Renesas Electronics

ISL8485EIB - 5V RS-422/RS-485 Transceiver | Renesas

MPN: ISL8485EIB ✓ نشط
4.5 V to 5.5 V Vdss RS-422 and RS-485 Rds(on) 8-pin SOIC Package
الحد الأدنى للطلب: 1 |

ISL8485EIB نظرة عامة

Renesas Electronics ISL8485EIB is a single-channel, half-duplex RS-422/RS-485 interface transceiver designed for 5 V systems, with a specified 4.5 V to 5.5 V supply range and an 8-pin SOIC package. The device combines a balanced line driver and differential receiver in one compact interface, supporting both RS-422 and RS-485 communication standards.

An RS-485/RS-422 transceiver is an interface IC used to connect a controller, sensor, or communication equipment port to a balanced copper cable. The transceiver converts single-ended logic signals into differential bus signals and converts returning differential signals into a logic-level output. In the broader semiconductor hierarchy, it belongs to interface ICs, where differential transceivers support robust, noise-tolerant data links at relatively low bit rates.

The ISL8485EIB provides ESD protection to ±15 kV on the driver outputs and receiver inputs without latch-up. Its BiCMOS construction supports low-power operation from a 5 V supply, while the high-speed ISL8485E configuration is intended for data rates through approximately 5 Mbps. Driver output short-circuit current limiting and on-chip thermal shutdown help protect the device during bus contention.

The ISL8485 family differs from the slew-rate-limited ISL8483E family through its high-speed edge behavior. The faster transitions increase communication throughput, but they also produce more high-frequency content on the bus. Consequently, cable length, topology, termination, grounding, and electromagnetic compatibility requirements must be evaluated carefully rather than relying only on nominal data rate.

Typical uses include industrial sensor networks, building automation equipment, process-control terminals, instrumentation links, and communication ports that need bidirectional half-duplex operation over a balanced bus. A single transceiver supports one physical bus channel, and multiple devices can be connected to an RS-485 segment when the system designer observes the applicable bus-loading and termination rules.

PCB implementation should provide a solid ground plane, place the transceiver close to the connector or protected interface boundary, and route the balanced pair together with matched geometry. The 4.5 V to 5.5 V supply must remain within tolerance, and decoupling should connect directly to the device power and ground pins. External protection or isolation may still be required when exposed cables exceed the device’s specified ESD environment.

This product page consolidates the electrical envelope, package details, application guidance, and verified drop-in alternatives for the ISL8485EIB. It also highlights the practical distinction between high-speed and slew-rate-limited Renesas transceivers so engineers can choose the interface behavior that best matches their cable, topology, and EMC requirements.

بدائل مباشرة لـ ISL8485EIB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

ISL8485EIBZ

✅ بديل مباشر
📦 8-pin SOIC
Same 5 V RS-422/RS-485 function, 8-pin SOIC footprint, and approximately 5 Mbps data rate; ordering suffix differs with 0% parameter change

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8485EIBZ-T

✅ بديل مباشر
📦 8-pin SOIC
Same 5 V RS-422/RS-485 function, 8-pin SOIC footprint, and approximately 5 Mbps data rate; -T denotes the documented delivery configuration with 0% parameter change

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8485EIB-T

✅ بديل مباشر
📦 8-pin SOIC
Same 5 V RS-422/RS-485 family and 8-pin SOIC footprint; -T is the tape-and-reel ordering form with 0% electrical parameter change

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8483EIBZ

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin SOIC
Same 5 V, ±15 kV ESD-protected single-transceiver family and 8-pin SOIC footprint, but slew-rate-limited edges instead of ISL8485E high-speed edges

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8483EIB-T

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin SOIC
Same 5 V, ±15 kV ESD-protected single-transceiver family and 8-pin SOIC footprint, but slew-rate-limited edges instead of ISL8485E high-speed edges

