Texas Instruments

LM211DRE4 - 115 ns Differential Comparator | Texas Instruments

MPN: LM211DRE4 ✓ نشط
3.5 V to 30 V Vdss 8-pin SOIC Package
الحد الأدنى للطلب: 1 |

LM211DRE4 نظرة عامة

Texas Instruments LM211DRE4 is a single differential voltage comparator with strobe inputs, 115 ns response time, and an 8-pin SOIC package. The device operates from 3.5 V to 30 V, supports single-supply operation from 5 V to 30 V or split supplies up to ±15 V, and provides an open-collector output compatible with TTL, MOS, DTL, and RTL logic. Its operating temperature range is -40°C to 85°C.

A voltage comparator is an analog interface IC that compares two input voltages and produces a logic-level output indicating which input is higher. The comparator belongs to the broader hierarchy of analog comparator, analog IC, and semiconductor. Unlike a general-purpose operational amplifier, the LM211DRE4 is optimized for fast threshold decisions, regenerative switching behavior, and direct interface with digital logic systems.

The LM211 family combines a differential input stage with an open-collector output and dedicated strobe control. Its 115 ns propagation response supports rapid level detection, while its wide supply range allows operation from ±15 V analog systems as well as 5 V logic rails. The open-collector output can sink logic-level current and can be pulled up for wired logic, relay interfaces, or lamp-driving arrangements.

The comparator's inputs can operate independently of system ground when split supplies are used, providing useful flexibility in legacy industrial and instrumentation circuits. Output levels are compatible with most TTL and MOS circuits, reducing the need for intermediate logic drivers. Two strobe inputs support latch-like control in test equipment, pulse-width systems, and switching networks where the output state must be actively enabled or disabled.

Typical applications include industrial control and automation, power-supply supervision, signal threshold detection, test and measurement instrumentation, relay or lamp interfaces, and legacy digital logic interfaces. The 8-pin SOIC package supports through-hole assembly and PCB layouts based on the standard SOIC footprint. The broad supply range also makes the device suitable for systems transitioning between older ±15 V equipment and newer single-rail electronics.

Designers should verify output pull-up voltage, sink current, input common-mode range, and strobe logic levels for the intended system. Because the output is open collector, an external pull-up resistor is normally required. Keep the comparator close to the sensed signal and logic interface to reduce susceptibility to noise and propagation-delay variation on long traces.

This page combines manufacturer specifications, practical circuit guidance, comparison parameters, and pin-compatible replacement information. It also distinguishes true drop-in options from related devices that require different output, timing, supply, or qualification behavior, helping engineers choose a replacement without overlooking circuit-level compatibility.

بدائل مباشرة لـ LM211DRE4 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع LM211DRE4 (نفس عامل الشكل والبصمة) — يختلف في Comparator Type, Output Type, Logic Compatibility, Operating Temperature Range, Output Drive Capability.

onsemi
Comparator Type: Single high-speed voltage comparator
Output Type: Open-collector
Logic Compatibility: DTL, MOS, RTL, and TTL
قارن مع LM211DRE4 →
Texas Instruments
Comparator Type: Single high-speed differential comparator
Output Type: Open-collector / open-emitter
Logic Compatibility: DTL, MOS, RTL, and TTL
قارن مع LM211DRE4 →

LM211DG

✅ بديل مباشر
onsemi
📦 8-pin SOIC
Single high-speed voltage comparator · 1 channel · 200 ns · 5 V to 30 V · ±15 V · Open-collector · DTL, MOS, RTL, and TTL · Inputs can be isolated from system ground

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM211QDR

✅ بديل مباشر
📦 8-pin SOIC
Same LM211 115 ns response, 3.5 V to 30 V supply range, and 8-pin SOIC footprint; suffix-specific temperature and qualification attributes differ or require confirmation.

📋 بديل مرجعي (غير موجود في الكتالوج)

LP211DRE4

✅ بديل مباشر
📦 8-pin SOIC
Same 8-pin SOIC footprint and open-collector comparator function, but the LP211 response is approximately 200 ns versus 115 ns, an increase of about 74%.

📋 بديل مرجعي (غير موجود في الكتالوج)

LM311DRE4

✅ بديل مباشر
📦 8-pin SOIC
Same 8-pin SOIC footprint and open-collector comparator function, but the LM311 response is approximately 200 ns versus 115 ns, an increase of about 74%.

📋 بديل مرجعي (غير موجود في الكتالوج)

LM211DRE4 الحدود القصوى والخصائص الكهربائية

Comparator Type Single differential voltage comparator with strobes
Propagation Delay 115 ns
Supply Voltage Range 3.5 V to 30 V
Single-Supply Operation 5 V to 30 V
Split-Supply Operation ±15 V
نوع الخرج Open collector
Logic Compatibility TTL, MOS, DTL, and RTL compatible
Number of Channels 1 channel
العلبة 8-pin SOIC
عدد الأطراف 8 pins
نوع التركيب Surface mount
نطاق درجة حرارة التشغيل -40°C to 85°C
Strobe Inputs 2 strobe inputs
Output-Level Compatibility Compatible with most TTL and MOS circuits
Load-Driving Capability Capable of driving lamps or relays

دليل تكوين أطراف LM211DRE4 8-pin soic

تكوين الأطراف لـ LM211DRE4 (حزمة 8-pin soic). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 8-pin soic لـ LM211DRE4

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM211DRE4.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

LM211DRE4 مناسب لـ 6 التطبيقs: Industrial Control Signal Conditioning, Power-Supply Overvoltage Detection, Test and Measurement Threshold Detection, Relay and Lamp Interface, Digital Logic Level Detection, Pulse Width and Timing Circuits.

🏭

Industrial Control Signal Conditioning

The LM211DRE4 fits industrial control circuits that convert an analog process signal into a fast logic decision. Its 115 ns propagation delay allows a threshold change to reach the controller before the next significant control interval, while the 3.5 V to 30 V supply range supports both 5 V logic systems and higher-voltage legacy control boards. Place the comparator close to the sensor interface and use the open-collector output with a pull-up matching the controller input. The principal trade-off is that the open-collector transition requires an RC-shaped rising edge, so the pull-up value and bus capacitance must be checked against timing requirements.

⚡

Power-Supply Overvoltage Detection

The LM211DRE4 can monitor a rectified or regulated rail and generate a digital fault signal when the monitored voltage crosses a reference threshold. Its wide 3.5 V to 30 V operating range allows use in systems with 5 V, 12 V, 24 V, or 30 V rails, while the 115 ns response rapidly identifies a threshold crossing. The sensing divider and reference must remain within the input common-mode limits, and the output pull-up should be connected to the system logic rail. Because the output is open collector, the topology supports wired fault signaling and fail-safe logic without adding a push-pull output driver.

🔧

Test and Measurement Threshold Detection

The LM211DRE4 is appropriate for laboratory and production-test circuits that need to decide whether a measured signal is above or below a selected threshold. A 115 ns response time helps preserve timing relationships in pulse, burst, or repetitive test sequences, and the TTL- and MOS-compatible output can trigger digital test equipment. The external pull-up resistor controls the high-state rise time and must be selected together with the input capacitance of the instrument. For instrumentation operating from split supplies, the family supports operation up to ±15 V, helping simplify legacy analog front ends while retaining a standard 8-pin SOIC footprint.

⚡

Relay and Lamp Interface

The LM211DRE4 can serve as the decision element preceding a relay or lamp because the Texas Instruments family is identified as capable of driving such loads. Its open-collector output can pull down the low side of a properly designed load circuit, while the 115 ns response provides rapid switching. A flyback diode is required across an inductive relay coil, and the supply and output ratings must accommodate the load's off-state voltage and current. The logic pull-up must remain active when the load is switched off, and the board layout should keep the high-current load path separate from the comparator's sensitive input and timing traces.

