Renesas Electronics

ISL8483IB-T - Half-Duplex RS-422/RS-485 Transceiver | Renesas

MPN: ISL8483IB-T ✓ نشط
RS-422 and RS-485 Rds(on) 8-pin SOIC Package
الحد الأدنى للطلب: 1 |

ISL8483IB-T نظرة عامة

Renesas Electronics ISL8483IB-T is a single-channel, half-duplex interface transceiver supporting RS-422 and RS-485 communications in an 8-pin SOIC package. The device combines one driver and one receiver in a compact package, making it suitable for bidirectional industrial data links where both transmitting and receiving functions are required on the same bus.

A half-duplex RS-422/RS-485 transceiver is a physical-layer interface IC that converts digital logic-level signals into differential bus signals and converts received differential signals back into logic levels. Within the interface hierarchy, the ISL8483IB-T belongs to the transceiver class of interface ICs, combining an RS-422/RS-485 driver, an RS-422/RS-485 receiver, and bus-facing control functions in one package. Differential signaling supports reliable communication over longer cable runs while reducing sensitivity to common-mode noise.

The verified manufacturer-related listing identifies the ISL8483IB-T as a one-driver, one-receiver, half-duplex RS-422/RS-485 transceiver in an 8-SOIC package. Its principal engineering benefits are component consolidation, a compact surface-mount footprint, and support for both RS-422 and RS-485 point-to-point networks. The single driver and receiver arrangement also helps designers manage bus direction explicitly in half-duplex systems.

The part is appropriate for industrial controllers, factory automation equipment, remote sensor interfaces, and embedded communications modules. In these systems, the transceiver connects a host UART or programmable controller to a differential bus while converting logic signals to and from the physical network. The 8-pin SOIC package supports conventional PCB assembly methods and is smaller than many legacy through-hole transceiver packages.

Designers should verify the final electrical limits, receiver fail-safe behavior, driver enable polarity, and bus termination requirements against the manufacturer datasheet before releasing production hardware. In half-duplex implementations, correct driver-enable timing is essential to prevent contention, while proper biasing and termination help maintain signal integrity on the RS-422 or RS-485 network.

This page combines the verified Renesas product identity, exact package classification, interface capability, sourcing information, available drop-in references, and practical implementation guidance. It is intended to help engineers identify the correct device, plan PCB connections, and compare compatible RS-422/RS-485 interface options before detailed circuit validation.

بدائل مباشرة لـ ISL8483IB-T — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع ISL8483IB-T (نفس عامل الشكل والبصمة) — يختلف في Package, Product Type, Receiver Count, Supported Standards.

Renesas Electronics
Package: 8-SOIC
Product Type: 1/1 RS-485/RS-422 transceiver
Receiver Count: 1
قارن مع ISL8483IB-T →

ISL8483IBZ-T

✅ بديل مباشر
📦 8-SOIC
No measurable electrical parameter differences were identified, representing 0% difference in the compared primary performance ratings

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8483IB

✅ بديل مباشر
Renesas Electronics
📦 8-SOIC
1/1 RS-485/RS-422 transceiver · 250 kbps · 5 V · Half-duplex · RS-485 and RS-422 · 1 · 1 · Yes

تواصل لمعرفة السعر

عرض ورقة البيانات ←

ISL8483IB-T المواصفات

Product Type RS-422/RS-485 half-duplex transceiver
Channel Count 1 channel
Driver Count 1 driver
Receiver Count 1 receiver
Duplex Mode Half-duplex
Supported Standards RS-422 and RS-485
العلبة 8-pin SOIC
نوع التركيب Surface mount

دليل تكوين أطراف ISL8483IB-T 8-pin soic

تكوين الأطراف لـ ISL8483IB-T (حزمة 8-pin soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 8-pin soic لـ ISL8483IB-T

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ISL8483IB-T.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ISL8483IB-T مناسب لـ 6 التطبيقs: Industrial Controller RS-485 Interface, Factory Automation Sensor Node, Remote Sensor and Telemetry Link, Instrumentation and Measurement Equipment, Building and HVAC Control Module, Embedded Serial Communication Bridge.