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8485EIB المواصفات

Product Type Single RS-422/RS-485 transceiver
Transceiver Configuration 1 transmitter and 1 receiver
Duplex Mode Half duplex
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Supported Standards RS-422 and RS-485
Process Technology BiCMOS
ESD Protection ±15 kV on driver outputs and receiver inputs
Maximum Data Rate 5 Mbps
Driver Output Protection Short-circuit current limiting
Thermal Protection On-chip thermal shutdown
نطاق درجة حرارة التشغيل -40 °C to +85 °C
العلبة 8-pin SOIC
نوع التركيب Surface mount
Automotive Qualification Not applicable

تكوين أطراف ISL8485EIB

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
دبوس 1 /RE — Receiver enable, active low
دبوس 2 DE — Driver enable, active high
دبوس 3 NC — Not connected
دبوس 4 GND — Ground
دبوس 5 Y — Non-inverting driver output and receiver input
دبوس 6 Z — Inverting driver output and receiver input
دبوس 7 NC — Not connected
دبوس 8 VCC — Positive supply

التطبيقات النموذجية

ISL8485EIB مناسب لـ 6 التطبيقs: Industrial Sensor Networks, Building Automation Equipment, Process-Control Terminals, Instrumentation and Test Equipment, Communication Port Expansion, Data Acquisition Gateways.

🏭

Industrial Sensor Networks

The ISL8485EIB suits balanced half-duplex sensor links operating from a 4.5 V to 5.5 V rail. Its ±15 kV ESD protection helps isolate sensitive receiver and driver pins from cable-borne electrostatic discharge, while short-circuit limiting and thermal shutdown support protection during bus contention. The high-speed ISL8485E behavior can support throughput through approximately 5 Mbps on properly terminated industrial wiring. Designers should place the device near the connector, maintain a continuous ground reference, and evaluate whether additional surge protection is required by the installation’s cable length and exposure.

🏠

Building Automation Equipment

The ISL8485EIB can connect building controllers, room modules, and field interfaces over a differential RS-485 or RS-422 network. Its 5 V operating range tolerates ±10% supply variation, and the integrated ±15 kV ESD protection is valuable at building cable entry points. Half-duplex operation allows the same transceiver to transmit commands and receive sensor or status responses. The design should control DE and RE timing to prevent bus contention, retain the balanced pair’s geometry, and follow the manufacturer’s recommended supply bypassing and termination arrangements.

🔧

Process-Control Terminals

The ISL8485EIB is appropriate for process-control links that connect an instrumentation controller to remote field equipment over copper cabling. The differential interface supports the RS-422 and RS-485 standards, while the 5 V BiCMOS device includes ESD protection without latch-up. Its approximately 5 Mbps capability can shorten transaction times where the cable installation supports that rate. Engineers must still evaluate common-mode range, grounding, cable loss, and the EMC effects of faster driver transitions rather than treating the headline data rate as a guaranteed long-distance specification.

📟

Instrumentation and Test Equipment

The ISL8485EIB can serve as the physical-layer endpoint in laboratory and industrial instrumentation that communicates with a remote fixture or measurement module. Its balanced driver and receiver support reliable signaling over a twisted pair, and the integrated ±15 kV ESD protection improves robustness at the cable boundary. At the board level, the transceiver should be positioned close to the connector while the digital controller remains separated from the analog and switching sections. Correct enable sequencing and controlled driver transitions help avoid data corruption when the instrument changes direction during a measurement sequence.

🌐

Communication Port Expansion

The ISL8485EIB can add a single balanced communication channel to an embedded controller with separate logic-level receive and transmit connections. Because it is a half-duplex single transceiver, firmware must manage direction control and enforce a dead interval between transmit and receive states. The 4.5 V to 5.5 V supply range integrates well with conventional 5 V interface electronics, while ±15 kV ESD protection supports connections to external equipment. For systems requiring multiple bus nodes, each transceiver should connect to the same balanced segment using proper topology, termination, and biasing.

🖥️

Data Acquisition Gateways

The ISL8485EIB can provide a robust wired interface in a data-acquisition gateway that collects information from distributed sensors or subsystems. The RS-422/RS-485 capability permits balanced signaling over longer copper runs than an unprotected single-ended interface, and the device’s ESD protection improves resilience at the gateway boundary. The approximately 5 Mbps high-speed mode can accommodate high-volume telemetry when the physical bus supports it. Designers should isolate high-current or switching circuitry, maintain a low-impedance ground system, and validate termination and isolation against the actual external cable environment.

ملخص المنتجات الموصى بها

ISL8483EIBZ Slew-rate-limited family alternative for slower or EMI-sensitive links يُستخدم في: Industrial Sensor Networks, Process-Control Terminals, Communication Port Expansion ISL8485EIBZ Same-family alternate ordering form يُستخدم في: Industrial Sensor Networks, Process-Control Terminals, Communication Port Expansion ISL8485EIBZ-T Same-family tape-and-reel ordering option يُستخدم في: Building Automation Equipment, Instrumentation and Test Equipment ISL8483EIB-T Slew-rate-limited family option for lower-edge-rate networks يُستخدم في: Building Automation Equipment, Instrumentation and Test Equipment, Data Acquisition Gateways ISL8485EIB-T Same-family tape-and-reel ordering form يُستخدم في: Data Acquisition Gateways
What is the ISL8485EIB?
The ISL8485EIB is a single-channel, half-duplex RS-422/RS-485 interface transceiver operating from a 4.5 V to 5.5 V supply in an 8-pin SOIC package. According to the Renesas manufacturer datasheet for the ISL8483E and ISL8485E families, it combines a balanced driver, differential receiver, BiCMOS circuitry, and ±15 kV ESD protection on communications pins. It is suitable for balanced industrial buses where a single endpoint needs both transmit and receive functions.
What is the operating voltage of ISL8485EIB?
The ISL8485EIB operates from 4.5 V to 5.5 V, which provides ±10% tolerance around a nominal 5 V rail. According to the Renesas manufacturer datasheet for the ISL8483E and ISL8485E families, this supply range is a distinguishing feature of the family. The power design should maintain the voltage within this range under transient loading while placing a local bypass capacitor close to the supply pin.
What data rate does ISL8485EIB support?
The ISL8485EIB supports communication rates through approximately 5 Mbps in its high-speed configuration. The Renesas manufacturer datasheet distinguishes the high-speed ISL8485E from the slew-rate-limited ISL8483E. Maximum practical cable distance is not determined by data rate alone; bus topology, cable characteristics, termination, connector losses, grounding, and electromagnetic compatibility must also be considered.
Is ISL8485EIB suitable for RS-485 applications?
Yes, the ISL8485EIB supports both RS-485 and RS-422 differential communication in a half-duplex configuration. According to the Renesas manufacturer datasheet, each driver output and receiver input is protected against ±15 kV ESD strikes without latch-up. For an RS-485 network, the design must still provide correct bus termination, biasing where required, controlled driver enable timing, and adequate common-mode margin.
Where can I download the ISL8485EIB datasheet PDF?
The official Renesas datasheet for the ISL8483E and ISL8485E family is available through the manufacturer’s document page linked on this product page. The ISL8485EIB-specific technical information is organized in the same family document, including supply limits, ESD ratings, driver and receiver behavior, timing, and package details. Use the Renesas document rather than a distributor summary when assigning PCB pins or calculating system margins.
Where can I find the ISL8485EIB pinout?
The ISL8485EIB uses an 8-pin SOIC package with the receiver enable, driver enable, receive outputs, transmit inputs, supply, and ground connections identified in the Renesas manufacturer datasheet. Use the pin-description table and package drawing when assigning PCB tracks. The exposed connection naming must be checked against the exact ordering code because enable polarity and no-connect assignments are essential to correct half-duplex operation.
What can replace the ISL8485EIB?
The ISL8485EIBZ and ISL8485EIBZ-T are identified as complete drop-in replacements with the same SOIC-8 package, terminals, and principal performance characteristics. Cross-reference information also identifies the corresponding ISL8485EIB-T ordering form. Before substitution, confirm the exact ordering suffix, temperature grade, delivery configuration, supply range, data rate, enable logic, and ESD rating in the manufacturer datasheet.
What is the best drop-in replacement for ISL8485EIB?
The ISL8485EIBZ is the closest documented drop-in option because it uses the same 8-pin SOIC package and is reported as a complete replacement with consistent terminals and performance. The ISL8485EIBZ-T provides the corresponding tape-and-reel ordering configuration. Package equivalence alone is insufficient for final approval, so verify the manufacturer ordering information, pin functions, electrical limits, and qualification requirements for the target assembly.
Is ISL8485EIB the same as ISL8485EIBZ?
The ISL8485EIB and ISL8485EIBZ share the same core RS-485/RS-485 transceiver function and 8-pin SOIC package, and cross-reference information describes the latter as a complete replacement. The ordering suffixes can differ in packaging or compliance-related ordering conventions, so engineers should confirm the manufacturer’s ordering table for their procurement configuration. PCB compatibility does not eliminate the need to check temperature and lifecycle requirements.
ISL8485EIB vs ISL8483E - which is better for long cables?
The ISL8485E is generally preferable when high throughput is required because it uses high-speed driver behavior, while the ISL8483E uses slew-rate-limited edges. Faster edges can increase high-frequency bus content and EMI sensitivity, whereas slew-rate limiting can improve tolerance of some slower, longer cable installations. The better choice depends on cable length, topology, data rate, termination, grounding, and the system EMC target.
When should I choose ISL8485EIB over ISL8483E?
Choose the ISL8485EIB when a half-duplex RS-422 or RS-485 link needs the high-speed behavior associated with the ISL8485E family and data rates through approximately 5 Mbps. Choose the slew-rate-limited ISL8483E family when lower-edge-rate signaling better suits the installed cable or reduces unwanted high-frequency content. Both belong to the Renesas 5 V, ±15 kV ESD-protected transceiver family, but their edge behavior should match the physical channel.
Is ISL8485EIB suitable for industrial sensor networks?
The ISL8485EIB is suitable for industrial sensor networks that use a balanced half-duplex bus and a 4.5 V to 5.5 V supply. Its ±15 kV ESD protection, short-circuit current limiting, and thermal shutdown improve robustness at a protected cable boundary. Industrial implementations should still include connector-level surge protection, controlled grounding, proper cable termination, and verified isolation when the installation exposes the interface to larger transients.
How should ISL8485EIB be laid out on a PCB?
Place the ISL8485EIB close to the connector or protected interface boundary, connect its bypass capacitor directly to the supply and ground pins, and route the differential pair together with consistent geometry. According to the Renesas manufacturer datasheet, the device uses a balanced differential interface. Keep the bus pair away from switching nodes and clocks, provide a continuous ground reference, and verify that external protection does not degrade the intended ESD and signal-integrity performance.
Does ISL8485EIB protect against bus contention?
The ISL8485EIB includes driver output short-circuit current limits and on-chip thermal shutdown intended to withstand RS-485 bus contention without damage. According to the Renesas manufacturer datasheet, these protections address the requirement that drivers survive worst-case bus contention. They do not eliminate application-level contention, so firmware should avoid simultaneous active drivers and include a safe state for the driver-enable control.
Where can I buy ISL8485EIB and what is its lead time?
Use the “Request a Quote” form on this page to ask for ISL8485EIB availability, current lead time, and minimum order quantity. The Renesas manufacturer documentation identifies the device as part of the ISL8485E interface family, while procurement conditions can change by ordering suffix and regional inventory. Quote requests allow the current package, quantity, and delivery requirements to be checked before design release.

