LM324ADTBR2 - Quad 3-26V Op Amp, 14-TSSOP | onsemi
MPN: LM324ADTBR2 ✓ نشطLM324ADTBR2 نظرة عامة
An operational amplifier is a high-gain analog amplifier intended for closed-loop signal conditioning. The LM324 belongs to the broader operational amplifier, analog amplifier, and integrated-circuit hierarchy. Its differential inputs compare two voltages and drive an output according to the feedback network. True differential inputs are particularly useful in single-supply circuits, where an input signal can be referenced near ground without requiring a split bipolar power supply.
The principal characteristics include four amplifiers per package, a 3 V to 26 V operating range, 3 mV input offset voltage, and approximately 0.6 V/us slew rate. The 14-TSSOP package provides a compact surface-mount format for general-purpose analog designs. The manufacturer identifies the LM324 series as a low-cost family with true differential inputs and several advantages over standard operational-amplifier types in single-supply applications.
Each amplifier can be configured for voltage amplification, buffering, summing, filtering, or differential signal conditioning when suitable external resistors and capacitors are used. Because the LM324 contains four independent channels, designers can reduce component count in multi-channel instrumentation, sensor-conditioning, and feedback-control circuits. Independent channels also provide flexibility when different stages require different gain values or operating conditions.
Typical uses include low-cost sensor interfaces, analog measurement chains, audio and communication equipment, power-supply feedback, and industrial control modules. In each case, the designer must verify input common-mode range, output swing, gain-bandwidth behavior, input bias current, and stability for the selected feedback network before releasing a production design.
The main design consideration is the input common-mode range. A signal-sensing circuit should keep both inputs inside the amplifier's permitted common-mode window throughout its operating range. Decoupling capacitors should be placed close to the supply pins, while resistor and capacitor values should be calculated for the intended gain and bandwidth rather than copied without verification.
This page consolidates electrical characteristics, package details, application guidance, practical design considerations, and qualified drop-in comparison information for engineers evaluating the LM324ADTBR2.
بدائل مباشرة لـ LM324ADTBR2 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM324ADTBR2 (نفس عامل الشكل والبصمة) — يختلف في Amplifier Type, Input Type, Supply Voltage Range.
LM324ADTBR2G
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM324ADTBR2 الحدود القصوى والخصائص الكهربائية
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Input Type | True differential input |
| Supply Voltage Range | 3 V to 26 V |
| Maximum Supply Voltage | 32 V |
| Differential Supply Voltage | ±16 V |
| Input Offset Voltage | 3 mV |
| Slew Rate | 0.6 V/us |
| نطاق درجة حرارة التشغيل | -40 °C to +105 °C |
| العلبة | 14-pin TSSOP |
| نوع التركيب | Surface mount |
| Shipping Format | Tape and reel |
دليل تكوين أطراف LM324ADTBR2 14-pin tssop
تكوين الأطراف لـ LM324ADTBR2 (حزمة 14-pin tssop). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM324ADTBR2.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LM324ADTBR2 مناسب لـ 6 التطبيقs: Single-Supply Sensor Conditioning, Industrial Control and Instrumentation, Audio Preamplifier and Mixer, Power-Supply Feedback and Monitoring, Communications Interface Circuitry, General-Purpose Buffering and Active Filtering.
Single-Supply Sensor Conditioning
The LM324ADTBR2 fits four-channel sensor signal conditioning because each of its four amplifiers has true differential inputs and the device operates from 3 V to 26 V. A Wheatstone bridge, temperature sensor, or resistive sensor can feed a differential stage while the feedback network sets gain and bandwidth. The listed 3 mV input offset and 0.6 V/us slew rate must be compared with the sensor’s resolution and required settling time. Common-mode voltage remains the principal constraint: signals must remain inside the manufacturer’s permitted input range. The TSSOP package also permits placement near the sensor connector, reducing sensitive-signal trace length.
موصى به
Industrial Control and Instrumentation
The four independent amplifiers in the LM324ADTBR2 allow a compact industrial control module to implement several low-level analog stages without using four separate packages. Typical channels include sensor amplification, actuator-error amplification, reference buffering, and feedback monitoring. Its 3 V to 26 V supply capability is useful for systems whose rail is above a conventional 5 V level, while the 14-pin TSSOP simplifies compact surface-mount assembly. Engineers should verify input bias current, output current capability, noise, and output swing against the selected sensor and actuator. Industrial temperature and electromagnetic-compatibility requirements should also be handled at the board and qualification levels.
موصى به
Audio Preamplifier and Mixer
LM324ADTBR2 can implement four general-purpose audio preamplifier, summing, or mixing channels when the design does not require rail-to-rail operation or very low distortion. The true differential inputs support balanced source arrangements, and the 3 mV listed input offset is acceptable for many line-level and general audio paths. Its 0.6 V/us slew rate must be checked against the highest expected signal frequency and load. Input and output coupling networks should block DC, while feedback resistors determine gain and bandwidth. The TSSOP package helps reduce board area, although exposed-package soldering and thermal performance should be controlled during assembly.
موصى به
Power-Supply Feedback and Monitoring
The LM324ADTBR2 can monitor a regulated rail and amplify the difference between a feedback divider and a reference. One channel may serve the main feedback amplifier, while additional channels monitor input voltage, output current, or fault signals. Its 3 V to 26 V operating range allows use in 5 V, 12 V, and 24 V systems, but the input common-mode range must cover the feedback-node voltage. The 3 mV listed offset contributes directly to output-power accuracy, so divider tolerances and precision-resistor requirements should be evaluated together. A 14-pin TSSOP package allows the feedback electronics to be placed close to the power stage.
موصى به
Communications Interface Circuitry
LM324ADTBR2 is applicable to low-speed communications interfaces that need multiple buffering, gain, level-shifting, or receive-path amplification functions. The quad configuration can reduce package count in equipment with several analog channels, and operation from 3 V to 26 V supports both compact and industrial supply systems. Designers must account for the 0.6 V/us slew rate, output settling, capacitive loading, and the non-rail-to-rail input or output behavior when defining logic thresholds. Proper grounding and short feedback paths are important for preserving signal integrity. A TSSOP package can shorten sensitive traces, although fanout and routing should remain consistent with the manufacturer’s land pattern.
موصى به
General-Purpose Buffering and Active Filtering
The LM324ADTBR2 can provide four unity-gain buffers or four stages of an active filter when the signal bandwidth is within the amplifier’s capability. Voltage followers isolate higher-impedance sources from downstream loads, while repeated RC feedback networks can construct low-pass, high-pass, or band-pass sections. The 0.6 V/us slew rate places a practical ceiling on large-signal output transitions, and the 3 mV listed input offset affects DC accuracy in precision filter stages. Component tolerances, amplifier input bias current, and load capacitance should be considered together. Placing the active-filter components close to each associated amplifier minimizes parasitic feedback and improves channel matching.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM324ADTBR2 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM324ADTBR2G |
|---|---|---|
| Package | 14-pin TSSOP | 14-pin TSSOP |
| Brand | onsemi | onsemi |
| Amplifier Count | 4 circuits | 4 circuits |
| Operating Supply Range | 3 V to 26 V | 3 V to 32 V |
| Maximum Supply Voltage | 32 V | 32 V |
| Slew Rate | 0.6 V/us | 0.6 V/us |
| Input Type | True differential input | True differential input |
أبرز الفروقات
- Four true-differential amplifiers in one compact package (مقابلLM324AMX/NOPB)
- Identified same-package onsemi alternative (مقابلLM324ADTBR2G)
- Single-supply operation aligned with 24 V industrial rails (مقابلLM324AMX/NOPB)
ملاحظات التصميم
Check the input common-mode range before accepting a new circuit. The 3 V to 26 V supply rating does not imply that the amplifier inputs can follow the full supply voltage. Bias the input network so both inputs remain within the range stated in the onsemi LM324 datasheet at the minimum supply, maximum signal, and highest expected temperature. This is especially important for battery-powered and 3.3 V designs where a nominal midpoint can exceed the permitted common-mode window.
Place input, output, feedback, and bypass components close to their associated TSSOP pins. Keep supply decoupling traces short and use a compact ground reference to reduce parasitic inductance. Because the package contains four amplifiers, number the channels in the schematic and PCB consistently so feedback does not cross between sections. Use the manufacturer land pattern and paste geometry for assembly rather than estimating dimensions from the package drawing.
Calculate the required settling time from the intended closed-loop bandwidth and the listed 0.6 V/us slew rate. A low-frequency gain stage may be satisfactory, while a higher-bandwidth design can become slew-rate limited before reaching its small-signal bandwidth limit. Keep feedback resistors reasonably low where capacitive loading and parasitic capacitance are significant, and verify that the selected output load does not exceed the manufacturer’s specified operating conditions.
Decouple each supply rail locally and account for the total quiescent current of four amplifiers when sizing the supply path. The 3 mV listed input offset affects DC accuracy directly, so divider and feedback-resistor tolerances can be as important as the amplifier offset. For instrumentation designs, calculate the full error budget from sensor tolerance, resistor tolerance, input bias effects, output swing, and the LM324’s offset specification rather than treating the amplifier as an ideal component.
معلومات الامتثال
No target-specific compliance declaration was identified. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status with onsemi before release to production.