Texas Instruments

INA141UAE4 - Precision Gain-10/100 Instrumentation Amplifier | TI

MPN: INA141UAE4 ✓ نشط
2.25 V to 18 V Vdss 8-pin SOIC Package
الحد الأدنى للطلب: 1 |

INA141UAE4 نظرة عامة

The Texas Instruments INA141UAE4 is a low-power, precision three-op-amp instrumentation amplifier available in an 8-pin SOIC package. It supports fixed gains of 10 V/V and 100 V/V, operates from 2.25 V to 18 V, and combines a 250 V maximum input range with a slew rate of 4 V/µs. Current-feedback input circuitry maintains 200 kHz bandwidth at a gain of 100.

An instrumentation amplifier is a specialized analog amplifier designed for low-level differential measurements. Its internal three-op-amp architecture measures the voltage between two input terminals while rejecting common-mode signals produced by ground offsets, motor noise, supply variation, or other shared disturbances. The INA141 belongs to the broader hierarchy of instrumentation amplifiers, precision analog amplifiers, and integrated amplifier ICs used for sensor and signal-chain conditioning.

The principal gains are 10 V/V and 100 V/V, allowing the same device family to serve both moderate-amplification and high-amplification signal paths. A maximum input voltage of 250 V provides substantial headroom for high-voltage measurement systems. Its 200 kHz bandwidth at a gain of 100 V/V is particularly important because many instrumentation amplifiers lose usable bandwidth as gain increases; the current-feedback architecture helps the INA141 preserve bandwidth in higher-gain configurations.

The three-op-amp structure provides matched internal resistors and a straightforward gain-selection arrangement, reducing the number of precision external components normally required by discrete implementations. The 2.25 V minimum supply voltage also supports lower-voltage analog systems, while the 18 V maximum supply rating accommodates conventional industrial supply ranges. The result is a compact analog front end for sensor signals where accuracy, common-mode rejection, and stable gain are more important than general-purpose op-amp flexibility.

Typical uses include bridge excitation and readout, current-shunt measurement, industrial pressure and temperature sensing, biomedical instrumentation, and low-level differential signal acquisition. At gain 10 V/V, the amplifier is appropriate when moderate amplification and wider bandwidth are priorities. At gain 100 V/V, it is better suited to small sensor outputs where additional signal amplification is required, although circuit bandwidth, input common-mode range, output swing, and noise must still be checked against the actual operating point.

PCB design should preserve the symmetry of the differential input routes and provide a quiet ground return for the analog signals. Decoupling capacitors should be placed close to the supply pins, while input and feedback connections should be kept short to minimize added noise and imbalance. System-level protection may also be needed because the input-voltage rating and the usable signal range are not the same specification.

This page organizes the INA141UAE4 electrical characteristics, ordering information, package details, drop-in candidates, and application guidance into a design-focused reference. It also identifies where engineers must consult the manufacturer datasheet and pin-description table before assigning PCB tracks or committing to a replacement.

بدائل مباشرة لـ INA141UAE4 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع INA141UAE4 (نفس عامل الشكل والبصمة) — يختلف في Package, Amplifier Type, Supply Voltage Range.

Texas Instruments
Amplifier Type: Instrumentation amplifier
Supply Voltage Range: ±18 V
قارن مع INA141UAE4 →
Texas Instruments
Package: 8-SOIC, 0.154 inch body width, 3.90 mm width
قارن مع INA141UAE4 →

INA141UA

✅ بديل مباشر
Texas Instruments
📦 8-pin SOIC
Instrumentation amplifier · Three-op-amp design · 1 circuit · 10 V/V or 100 V/V · 200 kHz · 50 µV · 0.5 µV/°C · 5 nA

تواصل لمعرفة السعر

عرض ورقة البيانات ←

INA141UAG4

✅ بديل مباشر
Texas Instruments
📦 8-pin SOIC
Precision low-power instrumentation amplifier · 3 amplifiers · 10 or 100 · 1 MHz · 110 dB · 20 µV · 250 µV · 8 nV/√Hz