🏭

Industrial Controller RS-485 Interface

The ISL8483IB-T fits an industrial controller that must communicate over an RS-485 bus while conserving board area. Its one-driver, one-receiver arrangement provides the physical-layer functions required for bidirectional half-duplex communication, and the 8-SOIC package offers a compact surface-mount footprint. The controller must deassert driver enable before receiving and apply the timing specified in the manufacturer datasheet. RS-485 bus design also requires correct termination at the physical ends of the network and suitable biasing where required.

🏭

Factory Automation Sensor Node

The ISL8483IB-T can connect a compact factory sensor node to a fieldbus-style differential network when the node uses a half-duplex RS-422 or RS-485 physical layer. The single driver and single receiver architecture provides bidirectional communication through one compact 8-SOIC device. Keep the bus connection isolated from noisy motor and relay wiring, use a defined logic state while the driver is disabled, and validate the transceiver against the cable length, baud rate, and termination arrangement used in the installation.

🧩

Remote Sensor and Telemetry Link

The ISL8483IB-T is suitable for a remote telemetry link that exchanges commands and measurements over a differential bus. Half-duplex operation allows the same wiring to support both directions, while the 8-SOIC package keeps the interface compact enough for distributed instrumentation. The receiving software must allow sufficient turnaround time after changing bus direction. At the PCB level, route the differential pair as a tightly coupled pair, keep stubs short, and follow the recommended grounding and protection arrangement for the target installation.

🔧

Instrumentation and Measurement Equipment

The ISL8483IB-T can provide the differential bus interface in laboratory or process instrumentation that must communicate with a host over RS-422 or RS-485. Combining one driver and one receiver in an 8-SOIC package reduces component count compared with separate transmit and receive devices when the bus is operated half-duplex. Use controlled direction timing and verified termination to minimize signal integrity issues. Check the exact input sensitivity, common-mode range, and supply requirements in the manufacturer datasheet before matching it to high-precision front-end circuitry.

🏠

Building and HVAC Control Module

The ISL8483IB-T fits distributed HVAC and building-control modules that communicate with a controller over a wired RS-485 or RS-422 network. Its one-channel half-duplex configuration supports bidirectional command and status exchange, and the small 8-SOIC package leaves space for sensors, relays, and power conversion circuitry. Firmware should enforce a quiet interval and bus turnaround before reversing transmission direction. Protection components and grounding must be selected for the installation environment rather than added solely by signal amplitude.

🌐

Embedded Serial Communication Bridge

The ISL8483IB-T can serve as the differential interface stage in an embedded serial bridge that converts a host UART into RS-422 or RS-485. The 8-SOIC package and integrated one-driver, one-receiver arrangement support a compact implementation without requiring separate driver and receiver ICs. The bridge firmware must manage the enable signal so the transmitter is active only while data is being sent. Add termination, protection, and filtering according to the cable environment, and verify operation at the intended data rate and cable length.

What is the ISL8483IB-T?
The Renesas Electronics ISL8483IB-T is a one-channel, half-duplex transceiver that combines one driver and one receiver for RS-422 and RS-485 communications. According to the Renesas product classification, it is packaged in an 8-pin SOIC. Its compact surface-mount construction and bidirectional bus capability suit compact controller, sensor, and industrial communication modules.
Is the ISL8483IB-T a full-duplex or half-duplex transceiver?
The ISL8483IB-T is a half-duplex RS-422/RS-485 transceiver. It includes one driver and one receiver, allowing the same pair of bus conductors to carry data in either direction, but not simultaneously. According to the Renesas product listing, the device is a one-channel half-duplex interface IC in an 8-SOIC package.
Where can I find the ISL8483IB-T datasheet and pinout?
The ISL8483IB-T datasheet and pin information are available through the Renesas ISL8483 product documentation linked from its official product resources. The manufacturer classification identifies an 8-pin SOIC package. Use the pin-description table and typical application circuit in the manufacturer datasheet when assigning RE, DE, logic-input, ground, and differential bus connections.
What communication standards does ISL8483IB-T support?
The ISL8483IB-T supports both RS-422 and RS-485 differential communication standards. According to the Renesas product description, it is a one-driver, one-receiver half-duplex transceiver in an 8-SOIC package. The protocol implemented by the host controller remains separate from the physical-layer duties handled by this interface IC.
Where can I buy ISL8483IB-T and check its price?
Use the Request a Quote form on this page to request the current ISL8483IB-T unit price, stock status, and lead time. The manufacturer-related listings identify the exact MPN as an 8-SOIC RS-422/RS-485 transceiver, allowing procurement to confirm the correct suffix and package before ordering.
How much does ISL8483IB-T cost?
Current ISL8483IB-T pricing is handled through the Request a Quote form on this page so that the quotation reflects the requested quantity and supply conditions. Do not rely on a generic family price when ordering this part, because the exact ISL8483IB-T suffix and its 8-SOIC configuration must be matched.
Is ISL8483IB-T in stock and what is its lead time?
Current ISL8483IB-T inventory and lead time should be requested through the Request a Quote form on this page. Renesas-related distributor listings identify the exact ISL8483IB-T component and show an active 8-SOIC listing, but transaction-specific availability can vary with quantity, date code, and supply conditions.
What can replace the ISL8483IB-T?
The ISL8483IBZ-T is a documented pin-to-pin alternative to the ISL8483IB-T, with no measurable differences identified across the primary technical parameters in the comparison data. Confirm supply voltage, logic levels, maximum data rate, receiver enable behavior, and bus-pin assignments against the manufacturer datasheet before approving it for production.
Is the ISL8483IB-T the same as the ISL8483IB?
The ISL8483IB and ISL8483IB-T are closely related Renesas designations, but the suffix must be checked before substitution because packaging and orderable-part details can differ. The comparison data reports identical performance profiles for ISL8483IB-T and ISL8483IBZ-T. Confirm the exact ordering code and tape-and-reel or tube configuration with the manufacturer.
ISL8483IB-T vs ISL8483IBZ-T: which is the better drop-in replacement?
The ISL8483IBZ-T is the stronger documented drop-in choice because the comparison data reports identical performance profiles and no measurable parameter differences from the ISL8483IB-T. Both use the same 8-SOIC interface-device classification. Validate production ordering codes and packaging requirements before final release.
When should I choose ISL8483IB-T over another RS-485 transceiver?
Choose the ISL8483IB-T when the design needs a half-duplex RS-422/RS-485 physical layer with one driver, one receiver, and an 8-pin SOIC footprint. Confirm its exact electrical ratings and control logic in the manufacturer datasheet. If an alternative differs in supply voltage, logic levels, enable polarity, or data rate, it should not be treated as a drop-in replacement.
Is ISL8483IB-T suitable for industrial RS-485 equipment?
The ISL8483IB-T is suitable for compact RS-485 interface sections in industrial equipment because it provides one driver and one receiver in an 8-pin SOIC package. Its half-duplex operation suits shared-bus designs with controlled direction. Confirm operating-temperature limits, ESD performance, common-mode range, and isolation requirements before deployment.
How should driver enable timing be handled with ISL8483IB-T?
Driver-enable timing must prevent the transmitter and receiver from driving the bus in conflicting states during direction changes. Use the enable-control and timing definitions in the manufacturer datasheet, and allow the bus driver to return to a high-impedance state before the opposite direction is enabled. Proper termination and biasing also reduce reflections and false transitions.
What are the key specifications of ISL8483IB-T that engineers should know?
The ISL8483IB-T is a one-channel, half-duplex RS-422/RS-485 transceiver with one driver and one receiver in an 8-pin SOIC package. According to the Renesas product classification, its key architecture is a combined differential transmitter and receiver for bidirectional point-to-point buses. Verify supply voltage, data rate, logic levels, and enable polarity against the manufacturer datasheet.
What is the best Maxim equivalent for ISL8483IB-T?
A specific Maxim cross-reference MPN is not identified by the available replacement listing, so no Maxim part can be represented as a confirmed drop-in substitute. Use the Renesas and manufacturer cross-reference tools to identify candidates, then require an exact 8-SOIC footprint and matching supply, logic, data-rate, enable, and bus specifications before substitution.

بيانات مرجعية هندسية لـ ISL8483IB-T — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the ISL8483IB-T for a compact half-duplex RS-422 or RS-485 physical-layer design that needs one driver and one receiver in an 8-SOIC package. It is appropriate for industrial controllers, remote telemetry nodes, instrumentation, HVAC modules, and embedded serial bridges where the host can control bus direction. The ISL8483IBZ-T is the clearest drop-in alternative because the comparison data reports identical primary performance ratings; use it when the exact ordering code, lifecycle status, and production supply have been confirmed. The ISL8483IB is another closely related same-package option, but verify its suffix, tape-and-reel or tube configuration, and ordering documentation before substitution. For any proposed cross-brand replacement, require an exact 8-SOIC footprint plus matching supply voltage, logic levels, data rate, enable polarity, bus-pin assignments, common-mode range, and fail-safe behavior. A shared package alone does not establish drop-in compatibility.

المقارنة مع البدائل

المعامل هذا المنتج ISL8483IBZ-T ISL8483IB
Package 8-SOIC 8-SOIC 8-SOIC
Brand Renesas Electronics Renesas Electronics Renesas Electronics
Transceiver Type RS-422/RS-485 half-duplex transceiver RS-422/RS-485 half-duplex transceiver RS-422/RS-485 transceiver
Channel Count 1 channel 1 channel 1 channel
Driver and Receiver Count 1 driver, 1 receiver 1 driver, 1 receiver 1 driver, 1 receiver
Duplex Mode Half-duplex Half-duplex Half-duplex
Supported Standards RS-422 and RS-485 RS-422 and RS-485 RS-422 and RS-485
Measured Parameter Difference Reference device 0% difference in compared primary performance ratings 0% difference in compared electrical performance

أبرز الفروقات

  • Single-package half-duplex RS-422/RS-485 interface (مقابلISL8483IB)
  • Direct same-family replacement path (مقابلISL8483IBZ-T)
  • Compact 8-SOIC integration (مقابلISL8483IBZ-T)

ملاحظات التصميم

Route the differential bus conductors as a closely coupled pair and minimize stub lengths between the transceiver and connector. Place termination components at the physical endpoints of the bus rather than at every node. For half-duplex operation, verify that the driver is disabled before the receiver path is enabled and that firmware observes an adequate bus-turnaround interval.

Use the manufacturer pin-description table and typical application layout when assigning the 8-SOIC connections. Keep the device-control traces away from the differential bus pair, maintain a continuous ground reference beneath the interface section, and place any decoupling capacitors directly between the appropriate supply and ground pins with short traces. This reduces susceptibility to switching noise and helps preserve a defined bus state.

Do not treat every RS-422 or RS-485 transceiver as a drop-in replacement solely because it uses an 8-SOIC package. Confirm supply voltage, logic thresholds, driver enable polarity, receiver enable polarity, bus impedance, maximum data rate, common-mode range, and fail-safe behavior against the manufacturer datasheet. Also verify whether the network is point-to-point RS-422 or multipoint RS-485 before selecting biasing and protection.

Keep the communication interface physically separated from switching regulators, relays, motors, and high-di/dt traces. If the cable interface is exposed to industrial transients, add protection selected for the installation's surge, ESD, and ground-potential requirements. Maintain a controlled ground strategy so protection currents do not flow through sensitive logic paths or the differential pair.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ISL8483IB-T ordering code. Confirm environmental and quality documentation with Renesas before production release.

تم التحقق من البيانات في: 2026-11-15 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ISL8483IB-T datasheet ISL8483IB-T datasheet pdf ISL8483IB-T pinout ISL8483IB-T equivalent ISL8483IB-T replacement ISL8483IB-T cross reference ISL8483IB-T vs ISL8483IBZ-T Renesas ISL8483IB-T ISL8483IB-T 8-SOIC footprint ISL8483IB-T RS-485 transceiver ISL8483IB-T price ISL8483IB-T stock ISL8483IB-T application circuit ISL8483IB-T schematic

المكونات والمصطلحات ذات الصلة

Renesas Electronics ISL8483IB-T ISL8483IBZ-T ISL8483IB RS-422 RS-485 half-duplex transceiver differential line driver differential line receiver interface IC physical-layer interface serial communications 8-SOIC SOIC package family surface mount industrial automation factory automation remote telemetry HVAC control instrumentation bus termination common-mode noise embedded communications bridge
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر