LM358ADR2GH - Dual 3-32V Op Amp | onsemi | Industrial
MPN: LM358ADR2GH ✓ نشطLM358ADR2GH نظرة عامة
A general-purpose operational amplifier is a voltage-controlled amplifier that uses external feedback to amplify voltage differences. LM358-type devices belong to the operational-amplifier hierarchy, combining differential input, high open-loop gain, output-current capability, and common-mode input operation. The onsemi LM358 family is widely used in instrumentation, buffer-amplifier, sensor-conditioning, and general feedback-control circuits where a dual amplifier provides more functionality than a single-channel device in the same package.
The LM358ADR2GH provides two amplifier circuits, operates from 3 V to 32 V, and is identified as a commercial-temperature dual improved input-offset-voltage amplifier. Its listed slew rate is 0.6 V/us, while its gain-bandwidth product is not stated in the available product information. The device also supports single-supply or split-supply operation and has a common-mode input-voltage range extending to ground or VEE, allowing useful operation in circuits powered from a single positive rail.
The 8-SOIC package has a stated body width of 3.90 mm, equivalent to 0.154 inch. Its dual-amplifier arrangement is useful when a circuit requires matched functional channels for signal conditioning, filtering, differential sensing, or feedback control. Because the operating and electrical limits vary with supply voltage, load, temperature, and configuration, designers should evaluate input common-mode range, output swing, stability, output-current capability, and offset behavior against their specific operating point before finalizing the circuit.
Typical applications include current sensing in industrial instrumentation, buffering sensor outputs, amplifying low-level control signals, active analog filters, and general-purpose feedback-control loops. In single-supply systems, the ground-referenced common-mode capability can simplify signal conditioning around sensors whose output remains near the lower supply rail. In split-supply systems, both amplifier channels can process bipolar signals around the midpoint of the supply.
PCB implementation should follow the manufacturer pin-description table and use a short, low-impedance feedback path. Place input, output, and compensation components close to the appropriate device pins, maintain a stable ground reference, and avoid long traces near switching nodes. Check the external feedback network for acceptable bandwidth and noise performance, and verify the chosen bypass capacitors against the application’s supply ripple and transient requirements.
This product page combines the exact orderable designation, verified listing attributes, practical op-amp design guidance, and clearly scoped replacement information. The accompanying comparisons emphasize the engineering checks required for an eight-pin SOIC footprint: rail-to-rail compatibility cannot be assumed from the LM358 name alone, and load current, common-mode range, slew rate, offset voltage, bandwidth, and temperature grade should be reviewed before approving a substitution.
بدائل مباشرة لـ LM358ADR2GH — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
SGMI8358
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TP358
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
BP358
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
NSMOP-358
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LM358ADR2GH الحدود القصوى والخصائص الكهربائية
| Amplifier Type | General Purpose |
| Number of Amplifier Circuits | 2 circuits |
| Supply Voltage Range | 3 V to 32 V |
| العلبة | 8-SOIC |
| Package Body Width | 3.90 mm (0.154 inch) |
| نوع التركيب | Surface Mount |
| Slew Rate | 0.6 V/us |
| Operating Temperature Grade | Commercial |
| Common-Mode Input Voltage Range | Extends to ground/VEE |
| Supply Configuration | Single supply or split supply |
دليل تكوين أطراف LM358ADR2GH 3.90 mm (0.154 inch)
تكوين الأطراف لـ LM358ADR2GH (حزمة 3.90 mm (0.154 inch)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM358ADR2GH.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LM358ADR2GH مناسب لـ 6 التطبيقs: Industrial Current Sensing, Sensor Signal Buffering, Active Analog Filtering, Power Supply Feedback Control, Audio and Communication Interface Conditioning, General-Purpose Feedback Control.
Industrial Current Sensing
The LM358ADR2GH is well suited to amplifying the small voltage produced by a current-sense shunt in industrial instrumentation. Its two amplifier channels can provide signal amplification and a buffered reference or auxiliary channel, while the 3 V to 32 V operating range supports both compact sensor nodes and higher-voltage control systems. The 0.6 V/us slew rate helps preserve signal shape, and the common-mode input range extending to ground or VEE supports single-supply sensing arrangements. For a new design, verify the selected sense-resistor magnitude, shunt common-mode voltage, amplifier input range, output swing, and offset error against the target measurement resolution.
موصى به
Sensor Signal Buffering
The LM358ADR2GH can buffer high-impedance sensor outputs before they drive an ADC or downstream instrumentation stage. Two channels provide flexible use for a noninverting buffer and a gain or filter section, while the 8-SOIC package keeps the circuit compact. Common-mode input operation extending to ground or VEE is useful when sensing voltages near the lower rail of a single-supply system. Confirm that the sensor’s output range remains inside the amplifier’s common-mode limits and that capacitive loading at the buffered output will not cause instability. Add input bias compensation when source impedance is high or output-offset drift is critical.
