LM211DRE4 - 115 ns Differential Comparator | Texas Instruments
MPN: LM211DRE4 ✓ AktifLM211DRE4 Genel Bakış
A voltage comparator is an analog interface IC that compares two input voltages and produces a logic-level output indicating which input is higher. The comparator belongs to the broader hierarchy of analog comparator, analog IC, and semiconductor. Unlike a general-purpose operational amplifier, the LM211DRE4 is optimized for fast threshold decisions, regenerative switching behavior, and direct interface with digital logic systems.
The LM211 family combines a differential input stage with an open-collector output and dedicated strobe control. Its 115 ns propagation response supports rapid level detection, while its wide supply range allows operation from ±15 V analog systems as well as 5 V logic rails. The open-collector output can sink logic-level current and can be pulled up for wired logic, relay interfaces, or lamp-driving arrangements.
The comparator's inputs can operate independently of system ground when split supplies are used, providing useful flexibility in legacy industrial and instrumentation circuits. Output levels are compatible with most TTL and MOS circuits, reducing the need for intermediate logic drivers. Two strobe inputs support latch-like control in test equipment, pulse-width systems, and switching networks where the output state must be actively enabled or disabled.
Typical applications include industrial control and automation, power-supply supervision, signal threshold detection, test and measurement instrumentation, relay or lamp interfaces, and legacy digital logic interfaces. The 8-pin SOIC package supports through-hole assembly and PCB layouts based on the standard SOIC footprint. The broad supply range also makes the device suitable for systems transitioning between older ±15 V equipment and newer single-rail electronics.
Designers should verify output pull-up voltage, sink current, input common-mode range, and strobe logic levels for the intended system. Because the output is open collector, an external pull-up resistor is normally required. Keep the comparator close to the sensed signal and logic interface to reduce susceptibility to noise and propagation-delay variation on long traces.
This page combines manufacturer specifications, practical circuit guidance, comparison parameters, and pin-compatible replacement information. It also distinguishes true drop-in options from related devices that require different output, timing, supply, or qualification behavior, helping engineers choose a replacement without overlooking circuit-level compatibility.
Drop-in alternatifler için LM211DRE4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM211DRE4 (aynı form faktörü ve ayağa oturma) — farklı olan Comparator Type, Output Type, Logic Compatibility, Operating Temperature Range, Output Drive Capability.
LM211DG
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM211QDR
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LP211DRE4
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LM311DRE4
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LM211DRE4 Maksimum Değerlendirmeler & Elektriksel Özellikler
| Comparator Type | Single differential voltage comparator with strobes |
| Propagation Delay | 115 ns |
| Supply Voltage Range | 3.5 V to 30 V |
| Single-Supply Operation | 5 V to 30 V |
| Split-Supply Operation | ±15 V |
| Çıkış Türü | Open collector |
| Logic Compatibility | TTL, MOS, DTL, and RTL compatible |
| Number of Channels | 1 channel |
| Paket | 8-pin SOIC |
| Pin Sayısı | 8 pins |
| Montaj Türü | Surface mount |
| İşletim Sıcaklığı Aralığı | -40°C to 85°C |
| Strobe Inputs | 2 strobe inputs |
| Output-Level Compatibility | Compatible with most TTL and MOS circuits |
| Load-Driving Capability | Capable of driving lamps or relays |
LM211DRE4 8-pin soic Pin Yapısı Kılavuzu
LM211DRE4 (8-pin soic paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: LM211DRE4.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LM211DRE4 için uygundur 6 uygulamas: Industrial Control Signal Conditioning, Power-Supply Overvoltage Detection, Test and Measurement Threshold Detection, Relay and Lamp Interface, Digital Logic Level Detection, Pulse Width and Timing Circuits.
Industrial Control Signal Conditioning
The LM211DRE4 fits industrial control circuits that convert an analog process signal into a fast logic decision. Its 115 ns propagation delay allows a threshold change to reach the controller before the next significant control interval, while the 3.5 V to 30 V supply range supports both 5 V logic systems and higher-voltage legacy control boards. Place the comparator close to the sensor interface and use the open-collector output with a pull-up matching the controller input. The principal trade-off is that the open-collector transition requires an RC-shaped rising edge, so the pull-up value and bus capacitance must be checked against timing requirements.
Önerilen
Power-Supply Overvoltage Detection
The LM211DRE4 can monitor a rectified or regulated rail and generate a digital fault signal when the monitored voltage crosses a reference threshold. Its wide 3.5 V to 30 V operating range allows use in systems with 5 V, 12 V, 24 V, or 30 V rails, while the 115 ns response rapidly identifies a threshold crossing. The sensing divider and reference must remain within the input common-mode limits, and the output pull-up should be connected to the system logic rail. Because the output is open collector, the topology supports wired fault signaling and fail-safe logic without adding a push-pull output driver.
Önerilen
Test and Measurement Threshold Detection
The LM211DRE4 is appropriate for laboratory and production-test circuits that need to decide whether a measured signal is above or below a selected threshold. A 115 ns response time helps preserve timing relationships in pulse, burst, or repetitive test sequences, and the TTL- and MOS-compatible output can trigger digital test equipment. The external pull-up resistor controls the high-state rise time and must be selected together with the input capacitance of the instrument. For instrumentation operating from split supplies, the family supports operation up to ±15 V, helping simplify legacy analog front ends while retaining a standard 8-pin SOIC footprint.
Önerilen
Relay and Lamp Interface
The LM211DRE4 can serve as the decision element preceding a relay or lamp because the Texas Instruments family is identified as capable of driving such loads. Its open-collector output can pull down the low side of a properly designed load circuit, while the 115 ns response provides rapid switching. A flyback diode is required across an inductive relay coil, and the supply and output ratings must accommodate the load's off-state voltage and current. The logic pull-up must remain active when the load is switched off, and the board layout should keep the high-current load path separate from the comparator's sensitive input and timing traces.
Önerilen
Digital Logic Level Detection
The LM211DRE4 can translate a changing analog voltage into a logic-compatible event for TTL, MOS, DTL, or RTL systems. The 115 ns response reduces timing uncertainty when the comparator is used as a pulse-edge or threshold detector, while its broad supply range supports both 5 V systems and higher-voltage legacy interfaces. The open-collector output requires an external pull-up, whose value sets the rise time and determines the permissible fan-out. Designers should verify the pull-up voltage against the receiving device, account for the output sink-current limit, and avoid excessive capacitance on the output node.
Önerilen
Pulse Width and Timing Circuits
The LM211DRE4 can form part of pulse-width and timing circuits because its 115 ns propagation delay is short enough for many legacy control and instrumentation systems. The strobe inputs allow a surrounding logic network to enable or inhibit the comparison at defined moments, supporting gated acquisition and repeatable measurement sequences. The open-collector output can feed a counter, timer, or latch through a pull-up resistor, although the resistor-capacitor network introduces a deliberate rise-time limit. Circuit simulation should include the pull-up value, wiring capacitance, and input overdrive because these factors can dominate the apparent switching time.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM211DRE4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM211DG | LM211QDR | LP211DRE4 | LM311DRE4 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Comparator Type | Single differential comparator with strobes | Single differential comparator with strobes | Single differential comparator with strobes | Single differential comparator | Single differential comparator with strobes |
| Propagation Delay | 115 ns | 115 ns | 115 ns | Approximately 200 ns | Approximately 200 ns |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
Ana Farklılayıcılar
- Faster response than the LM311-family alternative (karşılaştırma:LM311DRE4)
- Faster response than the LP211-family alternative (karşılaştırma:LP211DRE4)
- Closest same-family pin-compatible sourcing options (karşılaştırma:LM211QDR)
- Wide supply support within the same SOIC footprint (karşılaştırma:LM211DG)
Tasarım Notları
The output is open collector and therefore requires an external pull-up resistor for normal high-state operation. Select the resistor using the receiving logic's high-level voltage, the LM211 sink-current limit, bus capacitance, and the required rising-edge time. Avoid using an excessively large pull-up, because it can slow transitions and make the circuit susceptible to noise; avoid an excessively small pull-up, because it can overload the output transistor.
Place the comparator, its input resistor network, and the output pull-up resistor close to the device, particularly when the input is a high-impedance sensing node. Keep the pull-up and load-current return path physically separated from the input and reference traces to reduce supply transients and ground bounce. Route strobe signals away from the differential input pair, and use a stable ground reference for both the sensing divider and comparator.
A 115 ns propagation delay applies to the comparator's specified operating conditions, but practical switching time also depends on input overdrive, source impedance, output pull-up resistance, and load capacitance. Check the maximum overdrive needed for consistent timing and include output rise time in pulse-width calculations. For fast edges or long PCB traces, use a local receiver or buffer rather than assuming the nominal delay describes the complete signal transition.
Verify that the selected supply remains within the 3.5 V to 30 V operating range in every operating state. If the output pull-up is connected to a rail different from the comparator supply, ensure that rail is present before the LM211DRE4 can pull the output low. Decouple the supply near pin 8 with a short, low-inductance path, and avoid routing load-return current through the comparator's ground reference.
Uyumluluk Bilgisi
The E4 ordering code is associated with lead-free assembly nomenclature, but explicit RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 declarations require confirmation in the current manufacturer documentation.