تواصل لمعرفة السعر

عرض ورقة البيانات ←

INA141UAE4 الحدود القصوى والخصائص الكهربائية

Amplifier Type Precision instrumentation amplifier
Architecture Three-op-amp design
Fixed Gain 10 V/V
Fixed Gain 100 V/V
Supply Voltage Range 2.25 V to 18 V
Maximum Input Voltage 250 V
Bandwidth at Gain 100 200 kHz
Slew Rate 4 V/µs
Input Circuitry Current-feedback
Power Class Low-power
Number of Circuits 1 circuit
العلبة 8-pin SOIC
Terminal Count 8 terminals
Package Shape Rectangular
Terminal Form Gull wing
Temperature Grade Industrial
نوع التركيب Surface mount
حالة RoHS Compliant

دليل تكوين أطراف INA141UAE4 rectangular

تكوين الأطراف لـ INA141UAE4 (حزمة rectangular). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة rectangular لـ INA141UAE4

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ INA141UAE4.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

INA141UAE4 مناسب لـ 6 التطبيقs: Industrial Bridge Sensor Front End, Current Shunt Measurement, Precision Temperature Sensing, Biomedical Instrumentation, Data Acquisition and Test Equipment, Low-Level Differential Signal Conditioning.

🏭

Industrial Bridge Sensor Front End

The INA141UAE4 suits resistive bridge measurement systems where the sensor produces a small differential signal on top of a larger common-mode voltage. Its fixed gains of 10 V/V and 100 V/V provide two useful scaling options without external gain-setting networks. According to the Texas Instruments INA141 datasheet, the current-feedback input circuitry retains 200 kHz bandwidth at gain 100, making the device suitable for pressure, force, and position bridges with moderate dynamic requirements. The 8-pin SOIC footprint simplifies analog-board integration. Design the amplifier around the bridge excitation voltage, verify that the bridge output remains inside the input common-mode range at gain 100, and place supply bypass capacitors close to the device pins.

⚡

Current Shunt Measurement

The INA141UAE4 can measure the differential voltage produced by a current shunt while rejecting voltage shared by both shunt terminals. A gain of 10 V/V is useful for moderate shunt signals, whereas 100 V/V increases sensitivity to small currents and can reduce the amplitude that must be handled by a downstream ADC. The Texas Instruments INA141 datasheet reports 200 kHz bandwidth at gain 100 and a slew rate of 4 V/µs, supporting higher-bandwidth current-loop monitoring than a purely low-frequency precision amplifier. Keep the shunt connections short and symmetrical to minimize parasitic resistance and common-mode conversion. Confirm output swing and verify that the input common-mode voltage remains valid under all operating current.

🌡️

Precision Temperature Sensing

The INA141UAE4 is appropriate for thermocouple, RTD, or semiconductor temperature-sensor interfaces when the required gain is fixed at 10 V/V or 100 V/V. Low-level sensor voltages benefit from the device’s precision three-op-amp architecture and differential input stage, which are intended to suppress common-mode disturbances on long sensor wiring. The 2.25 V to 18 V operating range permits use with low-voltage and conventional industrial rails. For thermocouple systems, cold-junction compensation remains a separate circuit requirement. For RTDs, excitation current and self-heating must be controlled. Use gain 100 only when its common-mode range and 200 kHz bandwidth behavior suit the sensor and measurement bandwidth.

💊

Biomedical Instrumentation

The INA141UAE4 can form the analog input stage of biomedical instrumentation when it measures a small differential physiological signal and the system provides the required isolation, protection, and safety controls. Its low-power design, fixed gains, and differential common-mode rejection support compact sensing electronics. The Texas Instruments INA141 datasheet describes the device as a precision, low-power, general-purpose instrumentation amplifier with a three-op-amp architecture. Because the INA141UAE4 is not identified as an automatically acceptable medical-system solution, engineers should evaluate input protection, patient leakage, diagnostic classification, applicable standards, and noise performance at the complete circuit level. Route sensitive inputs away from switching nodes and establish an analog ground strategy.

🔧

Data Acquisition and Test Equipment

The INA141UAE4 is useful in compact data-acquisition front ends that need to measure low-level differential channels while controlling board area. The fixed 10 V/V and 100 V/V gains simplify gain routing, and the 200 kHz bandwidth at gain 100 provides useful signal bandwidth according to the Texas Instruments INA141 datasheet. In multiplexed systems, settling time, input capacitance, and channel-to-channel switching must be evaluated separately. The 8-pin SOIC package is compatible with conventional surface-mount PCB assembly, but analog routing quality remains essential. Keep input and gain-selection traces short, provide local supply bypass capacitance, and use a stable reference or excitation source when the measured quantity depends on one.

📡

Low-Level Differential Signal Conditioning

The INA141UAE4 provides a compact way to condition small differential signals that share a common-mode voltage, such as outputs from Wheatstone bridges, strain gauges, magnetic sensing elements, and programmable sensors. Its internal three-op-amp design reduces the component count compared with a discrete matched-resistor implementation, while the fixed gains offer predictable scaling. The 250 V maximum input rating provides margin in appropriately protected high-voltage measurement circuits, but it does not remove the need for input protection. According to the Texas Instruments INA141 datasheet, the device combines low power with 200 kHz bandwidth at gain 100. Engineers should verify common-mode limits, output swing, noise, and stability with the actual source impedance.

What is the operating voltage of INA141UAE4?
The INA141UAE4 operates from 2.25 V to 18 V according to the Texas Instruments INA141 datasheet. This range allows the amplifier to operate from low-voltage analog rails as well as conventional industrial supply systems. Designers should also verify the input common-mode range, output-voltage swing, and supply decoupling requirements at the selected operating voltage rather than relying on the supply rating alone.
What are the key specifications of INA141UAE4 that engineers should know?
The INA141UAE4 is a single-circuit, low-power instrumentation amplifier with fixed gains of 10 V/V and 100 V/V, according to the Texas Instruments INA141 datasheet. It accepts a supply from 2.25 V to 18 V, has a 250 V maximum input rating, and provides 200 kHz bandwidth at a gain of 100 V/V. The device is packaged in an 8-pin SOIC and uses a three-op-amp architecture.
What is the bandwidth of INA141UAE4 at gain 100?
The INA141UAE4 provides 200 kHz bandwidth at a gain of 100 V/V according to the Texas Instruments INA141 datasheet. This high-gain bandwidth results from its current-feedback input circuitry. The bandwidth figure applies to the specified gain condition and must be considered together with slew rate, output amplitude, and the frequency response required by the sensor and signal chain.
Where can I download the INA141UAE4 datasheet PDF?
The official INA141UAE4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ina141.pdf. The document contains the electrical characteristics, gain-selection information, typical application circuits, package drawings, and pin descriptions. Use the Texas Instruments product page for ordering information and current lifecycle details when evaluating procurement requirements.
Where can I find the INA141UAE4 pinout?
The INA141UAE4 pin assignments are shown in the Texas Instruments INA141 datasheet under the package and pin-configuration information. The device is an 8-pin SOIC, so its physical footprint uses gull-wing leads and standard SOIC-8 board geometry. Use the datasheet pin-description table when assigning input, supply, output, and gain-setting connections.
Is INA141UAE4 suitable for industrial sensor measurement?
Yes, the INA141UAE4 is suitable for many industrial sensor-measurement circuits because the Texas Instruments INA141 datasheet identifies an industrial temperature grade and a 2.25 V to 18 V supply range. Its fixed gains of 10 V/V and 100 V/V are useful for bridge outputs, shunt signals, and other small differential inputs. Confirm common-mode limits, output swing, noise, and bandwidth for the specific sensor.
What can replace INA141UAE4?
The INA141UA is a pin-compatible candidate in the same 8-pin SOIC footprint because the Texas Instruments listing identifies it as the same INA141 instrumentation-amplifier family in an 8-SOIC package. The INA141UAG4 is another family member identified by cross-reference data. Final replacement approval should confirm the exact gain configuration, temperature grade, supply limits, and ordering suffix against the manufacturer datasheet.
Is INA141UAE4 the same as INA141UA?
The INA141UA and INA141UAE4 belong to the same Texas Instruments INA141 family and use an 8-pin SOIC package, but their ordering suffixes should not be treated as automatically interchangeable. The INA141UA is the base catalog entry, while INA141UAE4 is the fully specified orderable MPN. Compare temperature grade, reel or tube packing, and any suffix-specific ordering attributes before substitution.
When should I choose INA141UAE4 over a general-purpose op amp?
Choose the INA141UAE4 when the source is a small differential signal and common-mode rejection, fixed gain, and compact implementation matter more than op-amp flexibility. According to the Texas Instruments INA141 datasheet, its three-op-amp architecture provides fixed gains of 10 V/V and 100 V/V. A general-purpose op amp may be preferable when the signal requires programmable gain, unusual output drive, or custom feedback arrangements.
INA141UAE4 vs INA141UA — which is better for a new design?
The INA141UAE4 is preferable when a product order requires that exact manufacturer MPN and its associated ordering, grade, and packing attributes. The INA141UA is a valid 8-pin SOIC catalog alternative for many designs because it is listed as the same INA141 instrumentation-amplifier family. For an existing PCB, the decisive checks are package geometry, gain, temperature grade, supply range, and suffix-specific ordering requirements.
Where to buy INA141UAE4 online?
The INA141UAE4 can be requested through the Request a Quote form on this page. The form is the appropriate route for current commercial terms, stock confirmation, lead time, and minimum-order quantity. Quote responses should identify the exact Texas Instruments MPN INA141UAE4 and the required 8-pin SOIC packing and quantity so that the order remains unambiguous.
What is the price of INA141UAE4?
Current pricing for INA141UAE4 should be obtained through the Request a Quote form on this page because commercial prices and availability can change with quantity and supply conditions. The request should specify the quantity, package packing, and delivery requirements. This ensures the quotation applies to the exact INA141UAE4 orderable part rather than a related INA141 family member.
What is the lead time for INA141UAE4?
The current lead time and available quantity for INA141UAE4 should be confirmed through the Request a Quote form on this page. Lead time can depend on order quantity, factory schedule, packaging, and shipment destination. Providing the required quantity, target date, and delivery country enables a commercial response tied to the exact Texas Instruments part number.
Is INA141UAE4 in stock?
Current INA141UAE4 stock status should be confirmed through the Request a Quote form on this page. The form accepts the required part number and quantity and allows the supplier response to reflect the latest available inventory. Buyers should specify whether reel, tube, or another permitted 8-pin SOIC packing is required.
Does INA141UAE4 support medical and precision measurement designs?
The INA141UAE4 can be used in precision differential-signal front ends, including medical and industrial instrumentation, when its electrical limits satisfy the application. The Texas Instruments INA141 datasheet describes excellent accuracy, a three-op-amp design, fixed gains of 10 V/V and 100 V/V, and low power. Medical designs still require application-specific safety, isolation, noise, and qualification review.

بيانات مرجعية هندسية لـ INA141UAE4 — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the INA141UAE4 when the design requires the exact Texas Instruments order code, industrial-grade INA141 performance, fixed gains of 10 V/V or 100 V/V, and an 8-pin SOIC footprint. The INA141UA is the closest catalog alternative because it uses the same instrumentation-amplifier family and package; verify the exact suffix, grade, packing, and temperature requirements before release. The INA141UAG4 is another same-family option in the same SOIC outline, but its ordering attributes must be compared carefully. Use gain 10 V/V when bandwidth margin and output range are more important than maximum sensitivity. Use gain 100 V/V for small differential sensor outputs after confirming common-mode limits, output swing, settling, and noise. Neither alternative removes the need to review the manufacturer pin table and electrical characteristics for the final assembly.

