KSZ8895FQXI - 5-Port 10/100 Managed Ethernet Switch | Microchip Technology
MPN: KSZ8895FQXI ✓ Hoạt độngKSZ8895FQXI Tóm tắt
An Ethernet switch is a Layer 2 networking semiconductor that receives Ethernet frames on one port and forwards them to the appropriate destination port using MAC-address information. The KSZ8895 belongs to the broader hierarchy of Ethernet interface controllers, network switches, Layer 2 devices, and integrated network semiconductors. Its managed architecture allows a host processor or network controller to configure port behavior, while its MII and RMII interfaces support integration with embedded processors, field-programmable gate arrays, application processors, and industrial controllers.
The KSZ8895FQXI provides five integrated 10/100 Ethernet ports, MII and RMII connectivity, and a single 3.3 V operating voltage. Its 128-PQFP 14 x 20 mm package exposes the switch, copper-physical-layer, control, management, clock, and power interfaces through 128 contacts. The automotive qualification indicated by Microchip makes the device relevant to vehicle-network designs as well as industrial, communications, and embedded applications requiring a compact managed Ethernet switch. A single-chip switching design can also reduce board area, external PHY count, and system-level assembly complexity.
Microchip's integrated 10/100 Ethernet-switch implementation combines the 100BASE-TX drivers and 10BASE-T drivers so both can use the same magnetics. The 10BASE-T driver is incorporated into the 100BASE-T driver, with internally wave-shaped and pre-emphasized outputs having a typical 2.3 V amplitude. This integration supports shared copper-magnetics designs while preserving separate logical support for 10 Mb/s and 100 Mb/s operation. Management features are included at the Layer 2 level rather than requiring a separate switch controller for basic port management.
Typical applications include automotive infotainment and in-vehicle networking, industrial Ethernet gateways, factory automation controllers, building-automation equipment, communications equipment, and embedded systems that need several 10/100 ports behind one processor interface. MII is useful when the connected host requires parallel data and control signals, while RMII reduces the number of interface signals in designs where pin density is constrained. The integrated copper PHYs also support designs intended to connect directly to Ethernet magnetics and RJ45 front ends.
Hardware implementation requires careful attention to the manufacturer's KSZ8895FQX Hardware Design Checklist. The checklist specifies the RJ45 transmit-channel connections, including TX+ on RJ45 pin 3, TX- on RJ45 pin 6, and a 75-ohm series termination path through a 1000 pF, 2 kV capacitor to chassis ground. These network-interface details should be implemented exactly as described in the manufacturer document rather than inferred from generic Ethernet layouts.
This product page combines the confirmed five-port 10/100 switch functionality, package information, manufacturer guidance, qualified replacement relationships, and practical hardware-design guidance. It is intended to help engineers identify the correct Microchip orderable variant, plan the MII or RMII host connection, and evaluate whether the same-package KSZ8895 family can satisfy a lifecycle or sourcing requirement without changing the PCB footprint.
Bộ thay thế dễ dàng lắp đặt cho KSZ8895FQXI — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với KSZ8895FQXI (cùng hình factor và footprint) — khác nhau ở Package, Product Type, Host Interface.
KSZ8895MQXCA
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ8895RQXI
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →KSZ8895RQXIA
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ8895MQXI
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →KSZ8993I
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ8895FQXI Tỷ lệ tối đa & tính chất điện
| Product Type | Managed Layer 2 Ethernet switch |
| Number of Ethernet Ports | 5 ports |
| Supported Ethernet Speeds | 10 Mb/s and 100 Mb/s |
| Integrated PHY Configuration | 5 integrated 10BASE-T/100BASE-TX PHYs |
| Host Interface | MII and RMII |
| Operating Voltage | 3.3 V |
| Hộp | 128-pin PQFP, 14 mm x 20 mm |
| Kiểu lắp đặt | Surface mount |
| Network Layer | Layer 2 |
| Automotive Qualification | Automotive qualified |
| 10BASE-T Driver Integration | 10BASE-T driver incorporated into the 100BASE-T driver |
| 10BASE-T Output Amplitude | 2.3 V typical |
| Output Wave Shaping | Internally wave-shaped |
| Output Pre-emphasis | Internally pre-emphasized |
| RJ45 Transmit Channel Termination | 75 ohm in series with a 1000 pF, 2 kV capacitor to chassis ground |
Hướng dẫn cấu hình chân KSZ8895FQXI 128-pin pqfp, 14 mm x 20 mm
Cấu hình chân cho KSZ8895FQXI (128-pin pqfp, 14 mm x 20 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho KSZ8895FQXI.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
KSZ8895FQXI phù hợp cho 6 Áp dụngs: Automotive In-Vehicle Ethernet, Industrial Ethernet Gateway, Factory Automation Controller, Building Automation Equipment, Embedded Communications Equipment, Network Appliance Front Panel.
Automotive In-Vehicle Ethernet
The KSZ8895FQXI fits automotive in-vehicle Ethernet designs that need five managed 10/100 ports, Layer 2 switching, and a compact processor interface. Its integrated copper PHYs reduce the number of external networking devices, while MII and RMII provide flexibility for different embedded host architectures. The device is automotive qualified according to Microchip's product description. An in-vehicle design should still verify the exact ordering code's temperature range, EMC behavior, and qualification conditions against the manufacturer datasheet. The 128-PQFP package also requires careful high-speed trace planning and a stable 3.3 V supply network so that five-port traffic does not degrade signal integrity or network availability.
Được đề xuất
Industrial Ethernet Gateway
The KSZ8895FQXI is appropriate for an industrial gateway that aggregates several 10/100 wired-network segments before passing traffic to an embedded processor. Five integrated 10BASE-T/100BASE-TX ports can consolidate a compact gateway architecture without a separate PHY for every copper connection, while managed Layer 2 operation supports controlled forwarding and port administration. RMII is especially useful where interface-pin count is constrained, and MII provides a parallel alternative for legacy processor platforms. The gateway must add the required Ethernet magnetics, RJ45 protection, isolation strategy, and chassis-ground termination. Use the manufacturer's hardware checklist for the recommended 75-ohm, 1000 pF, 2 kV capacitor transmit-channel termination path.
Được đề xuất
Factory Automation Controller
A factory automation controller can use the KSZ8895FQXI to combine five 10/100 network ports in a deterministic Layer 2 switching block. The integrated PHYs support 10 Mb/s and 100 Mb/s devices on the same network infrastructure, which is useful when connecting programmable controllers, sensors, operator panels, and service equipment. Host communication can use RMII to reduce parallel interface routing or MII when the controller platform benefits from direct control of individual bus signals. Because industrial installations experience conducted noise and surge events, the implementation must follow the manufacturer's external-circuit recommendations and include appropriate magnetics and protection. The 3.3 V operating rail should be filtered close to the device, and all 128 package contacts must be assigned according to the official pin-description table.
Được đề xuất
Building Automation Equipment
The KSZ8895FQXI suits building-automation equipment that connects multiple wired controller or sensor nodes through managed 10/100 Ethernet ports. Its Layer 2 management supports structured port operation, while the five integrated ports can simplify a multi-segment controller architecture. The choice between MII and RMII depends on the host processor and available pin budget: MII exposes a broad parallel interface, whereas RMII provides a more compact connection for space-constrained control boards. Copper ports still require suitable Ethernet magnetics, RJ45 interfaces, and surge protection appropriate to the building installation. Follow the manufacturer's 128-PQFP layout and pin-assignment guidance, and use the specified 75-ohm transmit-channel termination with a 1000 pF, 2 kV capacitor toward chassis ground for predictable EMC behavior.
