LM2903N-NS - Dual Precision Comparator | onsemi
MPN: LM2903N-NS ✓ نشطLM2903N-NS نظرة عامة
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 family belongs to the broader comparator category within analog and mixed-signal semiconductors. Unlike an operational amplifier used primarily for linear amplification, each LM2903N-NS channel provides a binary decision function. The open-collector outputs permit wired logic, pull-up arrangements, level translation, and connection to external pull-up networks.
The two internal channels are independent, allowing them to perform separate threshold, window, or protection functions without sharing signal paths. Low input offset is important when the two compared voltages are close, because excessive offset can shift the switching threshold and create errors in precision monitoring. The family was specifically designed for single-supply operation over a wide voltage range, while split-supply operation is also supported. Its supply-current drain is independent of the magnitude of the applied supply voltage.
The LM2903N-NS combines two independent precision comparators in one through-hole package. Open-collector outputs require suitable pull-up resistors or suitable pull-up logic to establish a valid high output state. Because the output stage is open collector, multiple comparator outputs can be combined when the application supports wired-AND behavior and the electrical conditions remain within the device ratings. Common-mode input limits, supply voltage limits, output sink-current limits, and input-current limits must still be respected.
Typical uses include industrial sensor interfaces, battery and power-system monitoring, control systems, threshold detection, overvoltage and undervoltage protection, and general digital logic interfacing. The dual-channel organization is especially useful when two independent thresholds must be monitored in the same circuit. A single package also reduces board area compared with two separate single comparators while retaining straightforward through-hole assembly.
For reliable operation, connect unused comparator inputs to a defined potential so they do not float near the switching threshold. Place the input and output pull-up network close to the relevant pins, and check that the external pull-up voltage does not exceed the allowed output and supply limits. The comparator normally responds to an input crossing, so hysteresis or positive feedback may be needed to prevent repeated output transitions when the compared signals are nearly equal.
This product page combines the family-level electrical description, package and pin information, sourcing guidance, compatible alternatives, and practical design notes. It also distinguishes true same-footprint replacements from alternatives that require PCB changes, helping engineers assess upgrade options before committing a design to production.
بدائل مباشرة لـ LM2903N-NS — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM2903N-NS (نفس عامل الشكل والبصمة) — يختلف في Output Type, Package, Comparator Type, Input Offset Voltage, Operating Temperature Range.
LM2903N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2903N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2903N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2903N/NOPB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2903N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2903N-NS الحدود القصوى والخصائص الكهربائية
| Comparator Count | 2 independent channels |
| Device Type | Dual precision voltage comparator |
| نوع الخرج | Open collector |
| Supply Operation | Single supply or split supply |
| Input Offset Voltage | 2.0 mV maximum for the LM193/LM2903 family |
| Single-Supply Common-Mode Range | Extends to ground |
| تيار التغذية | Independent of supply-voltage magnitude |
| العلبة | 8-pin PDIP |
| نوع التركيب | Through-hole |
تكوين أطراف LM2903N-NS
| دبوس 1 | OUT1 — Channel 1 open-collector output |
| دبوس 2 | IN1- — Channel 1 inverting input |
| دبوس 3 | IN1+ — Channel 1 non-inverting input |
| دبوس 4 | GND — Ground connection |
| دبوس 5 | IN2+ — Channel 2 non-inverting input |
| دبوس 6 | IN2- — Channel 2 inverting input |
| دبوس 7 | OUT2 — Channel 2 open-collector output |
| دبوس 8 | VCC — Positive supply connection |
التطبيقات النموذجية
LM2903N-NS مناسب لـ 6 التطبيقs: Industrial Sensor Threshold Detection, Battery Power-Supply Protection, Voltage-Window Monitor, Overcurrent and Overvoltage Protection, Control-System Limit Switch, Open-Collector Logic Interfacing.
Industrial Sensor Threshold Detection
The LM2903N-NS fits industrial sensor interfaces that require two independent threshold decisions, such as a pressure or temperature transducer whose signal must be checked against upper and lower limits. Its two precision comparator channels can evaluate separate sensor nodes while operating from a single supply whose common-mode range extends toward ground. Each channel compares a sensor signal with a reference and produces an open-collector logic indication. Adding controlled positive feedback creates hysteresis and reduces repeated switching near the threshold. The onsemi LM2903N datasheet remains the controlling document for exact input limits, offset conditions, and output-current capability.
موصى به
Battery Power-Supply Protection
The LM2903N-NS is useful in battery-powered systems where separate circuits must detect undervoltage and overvoltage conditions around a battery rail. Because the package contains two independent comparators, one channel can monitor the battery against a lower reference while the other checks a higher limit. The open-collector outputs can drive pull-up logic, fault indicators, or a system shutdown input without requiring a push-pull driver. Designers should account for the battery’s operating range, comparator input limits, and supply-current requirements. The onsemi LM2903N datasheet defines the exact electrical boundaries for the selected ordering code.
موصى به
Voltage-Window Monitor
The LM2903N-NS fits voltage-window monitoring circuits that must declare both undervoltage and overvoltage conditions. The two independent channels compare the monitored rail with separate upper and lower thresholds, while their open-collector outputs can be pulled up to a system-compatible logic voltage. When the rail is between the thresholds, the outputs can represent an in-range state; outside the range, either output can change state. Practical implementation requires resistor tolerances to be included in threshold-error analysis and may require positive feedback to prevent chatter near each limit. The onsemi LM2903N datasheet supplies the applicable input and output limitations.
موصى به
Overcurrent and Overvoltage Protection
The LM2903N-NS can implement independent protection decisions in power-conversion control boards. One comparator channel may monitor a scaled voltage representing output current, while the second evaluates an overvoltage signal. Both channels operate from the local control supply and provide open-collector fault indications that can be pulled up and combined by the controller. This arrangement avoids using two separate single-channel packages, although each decision path still requires careful reference design, filtering, and propagation-delay analysis. The onsemi LM2903N datasheet should be used to confirm common-mode limits, saturation behavior, and the permissible output sink current.
موصى به
Control-System Limit Switch
The LM2903N-NS is appropriate for general industrial control logic that converts an analog process variable into a limit-switch signal. One channel can compare the process signal with a setpoint, while the other can perform a secondary condition such as a guard-band or enable check. A pull-up resistor establishes the open-collector output’s inactive state, allowing the result to connect to TTL, CMOS, or another controller interface if the voltage and current limits are respected. Hysteresis is important when the process signal has ripple or noise. The onsemi LM2903N datasheet provides the authoritative electrical limits for the onsemi ordering code.
موصى به
Open-Collector Logic Interfacing
The LM2903N-NS supports open-collector logic interfacing because its outputs can pull a shared bus low while external pull-up resistors establish the high state. This arrangement can connect a comparator decision to a wired-AND function, isolate a fault line, or translate a system voltage through the pull-up network. Two independent channels provide flexibility when one event must acknowledge or mask another. The design must verify that the aggregate sink current of all connected outputs remains within the device limit and that the pull-up voltage is permissible. The onsemi LM2903N datasheet gives the output-current and electrical-characteristic criteria for that assessment.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM2903N-NS — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM2903N | LM2903N | LM2903N | LM2903N/NOPB | LM2903N |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | STMicroelectronics | NXP Semiconductors | Texas Instruments | HGSEMI |
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Comparator Count | 2 independent channels | 2 independent channels | 2 independent channels | 2 independent channels | 2 independent channels | 2 independent channels |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Supply Operation | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
| Pin Count | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
أبرز الفروقات
- Two independent precision comparator channels in one package (مقابلLM2901M)
- Open-collector output supports wired logic and flexible pull-up voltage (مقابلTLV7022)
- Single-supply common-mode operation extends toward ground (مقابلLM2902N/PB)
ملاحظات التصميم
Do not treat the open-collector output as a push-pull logic output. Each output requires a pull-up resistor or suitable pull-up logic before it can present a valid high state. Size the resistor from the required sink current and desired rise time, and verify that simultaneous low outputs do not exceed the device's total output-current limit. The onsemi LM2903N datasheet defines the applicable output constraints.
Add intentional hysteresis when either input can vary slowly or carry noise. A small positive-feedback resistor from an output to its non-inverting input separates the switching thresholds and prevents repeated transitions around the reference voltage. Check that this feedback does not distort the intended threshold or exceed the output-current limit, especially when both channels share the same reference network.
Keep the comparator inputs and their reference components away from switching-power nodes and high-current return paths. Place the open-collector pull-up resistors close to the output pins to minimize trace area and ringing. Maintain a low-impedance ground return for pin 4, and review the complete common-mode and supply ranges before connecting a sensor whose output may exceed the comparator input limits.
Decouple the supply pin near the package with the capacitance recommended by the manufacturer, and account for the fact that the family supply-current drain is independent of supply-voltage magnitude. Do not assume a comparator output can safely sink the pull-up current at every supply voltage; calculate the worst-case sink condition and account for temperature-dependent output characteristics.
معلومات الامتثال
Exact onsemi LM2903N-NS material-compliance declarations were not identified. Automotive qualification is not claimed for the standard LM2903N-NS ordering code.