🖥️

Digital Logic Level Detection

The LM211DRE4 can translate a changing analog voltage into a logic-compatible event for TTL, MOS, DTL, or RTL systems. The 115 ns response reduces timing uncertainty when the comparator is used as a pulse-edge or threshold detector, while its broad supply range supports both 5 V systems and higher-voltage legacy interfaces. The open-collector output requires an external pull-up, whose value sets the rise time and determines the permissible fan-out. Designers should verify the pull-up voltage against the receiving device, account for the output sink-current limit, and avoid excessive capacitance on the output node.

📡

Pulse Width and Timing Circuits

The LM211DRE4 can form part of pulse-width and timing circuits because its 115 ns propagation delay is short enough for many legacy control and instrumentation systems. The strobe inputs allow a surrounding logic network to enable or inhibit the comparison at defined moments, supporting gated acquisition and repeatable measurement sequences. The open-collector output can feed a counter, timer, or latch through a pull-up resistor, although the resistor-capacitor network introduces a deliberate rise-time limit. Circuit simulation should include the pull-up value, wiring capacitance, and input overdrive because these factors can dominate the apparent switching time.

ملخص المنتجات الموصى بها

LM311DRE4 Related 8-pin SOIC comparator for slower threshold decisions يُستخدم في: Industrial Control Signal Conditioning, Power-Supply Overvoltage Detection, Relay and Lamp Interface, Digital Logic Level Detection LP211DRE4 Related open-collector comparator option يُستخدم في: Industrial Control Signal Conditioning, Test and Measurement Threshold Detection, Pulse Width and Timing Circuits LM211QDR Same-family comparator for an alternate ordering configuration يُستخدم في: Power-Supply Overvoltage Detection, Relay and Lamp Interface, Pulse Width and Timing Circuits LM211DG onsemi يُستخدم في: Test and Measurement Threshold Detection, Digital Logic Level Detection
What is the operating voltage of LM211DRE4?
The LM211DRE4 operates from 3.5 V to 30 V. According to the Texas Instruments LM211 product information, the family can also operate from a single 5 V to 30 V supply or from split supplies up to ±15 V, covering both legacy analog systems and modern logic rails. The selected supply arrangement must keep both input pins and the output pull-up network within their allowed common-mode and voltage limits.
How fast is the LM211DRE4 comparator?
The LM211DRE4 has a 115 ns propagation delay, as identified in its published specifications. This response time makes it suitable for rapid threshold crossing, pulse detection, and comparator-controlled switching functions. Actual system timing also depends on input overdrive, source impedance, output pull-up resistance, and the capacitance presented by the receiving logic circuit.
Where can I download the LM211DRE4 datasheet PDF?
The official LM211DRE4 documentation is available through the Texas Instruments LM211 product page, which links to the manufacturer datasheet and supporting technical information. The distributor-hosted PDF copies can also be useful, but the TI product page is the preferred source for revisions, ordering information, and family-level application guidance.
Where can I find the LM211DRE4 pinout?
The LM211DRE4 pinout is defined in the manufacturer datasheet for the 8-pin SOIC package. Use the pin-description table there when assigning the differential inputs, supply rails, ground, strobe controls, and open-collector output. The component uses the standard soic-8 package key on this page, but the manufacturer pin table remains the controlling reference for board design.
Why does the LM211DRE4 output need a pull-up resistor?
The LM211DRE4 uses an open-collector output, so the output transistor actively pulls the node low but does not supply a high output voltage. A pull-up resistor establishes the high state and should be selected for the receiving logic's voltage, sink-current capability, rise-time requirement, and maximum bus loading. The resistor value also determines how quickly the output returns high after the comparator releases the node.
Can LM211DRE4 drive a relay or lamp?
The LM211DRE4 is described as capable of driving lamps or relays, but the external load path must be designed carefully because the output is open collector. Use a flyback diode for an inductive relay coil and ensure the comparator's maximum output voltage and sink-current limits are not exceeded. The logic pull-up should be connected to a supply that remains present while the load is energized.