Được đề xuất
Embedded Communications Equipment
The KSZ8895FQXI can serve as the five-port Ethernet switching core in embedded communications equipment requiring managed Layer 2 connectivity. Its 10/100 support accommodates conventional office, control, and service links while its MII and RMII options allow connection to a communications processor without introducing separate PHYs on every port. The internally wave-shaped and pre-emphasized 10BASE-T/100BASE-T driver arrangement permits shared magnetics, according to the manufacturer datasheet, helping control external-component count. Designers should still validate link performance across the required temperature range, cable lengths, and network traffic. Keep the 3.3 V distribution quiet, place bypass and required network components close to their assigned pins, and preserve the manufacturer's recommended RJ45 termination network.
Được đề xuất
Network Appliance Front Panel
The KSZ8895FQXI is useful in a network appliance front panel where multiple 10/100 service, diagnostic, or management ports must be consolidated behind one processor interface. Five managed ports can provide controlled Layer 2 forwarding for configuration traffic, maintenance links, and embedded equipment that cannot justify five external PHY devices. RMII can simplify the processor connection in a compact appliance, while MII may be preferred when the host platform requires separate control of clock, carrier, and data signals. Ethernet magnetics and RJ45 interfaces remain external, so each channel must follow the reference circuit and termination requirements. The large 128-pin PQFP footprint demands disciplined escape routing, adequate ground-plane continuity, and careful review of high-speed MII or RMII trace topology.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho KSZ8895FQXI — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | KSZ8895MQXCA | KSZ8895RQXI | KSZ8895RQXIA | KSZ8993I |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 128-PQFP (14 x 20 mm) | 128-PQFP (14 x 20 mm) | 128-PQFP (14 x 20 mm) | 128-PQFP (14 x 20 mm) | 128-PQFP (14 x 20 mm) |
| Ethernet Ports | 5 | 5 | 5 | 5 | 5 |
| Supported Speed | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s | 100 Mb/s |
| Switching Layer | Layer 2 managed | Layer 2 managed | Layer 2 managed | Layer 2 managed | Automotive Ethernet switch |
Bảo phân biệt quan trọng
- Five integrated 10/100 ports in one switch device (vsKSZ8993I)
- MII and RMII host-interface options (vsKSZ8993I)
- Shared 10/100 magnetics architecture (vsKSZ8993I)
Ghi chú thiết kế
Implement the manufacturer-recommended RJ45 transmit-channel circuit exactly as described in the KSZ8895FQX Hardware Design Checklist. RJ45 pin 3 connects to TX+, RJ45 pin 6 connects to TX-, and the transmit channel uses 75-ohm termination through a 1000 pF, 2 kV capacitor to chassis ground. Preserve the specified return path and keep this network isolated from sensitive signal grounds where the reference design requires separation.
Plan the MII or RMII interface as a high-speed digital signal path even though the associated Ethernet links operate at 10/100 Mb/s. Use the manufacturer's interface timing and layout guidance, provide a continuous return path beneath the signals, minimize stubs, and place required termination and decoupling components close to the KSZ8895FQXI pins. The 128-pin PQFP footprint also requires adequate escape routing between the fine-pitch package and the magnetics or host processor.
Design the 3.3 V rail to support the combined demand of the managed switch and all five integrated copper PHYs. Place the manufacturer-specified bypass capacitors close to their assigned power pins, keep the high-current return path compact, and avoid routing switching-supply or digital high-current paths beneath sensitive MII/RMII and Ethernet magnetics nodes. Validate startup and full-port activity against the worst-case load condition rather than an idle link state.
Do not treat a shared package as proof that every KSZ8895 ordering suffix is an automatic substitute. Before using an MQX, RQX, or FQX-family replacement, compare the exact ordering information, temperature grade, qualification, package, and pin-level differences in Microchip's documentation. Also avoid treating the 10BASE-T and 100BASE-TX capabilities as interchangeable without validating the associated magnetics and link requirements.
Thông tin tuân thủ
Microchip identifies the KSZ8895 as automotive qualified. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements are not established by the cited product information and remain unknown.
