processor Timing

The ICS525R-04 can support processor and network-interface timing islands that require a local clock derived from a common reference. Its PLL architecture permits a crystal or CMOS input to drive a controlled differential output, and its user-selectable configuration avoids tying clock setup to software initialization. The 200 MHz maximum frequency is relevant to interfaces operating at one-half, one-third, or another programmed ratio of the reference, subject to the device configuration table. Integration requires checking the downstream device's PECL input limits and sequencing requirements against the power ramp.

ملخص المنتجات الموصى بها

ICS525R-02 Renesas Electronics يُستخدم في: Telecommunications Line-Card Clocking, FPGA Source-Synchronous Clocking, Industrial Control and Instrumentation ICS525R-01 Same-family user-configurable PECL clock يُستخدم في: Telecommunications Line-Card Clocking, High-Speed Serial Link Clock Reference, Test and Measurement Clock Trees ICS525R-03 OSCaR-family clock option for FPGA interface timing يُستخدم في: FPGA Source-Synchronous Clocking, Test and Measurement Clock Trees ICS525R-06 Same-family clock generator with an alternate configuration code يُستخدم في: High-Speed Serial Link Clock Reference, Network Interface and Processor Timing ICS525R-08 OSCaR-family user-configurable clock option يُستخدم في: Industrial Control and Instrumentation, Network Interface and Processor Timing
What is the ICS525R-04 clock generator used for?
The ICS525R-04 generates a user-configurable differential PECL clock up to 200 MHz for high-speed digital systems. According to the manufacturer datasheet, it accepts a CMOS or crystal reference, uses a PLL, and supports hardware configuration without firmware. It is suited to line cards, serial links, FPGA clocking, telecommunications equipment, and test systems requiring a local 5 V PECL clock source.
What is the maximum frequency of ICS525R-04?
The ICS525R-04 operates up to 200 MHz. The manufacturer datasheet identifies the device as a clock generator with a maximum frequency of 200 MHz and a differential PECL output. This rating makes it relevant for source-synchronous interfaces, high-speed serial links, communications processors, and FPGA input or output clocking. Actual usable frequency and timing margin must be checked for the selected reference and configuration.
What supply voltage does ICS525R-04 require?
The ICS525R-04 requires a 4.5 V to 5.5 V supply. According to the manufacturer datasheet, the device operates from a nominal 5 V rail within that range and produces differential PECL clock outputs. A regulated supply, local decoupling, and adequate return-path continuity are important for stable clock generation and clean edge quality in high-speed systems.
Where can I download the ICS525R-04 datasheet PDF?
The ICS525R-04 datasheet is available through the linked datasheet record, with a separate record covering the tape-and-reel suffix variant. The manufacturer document describes the OSCaR user-configurable PECL clock, while the electronic copy also provides the seven-page document. Use the pin-description table and typical application circuit from the manufacturer datasheet when assigning PCB nets and selecting external components.
Where is the ICS525R-04 pinout located?
The ICS525R-04 pinout is located in the pin-description table of the manufacturer datasheet. The device uses a 28-pin SSOP package, and its architecture includes power, ground, crystal or CMOS input, configuration-select, and differential PECL output connections. Use the package drawing to identify all 28 positions and preserve the differential output pairing when assigning PCB tracks.
Does ICS525R-04 use a crystal or CMOS input?
The ICS525R-04 supports either a crystal or CMOS reference input. According to the manufacturer datasheet, the input interface is listed as CMOS or crystal, while the PLL supports generation of a high-frequency differential PECL output. The external reference arrangement and crystal load requirements must follow the typical application circuit rather than treating the input as a general-purpose logic signal.
Is ICS525R-04 programmable by software?
No. The ICS525R-04 is configured through hardware select pins, so no microcontroller, firmware, or device programmer is required to establish its operating configuration. The manufacturer datasheet identifies it as a user-configurable clock, while the OSCaR family description states that select-pin states determine the configuration. Review the complete truth table before assigning those pins.
ICS525R-04 vs ICS525R-02 — which is the better clock generator?
ICS525R-04 is the preferable choice when the required OSCaR configuration is the -04 ratio implementation or its associated output definition. ICS525R-02 is a closely related 28-SSOP clock generator, but the nominal configuration code differs from 04. Both belong to the same user-configurable PECL-clock family and use a 28-pin SSOP; final selection depends on the reference frequency and output ratio required by the design.
When should I choose ICS525R-04 over ICS525R-01?
Choose ICS525R-04 when the clock tree has been designed around the -04 configuration and its associated output ratio. Choose ICS525R-01 only after confirming that its configuration code produces the required frequency relationship from the available crystal or CMOS reference. Both parts belong to the same OSCaR family and use the same 28-pin SSOP format, making PCB reuse possible when timing parameters are compatible.
Is ICS525R-04 suitable for FPGA and DSP clocking?
The ICS525R-04 is suitable for FPGA and DSP clocking when the target accepts a compatible differential PECL clock and the design operates within the device's 200 MHz limit and 4.5 V to 5.5 V supply range. Its PLL-based clock generation can provide a local reference from a crystal or CMOS source. Confirm edge rate, jitter, supply sequencing, and input thresholds before production release.
What can replace ICS525R-04 without changing the PCB?
A PCB-compatible replacement must use the same 28-pin SSOP footprint, provide compatible power and ground connections, support the required configuration pins, and reproduce the -04 clock function. Closest choices are other OSCaR configuration-code variants from the same manufacturer family, provided their output ratio matches. The ICS525R-02 is one confirmed 28-SSOP relative, but no cross-brand pin-compatible substitute was established for direct replacement.
Is ICS525R-04 the same as ICS525R-04T?
The ICS525R-04 and ICS525R-04T represent the same core clock-generator configuration in different orderable suffix forms, with the T designation identifying a packaging or shipment option. For a new PCB, confirm the exact suffix, pin count, dimensions, temperature range, and orientation against the manufacturer ordering table. Packaging suffixes should not be treated as different functional devices.
Where can I buy ICS525R-04 and what is its current lead time?
Use the Request a Quote form on this page to request the current price, stock position, minimum order quantity, and lead time for ICS525R-04. The listed inventory count is a point-in-time market signal rather than a guaranteed allocation. An authorized purchasing review should confirm the exact MPN, package suffix, delivery schedule, and traceability requirements before placing an order.
How much does ICS525R-04 cost?
The current commercial terms for ICS525R-04 should be requested through the Request a Quote form on this page. The quote can reflect the exact order suffix, required quantity, delivery destination, and production schedule. This is preferable to relying on an obsolete catalog figure because clock-generator pricing and availability can vary with configuration, package suffix, and supply status.
Is ICS525R-04 currently in stock?
A distributor result reports substantial inventory for ICS525R-04, but that statement is a point-in-time market indication and not a reserved allocation. Use the Request a Quote form on this page to request confirmation of current stock, scheduled delivery, and minimum order quantity. Production planners should also verify the exact suffix and include a safety-stock allowance for the lead time returned with the quotation.
What are the key specifications of ICS525R-04 that engineers should know?
The principal ICS525R-04 specifications are a 200 MHz maximum frequency, differential PECL output, CMOS-or-crystal reference input, PLL capability, a 4.5 V to 5.5 V supply range, and a 28-pin SSOP package. According to the manufacturer datasheet, the output configuration is selected through hardware pins rather than firmware. These characteristics determine its suitability for high-speed digital clock trees and PCB replacement decisions.
Is there a verified cross-brand equivalent for ICS525R-04?
No cross-brand drop-in equivalent was verified for the ICS525R-04. The available cross-reference information identifies same-family OSCaR relatives and generic search tools but does not establish another manufacturer's part with identical pin assignment, configuration semantics, supply requirements, and clock performance. For a cross-brand replacement, require manufacturer confirmation or a complete application-level review rather than treating a similar maximum frequency as sufficient.

بيانات مرجعية هندسية لـ ICS525R-04 — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the ICS525R-04 when the clock plan specifically calls for the OSCaR -04 configuration, a differential PECL output, and a maximum operating frequency of 200 MHz. It is especially useful where the reference is a crystal or CMOS source and the clock must be configured through hardware rather than firmware. Choose ICS525R-02 only when the -02 ratio implementation produces the required frequency; its package is the same, but the configuration code is not interchangeable merely because both are 28-pin SSOP devices. The other listed same-family variants require the same reference-frequency and output-ratio review. No cross-brand drop-in alternative is established, so a competitor part should not be approved solely from a matching maximum frequency or package count. Before release, confirm the complete pin description, operating temperature, jitter, output levels, and exact orderable suffix.

المقارنة مع البدائل

المعامل هذا المنتج ICS525R-01 ICS525R-02 ICS525R-03 ICS525R-06 ICS525R-08
Package 28-pin SSOP 28-pin SSOP 28-pin SSOP 28-pin SSOP 28-pin SSOP 28-pin SSOP
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Configuration Code 04 01 02 03 06 08

أبرز الفروقات

  • Configuration-specific -04 clock behavior (مقابلICS525R-02)
  • Direct 28-pin SSOP family positioning (مقابلICS525R-01)
  • Hardware-configurable operation (مقابلICS525R-03)

ملاحظات التصميم

Route the two PECL outputs as a tightly coupled differential pair with symmetrical vias and uninterrupted reference planes. Keep the pair away from switching-regulator power nodes, high-current return paths, and unrelated high-speed signals. Because the device uses a 28-pin SSOP with 0.150 inch lead spacing, verify fanout on all layers and avoid long exposed stubs between the device and its PECL termination network.

Use a stable 5 V source within the device's 4.5 V to 5.5 V operating range and place local high-frequency decoupling directly across the supply and ground pins. Preserve a low-impedance ground return rather than relying on a distant ground plane connection. Sequence and test the supply ramp because changes in reference stability or supply noise can affect clock edge quality even when the nominal output frequency remains correct.

Configure the hardware-select pins according to the manufacturer truth table and add pull resistors where required to prevent accidental states during reset or board handling. Keep the crystal, reference input, and PLL circuitry away from noisy sources. Confirm output termination, loading, target-device thresholds, edge rate, duty-cycle distortion, and jitter at the receiver rather than evaluating the clock only at the oscillator pins.

Do not assume that an OSCaR family member with the same SSOP footprint is an automatic functional substitute. The nominal configuration code can determine the output ratio from the selected reference, so verify the frequency plan, select-pin levels, and downstream requirements. Similarly, distinguish the base MPN from orderable suffix variants and confirm the exact package, temperature grade, and reel format against the ordering information.

معلومات الامتثال

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

RoHS-compliant status is identified for the SSOP-28 package variants. No specific REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was established for the exact target MPN.

تم التحقق من البيانات في: 2026-11-16 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ICS525R-04 datasheet ICS525R-04 pinout ICS525R-04 datasheet pdf ICS525R-04 specifications ICS525R-04 equivalent ICS525R-04 replacement ICS525R-04 cross reference ICS525R-04 vs ICS525R-02 ICS525R-04 SSOP-28 ICS525R-04 200MHz PECL ICS525R-04 price ICS525R-04 stock Renesas ICS525R-04 ICS525R-04 FPGA clock ICS525R-04 application circuit

المكونات والمصطلحات ذات الصلة

Renesas Electronics ICS525R-04 ICS525R-01 ICS525R-02 ICS525R-03 ICS525R-06 ICS525R-08 OSCaR clock generator clock and timing IC semiconductor phase-locked loop PLL PECL differential clock output CMOS input crystal oscillator user-configurable clock SSOP-28 surface-mount package RoHS hardware select pins telecommunications clocking FPGA source-synchronous clocking 200 MHz
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر