ISL8392IB-T - 4-Channel SPST Analog Switch | Renesas
MPN: ISL8392IB-T ✓ نشطISL8392IB-T نظرة عامة
An analog switch is an integrated semiconductor that routes electrical signals between circuit nodes under digital control. The ISL8392IB-T belongs to the analog switch, multiplexer and demultiplexer hierarchy, where it functions as four independent SPST switches. Compared with mechanical relays, it can switch faster, consume less power, and occupy less circuit-board area. Unlike a multiplexer that combines several inputs onto one output, its 1:1 configuration preserves a separate signal path for every channel.
Low power consumption is a principal feature of the ISL8392IB-T. The manufacturer specifies approximately 1 µW power consumption for battery-powered applications, with maximum leakage current of 2.5 nA. This low leakage helps preserve battery capacity when a switched node is inactive. The four switch channels also provide on-resistance flatness of up to 4 ohms, helping maintain consistent signal behavior across the operating range.
Fast switching makes the part suitable for time-sensitive signal paths. The specified turn-on time is 60 ns and turn-off time is 30 ns. These values are especially useful when the device selects between sensors, measurement channels, communication paths, or test points under digital control. Because analog switches conduct rather than regenerate signals, input bandwidth, on-resistance, capacitance, leakage, and off-state isolation remain important system-level considerations.
Typical uses include battery-powered instrumentation, portable measurement equipment, automated test systems, sample-and-hold front ends, sensor selection circuits, and communication routing. The device can operate from a single supply for low-voltage systems or from dual supplies when bipolar signals must be switched. Its 16-SOIC package supports conventional surface-mount assembly while providing four independently controlled switches in a modest board area.
A practical design should verify the signal amplitude against the selected supply configuration, place decoupling capacitance close to the supply pins, and keep high-speed routes short to minimize parasitic capacitance. Control inputs should be driven only with levels compatible with the operating supply. Check the datasheet pin-description and switching tables before assigning control states or routing a signal through an inactive channel.
بدائل مباشرة لـ ISL8392IB-T — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع ISL8392IB-T (نفس عامل الشكل والبصمة) — يختلف في Dual-Supply Operating Range, Package, Low Power Consumption, Switch Configuration.
ISL8392IB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ISL8392IB-T الحدود القصوى والخصائص الكهربائية
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 |
| Switch Type | Quad SPST |
| Maximum On-Resistance | 35 ohm |
| On-Resistance Flatness | 4 ohm maximum |
| Single-Supply Operating Range | +2 V to +12 V |
| Dual-Supply Operating Range | ±2 V to ±6 V |
| Power Consumption | 1 µW |
| Maximum Leakage Current | 2.5 nA |
| Turn-On Time | 60 ns |
| Turn-Off Time | 30 ns |
| Process Technology | CMOS |
| العلبة | 16-SOIC |
| نوع التركيب | Surface mount |
دليل تكوين أطراف ISL8392IB-T 16-soic
تكوين الأطراف لـ ISL8392IB-T (حزمة 16-soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ISL8392IB-T.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
ISL8392IB-T مناسب لـ 6 التطبيقs: Battery-Powered Portable Measurement, Automated Test and Measurement Routing, Sensor Input Selection, Sample-and-Hold Signal Routing, Communication Signal Routing, Low-Voltage Instrumentation Front End.
Battery-Powered Portable Measurement
The ISL8392IB-T fits portable measurement equipment where four independent analog paths must be selected without placing a substantial load on the battery. Its approximately 1 µW power consumption and 2.5 nA maximum leakage are especially valuable when inactive channels remain connected to high-impedance sensors. The 60 ns turn-on time and 30 ns turn-off time permit rapid range or source selection, while the 35-ohm maximum on-resistance can serve many sensor-level signals when the downstream amplifier provides suitable input impedance and bandwidth.
Automated Test and Measurement Routing
The four SPST channels of the ISL8392IB-T can route test signals among multiple sources, instrument inputs, or DUT nodes under digital control. Fast 60 ns turn-on and 30 ns turn-off transitions shorten the interval between routing commands, making the switch appropriate for repetitive measurement sequences. The 35-ohm maximum on-resistance must be included in the complete signal-path calculation, especially when driving low-impedance instrument front ends. The 16-SOIC package also allows four routing functions to be consolidated on a compact board.
Sensor Input Selection
The ISL8392IB-T can connect one of several sensor outputs to a shared conditioning channel through four independent SPST paths. Its low 2.5 nA maximum leakage helps reduce errors when the selected source has high source impedance, while approximately 1 µW power consumption suits compact sensing platforms. A design should confirm that the selected sensor amplitude remains within the operating limits of the chosen single- or dual-supply configuration. Output buffering may be required when the source impedance interacts significantly with the switch's 35-ohm maximum on-resistance.
Sample-and-Hold Signal Routing
For sampling systems, the ISL8392IB-T can route selected transducer or reference signals toward a sampling capacitor and subsequent converter. Its 30 ns turn-off time and 60 ns turn-on time permit short switching windows, while four independently controlled channels support multiple sources or acquisition paths. Care is required around capacitive loads because parasitic capacitance and charge injection can affect settling accuracy. Place the switch close to the sampling network and use a low-impedance acquisition stage where the 35-ohm on-resistance would otherwise create excessive attenuation.
Communication Signal Routing
The ISL8392IB-T can select among communication or peripheral signal paths when the signals operate within its low-voltage supply range. The fast switching transitions support controlled route changes, and the low 1 µW power figure can help preserve energy in portable systems. Nevertheless, an analog switch does not regenerate the signal, so insertion loss, bandwidth, off-isolation, and crosstalk determine suitability. Use short PCB traces, appropriate return paths, and source/load impedances that do not make the 35-ohm on-resistance the dominant link impedance.
Low-Voltage Instrumentation Front End
The ISL8392IB-T suits low-voltage instrumentation front ends where precision signal paths must be selected while power use remains constrained. Operation from a single +2 V to +12 V supply accommodates compact systems, while the dual ±2 V to ±6 V option supports bipolar signal routing. Four independent SPST channels provide local multiplexing without using a broader multiplexer topology. The design should account for signal-swing limits, control-logic levels, leakage into high-impedance nodes, and the attenuation introduced by the 35-ohm maximum on-resistance.
بيانات مرجعية هندسية لـ ISL8392IB-T — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Brand | Renesas Electronics |
| Package | 16-SOIC |
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 |
| Switch Type | Quad SPST |
| Maximum On-Resistance | 35 ohm |
| Single-Supply Operating Range | +2 V to +12 V |
| Dual-Supply Operating Range | ±2 V to ±6 V |
| Power Consumption | 1 µW |
| Maximum Leakage Current | 2.5 nA |
| Turn-On Time | 60 ns |
| Turn-Off Time | 30 ns |
أبرز الفروقات
- Combines four independently controlled analog paths in one device (مقابلDiscrete SPST switch implementations)
- Low power is suitable for portable and battery-operated systems (مقابلConventional higher-leakage analog switches)
- Fast switching supports time-sensitive routing (مقابلMechanically operated relays)
- Supports both unipolar and bipolar operating arrangements (مقابلSingle-supply-only analog switches)
ملاحظات التصميم
Treat the 35-ohm maximum on-resistance as part of the complete signal-path impedance. With a switch resistance of 35 ohms and a 50-ohm source impedance, the closed-channel attenuation is approximately -3.9 dB before considering capacitance or bandwidth. Use a higher source impedance or a suitable buffer when full-amplitude transfer is required, and evaluate the total RON flatness of up to 4 ohms across the intended operating conditions.
Place the device close to the signals being routed and connect its supply pins to short, low-impedance decoupling paths. Keep analog terminals away from fast control and clock traces to reduce capacitive coupling. Provide a continuous ground reference beneath the SOIC footprint and avoid routing high-current or high-voltage paths adjacent to sensitive analog terminals. These layout practices help preserve the intended switching behavior and reduce off-state feedthrough.
Select the supply configuration according to both the control-logic levels and the analog signal range. A single +2 V to +12 V supply simplifies low-voltage systems, while ±2 V to ±6 V permits bipolar routing. Ensure every driven control input remains within its valid logic level and that signal excursions do not exceed the operating limits in the manufacturer datasheet. Decouple the supply locally and verify startup states before enabling sensitive downstream equipment.
Do not assume that the fast 60 ns turn-on and 30 ns turn-off specifications guarantee complete settling at every load. Capacitive probe capacitance, long PCB traces, slow control edges, and high source impedances can extend practical settling time. Likewise, approximately 1 µW power consumption is a device-level figure rather than a guarantee of total system consumption. Re-evaluate leakage through the switch, pull resistors, external drivers, and connected circuitry in battery-operated designs.
معلومات الامتثال
The manufacturer product page and component listings do not explicitly state the requested RoHS, REACH, lead-free, halogen-free, or conflict-minerals statuses. AEC-Q100 qualification is not indicated for this general-purpose interface switch.