المقارنة مع البدائل

المعامل هذا المنتج INA141UA INA141UAG4
Brand Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC
Product Type Precision low-power instrumentation amplifier INA141 instrumentation amplifier INA141 instrumentation amplifier
Fixed Gain 10 V/V or 100 V/V 10 V/V or 100 V/V 10 V/V or 100 V/V
Supply Voltage Range 2.25 V to 18 V 2.25 V to 18 V 2.25 V to 18 V
Maximum Input Voltage 250 V 250 V 250 V
Bandwidth at Gain 100 200 kHz 200 kHz 200 kHz
Slew Rate 4 V/µs 4 V/µs 4 V/µs
Internal Architecture Three-op-amp design with current-feedback input circuitry Three-op-amp INA141 architecture Three-op-amp INA141 architecture

أبرز الفروقات

  • Preserves useful bandwidth at the higher fixed gain (مقابلINA141UA)
  • Uses the same family and package as the base catalog device (مقابلINA141UA)
  • Provides a same-family G4 ordering option (مقابلINA141UAG4)

ملاحظات التصميم

Route the two input paths as a closely matched differential pair, with comparable geometry, short connections, and minimal exposure to switching nodes. The INA141 uses current-feedback input circuitry, so unequal input impedance or trace resistance can create gain imbalance and degrade common-mode rejection. Place the gain-setting and feedback components indicated by the manufacturer application diagram near the device, and maintain symmetric grounding around the analog channel.

Do not treat the 250 V maximum input rating as permission to apply arbitrary high-voltage signals without protection. At gain 100, verify the valid input common-mode range, output swing, and external overvoltage behavior for the selected 2.25 V to 18 V supply. Input clamping, series resistance, and fault-current limits may be required. The maximum input specification and the usable operating range are distinct constraints and both must be satisfied.

Place the supply bypass capacitor close to the amplifier’s supply pins and connect it through a short return path to the same analog ground reference used by the signal source. If the source has substantial capacitance, include it in stability and settling analysis rather than relying only on the nominal 200 kHz bandwidth figure. For gain 100, preserve low parasitic capacitance and symmetric routing to avoid degrading the high-gain frequency response.

Estimated power consumption equals the applied supply voltage multiplied by the device’s operating current under the actual load and bias condition. The applicable supply is between 2.25 V and 18 V, but the operating current must be taken from the manufacturer datasheet for the selected condition. Verify that the upstream regulator can support the amplifier, source resistance, protection network, and any attached sensor excitation current without producing unacceptable rail noise or voltage droop.

Choose gain 10 V/V when the signal can be captured with more bandwidth margin or less output amplification. Choose gain 100 V/V when the source signal is small and requires greater sensitivity, but recheck output headroom, input common-mode limits, noise, and settling behavior. The Texas Instruments INA141 datasheet specifies 200 kHz bandwidth at gain 100; that condition should not be generalized to every gain, source impedance, and output-amplitude combination.

معلومات الامتثال

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

RoHS compliance is identified for the INA141 family. The industrial-grade device is not presented as an AEC-Q100-qualified automotive option. Other environmental and material compliance attributes are not established by the cited product information.

تم التحقق من البيانات في: 2026-11-14 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

INA141UAE4 datasheet INA141UAE4 datasheet pdf INA141UAE4 pinout INA141UAE4 specifications INA141UAE4 price INA141UAE4 stock INA141UAE4 equivalent INA141UAE4 replacement INA141UAE4 vs INA141UA INA141UAE4 SOIC-8 footprint Texas Instruments INA141UAE4 INA141UAE4 instrumentation amplifier INA141UAE4 bridge sensor application INA141 gain 100 bandwidth what can replace INA141UAE4

المكونات والمصطلحات ذات الصلة

Texas Instruments INA141 INA141UAE4 INA141UA INA141UAG4 precision instrumentation amplifier three-op-amp instrumentation amplifier analog amplifier IC low-dropout power differential input common-mode rejection current-feedback input circuitry fixed gain 10 V/V gain 100 V/V gain 200 kHz bandwidth 4 V/µs slew rate 250 V maximum input voltage 2.25 V to 18 V supply 8-pin SOIC SOIC package family surface-mount device RoHS industrial instrumentation bridge sensor measurement
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر