ICS525R-04 - 200MHz PECL Clock Generator | Renesas
MPN: ICS525R-04 ✓ Hoạt độngICS525R-04 Tóm tắt
A clock generator is an integrated timing component that creates, conditions, and distributes a stable frequency reference through a system. The OSCaR family combines a phase-locked loop with selectable configuration pins, placing clock generation in the Clock & Timing IC category within the broader semiconductor and power-management ecosystem. Unlike a simple crystal oscillator, this architecture can support user-selectable output relationships and provide PECL-compatible differential outputs for high-speed digital circuitry.
The ICS525R-04 supports a maximum operating frequency of 200 MHz and uses a PECL output interface. Configuration can be established through hardware-select pins rather than firmware or a device programmer, making the part useful where deterministic setup and minimal firmware support are priorities. The 4.5 V to 5.5 V supply range and SSOP-28 surface-mount package support established 5 V digital clocking systems.
Internally, the OSCaR architecture uses a PLL to multiply or divide a crystal or external clock reference and generate the required output frequency. A PLL-based approach provides programmable frequency relationships while retaining a stable external reference. Differential PECL outputs are suited to short-reach, point-to-point interconnects where source-synchronous clocking, serializer/deserializer interfaces, or high-speed digital logic require low-skew clock distribution.
Typical uses include telecommunications line cards, network-interface clock trees, high-speed serial links, test-and-measurement equipment, and industrial control systems. The same clock-generation approach can also support digital signal processors, FPGA clock planes, and communications processors when the system needs a locally generated PECL reference rather than a panel-distributed clock.
When laying out the circuit, place the crystal and input decoupling close to the device and route differential outputs as a tightly matched pair with uninterrupted reference planes. The 28-pin SSOP footprint requires careful fanout because its narrow lead pitch can constrain escape routing on multilayer boards. Verify configuration-pin states during power-up and validate output frequency and duty-cycle behavior across the complete operating temperature range.
This product record combines the oscillator function, principal electrical characteristics, package details, sourcing information, and practical implementation guidance in one engineering-focused reference. It also distinguishes verified device attributes from parameters that require confirmation from the manufacturer datasheet, helping designers move from component selection to a complete clock-tree design with fewer documentation gaps.
Bộ thay thế dễ dàng lắp đặt cho ICS525R-04 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
ICS525R-01
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ICS525R-02
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ICS525R-03
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ICS525R-06
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ICS525R-08
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ICS525R-04 Thông số kỹ thuật
| Device Type | Clock Generator |
| Product Family | OSCaR |
| Maximum Frequency | 200 MHz |
| Number of Circuits | 1 |
| PLL | Yes |
| Input Interface | CMOS or Crystal |
| Output Interface | Differential PECL |
| Cấu hình đầu ra | User Configurable |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Hộp | 28-pin SSOP, 0.150 inch pitch |
| Kiểu lắp đặt | Surface Mount |
| Package Outline Reference | MO-153 |
| Trạng thái RoHS | Compliant |
| Configuration Method | Hardware select pins |
| Programming Requirement | None |
Hướng dẫn cấu hình chân ICS525R-04 mo-153
Cấu hình chân cho ICS525R-04 (mo-153 gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ICS525R-04.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ICS525R-04 phù hợp cho 6 Áp dụngs: Telecommunications Line-Card Clocking, FPGA Source-Synchronous Clocking, High-Speed Serial Link Clock Reference, Industrial Control and Instrumentation, Test and Measurement Clock Trees, Network Interface and Processor Timing.
Telecommunications Line-Card Clocking
The ICS525R-04 fits telecommunications line-card clock trees that require a locally generated differential PECL clock. Its PLL-based architecture can operate from a crystal or CMOS reference and supports user configuration through hardware pins, eliminating firmware setup for the clock device. The 200 MHz maximum frequency provides useful headroom for high-speed line-card logic, while the 4.5 V to 5.5 V operating range aligns with conventional 5 V backplane equipment. Differential PECL outputs are particularly useful when the clock must traverse a controlled, short-reach connection between clock-generation and interface circuitry.
Được đề xuất
FPGA Source-Synchronous Clocking
The ICS525R-04 is suitable for generating a differential reference for FPGA source-synchronous interfaces when the required clock does not exceed 200 MHz. Hardware-selectable configuration allows the clock function to be established independently of FPGA firmware, which can simplify boot sequencing and board bring-up. The PLL accepts a crystal or CMOS reference so the design can use either an onboard resonator or a shared reference. Designers should verify the FPGA's input threshold, clock-input architecture, and maximum operating frequency before connecting the PECL output.