LM211DRE4 vs LM311DRE4 - which comparator is better for fast threshold detection?
Choose the LM211DRE4 for faster threshold detection because its published propagation delay is 115 ns, while the LM311DRE4 family is a slower related comparator. Both use an 8-pin SOIC format and an open-collector output, but replacing one with the other must be checked against common-mode range, supply limits, timing, input current, and load requirements. The LM211 is generally preferable when response time is the primary selection criterion.
LM211DRE4 vs LP211DRE4 - what should I verify before replacing one?
The LM211DRE4 and LP211DRE4 are related 8-pin SOIC comparators, but the LM211's published 115 ns propagation delay makes it the stronger choice for faster switching decisions. Before substituting the LP211, compare input offset voltage, input bias and offset currents, common-mode range, output timing, supply requirements, and the logic loads connected to each pin. A common footprint does not guarantee equivalent precision or dynamic performance.
When should I choose LM211DRE4 over LM211QDR?
Choose LM211DRE4 when a standard commercial-temperature LM211 configuration in 8-pin SOIC meets the required supply, timing, and qualification specifications. Choose LM211QDR when its specific ordering, environmental, or screening characteristics provide a necessary advantage for the application. Confirm the complete suffix-specific temperature rating and ordering details in the Texas Instruments product documentation before releasing the BOM.
Is LM211DRE4 suitable for industrial control and test equipment?
The LM211DRE4 is well suited to many industrial control and test-equipment circuits because it supports supply voltages from 3.5 V to 30 V, responds in 115 ns, and provides an open-collector output for TTL or MOS interfacing. Its -40°C to 85°C operating range covers many commercial and industrial environments, but individual equipment may require a wider temperature grade or additional environmental qualification.
What can replace LM211DRE4?
The closest documented pin-compatible choices are LM211DG, LM211QDR, LP211DRE4, and LM311DRE4, all associated with 8-pin SOIC configurations, but none should be treated as an automatic substitute. The LM211 variants preserve the comparator family most closely, while LP211DRE4 and LM311DRE4 differ in timing and electrical details. Check every connected pin and compare the manufacturer specifications before replacement.
Is LM211DRE4 the same as LM311DRE4?
No. The LM211DRE4 is a 115 ns comparator, whereas the LM311DRE4 belongs to the related LM311 family with different speed, input-current, and operating characteristics. Their 8-pin SOIC packages can support board-level substitution studies, but the LM311 is not a functional drop-in for every LM211 circuit. Verify supply range, input behavior, common-mode limits, output timing, and load current.
What are the key specifications of LM211DRE4 that engineers should know?
The principal LM211DRE4 specifications are a 3.5 V to 30 V supply range, 115 ns propagation delay, open-collector output, TTL and MOS compatibility, two strobe inputs, and an 8-pin SOIC package. According to the Texas Instruments LM211 product information, the device also supports 5 V to 30 V single supplies and ±15 V split supplies. Its -40°C to 85°C operating range covers a broad range of industrial and commercial designs.
Where to buy LM211DRE4 online?
Use the Request a Quote form on this page to request LM211DRE4 availability, current commercial terms, and a quotation for the required quantity. The form allows the request to be tied to the exact 8-pin SOIC ordering code rather than a family-level LM211 designation. Confirm authorized sourcing, lot traceability, and current lifecycle status before placing a production order.
What is the price of LM211DRE4?
The current commercial price of LM211DRE4 is generated through the Request a Quote form on this page. The form can return current unit terms for the requested quantity and packaging configuration without embedding a stale price in the product description. Confirm quantity breaks, date-code requirements, and authorized-distributor traceability as part of the quotation.
What is the lead time and stock status for LM211DRE4?
Current LM211DRE4 stock and lead time should be requested through the Request a Quote form on this page. The request should state the quantity, acceptable date-code window, and whether reel, tube, or another approved delivery format is required. The form provides the current sourcing response while avoiding unsupported inventory claims.