بيانات مرجعية هندسية لـ ISL8485EIB — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the ISL8485EIB for a 5 V, half-duplex RS-422 or RS-485 link that benefits from high-speed operation through approximately 5 Mbps and needs ±15 kV ESD-protected communications pins. The ISL8485EIBZ and ISL8485EIBZ-T are appropriate when procurement requires an alternate documented ordering form; both retain the same 8-pin SOIC footprint and core electrical behavior, but the manufacturer ordering table should be checked for packaging and lifecycle details. The ISL8485EIB-T is useful when a tape-and-reel production configuration is required. Consider the ISL8483EIBZ or ISL8483EIB-T when slew-rate-limited edges are preferable for EMI or cable behavior, accepting that their lower-edge-rate operation can limit throughput. Verify enable polarity, exact data-rate limits, temperature grade, and lifecycle status against the manufacturer datasheet before releasing a substitution.

المقارنة مع البدائل

المعامل هذا المنتج ISL8485EIBZ ISL8485EIBZ-T ISL8485EIB-T ISL8483EIBZ ISL8483EIB-T
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Product Type Single half-duplex RS-422/RS-485 transceiver Single half-duplex RS-422/RS-485 transceiver Single half-duplex RS-422/RS-485 transceiver Single half-duplex RS-422/RS-485 transceiver Single half-duplex RS-422/RS-485 transceiver Single half-duplex RS-422/RS-485 transceiver
Supply Voltage 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
ESD Protection ±15 kV ±15 kV ±15 kV ±15 kV ±15 kV ±15 kV
Driver Edge Behavior High speed High speed High speed High speed Slew-rate limited Slew-rate limited
Driver Protection Short-circuit current limiting and thermal shutdown Short-circuit current limiting and thermal shutdown Short-circuit current limiting and thermal shutdown Short-circuit current limiting and thermal shutdown Short-circuit current limiting and thermal shutdown Short-circuit current limiting and thermal shutdown
Special Feature BiCMOS, low-power 5 V operation BiCMOS, low-power 5 V operation BiCMOS, low-power 5 V operation BiCMOS, low-power 5 V operation BiCMOS, low-power 5 V operation BiCMOS, low-power 5 V operation

أبرز الفروقات

  • Documented complete replacement with no PCB change (مقابلISL8485EIBZ)
  • Production-oriented ordering form (مقابلISL8485EIBZ-T)
  • Slew-rate-controlled fallback for EMI-sensitive channels (مقابلISL8483EIBZ)

ملاحظات التصميم

Place the ISL8485EIB close to the cable connector or protected communications boundary. Keep the Y and Z differential pair together, use consistent spacing and via geometry, and provide a continuous ground plane beneath the route. Separate the pair from switching nodes, clocks, and high-current power paths. Place the local supply bypass capacitor directly between VCC and GND, with its ground return connected to the device ground pin without a long loop.

Do not allow the receiver and driver to be enabled in conflicting states. ISL8485EIB is a half-duplex interface, so DE and /RE timing must be managed by the controller and any external logic. Add a deliberate dead interval before changing bus direction, and ensure firmware cannot leave multiple nodes driving the bus simultaneously. The device’s short-circuit limiting and thermal shutdown provide fault protection, but they do not replace correct application-level arbitration.

The high-speed ISL8485E driver transitions can place substantial high-frequency energy onto the balanced pair. Use twisted-pair cable, proper termination, a low-impedance ground system, and the smallest practical enclosure-to-ground distance. If replacing the ISL8485E with the slew-rate-limited ISL8483E family, revalidate timing and EMI performance because the slower edge rate changes the cable spectrum even though the supply voltage and ESD-protection class remain comparable.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The product is a general-purpose interface IC; AEC-Q100 automotive qualification is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the referenced product and manufacturer information.

تم التحقق من البيانات في: 2026-11-20 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ISL8485EIB datasheet ISL8485EIB datasheet pdf ISL8485EIB pinout ISL8485EIB equivalent ISL8485EIB replacement ISL8485EIB cross reference Renesas ISL8485EIB ISL8485EIB 5V RS-485 transceiver ISL8485EIB 8-SOIC ISL8485EIB vs ISL8483E ISL8485EIB price ISL8485EIB stock

المكونات والمصطلحات ذات الصلة

Renesas Electronics ISL8485EIB ISL8485EIBZ ISL8485EIBZ-T ISL8485EIB-T ISL8483EIBZ ISL8483EIB-T RS-422 RS-485 half-duplex transceiver differential line driver differential receiver BiCMOS ESD protection SOIC-8 surface-mount package 5 V power supply 5 Mbps data rate slew-rate-limited driver bus contention protection thermal shutdown short-circuit current limiting industrial communication building automation process control
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر