ISL8485EIB - 5V RS-422/RS-485 Transceiver | Renesas
Référence : ISL8485EIB ✓ ActifISL8485EIB Présentation
An RS-485/RS-422 transceiver is an interface IC used to connect a controller, sensor, or communication equipment port to a balanced copper cable. The transceiver converts single-ended logic signals into differential bus signals and converts returning differential signals into a logic-level output. In the broader semiconductor hierarchy, it belongs to interface ICs, where differential transceivers support robust, noise-tolerant data links at relatively low bit rates.
The ISL8485EIB provides ESD protection to ±15 kV on the driver outputs and receiver inputs without latch-up. Its BiCMOS construction supports low-power operation from a 5 V supply, while the high-speed ISL8485E configuration is intended for data rates through approximately 5 Mbps. Driver output short-circuit current limiting and on-chip thermal shutdown help protect the device during bus contention.
The ISL8485 family differs from the slew-rate-limited ISL8483E family through its high-speed edge behavior. The faster transitions increase communication throughput, but they also produce more high-frequency content on the bus. Consequently, cable length, topology, termination, grounding, and electromagnetic compatibility requirements must be evaluated carefully rather than relying only on nominal data rate.
Typical uses include industrial sensor networks, building automation equipment, process-control terminals, instrumentation links, and communication ports that need bidirectional half-duplex operation over a balanced bus. A single transceiver supports one physical bus channel, and multiple devices can be connected to an RS-485 segment when the system designer observes the applicable bus-loading and termination rules.
PCB implementation should provide a solid ground plane, place the transceiver close to the connector or protected interface boundary, and route the balanced pair together with matched geometry. The 4.5 V to 5.5 V supply must remain within tolerance, and decoupling should connect directly to the device power and ground pins. External protection or isolation may still be required when exposed cables exceed the device’s specified ESD environment.
This product page consolidates the electrical envelope, package details, application guidance, and verified drop-in alternatives for the ISL8485EIB. It also highlights the practical distinction between high-speed and slew-rate-limited Renesas transceivers so engineers can choose the interface behavior that best matches their cable, topology, and EMC requirements.
Alternatives de remplacement direct pour ISL8485EIB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
ISL8485EIBZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL8485EIBZ-T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL8485EIB-T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL8483EIBZ
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
ISL8483EIB-T
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
ISL8485EIB Spécifications
| Product Type | Single RS-422/RS-485 transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| Duplex Mode | Half duplex |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Supported Standards | RS-422 and RS-485 |
| Process Technology | BiCMOS |
| ESD Protection | ±15 kV on driver outputs and receiver inputs |
| Maximum Data Rate | 5 Mbps |
| Driver Output Protection | Short-circuit current limiting |
| Thermal Protection | On-chip thermal shutdown |
| Plage de température de fonctionnement | -40 °C to +85 °C |
| Boîtier | 8-pin SOIC |
| Type de montage | Surface mount |
| Automotive Qualification | Not applicable |
Configuration des broches de ISL8485EIB
| Broche 1 | /RE — Receiver enable, active low |
| Broche 2 | DE — Driver enable, active high |
| Broche 3 | NC — Not connected |
| Broche 4 | GND — Ground |
| Broche 5 | Y — Non-inverting driver output and receiver input |
| Broche 6 | Z — Inverting driver output and receiver input |
| Broche 7 | NC — Not connected |
| Broche 8 | VCC — Positive supply |
Applications typiques
ISL8485EIB convient pour 6 applications: Industrial Sensor Networks, Building Automation Equipment, Process-Control Terminals, Instrumentation and Test Equipment, Communication Port Expansion, Data Acquisition Gateways.
Industrial Sensor Networks
The ISL8485EIB suits balanced half-duplex sensor links operating from a 4.5 V to 5.5 V rail. Its ±15 kV ESD protection helps isolate sensitive receiver and driver pins from cable-borne electrostatic discharge, while short-circuit limiting and thermal shutdown support protection during bus contention. The high-speed ISL8485E behavior can support throughput through approximately 5 Mbps on properly terminated industrial wiring. Designers should place the device near the connector, maintain a continuous ground reference, and evaluate whether additional surge protection is required by the installation’s cable length and exposure.
Recommandé
Building Automation Equipment
The ISL8485EIB can connect building controllers, room modules, and field interfaces over a differential RS-485 or RS-422 network. Its 5 V operating range tolerates ±10% supply variation, and the integrated ±15 kV ESD protection is valuable at building cable entry points. Half-duplex operation allows the same transceiver to transmit commands and receive sensor or status responses. The design should control DE and RE timing to prevent bus contention, retain the balanced pair’s geometry, and follow the manufacturer’s recommended supply bypassing and termination arrangements.
Recommandé
Process-Control Terminals
The ISL8485EIB is appropriate for process-control links that connect an instrumentation controller to remote field equipment over copper cabling. The differential interface supports the RS-422 and RS-485 standards, while the 5 V BiCMOS device includes ESD protection without latch-up. Its approximately 5 Mbps capability can shorten transaction times where the cable installation supports that rate. Engineers must still evaluate common-mode range, grounding, cable loss, and the EMC effects of faster driver transitions rather than treating the headline data rate as a guaranteed long-distance specification.
Recommandé
Instrumentation and Test Equipment
The ISL8485EIB can serve as the physical-layer endpoint in laboratory and industrial instrumentation that communicates with a remote fixture or measurement module. Its balanced driver and receiver support reliable signaling over a twisted pair, and the integrated ±15 kV ESD protection improves robustness at the cable boundary. At the board level, the transceiver should be positioned close to the connector while the digital controller remains separated from the analog and switching sections. Correct enable sequencing and controlled driver transitions help avoid data corruption when the instrument changes direction during a measurement sequence.
Recommandé
Communication Port Expansion
The ISL8485EIB can add a single balanced communication channel to an embedded controller with separate logic-level receive and transmit connections. Because it is a half-duplex single transceiver, firmware must manage direction control and enforce a dead interval between transmit and receive states. The 4.5 V to 5.5 V supply range integrates well with conventional 5 V interface electronics, while ±15 kV ESD protection supports connections to external equipment. For systems requiring multiple bus nodes, each transceiver should connect to the same balanced segment using proper topology, termination, and biasing.
Recommandé
Data Acquisition Gateways
The ISL8485EIB can provide a robust wired interface in a data-acquisition gateway that collects information from distributed sensors or subsystems. The RS-422/RS-485 capability permits balanced signaling over longer copper runs than an unprotected single-ended interface, and the device’s ESD protection improves resilience at the gateway boundary. The approximately 5 Mbps high-speed mode can accommodate high-volume telemetry when the physical bus supports it. Designers should isolate high-current or switching circuitry, maintain a low-impedance ground system, and validate termination and isolation against the actual external cable environment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ISL8485EIB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ISL8485EIBZ | ISL8485EIBZ-T | ISL8485EIB-T | ISL8483EIBZ | ISL8483EIB-T |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Product Type | Single half-duplex RS-422/RS-485 transceiver | Single half-duplex RS-422/RS-485 transceiver | Single half-duplex RS-422/RS-485 transceiver | Single half-duplex RS-422/RS-485 transceiver | Single half-duplex RS-422/RS-485 transceiver | Single half-duplex RS-422/RS-485 transceiver |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV | ±15 kV | ±15 kV | ±15 kV |
| Driver Edge Behavior | High speed | High speed | High speed | High speed | Slew-rate limited | Slew-rate limited |
| Driver Protection | Short-circuit current limiting and thermal shutdown | Short-circuit current limiting and thermal shutdown | Short-circuit current limiting and thermal shutdown | Short-circuit current limiting and thermal shutdown | Short-circuit current limiting and thermal shutdown | Short-circuit current limiting and thermal shutdown |
| Special Feature | BiCMOS, low-power 5 V operation | BiCMOS, low-power 5 V operation | BiCMOS, low-power 5 V operation | BiCMOS, low-power 5 V operation | BiCMOS, low-power 5 V operation | BiCMOS, low-power 5 V operation |
Principaux différenciateurs
- Documented complete replacement with no PCB change (vs ISL8485EIBZ)
- Production-oriented ordering form (vs ISL8485EIBZ-T)
- Slew-rate-controlled fallback for EMI-sensitive channels (vs ISL8483EIBZ)
Notes de conception
Place the ISL8485EIB close to the cable connector or protected communications boundary. Keep the Y and Z differential pair together, use consistent spacing and via geometry, and provide a continuous ground plane beneath the route. Separate the pair from switching nodes, clocks, and high-current power paths. Place the local supply bypass capacitor directly between VCC and GND, with its ground return connected to the device ground pin without a long loop.
Do not allow the receiver and driver to be enabled in conflicting states. ISL8485EIB is a half-duplex interface, so DE and /RE timing must be managed by the controller and any external logic. Add a deliberate dead interval before changing bus direction, and ensure firmware cannot leave multiple nodes driving the bus simultaneously. The device’s short-circuit limiting and thermal shutdown provide fault protection, but they do not replace correct application-level arbitration.
The high-speed ISL8485E driver transitions can place substantial high-frequency energy onto the balanced pair. Use twisted-pair cable, proper termination, a low-impedance ground system, and the smallest practical enclosure-to-ground distance. If replacing the ISL8485E with the slew-rate-limited ISL8483E family, revalidate timing and EMI performance because the slower edge rate changes the cable spectrum even though the supply voltage and ESD-protection class remain comparable.
Informations de conformité
The product is a general-purpose interface IC; AEC-Q100 automotive qualification is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the referenced product and manufacturer information.