Được đề xuất
High-Speed Serial Link Clock Reference
The ICS525R-04 can provide a stable differential PECL reference for high-speed serial links that require coordinated transmit and receive clocking. Its 200 MHz ceiling supports demanding parallel-clock or divided-clock architectures, while the PLL provides a controllable relationship between the external reference and generated outputs. Because PECL links are sensitive to routing and termination, the implementation should use matched differential routing, continuous reference planes, and the termination network shown in the manufacturer application circuit.
Được đề xuất
Industrial Control and Instrumentation
The ICS525R-04 supports industrial control and test-instrumentation subsystems that need deterministic timing without a software-programmed clock source. Its hardware configuration method is useful in equipment where startup behavior must be controlled by straps, GPIO defaults, or other fixed hardware. The 28-pin SSOP package supports compact, surface-mounted designs, and the 4.5 V to 5.5 V supply range fits common 5 V analog and digital subsystems. Engineers should account for the narrow package pitch and route clock traces away from switching-power and high-current return paths.
Được đề xuất
Test and Measurement Clock Trees
The ICS525R-04 is appropriate for test and measurement equipment that distributes a local high-speed clock to acquisition, conversion, or digital processing sections. A 200 MHz differential PECL clock can feed compatible instrumentation blocks when clean edge rates and deterministic phase relationships are important. The device can be driven from a crystal or CMOS source, allowing reference selection according to calibration requirements. Production validation should cover frequency accuracy, duty-cycle distortion, output amplitude, and jitter using the same loading and termination intended for the final instrument.
Được đề xuất
Network Interface and Processor Timing
The ICS525R-04 can support processor and network-interface timing islands that require a local clock derived from a common reference. Its PLL architecture permits a crystal or CMOS input to drive a controlled differential output, and its user-selectable configuration avoids tying clock setup to software initialization. The 200 MHz maximum frequency is relevant to interfaces operating at one-half, one-third, or another programmed ratio of the reference, subject to the device configuration table. Integration requires checking the downstream device's PECL input limits and sequencing requirements against the power ramp.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ICS525R-04 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ICS525R-01 | ICS525R-02 | ICS525R-03 | ICS525R-06 | ICS525R-08 |
|---|---|---|---|---|---|---|
| Package | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Configuration Code | 04 | 01 | 02 | 03 | 06 | 08 |
Bảo phân biệt quan trọng
- Configuration-specific -04 clock behavior (vsICS525R-02)
- Direct 28-pin SSOP family positioning (vsICS525R-01)
- Hardware-configurable operation (vsICS525R-03)
Ghi chú thiết kế
Route the two PECL outputs as a tightly coupled differential pair with symmetrical vias and uninterrupted reference planes. Keep the pair away from switching-regulator power nodes, high-current return paths, and unrelated high-speed signals. Because the device uses a 28-pin SSOP with 0.150 inch lead spacing, verify fanout on all layers and avoid long exposed stubs between the device and its PECL termination network.
Use a stable 5 V source within the device's 4.5 V to 5.5 V operating range and place local high-frequency decoupling directly across the supply and ground pins. Preserve a low-impedance ground return rather than relying on a distant ground plane connection. Sequence and test the supply ramp because changes in reference stability or supply noise can affect clock edge quality even when the nominal output frequency remains correct.
Configure the hardware-select pins according to the manufacturer truth table and add pull resistors where required to prevent accidental states during reset or board handling. Keep the crystal, reference input, and PLL circuitry away from noisy sources. Confirm output termination, loading, target-device thresholds, edge rate, duty-cycle distortion, and jitter at the receiver rather than evaluating the clock only at the oscillator pins.
Do not assume that an OSCaR family member with the same SSOP footprint is an automatic functional substitute. The nominal configuration code can determine the output ratio from the selected reference, so verify the frequency plan, select-pin levels, and downstream requirements. Similarly, distinguish the base MPN from orderable suffix variants and confirm the exact package, temperature grade, and reel format against the ordering information.
Thông tin tuân thủ
RoHS-compliant status is identified for the SSOP-28 package variants. No specific REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was established for the exact target MPN.