KSZ8895FQXI - 5-Port 10/100 Managed Ethernet Switch | Microchip Technology
MPN: KSZ8895FQXI ✓ نشطKSZ8895FQXI نظرة عامة
An Ethernet switch is a Layer 2 networking semiconductor that receives Ethernet frames on one port and forwards them to the appropriate destination port using MAC-address information. The KSZ8895 belongs to the broader hierarchy of Ethernet interface controllers, network switches, Layer 2 devices, and integrated network semiconductors. Its managed architecture allows a host processor or network controller to configure port behavior, while its MII and RMII interfaces support integration with embedded processors, field-programmable gate arrays, application processors, and industrial controllers.
The KSZ8895FQXI provides five integrated 10/100 Ethernet ports, MII and RMII connectivity, and a single 3.3 V operating voltage. Its 128-PQFP 14 x 20 mm package exposes the switch, copper-physical-layer, control, management, clock, and power interfaces through 128 contacts. The automotive qualification indicated by Microchip makes the device relevant to vehicle-network designs as well as industrial, communications, and embedded applications requiring a compact managed Ethernet switch. A single-chip switching design can also reduce board area, external PHY count, and system-level assembly complexity.
Microchip's integrated 10/100 Ethernet-switch implementation combines the 100BASE-TX drivers and 10BASE-T drivers so both can use the same magnetics. The 10BASE-T driver is incorporated into the 100BASE-T driver, with internally wave-shaped and pre-emphasized outputs having a typical 2.3 V amplitude. This integration supports shared copper-magnetics designs while preserving separate logical support for 10 Mb/s and 100 Mb/s operation. Management features are included at the Layer 2 level rather than requiring a separate switch controller for basic port management.
Typical applications include automotive infotainment and in-vehicle networking, industrial Ethernet gateways, factory automation controllers, building-automation equipment, communications equipment, and embedded systems that need several 10/100 ports behind one processor interface. MII is useful when the connected host requires parallel data and control signals, while RMII reduces the number of interface signals in designs where pin density is constrained. The integrated copper PHYs also support designs intended to connect directly to Ethernet magnetics and RJ45 front ends.
Hardware implementation requires careful attention to the manufacturer's KSZ8895FQX Hardware Design Checklist. The checklist specifies the RJ45 transmit-channel connections, including TX+ on RJ45 pin 3, TX- on RJ45 pin 6, and a 75-ohm series termination path through a 1000 pF, 2 kV capacitor to chassis ground. These network-interface details should be implemented exactly as described in the manufacturer document rather than inferred from generic Ethernet layouts.
This product page combines the confirmed five-port 10/100 switch functionality, package information, manufacturer guidance, qualified replacement relationships, and practical hardware-design guidance. It is intended to help engineers identify the correct Microchip orderable variant, plan the MII or RMII host connection, and evaluate whether the same-package KSZ8895 family can satisfy a lifecycle or sourcing requirement without changing the PCB footprint.
بدائل مباشرة لـ KSZ8895FQXI — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع KSZ8895FQXI (نفس عامل الشكل والبصمة) — يختلف في Package, Product Type, Host Interface.
KSZ8895MQXCA
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
KSZ8895RQXI
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←KSZ8895RQXIA
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
KSZ8895MQXI
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←KSZ8993I
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
KSZ8895FQXI الحدود القصوى والخصائص الكهربائية
| Product Type | Managed Layer 2 Ethernet switch |
| Number of Ethernet Ports | 5 ports |
| Supported Ethernet Speeds | 10 Mb/s and 100 Mb/s |
| Integrated PHY Configuration | 5 integrated 10BASE-T/100BASE-TX PHYs |
| Host Interface | MII and RMII |
| Operating Voltage | 3.3 V |
| العلبة | 128-pin PQFP, 14 mm x 20 mm |
| نوع التركيب | Surface mount |
| Network Layer | Layer 2 |
| Automotive Qualification | Automotive qualified |
| 10BASE-T Driver Integration | 10BASE-T driver incorporated into the 100BASE-T driver |
| 10BASE-T Output Amplitude | 2.3 V typical |
| Output Wave Shaping | Internally wave-shaped |
| Output Pre-emphasis | Internally pre-emphasized |
| RJ45 Transmit Channel Termination | 75 ohm in series with a 1000 pF, 2 kV capacitor to chassis ground |
دليل تكوين أطراف KSZ8895FQXI 128-pin pqfp, 14 mm x 20 mm
تكوين الأطراف لـ KSZ8895FQXI (حزمة 128-pin pqfp, 14 mm x 20 mm). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ KSZ8895FQXI.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
KSZ8895FQXI مناسب لـ 6 التطبيقs: Automotive In-Vehicle Ethernet, Industrial Ethernet Gateway, Factory Automation Controller, Building Automation Equipment, Embedded Communications Equipment, Network Appliance Front Panel.
Automotive In-Vehicle Ethernet
The KSZ8895FQXI fits automotive in-vehicle Ethernet designs that need five managed 10/100 ports, Layer 2 switching, and a compact processor interface. Its integrated copper PHYs reduce the number of external networking devices, while MII and RMII provide flexibility for different embedded host architectures. The device is automotive qualified according to Microchip's product description. An in-vehicle design should still verify the exact ordering code's temperature range, EMC behavior, and qualification conditions against the manufacturer datasheet. The 128-PQFP package also requires careful high-speed trace planning and a stable 3.3 V supply network so that five-port traffic does not degrade signal integrity or network availability.
موصى به
Industrial Ethernet Gateway
The KSZ8895FQXI is appropriate for an industrial gateway that aggregates several 10/100 wired-network segments before passing traffic to an embedded processor. Five integrated 10BASE-T/100BASE-TX ports can consolidate a compact gateway architecture without a separate PHY for every copper connection, while managed Layer 2 operation supports controlled forwarding and port administration. RMII is especially useful where interface-pin count is constrained, and MII provides a parallel alternative for legacy processor platforms. The gateway must add the required Ethernet magnetics, RJ45 protection, isolation strategy, and chassis-ground termination. Use the manufacturer's hardware checklist for the recommended 75-ohm, 1000 pF, 2 kV capacitor transmit-channel termination path.
موصى به
Factory Automation Controller
A factory automation controller can use the KSZ8895FQXI to combine five 10/100 network ports in a deterministic Layer 2 switching block. The integrated PHYs support 10 Mb/s and 100 Mb/s devices on the same network infrastructure, which is useful when connecting programmable controllers, sensors, operator panels, and service equipment. Host communication can use RMII to reduce parallel interface routing or MII when the controller platform benefits from direct control of individual bus signals. Because industrial installations experience conducted noise and surge events, the implementation must follow the manufacturer's external-circuit recommendations and include appropriate magnetics and protection. The 3.3 V operating rail should be filtered close to the device, and all 128 package contacts must be assigned according to the official pin-description table.
موصى به
Building Automation Equipment
The KSZ8895FQXI suits building-automation equipment that connects multiple wired controller or sensor nodes through managed 10/100 Ethernet ports. Its Layer 2 management supports structured port operation, while the five integrated ports can simplify a multi-segment controller architecture. The choice between MII and RMII depends on the host processor and available pin budget: MII exposes a broad parallel interface, whereas RMII provides a more compact connection for space-constrained control boards. Copper ports still require suitable Ethernet magnetics, RJ45 interfaces, and surge protection appropriate to the building installation. Follow the manufacturer's 128-PQFP layout and pin-assignment guidance, and use the specified 75-ohm transmit-channel termination with a 1000 pF, 2 kV capacitor toward chassis ground for predictable EMC behavior.
موصى به
Embedded Communications Equipment
The KSZ8895FQXI can serve as the five-port Ethernet switching core in embedded communications equipment requiring managed Layer 2 connectivity. Its 10/100 support accommodates conventional office, control, and service links while its MII and RMII options allow connection to a communications processor without introducing separate PHYs on every port. The internally wave-shaped and pre-emphasized 10BASE-T/100BASE-T driver arrangement permits shared magnetics, according to the manufacturer datasheet, helping control external-component count. Designers should still validate link performance across the required temperature range, cable lengths, and network traffic. Keep the 3.3 V distribution quiet, place bypass and required network components close to their assigned pins, and preserve the manufacturer's recommended RJ45 termination network.
موصى به
Network Appliance Front Panel
The KSZ8895FQXI is useful in a network appliance front panel where multiple 10/100 service, diagnostic, or management ports must be consolidated behind one processor interface. Five managed ports can provide controlled Layer 2 forwarding for configuration traffic, maintenance links, and embedded equipment that cannot justify five external PHY devices. RMII can simplify the processor connection in a compact appliance, while MII may be preferred when the host platform requires separate control of clock, carrier, and data signals. Ethernet magnetics and RJ45 interfaces remain external, so each channel must follow the reference circuit and termination requirements. The large 128-pin PQFP footprint demands disciplined escape routing, adequate ground-plane continuity, and careful review of high-speed MII or RMII trace topology.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ KSZ8895FQXI — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | KSZ8895MQXCA | KSZ8895RQXI | KSZ8895RQXIA | KSZ8993I |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 128-PQFP (14 x 20 mm) | 128-PQFP (14 x 20 mm) | 128-PQFP (14 x 20 mm) | 128-PQFP (14 x 20 mm) | 128-PQFP (14 x 20 mm) |
| Ethernet Ports | 5 | 5 | 5 | 5 | 5 |
| Supported Speed | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s | 100 Mb/s |
| Switching Layer | Layer 2 managed | Layer 2 managed | Layer 2 managed | Layer 2 managed | Automotive Ethernet switch |
أبرز الفروقات
- Five integrated 10/100 ports in one switch device (مقابلKSZ8993I)
- MII and RMII host-interface options (مقابلKSZ8993I)
- Shared 10/100 magnetics architecture (مقابلKSZ8993I)
ملاحظات التصميم
Implement the manufacturer-recommended RJ45 transmit-channel circuit exactly as described in the KSZ8895FQX Hardware Design Checklist. RJ45 pin 3 connects to TX+, RJ45 pin 6 connects to TX-, and the transmit channel uses 75-ohm termination through a 1000 pF, 2 kV capacitor to chassis ground. Preserve the specified return path and keep this network isolated from sensitive signal grounds where the reference design requires separation.
Plan the MII or RMII interface as a high-speed digital signal path even though the associated Ethernet links operate at 10/100 Mb/s. Use the manufacturer's interface timing and layout guidance, provide a continuous return path beneath the signals, minimize stubs, and place required termination and decoupling components close to the KSZ8895FQXI pins. The 128-pin PQFP footprint also requires adequate escape routing between the fine-pitch package and the magnetics or host processor.
Design the 3.3 V rail to support the combined demand of the managed switch and all five integrated copper PHYs. Place the manufacturer-specified bypass capacitors close to their assigned power pins, keep the high-current return path compact, and avoid routing switching-supply or digital high-current paths beneath sensitive MII/RMII and Ethernet magnetics nodes. Validate startup and full-port activity against the worst-case load condition rather than an idle link state.
Do not treat a shared package as proof that every KSZ8895 ordering suffix is an automatic substitute. Before using an MQX, RQX, or FQX-family replacement, compare the exact ordering information, temperature grade, qualification, package, and pin-level differences in Microchip's documentation. Also avoid treating the 10BASE-T and 100BASE-TX capabilities as interchangeable without validating the associated magnetics and link requirements.
معلومات الامتثال
Microchip identifies the KSZ8895 as automotive qualified. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements are not established by the cited product information and remain unknown.
