Texas Instruments

INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments

MPN: INA240A2PW ✗ انتهى عمره الإنتاجي
-4 V to +80 V Vdss Bidirectional Id 8-pin TSSOP (PW) Package
الحد الأدنى للطلب: 1 |

INA240A2PW نظرة عامة

Texas Instruments INA240A2PW is a bidirectional, precision current-sense amplifier with a gain of 50 V/V, a -4 V to +80 V common-mode voltage range, and an operating temperature range of -40 °C to +125 °C. The device is packaged in an 8-pin TSSOP (PW) package and is designed for high-side or low-side current measurement in systems exposed to fast common-mode transients.

A current-sense amplifier is an instrumentation amplifier that measures the small voltage developed across a current shunt and converts it into an amplified voltage proportional to current. This device belongs to the instrumentation-amplifier and current-sense-amplifier hierarchy, where its differential measurement, low offset voltage, and common-mode rejection improve the accuracy of power, motor, solenoid, and battery monitoring systems.

The A2 gain option provides 50 V/V amplification. The INA240 family operates from a 5.5 V supply and accepts common-mode voltages extending from -4 V to +80 V. Its enhanced PWM rejection is intended to suppress transient disturbance caused by switching power stages, while bidirectional operation allows measurement of positive or negative current without changing the signal path architecture.

The common-mode range and PWM rejection make the INA240A2PW especially useful where the shunt is placed near a motor, actuator, or inductive load. Although the analog output must remain within the amplifier's supply-voltage limits, the input common-mode voltage can move independently across the stated -4 V to +80 V range. This separation between input common-mode capability and output-supply limits is central to correct application design.

Typical uses include DC motor current control, solenoid and actuator monitoring, battery pack current measurement, industrial power conversion, and electronic loads. The precision architecture is also appropriate for systems that must recover a small shunt voltage accurately while rejecting rapidly changing voltages on the sensed power rail.

For layout, route the two shunt connections as a compact, symmetric pair and minimize the area enclosed by those traces. Place the shunt and amplifier input network close together, use a low-value differential filter only where its added noise and settling behavior are acceptable, and terminate the amplifier output according to the ADC or analog front-end requirements.

This page combines the manufacturer lifecycle information, verified distributor records, family-level alternatives, comparison criteria, and application-oriented design guidance for engineers evaluating the INA240A2PW as a current-sense amplifier for industrial and power-conversion systems.

بدائل مباشرة لـ INA240A2PW — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.

اطلب بدائل

INA240A2PW الحدود القصوى والخصائص الكهربائية

Product Type Bidirectional precision current-sense amplifier
Gain 50 V/V
Common-Mode Voltage Range -4 V to +80 V
جهد التغذية 5.5 V maximum
Maximum Input Offset Voltage 25 µV
نطاق درجة حرارة التشغيل -40 °C to +125 °C
العلبة 8-pin TSSOP (PW)
عدد الدبابيس 8 pins
نوع التركيب Surface mount
Current Direction Bidirectional
Sensing Configuration High-side or low-side
نوع الخرج Analog voltage
Circuit Count 1 circuit
PWM Rejection Enhanced
RoHS Compliance ROHS3 compliant

دليل تكوين أطراف INA240A2PW 8-pin tssop (pw)

تكوين الأطراف لـ INA240A2PW (حزمة 8-pin tssop (pw)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 8-pin tssop (pw) لـ INA240A2PW

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ INA240A2PW.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

INA240A2PW مناسب لـ 6 التطبيقs: DC Motor Current Control, Solenoid and Actuator Feedback, Battery Pack Current Monitoring, Industrial Power Converter Control, Electronic Load and Bench Supply, Three-Phase Power Stage Monitoring.

🏭

DC Motor Current Control

The INA240A2PW fits brushed and brushless DC motor feedback because its 50 V/V gain amplifies a small shunt voltage while the -4 V to +80 V common-mode range accommodates a motor supply that changes rapidly. Place the shunt in the high-side power path and route the differential input pair directly to the amplifier. The main design benefit is improved signal use with a compact analog-output interface; the trade-off is that PWM edge energy at the shunt can couple into the measurement, so layout and the amplifier's enhanced PWM rejection must be evaluated together.

⚡

Solenoid and Actuator Feedback

For solenoid, relay, and actuator monitoring, the INA240A2PW can measure current on a supply rail up to +80 V common-mode without requiring the sensed voltage to remain near the amplifier supply. Its 50 V/V gain converts a millivolt-scale shunt differential into a voltage suitable for an ADC or control loop. Bidirectional sensing supports both energization and transient return current, while the low 25 µV maximum input offset helps preserve accuracy at low current. Keep the shunt connection short and avoid routing input traces parallel to motor-switching edges.

🔋

Battery Pack Current Monitoring

The INA240A2PW is appropriate for battery charge, discharge, and over-current monitoring where the common-mode voltage can substantially exceed the 5.5 V amplifier supply. A shunt placed in the high-side battery path produces a differential voltage proportional to current, and the 50 V/V gain provides useful ADC resolution without requiring a high-voltage signal-conditioning amplifier. Bidirectional operation simplifies charge and discharge measurement. Designers must scale the shunt for the maximum current and confirm that the amplifier output remains within its supply-defined range at both current polarities.

⚡

Industrial Power Converter Control

The INA240A2PW can monitor inductor or MOSFET current in industrial power-conversion circuits because it tolerates a -4 V to +80 V common-mode range and is designed for systems with fast common-mode transients. The 50 V/V gain reduces the required shunt resistance for a given output signal, while the analog output simplifies closed-loop current control. Input filtering may be added for EMI control, but component values should be selected to avoid excessive differential-input capacitance or an unacceptable response delay during current transitions.

🖥️

Electronic Load and Bench Supply

For electronic loads, programmable supplies, and test systems, the INA240A2PW offers precise 50 V/V current amplification with bidirectional operation. It can sense current on either polarity and across a broad common-mode range, making the output easier to condition than a raw millivolt shunt signal. Use the offset limit, gain error, and output range when establishing measurement uncertainty. A Kelvin connection to the shunt minimizes trace resistance errors, particularly when the application requires accurate current measurements at low shunt voltage.

🔌

Three-Phase Power Stage Monitoring

The INA240A2PW can monitor a low-side shunt in a three-phase inverter because its -4 V common-mode capability accommodates a ground-referenced shunt position and its PWM rejection helps attenuate switching disturbance. The 50 V/V gain provides a direct analog measurement for protection or diagnostics. Place each shunt close to its amplifier to minimize inductive pickup, keep high-current switching loops away from the input pair, and verify that the output remains valid during the highest expected transient and fault current.