موصى به
Active Analog Filtering
The two LM358ADR2GH amplifier channels can implement first-order or cascaded analog filters when a low-frequency signal must be conditioned before digitization. Its listed 0.6 V/us slew rate and general-purpose architecture are appropriate for many instrumentation and control-bandwidth applications, and the 3 V to 32 V supply range allows the filter to share a broad range of system rails. The gain-bandwidth product and stability limits must be obtained from the manufacturer datasheet before setting closed-loop gain and capacitor values. Keep the feedback loop compact, use stable resistor and capacitor selections, and validate phase margin using the final source and load impedances.
موصى به
Power Supply Feedback Control
The LM358ADR2GH can be used in feedback-control loops for regulated laboratory, industrial, or communications power systems. Its two channels permit error amplification and an auxiliary comparison or buffer function, while the 3 V to 32 V operating range covers many control-board supply environments. A 0.6 V/us slew rate can be appropriate for moderate loop bandwidth, but compensation and stability depend on the power-stage topology, crossover frequency, and output impedance. Verify the allowed input and output excursions during startup and fault conditions, and ensure the amplifier does not saturate as the controlled rail changes.
موصى به
Audio and Communication Interface Conditioning
The LM358ADR2GH is appropriate for low-frequency audio and communication interface conditioning when rail-to-rail input operation is unnecessary. Two channels can support gain, attenuation, or active-filter stages around low-level signals, and the ground-referenced common-mode capability can simplify single-supply interfacing. Its 0.6 V/us slew rate provides margin for many low-bandwidth paths but may be insufficient for high-frequency audio or communication signals. Set the feedback network according to the manufacturer’s stability guidance, check distortion and output-current requirements, and keep sensitive input routing away from switching nodes and high-current return paths.
موصى به
General-Purpose Feedback Control
The LM358ADR2GH can amplify error signals in basic proportional control loops for valves, heaters, positioning systems, and laboratory mechanisms. Two channels allow an error amplifier to work alongside a buffer, reference follower, or auxiliary conditioning stage, and the 3 V to 32 V supply range supports many industrial control boards. The commercial-temperature grade should be checked against the ambient range of the final system. For stable operation, derive compensation from the actuator and plant dynamics, include output limiting, and verify the output swing and load current against the controlled load before deployment.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM358ADR2GH — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | SGMI8358 | TP358 | BP358 | NSMOP-358 |
|---|---|---|---|---|---|
| Brand | onsemi | SGMC (Sagna Microelectronics) | 3PEAK | 3PEAK | NSC (Natron Semiconductor) |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Channels | 2 | 2 | 2 | 2 | 2 |
أبرز الفروقات
- Wide supply operating range (مقابلSGMI8358)
- Commercial-temperature dual general-purpose positioning (مقابلTP358)
- Established onsemi orderable family (مقابلBP358)
- Two amplifier channels in one 8-SOIC package (مقابلNSMOP-358)
ملاحظات التصميم
Route each amplifier channel as a compact analog signal path. Place feedback resistors and compensation capacitors directly beside their associated pins, keep non-inverting input traces short, and provide a low-impedance ground plane beneath the SOIC-8 footprint. Separate the analog signal path from switching-node and high-current supply traces. This is particularly important because a long feedback route can add phase delay and create stability problems that are not apparent from nominal gain-bandwidth figures alone.
The device accepts a 3 V to 32 V supply, but that range does not imply that every input and output combination is valid at every supply voltage. Check the common-mode input region, output swing, and output-current limit at the lowest and highest intended supply voltages. Add local supply bypassing with short ground returns, and verify the source impedance seen by each amplifier during startup. Also account for input overvoltage during power sequencing or fault conditions.
Do not assume that every LM358-compatible amplifier is interchangeable solely because its package and pinout match. A replacement can differ in input offset, common-mode range, output swing, bandwidth, slew rate, noise, load capability, shutdown behavior, and temperature grade. Compare those limits with the actual circuit, especially when driving capacitive loads, operating near the input range boundary, or requiring the full 3 V to 32 V supply range.
The 8-SOIC package provides a practical thermal path, but the allowable dissipation still depends on supply voltage, output swing, load current, ambient temperature, and board copper. Reduce dissipation by minimizing the voltage drop across the output stage and avoiding sustained operation near the output-current limit where possible. Place the device near adequate ground-plane area and avoid placing it beside a heat source or in an enclosure with restricted airflow.
معلومات الامتثال
The verified product listings identify the onsemi LM358ADR2GH family and commercial operating grade but do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.