LM2901NG - 3-36 V Quad Comparator for Level Detection | onsemi
MPN: LM2901NG ✓ نشطLM2901NG نظرة عامة
A quad comparator is a multi-channel analog semiconductor that decides whether one input voltage is above or below another reference voltage. The LM2901NG belongs to the comparator hierarchy, where a comparator is a signal-conditioning IC used to produce a digital, logic-level decision from two analog voltages. Its four independent channels allow a compact circuit to monitor several thresholds, levels, or memory-control signals without requiring four separate comparator packages.
The principal features include a 3 V to 36 V supply range, single-supply operation, and a low output saturation voltage of 130 mV at 4 mA. The common-mode input range includes ground, making the device practical for single-supply systems in which signals remain near the lower rail. ESD input clamps improve reliability without changing normal comparator operation, while the open-collector outputs permit wired logic, pull-up resistor selection, and compatibility with multiple logic families.
Within the LM2901 family, the NG suffix identifies the onsemi 14-pin PDIP configuration. The device provides four separate comparator channels rather than a single comparison function, reducing package count when several independent decisions are required. Its open-collector outputs require an external pull-up when the output must rise to a defined positive voltage. Designers should account for the pull-up value, output leakage, input bias current, and propagation delay when driving long interconnects or switching high-capacitance nodes.
Typical applications include industrial sensor threshold detection, battery-powered equipment, memory-control logic, window or level comparators, and general-purpose TTL or CMOS interfacing. Because the operating range extends to 36 V, the LM2901NG can be used in higher-voltage industrial systems when every input remains inside its permitted common-mode range. The -40°C to 105°C temperature range supports both commercial and extended industrial environments.
For reliable operation, use the pin-description table and typical application information in the onsemi datasheet when assigning input polarities and output pull-ups. Keep sensitive analog input traces away from high-current switching nodes, provide a stable local supply connection, and select a pull-up resistor that balances rise time against output-driver loading. Input and output filtering may be required when the comparator is used near switching regulators or fast digital signals.
This product page combines the manufacturer specifications with package, application, comparison, and design guidance for engineers evaluating LM2901NG. It also identifies qualified same-package alternatives and highlights the electrical and application trade-offs that should be checked before a replacement is approved for an existing PCB.
بدائل مباشرة لـ LM2901NG — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM2901NG (نفس عامل الشكل والبصمة) — يختلف في Comparator Type, Mounting Type, Package, Output Type, Supply Configuration.
LM2901SNG
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LM2901NG4
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2901N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2901M
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2901A
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LM2901NG الحدود القصوى والخصائص الكهربائية
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 36 V |
| Supply Configuration | Single supply |
| نوع الخرج | Open collector |
| Logic Compatibility | TTL and CMOS |
| Output Saturation Voltage | 130 mV at 4 mA |
| Common-Mode Input Range | Includes ground |
| نطاق درجة حرارة التشغيل | -40°C to 105°C |
| Input ESD Protection | ESD clamps on inputs |
| Package Type | 14-pin PDIP |
| نوع التركيب | Through-hole |
| Manufacturer | onsemi |
| Device Classification | Standard general-purpose comparator |
| Typical Applications | Level detection, low-level sensing, and memory applications |
تكوين أطراف LM2901NG
| دبوس 1 | OUT1 — Comparator 1 open-collector output |
| دبوس 2 | IN1- — Comparator 1 inverting input |
| دبوس 3 | IN1+ — Comparator 1 non-inverting input |
| دبوس 4 | GND — Ground connection |
| دبوس 5 | IN2+ — Comparator 2 non-inverting input |
| دبوس 6 | IN2- — Comparator 2 inverting input |
| دبوس 7 | OUT2 — Comparator 2 open-collector output |
| دبوس 8 | OUT3 — Comparator 3 open-collector output |
| دبوس 9 | IN3- — Comparator 3 inverting input |
| دبوس 10 | IN3+ — Comparator 3 non-inverting input |
| دبوس 11 | V+ — Positive supply connection |
| دبوس 12 | IN4+ — Comparator 4 non-inverting input |
| دبوس 13 | IN4- — Comparator 4 inverting input |
| دبوس 14 | OUT4 — Comparator 4 open-collector output |
التطبيقات النموذجية
LM2901NG مناسب لـ 6 التطبيقs: Industrial Sensor Threshold Detection, Battery-Powered Monitoring Circuit, Memory Control and Logic Interface, TTL and CMOS Logic Interfacing, Automotive and Robust Control Systems, General-Purpose Signal Conditioning.
Industrial Sensor Threshold Detection
The onsemi LM2901NG is well suited to industrial threshold detection because its four independent channels can compare multiple sensor signals with reference voltages while operating from a 3 V to 36 V supply. The common-mode input range includes ground, which helps when a sensor output is referenced to the lower supply rail. Each open-collector output can drive a pull-up and alarm or logic input. The 130 mV saturation voltage at 4 mA provides a low output level for digital interfacing. Designers should verify that sensor voltages remain within the permitted input range, account for input bias current, and place the comparator close enough to sensitive analog nodes to reduce pickup from industrial switching equipment.
موصى به
Battery-Powered Monitoring Circuit
LM2901NG can implement multiple low-level monitoring functions in battery-operated equipment because it combines four comparison channels with a supply range starting at 3 V. A battery system can use the channels to detect a falling supply level, compare a control voltage with a threshold, or supervise two independent signals. The common-mode input range including ground supports measurements near the lower rail. Because the outputs are open collector, pull-up resistors can define the logic-high voltage independently of the comparator's supply. Keep the pull-up load within the output sink-current rating and calculate its maximum value from battery current, output leakage, and the capacitance of the connected logic input.
موصى به
Memory Control and Logic Interface
The LM2901NG's four differential channels are useful for memory-control logic where several voltage thresholds must be translated into hardware control signals. Each channel can compare a data or control voltage against a reference and provide an open-collector result suitable for wired logic. Its ground-inclusive common-mode range is helpful in systems whose signals are referenced close to 0 V, while the 3 V to 36 V supply range accommodates different logic environments. Timing margins should be checked against the memory interface, and pull-up resistors should be selected to provide adequate rise time without excessive supply current. Input overshoot and ringing should also be evaluated at board level.
موصى به
TTL and CMOS Logic Interfacing
LM2901NG provides four open-collector outputs that can interface with TTL or CMOS logic when an appropriate pull-up network is used. A pull-up to the receiving logic rail creates a valid high level, while the comparator sinks the node low. The specified 130 mV saturation voltage at 4 mA indicates the low-level behavior needed by many digital systems. Choose the pull-up resistor using the load current, input capacitance, output leakage, and allowable transition rate. The four-channel package reduces component count in boards requiring several independent digital decisions, although each open-collector output must be evaluated separately for fan-out and rise-time requirements.
موصى به
Automotive and Robust Control Systems
The LM2901NG's -40°C to 105°C operating range and 3 V to 36 V supply capability make it a candidate for robust control and monitoring circuits spanning wide environmental conditions. Four channels can supervise several vehicle, actuator, or machine-control thresholds without using four separate IC packages. The ground-inclusive common-mode range supports single-supply sensing architectures, while open-collector outputs permit flexible pull-up arrangements. Automotive production use requires separate confirmation of the exact suffix, qualification status, quality documentation, and any customer-specific requirements. Signal conditioning should prevent transient voltages and ground offsets from pushing an input outside the limits published by the manufacturer.
موصى به
General-Purpose Signal Conditioning
LM2901NG is useful as a general-purpose signal conditioner for analog nodes that must become deterministic logic decisions. A designer can compare a conditioned sensor output, rectified waveform, or reference voltage against an adjustable threshold and use the open-collector result to drive an indicator, relay-control stage, or digital input. Its four independent channels allow several measurements to be handled in one through-hole package. For best results, minimize input-node capacitance, keep comparator traces away from switching-current paths, and verify propagation delay against the timing requirement. The pull-up resistor should create a clean rising edge without causing excessive overshoot when the open-collector transistor turns off.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM2901NG — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM2901SNG | LM2901NG4 | LM2901N | LM2901M | LM2901A |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments | onsemi | 3PEAK |
| Package | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
أبرز الفروقات
- Four independent threshold channels in one 14-pin package (مقابلLM2901N)
- Ground-inclusive common-mode operation for single-supply designs (مقابلLM2901A)
- Specified low output saturation for digital interfacing (مقابلLM2901NG4)
- Wide supply capability for industrial monitoring (مقابلLM2901SNG)
ملاحظات التصميم
Route each inverting and non-inverting input as a short, quiet analog trace, especially where the comparator detects small voltage differences. Keep these paths away from power-switching nodes, relay contacts, high-current return paths, and high-impedance sensor outputs. Place the device near the protected signal and connect its ground pin to the quiet analog ground reference used by the signal source.
Design every open-collector output with an external pull-up connected to the logic rail that defines the required high voltage. Estimate the maximum pull-up current as the logic-high voltage divided by the pull-up resistance, and verify that it remains within the output sink-current capability. A smaller resistor reduces rise time but increases current; a larger resistor lowers power consumption but can slow transitions and increase susceptibility to leakage and noise.
Do not assume that the entire 3 V to 36 V supply range is also a valid common-mode input range. Confirm both positive and negative input limits against the onsemi datasheet, including transient excursions and offsets caused by source impedance. For a single-supply design, keep the non-inverting reference near the lower end of the allowed range and account for input bias current when generating that reference with a high-value divider.
If the comparator drives a cable, long trace, or high-capacitance node, calculate the pull-up-induced rise time using the resistor and total capacitance. Excessive capacitance can slow the rising edge and create ringing when the open-collector output switches off. Use a staged driver, lower pull-up resistance within the sink-current limit, or a Schmitt-trigger input stage when slow edges would cause multiple transitions.
The LM2901NG is a comparator rather than a power regulator, but its supply dissipation still depends on output duty cycle and pull-up current. Estimated: with a 5 V pull-up and a 4 mA low-state sink current, the output transistor dissipates approximately 20 mW while low. Confirm the actual output duty cycle, ambient temperature, and PCB copper area against the manufacturer's maximum ratings.
معلومات الامتثال
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was established for the exact LM2901NG ordering code. Request current compliance and quality documentation through the Request a Quote form.