بيانات مرجعية هندسية لـ LM211DRE4 — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the LM211DRE4 when a fast, single-channel comparator with a 115 ns response, open-collector output, strobe controls, and 8-pin SOIC footprint is required. It is particularly appropriate for industrial control, threshold detection, legacy logic interfacing, and power-supply monitoring designs that operate across the family's 3.5 V to 30 V supply range. LM211DG or LM211QDR may be preferable when their specific suffix attributes better match sourcing or environmental requirements while preserving the same core response and package. Consider LP211DRE4 only when its slower approximately 200 ns response is acceptable and all precision and input-current differences have been reviewed. LM311DRE4 is a related 8-pin SOIC option, but its approximately 200 ns response and different electrical characteristics make it less suitable when speed is the primary requirement. In every case, verify input common-mode limits, strobe levels, output pull-up requirements, supply sequencing, and load-current capability before approving a substitution.

المقارنة مع البدائل

المعامل هذا المنتج LM211DG LM211QDR LP211DRE4 LM311DRE4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same
Comparator Type Single differential comparator with strobes Single differential comparator with strobes Single differential comparator with strobes Single differential comparator Single differential comparator with strobes
Propagation Delay 115 ns 115 ns 115 ns Approximately 200 ns Approximately 200 ns
Output Type Open collector Open collector Open collector Open collector Open collector
Number of Channels 1 channel 1 channel 1 channel 1 channel 1 channel

أبرز الفروقات

  • Faster response than the LM311-family alternative (مقابلLM311DRE4)
  • Faster response than the LP211-family alternative (مقابلLP211DRE4)
  • Closest same-family pin-compatible sourcing options (مقابلLM211QDR)
  • Wide supply support within the same SOIC footprint (مقابلLM211DG)

ملاحظات التصميم

The output is open collector and therefore requires an external pull-up resistor for normal high-state operation. Select the resistor using the receiving logic's high-level voltage, the LM211 sink-current limit, bus capacitance, and the required rising-edge time. Avoid using an excessively large pull-up, because it can slow transitions and make the circuit susceptible to noise; avoid an excessively small pull-up, because it can overload the output transistor.

Place the comparator, its input resistor network, and the output pull-up resistor close to the device, particularly when the input is a high-impedance sensing node. Keep the pull-up and load-current return path physically separated from the input and reference traces to reduce supply transients and ground bounce. Route strobe signals away from the differential input pair, and use a stable ground reference for both the sensing divider and comparator.

A 115 ns propagation delay applies to the comparator's specified operating conditions, but practical switching time also depends on input overdrive, source impedance, output pull-up resistance, and load capacitance. Check the maximum overdrive needed for consistent timing and include output rise time in pulse-width calculations. For fast edges or long PCB traces, use a local receiver or buffer rather than assuming the nominal delay describes the complete signal transition.

Verify that the selected supply remains within the 3.5 V to 30 V operating range in every operating state. If the output pull-up is connected to a rail different from the comparator supply, ensure that rail is present before the LM211DRE4 can pull the output low. Decouple the supply near pin 8 with a short, low-inductance path, and avoid routing load-return current through the comparator's ground reference.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The E4 ordering code is associated with lead-free assembly nomenclature, but explicit RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 declarations require confirmation in the current manufacturer documentation.

تم التحقق من البيانات في: 2026-11-15 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

LM211DRE4 datasheet LM211DRE4 pinout LM211DRE4 datasheet pdf LM211DRE4 equivalent LM211DRE4 replacement LM211DRE4 drop-in replacement LM211DRE4 vs LM311DRE4 LM211DRE4 vs LP211DRE4 LM211DRE4 115 ns comparator LM211DRE4 8-SOIC footprint LM211DRE4 application circuit LM211DRE4 price LM211DRE4 stock Texas Instruments LM211DRE4 LM211 open collector strobe circuit

المكونات والمصطلحات ذات الصلة

Texas Instruments LM211DRE4 LM211DG LM211QDR LP211DRE4 LM311DRE4 voltage comparator differential comparator analog comparator comparators semiconductor open-collector output propagation delay strobe input TTL-compatible output MOS-compatible output DTL RTL 8-pin SOIC SOIC family surface-mount package industrial control power-supply supervision test and measurement single-supply operation
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر