LM258DR2 - Dual 3-32V Op Amp | onsemi | 8-SOIC IC
MPN: LM258DR2 ✓ نشطLM258DR2 نظرة عامة
An operational amplifier is an analog building block that compares two input voltages and amplifies the difference between them. The LM258 belongs to the dual-operational-amplifier hierarchy within linear amplifier ICs and broader semiconductor devices. Its two channels can amplify or buffer independent signals within one package, reducing board area compared with separate single-channel amplifiers while preserving familiar industry-standard pin assignments.
The LM258DR2 emphasizes low power drain, operation from a single 3 V to 32 V supply, and common-mode input operation toward ground or VEE. These characteristics make it useful in battery-powered instrumentation, industrial control systems, sensor-conditioning circuits, audio preamplifiers, and general feedback networks. The dual configuration also allows related channels to be used as an amplifier and buffer within the same package.
With a gain-bandwidth product of 700 kHz, the LM258 is suited to moderate-bandwidth analog signal paths rather than high-speed or precision applications requiring substantially greater bandwidth or lower offset. The split-supply capability permits operation around a midpoint reference, while the single-supply mode supports systems where the signal remains near the lower supply rail. Input, output, and supply limits must be respected during design.
Typical uses include low-frequency sensor amplification, audio signal conditioning, audio preamplifiers, active filters, comparators with added feedback, and industrial process-control interfaces. The LM258DR2 is particularly suitable when two conventional amplifier channels are needed without the extra operating supply or board area associated with dual-rail-only precision amplifiers.
Designers should preserve the standard SOIC-8 footprint and verify the manufacturer's pin-description table before routing the PCB. Input common-mode and output swing limits depend on the selected supply voltage and load. Decoupling close to the supply pins, adequate output-current capacity, and stable feedback compensation are essential for dependable operation.
This product page combines package, application, pinout, sourcing, and replacement guidance with practical design considerations. It also distinguishes verified device attributes from parameters that require confirmation with the manufacturer datasheet before release to production.
بدائل مباشرة لـ LM258DR2 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM258DR2 (نفس عامل الشكل والبصمة) — يختلف في Common-Mode Input Range, Product Classification, REACH Status, RoHS Status.
LM258DR2G
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM258DR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM158DT
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LM358YD
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LM258DR2 الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 3 V to 32 V |
| Gain-Bandwidth Product | 700 kHz |
| Supply Configuration | Single supply or split supply |
| Common-Mode Input Range | Extends to ground or VEE |
| Power Consumption | Low power drain |
| العلبة | 8-pin SOIC |
| نوع التركيب | Surface mount |
تكوين أطراف LM258DR2
| دبوس 1 | OUT1 — Channel 1 output |
| دبوس 2 | IN1- — Channel 1 inverting input |
| دبوس 3 | IN1+ — Channel 1 non-inverting input |
| دبوس 4 | V- — Negative supply or ground connection |
| دبوس 5 | IN2+ — Channel 2 non-inverting input |
| دبوس 6 | IN2- — Channel 2 inverting input |
| دبوس 7 | OUT2 — Channel 2 output |
| دبوس 8 | V+ — Positive supply connection |
التطبيقات النموذجية
LM258DR2 مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Audio Preamplifier, Active Feedback Filter, Battery-Powered Instrumentation, Process Control Interface, Comparator with Feedback.
Industrial Sensor Signal Conditioning
The LM258DR2 is appropriate for amplifying low-bandwidth sensor signals in industrial measurement circuits because its 3 V to 32 V supply range supports both compact low-voltage systems and higher-voltage industrial rails. The two channels can condition or buffer related signals while sharing an 8-pin SOIC footprint. The onsemi LM258 datasheet identifies low power drain, split- or single-supply operation, and common-mode input operation extending to ground or VEE. Before deployment, verify the input offset, bias current, noise, output swing, and common-mode limits against the sensor output and production temperature range.
موصى به
Audio Preamplifier
The LM258DR2 can provide two general-purpose amplifier channels for an audio preamplifier or line-level conditioning stage. Its 700 kHz gain-bandwidth product is suitable for many conventional low-to-moderate-bandwidth audio paths, while low power drain is useful in portable or space-constrained equipment. The dual SOIC package reduces board area by combining two functions in one component. Confirm output headroom, slew rate, noise, and channel-to-channel behavior in the manufacturer electrical-characteristics table, especially when driving a load through an additional output stage.
موصى به
Active Feedback Filter
The LM258DR2 suits active feedback networks that require conventional amplification within a 700 kHz gain-bandwidth capability. Its two independent channels allow designers to implement sections such as first-order or modest multi-stage filters, depending on the selected topology and component tolerances. The common-mode input range extending toward ground or VEE supports single-supply filter designs in which signals operate near the lower rail. Verify stability, gain-bandwidth margin, output loading, and exact frequency-response targets before treating the circuit as production-ready.
موصى به
Battery-Powered Instrumentation
The LM258DR2 works well as a general-purpose dual amplifier in battery-powered instrumentation because the manufacturer describes low power drain and supports a 3 V minimum supply voltage. Two channels can be used for signal conditioning and buffering without using two separate IC packages. Operation from a single supply simplifies power architecture, and the common-mode input capability extending toward ground or VEE supports sensors with limited output swing. Determine actual battery-life impact from the supply-current conditions, output state, load, and temperature rather than using the low-power-drain description alone.
موصى به
Process Control Interface
The LM258DR2 is suitable for process-control interface stages that condition a sensor signal before an ADC, controller, or actuator driver. Its 3 V to 32 V operating range accommodates both compact embedded electronics and industrial control systems, while split-supply operation allows signal handling around a biased reference. The two channels can support related gain and buffering functions. Ensure the selected operating point remains within the input common-mode and output swing limits, and assess offset, drift, noise, and overload recovery against the control-loop accuracy requirement.
موصى به
Comparator with Feedback
The LM258DR2 can operate as a comparator when feedback is used to create a defined output state rather than relying on open-loop saturation behavior. This arrangement can provide threshold detection or limiting in low-bandwidth control and signal-conditioning systems. Its two channels allow one stage to perform buffering or amplification before the threshold stage. The 3 V to 32 V supply range supports varied rail conditions, while low power drain is beneficial in embedded systems. Review input overvoltage, output saturation, propagation behavior, and stability in the manufacturer documentation before applying this configuration.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM258DR2 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM258DR2G | LM258DR | LM158DT | LM358YD |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments | STMicroelectronics |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Special Positioning | General-purpose LM258 family device | Closest onsemi LM258 ordering variant | Texas Instruments LM258 family device | Precision LM158 family device | General-purpose LM358 family device |
أبرز الفروقات
- Direct onsemi family ordering alternative (مقابلLM258DR2G)
- Broad single-supply operating range (مقابلLM358YD)
- Published 700 kHz bandwidth target (مقابلLM158DT)
- Single-supply common-mode operation (مقابلLM158DT)
ملاحظات التصميم
Place the device to match the standard 8-pin SOIC footprint and preserve clearance around pins 4 and 8 for the supply connections. Follow the manufacturer pin-description table when assigning input, output, and supply nets. A ground or supply-return plane close to the IC can reduce loop area, but high-current return paths should remain separate from sensitive input nodes to prevent shared-impedance disturbance.
The LM258DR2 supports single- and split-supply operation across a 3 V to 32 V range. In single-supply designs, keep the signal within the usable common-mode and output-swing limits rather than assuming the full supply range appears at the output. In split-supply designs, connect V- to the intended negative rail and confirm that every connected node remains within the absolute maximum input and output limits.
Do not use the generic LM258 name to assume that every ordering suffix has identical temperature, qualification, compliance, or lifecycle characteristics. Review the exact onsemi suffix, electrical table, package drawing, and ordering information for LM258DR2. Also avoid replacing the device solely because another dual amplifier uses an 8-SOIC package; check pin functions and compare offset, bias current, bandwidth, slew rate, output swing, and supply limits.
Keep feedback resistors and compensation components close to the relevant amplifier pins, and route sensitive non-inverting inputs away from supply and output nodes. When both channels are used, evaluate their grounding and feedback networks independently so current in one channel does not create voltage disturbance in the other. A solid return plane and short supply-decoupling path help preserve predictable behavior in low-bandwidth analog systems.
معلومات الامتثال
The LM258 family is a general-purpose operational amplifier rather than an automotive-qualified device. Exact suffix-specific environmental and material compliance must be confirmed with onsemi before production release.