ملخص المنتجات الموصى بها

INA240A2PWR Same electrical configuration in a tape-and-reel ordering option يُستخدم في: DC Motor Current Control, Solenoid and Actuator Feedback, Battery Pack Current Monitoring, Industrial Power Converter Control, Electronic Load and Bench Supply, Three-Phase Power Stage Monitoring INA240A1PW Texas Instruments يُستخدم في: DC Motor Current Control, Solenoid and Actuator Feedback, Battery Pack Current Monitoring, Industrial Power Converter Control, Electronic Load and Bench Supply, Three-Phase Power Stage Monitoring
What is the operating voltage of INA240A2PW?
The INA240A2PW operates from a 5.5 V supply and supports an input common-mode range of -4 V to +80 V. According to the Texas Instruments INA240 manufacturer datasheet, Rev. C, the common-mode input range is independent of the low-voltage supply used to power the amplifier and output circuitry. The shunt-derived differential signal must remain within the amplifier's specified input limits.
What is the gain of INA240A2PW?
The INA240A2PW has a fixed gain of 50 V/V. Thus, a 10 mV differential shunt voltage produces an ideal output change of 500 mV relative to the output reference. The gain is identified by the A2 suffix in the family ordering information and is distinct from the other INA240 gain options.
Where to download the INA240A2PW datasheet PDF?
The official INA240A2PW datasheet is available through the Texas Instruments product page at https://www.ti.com/product/INA240/part-details/INA240A2PW. The manufacturer identifies the family document as the INA240 datasheet, Rev. C. Use that document for the complete pin description, electrical limits, typical performance curves, application circuit, and package drawings.
Where can I find the INA240A2PW pinout?
The INA240A2PW pinout is shown in the pin-configuration section of the Texas Instruments INA240 manufacturer datasheet, Rev. C. The device uses an 8-pin TSSOP (PW) package. Use the datasheet's pin-description table to assign supply, ground, reference, input, and output functions because the exposed package drawings alone do not communicate the complete functional pin map.
Is INA240A2PW suitable for motor and solenoid control?
Yes, INA240A2PW is suitable for motor and solenoid current feedback because it supports a -4 V to +80 V common-mode range and enhanced PWM rejection. Its 50 V/V gain amplifies small shunt voltages, while bidirectional operation accommodates positive and negative current. The system must still keep the amplifier supply and output within their specified limits.
What is the best drop-in replacement for INA240A2PW?
No alternative was confirmed as a fully qualified drop-in replacement for INA240A2PW. INA240A2PWR has the same electrical ordering code but uses a different shipping format, so it is a packaging alternative rather than a distinct engineering substitute. INA240A1PW changes the gain from 50 V/V to 20 V/V and therefore cannot replace the target without circuit changes.
Can INA240A2PWR replace INA240A2PW?
INA240A2PWR can provide the same INA240A2 electrical configuration and 8-pin TSSOP footprint, but it represents the tape-and-reel ordering option rather than the target's original tube format. Engineers should confirm the manufacturer's lifecycle and ordering information for the exact suffix before treating it as a sourcing replacement. No different gain option is electrically interchangeable without recalibration.
INA240A2PW vs INA240A3PWR - which is better for motor control?
Choose INA240A2PW when a 50 V/V gain and lower output-swing requirement are preferable, and choose INA240A3PWR when its higher gain produces a larger output signal from the same shunt voltage. The two devices are not direct drop-in substitutes for an unchanged design because their gain settings differ. Select the gain by calculating the required output range across minimum and maximum load current.
When should I choose INA240A2PW over INA240A1PW?
Choose INA240A2PW when the shunt signal is small enough to require 50 V/V rather than 20 V/V. The higher gain improves signal utilization but also increases the output voltage change and reduces the remaining output headroom. Choose INA240A1PW when a larger shunt voltage or more analog-output range is required and 20 V/V still meets the resolution target.
Is INA240A2PW suitable for high-side current sensing?
Yes, INA240A2PW supports high-side sensing with a common-mode voltage range of -4 V to +80 V. Place the shunt in the positive supply path and connect the amplifier inputs across it with the correct polarity. Bidirectional operation means the output can move above or below its reference, provided the resulting signal remains inside the output range.
What are the key specifications of INA240A2PW that engineers should know?
The principal INA240A2PW specifications are 50 V/V gain, a -4 V to +80 V common-mode range, 5.5 V maximum supply voltage, 25 µV maximum input offset voltage, and operation from -40 °C to +125 °C. It is a bidirectional analog-output amplifier in an 8-pin TSSOP (PW), with enhanced PWM rejection for switched-power and motor systems.
How should I design the shunt and input layout for INA240A2PW?
Route the INA240 and INA− connections as a short, closely coupled differential pair directly from the shunt pads to the amplifier. Keep the loop area small, connect the return path consistently with the power ground, and avoid switching nodes beneath the sensitive pair. Place optional input filtering close to the device and verify that filtering does not compromise the required response and noise performance.
What is the lifecycle status of INA240A2PW?
Texas Instruments lists INA240A2PW as no longer in production. The exact suffix and associated INA240 ordering variants should be checked before committing a new design, especially when the required packaging differs. A family member may remain available even after one package or shipping option reaches end of production.
Where can I buy INA240A2PW and check current lead time?
Use the Request a Quote form on this page to request current availability, unit pricing, minimum order quantity, and lead time for INA240A2PW. Because the manufacturer identifies this exact ordering option as no longer in production, a quotation is preferable to assuming stock or an interchangeable active suffix. Confirm the final manufacturer part number before releasing a purchase order.
What is the best INA190A2 equivalent for INA240A2PW?
INA190A2 is a possible functional alternative with 50 V/V gain, but it is not confirmed here as a pin-for-pin TSSOP replacement for INA240A2PW. Its common-mode capability is reported as 40 V versus 80 V for INA240A2, so it cannot handle the same bus voltage. Validate package, pinout, common-mode range, transient response, and output limits before using it as a second source.

بيانات مرجعية هندسية لـ INA240A2PW — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose INA240A2PW when the design requires a bidirectional 50 V/V current measurement, a sensed common-mode voltage as high as +80 V, and operation across -40 °C to +125 °C. Its combination of low maximum offset voltage and enhanced PWM rejection is useful in motor drives, industrial converters, solenoid controls, and battery systems. INA240A1PW is preferable when the shunt already develops a sufficiently large signal and more analog-output range is needed, but it cannot replace the target without changing gain and recalibrating the signal chain. INA190A2 may be considered functionally when its lower common-mode range is acceptable, although it was not confirmed as a pin-for-pin TSSOP replacement. Because INA240A2PW is listed as no longer in production, confirm lifecycle status and obtain the exact suffix required for new production releases.

المقارنة مع البدائل

المعامل هذا المنتج
Brand Texas Instruments
Package 8-pin TSSOP (PW)
Product Type Bidirectional current-sense amplifier
Gain 50 V/V
Common-Mode Voltage Range -4 V to +80 V
Maximum Supply Voltage 5.5 V
Maximum Input Offset Voltage 25 µV
Operating Temperature Range -40 °C to +125 °C
PWM Rejection Enhanced
Output Type Analog voltage

أبرز الفروقات

  • Wide sensed common-mode range (مقابلINA190A2)
  • Enhanced PWM rejection for switched systems (مقابلINA190A2)
  • Higher gain than INA240A1PW (مقابلINA240A1PW)

ملاحظات التصميم

Route INA and INA− as a short, symmetric differential pair from the shunt to the amplifier. Keep the pair away from switch nodes, gate-drive traces, and high-current return paths. Use a Kelvin connection when shunt accuracy matters: connect each amplifier input directly to its corresponding shunt pad and avoid sharing copper with the power-current path. This minimizes parasitic voltage pickup and preserves the benefit of the device's enhanced PWM rejection.

Do not confuse common-mode range with supply range. The INA240A2PW accepts a -4 V to +80 V sensed common-mode voltage while being powered from a maximum of 5.5 V. Its output must remain within the supply-defined output range. Calculate the output at maximum positive and negative current, including offset and tolerance, before selecting the shunt resistance or adding another gain stage.

If input filtering is required, place the differential filter components close to the amplifier and select their values against the required transient response rather than applying a generic RC network. Capacitance across the differential inputs can alter settling behavior, while unequal filtering can impair common-mode rejection. Validate the completed layout with the switching waveform, including overshoot and ringing at the shunt.

معلومات الامتثال

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

RoHS3 compliance is identified in the product information. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer for the exact ordering option.

تم التحقق من البيانات في: 2026-11-14 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

INA240A2PW datasheet INA240A2PW pinout INA240A2PW datasheet pdf INA240A2PW specifications INA240A2PW common mode voltage INA240A2PW gain INA240A2PW TSSOP-8 INA240A2PW equivalent INA240A2PW replacement INA240A2PW vs INA240A1PW INA240A2PW application circuit INA240A2PW price INA240A2PW stock Texas Instruments INA240A2PW INA240A2PW current sense amplifier

المكونات والمصطلحات ذات الصلة

Texas Instruments INA240A2PW INA240A2PWR INA240A1PW INA190A2 current-sense amplifier instrumentation amplifier bidirectional current measurement high-side current sensing low-side current sensing common-mode voltage power supply rejection ratio PWM rejection input offset voltage shunt resistor analog output TSSOP-8 surface-mount package semiconductor motor control industrial power conversion battery management solenoid feedback
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر