onsemi

LM2903N-NS - Dual Precision Comparator | onsemi

MPN: LM2903N-NS ✓ सक्रिय
Single supply or split supply Vdss Independent of supply-voltage magnitude Id 8-pin PDIP Package
न्यूनतम ऑर्डर मात्रा: 1 |

LM2903N-NS अवलोकन

The onsemi LM2903N-NS is a dual, independent precision voltage comparator with open-collector outputs, supplied in an 8-pin PDIP package. It contains two separate comparator channels, an input offset voltage specified as low as 2.0 mV maximum for the LM193/LM2903 family, and operation from either a single supply or split supplies. Its single-supply common-mode capability extends down to ground, making it useful for systems that monitor signals referenced to the supply rail.

A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 family belongs to the broader comparator category within analog and mixed-signal semiconductors. Unlike an operational amplifier used primarily for linear amplification, each LM2903N-NS channel provides a binary decision function. The open-collector outputs permit wired logic, pull-up arrangements, level translation, and connection to external pull-up networks.

The two internal channels are independent, allowing them to perform separate threshold, window, or protection functions without sharing signal paths. Low input offset is important when the two compared voltages are close, because excessive offset can shift the switching threshold and create errors in precision monitoring. The family was specifically designed for single-supply operation over a wide voltage range, while split-supply operation is also supported. Its supply-current drain is independent of the magnitude of the applied supply voltage.

The LM2903N-NS combines two independent precision comparators in one through-hole package. Open-collector outputs require suitable pull-up resistors or suitable pull-up logic to establish a valid high output state. Because the output stage is open collector, multiple comparator outputs can be combined when the application supports wired-AND behavior and the electrical conditions remain within the device ratings. Common-mode input limits, supply voltage limits, output sink-current limits, and input-current limits must still be respected.

Typical uses include industrial sensor interfaces, battery and power-system monitoring, control systems, threshold detection, overvoltage and undervoltage protection, and general digital logic interfacing. The dual-channel organization is especially useful when two independent thresholds must be monitored in the same circuit. A single package also reduces board area compared with two separate single comparators while retaining straightforward through-hole assembly.

For reliable operation, connect unused comparator inputs to a defined potential so they do not float near the switching threshold. Place the input and output pull-up network close to the relevant pins, and check that the external pull-up voltage does not exceed the allowed output and supply limits. The comparator normally responds to an input crossing, so hysteresis or positive feedback may be needed to prevent repeated output transitions when the compared signals are nearly equal.

This product page combines the family-level electrical description, package and pin information, sourcing guidance, compatible alternatives, and practical design notes. It also distinguishes true same-footprint replacements from alternatives that require PCB changes, helping engineers assess upgrade options before committing a design to production.

के लिए ड्रॉप-इन विकल्प LM2903N-NS — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM2903N-NS (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Output Type, Package, Comparator Type, Input Offset Voltage, Operating Temperature Range.

Texas Instruments
Output Type: Open-Collector / Open-Drain
Package: 8-Pin PDIP (DIP-8, N suffix)
Comparator Type: Low Offset Voltage, Dual Differential
इसके साथ तुलना करें LM2903N-NS →
Texas Instruments
Output Type: Open collector / open drain
Package: 8-pin PDIP (P)
Comparator Type: Dual differential comparator

LM2903N

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Low Offset Voltage, Dual Differential · 2 (dual independent) · Open-Collector / Open-Drain · 2 V to 36 V · ±1 V to ±18 V · 2.5 mV (LM2903 grade) · 25 nA · Includes ground (negative rail)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2903N

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Low Offset Voltage, Dual Differential · 2 (dual independent) · Open-Collector / Open-Drain · 2 V to 36 V · ±1 V to ±18 V · 2.5 mV (LM2903 grade) · 25 nA · Includes ground (negative rail)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2903N

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Low Offset Voltage, Dual Differential · 2 (dual independent) · Open-Collector / Open-Drain · 2 V to 36 V · ±1 V to ±18 V · 2.5 mV (LM2903 grade) · 25 nA · Includes ground (negative rail)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2903N/NOPB

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Dual differential comparator · 2 channels · Open collector / open drain · 36 V · 2 mV maximum · 1.3 microseconds

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2903N

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Low Offset Voltage, Dual Differential · 2 (dual independent) · Open-Collector / Open-Drain · 2 V to 36 V · ±1 V to ±18 V · 2.5 mV (LM2903 grade) · 25 nA · Includes ground (negative rail)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2903N-NS Maximum Ratings और Electrical Characteristics

Comparator Count 2 independent channels
Device Type Dual precision voltage comparator
आउटपुट प्रकार Open collector
Supply Operation Single supply or split supply
Input Offset Voltage 2.0 mV maximum for the LM193/LM2903 family
Single-Supply Common-Mode Range Extends to ground
सप्लाई करंट Independent of supply-voltage magnitude
पैकेज 8-pin PDIP
माउंटिंग प्रकार Through-hole

LM2903N-NS पिन कॉन्फ़िगरेशन

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
पिन 1 OUT1 — Channel 1 open-collector output
पिन 2 IN1- — Channel 1 inverting input
पिन 3 IN1+ — Channel 1 non-inverting input
पिन 4 GND — Ground connection
पिन 5 IN2+ — Channel 2 non-inverting input
पिन 6 IN2- — Channel 2 inverting input
पिन 7 OUT2 — Channel 2 open-collector output
पिन 8 VCC — Positive supply connection

सामान्य अनुप्रयोग

LM2903N-NS के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Threshold Detection, Battery Power-Supply Protection, Voltage-Window Monitor, Overcurrent and Overvoltage Protection, Control-System Limit Switch, Open-Collector Logic Interfacing.

🏭

Industrial Sensor Threshold Detection

The LM2903N-NS fits industrial sensor interfaces that require two independent threshold decisions, such as a pressure or temperature transducer whose signal must be checked against upper and lower limits. Its two precision comparator channels can evaluate separate sensor nodes while operating from a single supply whose common-mode range extends toward ground. Each channel compares a sensor signal with a reference and produces an open-collector logic indication. Adding controlled positive feedback creates hysteresis and reduces repeated switching near the threshold. The onsemi LM2903N datasheet remains the controlling document for exact input limits, offset conditions, and output-current capability.

⚡

Battery Power-Supply Protection

The LM2903N-NS is useful in battery-powered systems where separate circuits must detect undervoltage and overvoltage conditions around a battery rail. Because the package contains two independent comparators, one channel can monitor the battery against a lower reference while the other checks a higher limit. The open-collector outputs can drive pull-up logic, fault indicators, or a system shutdown input without requiring a push-pull driver. Designers should account for the battery’s operating range, comparator input limits, and supply-current requirements. The onsemi LM2903N datasheet defines the exact electrical boundaries for the selected ordering code.

📺

Voltage-Window Monitor

The LM2903N-NS fits voltage-window monitoring circuits that must declare both undervoltage and overvoltage conditions. The two independent channels compare the monitored rail with separate upper and lower thresholds, while their open-collector outputs can be pulled up to a system-compatible logic voltage. When the rail is between the thresholds, the outputs can represent an in-range state; outside the range, either output can change state. Practical implementation requires resistor tolerances to be included in threshold-error analysis and may require positive feedback to prevent chatter near each limit. The onsemi LM2903N datasheet supplies the applicable input and output limitations.

🔧

Overcurrent and Overvoltage Protection

The LM2903N-NS can implement independent protection decisions in power-conversion control boards. One comparator channel may monitor a scaled voltage representing output current, while the second evaluates an overvoltage signal. Both channels operate from the local control supply and provide open-collector fault indications that can be pulled up and combined by the controller. This arrangement avoids using two separate single-channel packages, although each decision path still requires careful reference design, filtering, and propagation-delay analysis. The onsemi LM2903N datasheet should be used to confirm common-mode limits, saturation behavior, and the permissible output sink current.

⚙️

Control-System Limit Switch

The LM2903N-NS is appropriate for general industrial control logic that converts an analog process variable into a limit-switch signal. One channel can compare the process signal with a setpoint, while the other can perform a secondary condition such as a guard-band or enable check. A pull-up resistor establishes the open-collector output’s inactive state, allowing the result to connect to TTL, CMOS, or another controller interface if the voltage and current limits are respected. Hysteresis is important when the process signal has ripple or noise. The onsemi LM2903N datasheet provides the authoritative electrical limits for the onsemi ordering code.

🌐

Open-Collector Logic Interfacing

The LM2903N-NS supports open-collector logic interfacing because its outputs can pull a shared bus low while external pull-up resistors establish the high state. This arrangement can connect a comparator decision to a wired-AND function, isolate a fault line, or translate a system voltage through the pull-up network. Two independent channels provide flexibility when one event must acknowledge or mask another. The design must verify that the aggregate sink current of all connected outputs remains within the device limit and that the pull-up voltage is permissible. The onsemi LM2903N datasheet gives the output-current and electrical-characteristic criteria for that assessment.

What is the onsemi LM2903N-NS?
The onsemi LM2903N-NS is a dual, independent precision voltage comparator with open-collector outputs in an 8-pin PDIP package. According to the onsemi LM2903N datasheet, each channel compares an inverting and a non-inverting input, and the family supports single-supply or split-supply operation. Its low input offset is specified as low as 2.0 mV maximum for the LM193/LM2903 family.
Where can I download the LM2903N-NS datasheet PDF?
The LM2903N-NS documentation is available through the onsemi LM2903N datasheet listing at the linked manufacturer-document repository. The onsemi LM2903N datasheet describes the dual independent precision comparators, single-supply and split-supply operation, open-collector behavior, electrical limits, and package pin assignments. Use that document for the authoritative ordering information and the exact -NS suffix parameters.
What is the LM2903N-NS pinout?
The LM2903N-NS uses the standard 8-pin comparator arrangement: pin 1 is OUT1, pins 2 and 3 are IN1− and IN1+, pin 4 is GND, pins 5 and 6 are IN2+ and IN2−, pin 7 is OUT2, and pin 8 is VCC. The onsemi LM2903N datasheet pin configuration should be checked against the final device ordering table before PCB release because exposed-pad or package variants must not be mixed.
Does the LM2903N-NS work with a single supply?
Yes, the LM2903N-NS is designed for single-supply operation as well as split supplies. According to the onsemi LM2903N datasheet description, the single-supply common-mode range extends to ground, which allows both inputs to operate close to the lower supply rail. The precise input and supply limits must still be respected, especially when the output must resolve logic levels near the supply rails.
What is the input offset voltage of the LM2903N-NS?
The LM193/LM2903 family is described by onsemi as having an offset voltage specification as low as 2.0 mV maximum for two comparators. The onsemi LM2903N datasheet defines the applicable test conditions and individual limits. This low-offset capability is useful when the compared voltages are close, although input bias, output saturation, and circuit-generated hysteresis also affect the practical switching point.
Why does the LM2903N output need a pull-up resistor?
Each LM2903N output is an open-collector transistor that can actively pull its output low but cannot actively drive a high voltage. A suitable pull-up resistor or pull-up logic is therefore required. According to the onsemi LM2903N datasheet, designers must select the pull-up voltage and resistance so that the resulting high level, sink current, and total output current remain within the device electrical limits.
LM2903N-NS vs LM2903N — which one should I select?
Choose the exact LM2903N-NS ordering code when the required manufacturer, package, qualification, and lead-free suffix are part of the production specification. The LM2903N-NS and the shorter LM2903N listing can refer to related catalog entries, but suffixes may change packaging or qualification rather than only price. Compare the onsemi LM2903N datasheet ordering table, package marking, and environmental requirements before substitution.
When should I choose the LM2903N-NS over a single-channel comparator?
Choose the LM2903N-NS when the design needs two independent threshold decisions in one through-hole package. Two channels can implement separate upper and lower limits, a voltage window, or two sensor-protection functions while reducing package count. According to the onsemi LM2903N datasheet, the channels operate independently, but each still requires its own input definition, output pull-up, and compliance with the shared supply and ground limits.
What can replace the LM2903N-NS?
The closest replacements must use the same 8-pin PDIP footprint, preserve the comparator pin functions, and provide equivalent open-collector behavior. The STMicroelectronics LM2903N and NXP Semiconductors LM2903N are relevant dual-comparator alternatives to evaluate, while Texas Instruments LM2903N/NOPB is another 8-pin PDIP option. According to the respective manufacturer datasheets, verify input limits, offset, output-current capability, and qualification before treating any candidate as a drop-in replacement.
Is the STMicroelectronics LM2903N a drop-in replacement for LM2903N-NS?
The STMicroelectronics LM2903N is a strong functional candidate because it is an 8-DIP dual open-collector comparator, but it should be treated as a manufacturer-specific alternative rather than an automatic substitution. According to the STMicroelectronics LM2903N datasheet, engineers should compare supply range, common-mode limits, input offset, output sink current, operating temperature, and package pinout against the onsemi LM2903N-NS requirements before PCB release.
Where to buy the LM2903N-NS online?
Use the Request a Quote form on this page to request LM2903N-NS availability, current commercial terms, and a firm lead time for the required quantity. The onsemi LM2903N datasheet and ordering information define the supported configuration, while procurement should confirm the exact -NS suffix, manufacturer, and package. Requesting the quote avoids relying on a generic LM2903N listing that may represent a different manufacturer or ordering code.
What is the price of the LM2903N-NS?
Current pricing and volume breaks for the exact LM2903N-NS should be requested through the Request a Quote form on this page. The onsemi LM2903N datasheet confirms the device family but is not a current commercial quotation, and generic LM2903N listings may correspond to another manufacturer. Include your annual usage, forecast, required package markings, and delivery schedule when requesting an exact quote.
What is the lead time and stock status for LM2903N-NS?
The Request a Quote form on this page is the appropriate route for current stock status, minimum order quantity, and production lead time for the exact onsemi LM2903N-NS. Lead time can change with ordering code, package, quantity, and market conditions, so a generic LM2903N inventory result is not sufficient. Provide the required quantity and schedule so procurement can confirm an actionable delivery commitment.
Is the LM2903N-NS suitable for industrial sensor monitoring?
Yes, the LM2903N-NS is suitable for threshold-based industrial sensor monitoring when its electrical limits match the signal and supply ranges. According to the onsemi LM2903N datasheet, the two independent channels can monitor separate sensor thresholds, and single-supply common-mode operation extends toward ground. Add positive feedback for hysteresis when sensor noise is close to the switching point.
What are the key specifications engineers should know about LM2903N-NS?
The key LM2903N-NS specifications are two independent precision comparator channels, open-collector outputs, operation from a single or split supply, and an 8-pin PDIP package. According to the onsemi LM2903N datasheet, family input offset can be as low as 2.0 mV maximum, while single-supply common-mode operation extends to ground. Each open-collector output still requires an external pull-up and suitable current limiting.
Does the LM2903N-NS meet RoHS and REACH requirements?
The exact onsemi LM2903N-NS compliance status should be confirmed against the manufacturer product declaration and the applicable ordering code before release. The onsemi LM2903N datasheet is the controlling technical document, while material-compliance statements are normally published separately for a specific package and manufacturing configuration. Do not infer RoHS, REACH, lead-free, or automotive qualification from the LM2903 family name alone.

के लिए इंजीनियरिंग संदर्भ डेटा LM2903N-NS — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the LM2903N-NS when the design requires two independent precision comparisons, open-collector outputs, and an 8-pin PDIP footprint. It is particularly suitable for single-supply threshold detection, voltage-window monitoring, and protection functions where the compared signals remain within the comparator's common-mode limits. The STMicroelectronics, NXP Semiconductors, Texas Instruments, and HGSEMI LM2903N options can be evaluated as same-footprint alternatives, but their manufacturer-specific electrical limits, qualification, temperature range, and ordering codes must be checked before substitution. Choose a single-channel comparator when only one decision path is required and board area is less important than simplifying the design. Use the LM2903N-NS when two independent channels provide a clear functional advantage, but retain external pull-up resistors, defined input states, and deliberate hysteresis wherever the compared signals may cross slowly or contain noise.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद LM2903N LM2903N LM2903N LM2903N/NOPB LM2903N
Brand onsemi onsemi STMicroelectronics NXP Semiconductors Texas Instruments HGSEMI
Package PDIP-8 PDIP-8 PDIP-8 PDIP-8 PDIP-8 PDIP-8
Comparator Count 2 independent channels 2 independent channels 2 independent channels 2 independent channels 2 independent channels 2 independent channels
Output Type Open collector Open collector Open collector Open collector Open collector Open collector
Supply Operation Single supply or split supply Single supply or split supply Single supply or split supply Single supply or split supply Single supply or split supply Single supply or split supply
Mounting Style Through-hole Through-hole Through-hole Through-hole Through-hole Through-hole
Pin Count 8 pins 8 pins 8 pins 8 pins 8 pins 8 pins

मुख्य विशेषताएँ

  • Two independent precision comparator channels in one package (बनामLM2901M)
  • Open-collector output supports wired logic and flexible pull-up voltage (बनामTLV7022)
  • Single-supply common-mode operation extends toward ground (बनामLM2902N/PB)

डिज़ाइन नोट्स

Do not treat the open-collector output as a push-pull logic output. Each output requires a pull-up resistor or suitable pull-up logic before it can present a valid high state. Size the resistor from the required sink current and desired rise time, and verify that simultaneous low outputs do not exceed the device's total output-current limit. The onsemi LM2903N datasheet defines the applicable output constraints.

Add intentional hysteresis when either input can vary slowly or carry noise. A small positive-feedback resistor from an output to its non-inverting input separates the switching thresholds and prevents repeated transitions around the reference voltage. Check that this feedback does not distort the intended threshold or exceed the output-current limit, especially when both channels share the same reference network.

Keep the comparator inputs and their reference components away from switching-power nodes and high-current return paths. Place the open-collector pull-up resistors close to the output pins to minimize trace area and ringing. Maintain a low-impedance ground return for pin 4, and review the complete common-mode and supply ranges before connecting a sensor whose output may exceed the comparator input limits.

Decouple the supply pin near the package with the capacitance recommended by the manufacturer, and account for the fact that the family supply-current drain is independent of supply-voltage magnitude. Do not assume a comparator output can safely sink the pull-up current at every supply voltage; calculate the worst-case sink condition and account for temperature-dependent output characteristics.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

Exact onsemi LM2903N-NS material-compliance declarations were not identified. Automotive qualification is not claimed for the standard LM2903N-NS ordering code.

डेटा सत्यापन तिथि: 2026-11-13 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

lm2903n datasheet lm2903n pinout lm2903 datasheet pdf lm2903n pdf LM2903N-NS datasheet LM2903N-NS pinout LM2903N-NS equivalent LM2903N-NS replacement LM2903N-NS DIP-8 comparator onsemi LM2903N-NS LM2903N-NS price LM2903N-NS stock

संबंधित कंपोनेंट्स और शब्द

onsemi LM2903N-NS LM2903N STMicroelectronics LM2903N NXP Semiconductors LM2903N Texas Instruments LM2903N/NOPB voltage comparator dual comparator precision comparator analog integrated circuit semiconductor open-collector output single-supply operation split-supply operation common-mode voltage input offset voltage PDIP-8 DIP package through-hole mount surface mount hysteresis industrial sensor monitoring battery protection voltage-window monitor
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें