INA141UAE4 - Precision Gain-10/100 Instrumentation Amplifier | TI
MPN: INA141UAE4 ✓ Hoạt độngINA141UAE4 Tóm tắt
An instrumentation amplifier is a specialized analog amplifier designed for low-level differential measurements. Its internal three-op-amp architecture measures the voltage between two input terminals while rejecting common-mode signals produced by ground offsets, motor noise, supply variation, or other shared disturbances. The INA141 belongs to the broader hierarchy of instrumentation amplifiers, precision analog amplifiers, and integrated amplifier ICs used for sensor and signal-chain conditioning.
The principal gains are 10 V/V and 100 V/V, allowing the same device family to serve both moderate-amplification and high-amplification signal paths. A maximum input voltage of 250 V provides substantial headroom for high-voltage measurement systems. Its 200 kHz bandwidth at a gain of 100 V/V is particularly important because many instrumentation amplifiers lose usable bandwidth as gain increases; the current-feedback architecture helps the INA141 preserve bandwidth in higher-gain configurations.
The three-op-amp structure provides matched internal resistors and a straightforward gain-selection arrangement, reducing the number of precision external components normally required by discrete implementations. The 2.25 V minimum supply voltage also supports lower-voltage analog systems, while the 18 V maximum supply rating accommodates conventional industrial supply ranges. The result is a compact analog front end for sensor signals where accuracy, common-mode rejection, and stable gain are more important than general-purpose op-amp flexibility.
Typical uses include bridge excitation and readout, current-shunt measurement, industrial pressure and temperature sensing, biomedical instrumentation, and low-level differential signal acquisition. At gain 10 V/V, the amplifier is appropriate when moderate amplification and wider bandwidth are priorities. At gain 100 V/V, it is better suited to small sensor outputs where additional signal amplification is required, although circuit bandwidth, input common-mode range, output swing, and noise must still be checked against the actual operating point.
PCB design should preserve the symmetry of the differential input routes and provide a quiet ground return for the analog signals. Decoupling capacitors should be placed close to the supply pins, while input and feedback connections should be kept short to minimize added noise and imbalance. System-level protection may also be needed because the input-voltage rating and the usable signal range are not the same specification.
This page organizes the INA141UAE4 electrical characteristics, ordering information, package details, drop-in candidates, and application guidance into a design-focused reference. It also identifies where engineers must consult the manufacturer datasheet and pin-description table before assigning PCB tracks or committing to a replacement.
Bộ thay thế dễ dàng lắp đặt cho INA141UAE4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với INA141UAE4 (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Supply Voltage Range.
INA141UA
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →INA141UAG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →INA141UAE4 Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Precision instrumentation amplifier |
| Architecture | Three-op-amp design |
| Fixed Gain | 10 V/V |
| Fixed Gain | 100 V/V |
| Supply Voltage Range | 2.25 V to 18 V |
| Maximum Input Voltage | 250 V |
| Bandwidth at Gain 100 | 200 kHz |
| Slew Rate | 4 V/µs |
| Input Circuitry | Current-feedback |
| Power Class | Low-power |
| Number of Circuits | 1 circuit |
| Hộp | 8-pin SOIC |
| Terminal Count | 8 terminals |
| Package Shape | Rectangular |
| Terminal Form | Gull wing |
| Temperature Grade | Industrial |
| Kiểu lắp đặt | Surface mount |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân INA141UAE4 rectangular
Cấu hình chân cho INA141UAE4 (rectangular gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho INA141UAE4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
INA141UAE4 phù hợp cho 6 Áp dụngs: Industrial Bridge Sensor Front End, Current Shunt Measurement, Precision Temperature Sensing, Biomedical Instrumentation, Data Acquisition and Test Equipment, Low-Level Differential Signal Conditioning.
Industrial Bridge Sensor Front End
The INA141UAE4 suits resistive bridge measurement systems where the sensor produces a small differential signal on top of a larger common-mode voltage. Its fixed gains of 10 V/V and 100 V/V provide two useful scaling options without external gain-setting networks. According to the Texas Instruments INA141 datasheet, the current-feedback input circuitry retains 200 kHz bandwidth at gain 100, making the device suitable for pressure, force, and position bridges with moderate dynamic requirements. The 8-pin SOIC footprint simplifies analog-board integration. Design the amplifier around the bridge excitation voltage, verify that the bridge output remains inside the input common-mode range at gain 100, and place supply bypass capacitors close to the device pins.
Được đề xuất
Current Shunt Measurement
The INA141UAE4 can measure the differential voltage produced by a current shunt while rejecting voltage shared by both shunt terminals. A gain of 10 V/V is useful for moderate shunt signals, whereas 100 V/V increases sensitivity to small currents and can reduce the amplitude that must be handled by a downstream ADC. The Texas Instruments INA141 datasheet reports 200 kHz bandwidth at gain 100 and a slew rate of 4 V/µs, supporting higher-bandwidth current-loop monitoring than a purely low-frequency precision amplifier. Keep the shunt connections short and symmetrical to minimize parasitic resistance and common-mode conversion. Confirm output swing and verify that the input common-mode voltage remains valid under all operating current.
Được đề xuất
Precision Temperature Sensing
The INA141UAE4 is appropriate for thermocouple, RTD, or semiconductor temperature-sensor interfaces when the required gain is fixed at 10 V/V or 100 V/V. Low-level sensor voltages benefit from the device’s precision three-op-amp architecture and differential input stage, which are intended to suppress common-mode disturbances on long sensor wiring. The 2.25 V to 18 V operating range permits use with low-voltage and conventional industrial rails. For thermocouple systems, cold-junction compensation remains a separate circuit requirement. For RTDs, excitation current and self-heating must be controlled. Use gain 100 only when its common-mode range and 200 kHz bandwidth behavior suit the sensor and measurement bandwidth.
Được đề xuất
Biomedical Instrumentation
The INA141UAE4 can form the analog input stage of biomedical instrumentation when it measures a small differential physiological signal and the system provides the required isolation, protection, and safety controls. Its low-power design, fixed gains, and differential common-mode rejection support compact sensing electronics. The Texas Instruments INA141 datasheet describes the device as a precision, low-power, general-purpose instrumentation amplifier with a three-op-amp architecture. Because the INA141UAE4 is not identified as an automatically acceptable medical-system solution, engineers should evaluate input protection, patient leakage, diagnostic classification, applicable standards, and noise performance at the complete circuit level. Route sensitive inputs away from switching nodes and establish an analog ground strategy.
Được đề xuất
Data Acquisition and Test Equipment
The INA141UAE4 is useful in compact data-acquisition front ends that need to measure low-level differential channels while controlling board area. The fixed 10 V/V and 100 V/V gains simplify gain routing, and the 200 kHz bandwidth at gain 100 provides useful signal bandwidth according to the Texas Instruments INA141 datasheet. In multiplexed systems, settling time, input capacitance, and channel-to-channel switching must be evaluated separately. The 8-pin SOIC package is compatible with conventional surface-mount PCB assembly, but analog routing quality remains essential. Keep input and gain-selection traces short, provide local supply bypass capacitance, and use a stable reference or excitation source when the measured quantity depends on one.
Low-Level Differential Signal Conditioning
The INA141UAE4 provides a compact way to condition small differential signals that share a common-mode voltage, such as outputs from Wheatstone bridges, strain gauges, magnetic sensing elements, and programmable sensors. Its internal three-op-amp design reduces the component count compared with a discrete matched-resistor implementation, while the fixed gains offer predictable scaling. The 250 V maximum input rating provides margin in appropriately protected high-voltage measurement circuits, but it does not remove the need for input protection. According to the Texas Instruments INA141 datasheet, the device combines low power with 200 kHz bandwidth at gain 100. Engineers should verify common-mode limits, output swing, noise, and stability with the actual source impedance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho INA141UAE4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | INA141UA | INA141UAG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | Precision low-power instrumentation amplifier | INA141 instrumentation amplifier | INA141 instrumentation amplifier |
| Fixed Gain | 10 V/V or 100 V/V | 10 V/V or 100 V/V | 10 V/V or 100 V/V |
| Supply Voltage Range | 2.25 V to 18 V | 2.25 V to 18 V | 2.25 V to 18 V |
| Maximum Input Voltage | 250 V | 250 V | 250 V |
| Bandwidth at Gain 100 | 200 kHz | 200 kHz | 200 kHz |
| Slew Rate | 4 V/µs | 4 V/µs | 4 V/µs |
| Internal Architecture | Three-op-amp design with current-feedback input circuitry | Three-op-amp INA141 architecture | Three-op-amp INA141 architecture |
Bảo phân biệt quan trọng
- Preserves useful bandwidth at the higher fixed gain (vsINA141UA)
- Uses the same family and package as the base catalog device (vsINA141UA)
- Provides a same-family G4 ordering option (vsINA141UAG4)
Ghi chú thiết kế
Route the two input paths as a closely matched differential pair, with comparable geometry, short connections, and minimal exposure to switching nodes. The INA141 uses current-feedback input circuitry, so unequal input impedance or trace resistance can create gain imbalance and degrade common-mode rejection. Place the gain-setting and feedback components indicated by the manufacturer application diagram near the device, and maintain symmetric grounding around the analog channel.
Do not treat the 250 V maximum input rating as permission to apply arbitrary high-voltage signals without protection. At gain 100, verify the valid input common-mode range, output swing, and external overvoltage behavior for the selected 2.25 V to 18 V supply. Input clamping, series resistance, and fault-current limits may be required. The maximum input specification and the usable operating range are distinct constraints and both must be satisfied.
Place the supply bypass capacitor close to the amplifier’s supply pins and connect it through a short return path to the same analog ground reference used by the signal source. If the source has substantial capacitance, include it in stability and settling analysis rather than relying only on the nominal 200 kHz bandwidth figure. For gain 100, preserve low parasitic capacitance and symmetric routing to avoid degrading the high-gain frequency response.
Estimated power consumption equals the applied supply voltage multiplied by the device’s operating current under the actual load and bias condition. The applicable supply is between 2.25 V and 18 V, but the operating current must be taken from the manufacturer datasheet for the selected condition. Verify that the upstream regulator can support the amplifier, source resistance, protection network, and any attached sensor excitation current without producing unacceptable rail noise or voltage droop.
Choose gain 10 V/V when the signal can be captured with more bandwidth margin or less output amplification. Choose gain 100 V/V when the source signal is small and requires greater sensitivity, but recheck output headroom, input common-mode limits, noise, and settling behavior. The Texas Instruments INA141 datasheet specifies 200 kHz bandwidth at gain 100; that condition should not be generalized to every gain, source impedance, and output-amplitude combination.
Thông tin tuân thủ
RoHS compliance is identified for the INA141 family. The industrial-grade device is not presented as an AEC-Q100-qualified automotive option. Other environmental and material compliance attributes are not established by the cited product information.